Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “compression rate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Temperature distortion generator for turboshaft engine testing

The procedures and unique hardware used to conduct an experimental investigation into the response of a small-turboshaft-engine compression system to various hot gas ingestion patterns are presented. The temperature distortion generator described herein uses gaseous hydrogen to create both steady-state and time-variant, or transient, temperature distortion at the engine inlet. The range of transient temperature ramps produced by the distortion generator during the engine tests was from less than 111 deg K/sec (200 deg R/sec) to above 611 deg K/sec (1100 deg R/sec); instantaneous temperatures to 422 deg K (760 deg R) above ambient were generated. The distortion generator was used to document the maximum inlet temperatures and temperature rise rates that the compression system could tolerate before the onset of stall for various circumferential distortions as well as the compressor system response during stall.

Klann, G. A.↗
NASA NTRS1978

Strain-rate/temperature behavior of high density polyethylene in compression

The compressive strain rate/temperature behavior of highly linear, high density polyethylene was analyzed in terms of the predictive relations developed for metals and other crystalline materials. For strains of 5 percent and above, the relationship between applied strain rate, dotted epsilon, and resulting flow stress, sigma, was found to be: dotted epsilon exp times (Q sub f/RT) = k'(sigma/sigma sub c) to the nth power; the left-hand side is the activation-energy-compensated strain rate, where Q sub f is activation energy for flow, R is gas constant, and T is temperature; k is a constant, n is temperature-independent stress exponent, and sigma/sigma sub c is structure-compensated stress. A master curve resulted from a logarithmic plot of activation-energy-compensated strain rate versus structure-compensated stress.

Clements, L. L.↗
NASA NTRS1993

Compressibility Effects on the Growth and Structure of Homogeneous Turbulent Shear Flow

Compressibility effects within decaying isotropic turbulence and homogeneous turbulent shear flow have been studied using direct numerical simulation. The objective of this work is to increase our understanding of compressible turbulence and to aid the development of turbulence models for compressible flows. The numerical simulations of compressible isotropic turbulence show that compressibility effects are highly dependent on the initial conditions. The shear flow simulations, on the other hand, show that measures of compressibility evolve to become independent of their initial values and are parameterized by the root mean square Mach number. The growth rate of the turbulence in compressible homogeneous shear flow is reduced compared to that in the incompressible case. The reduced growth rate is the result of an increase in the dissipation rate and energy transfer to internal energy by the pressure-dilatation correlation. Examination of the structure of compressible homogeneous shear flow reveals the presence of eddy shocklets, which are important for the increased dissipation rate of compressible turbulence.

Blaisdell, G. A.↗
NASA NTRS1993

A CAM-based LZ data compression IC

A custom CMOS processor is introduced that implements the Data Compression Lempel-Ziv (DCLZ) standard, a variation of the LZ2 Algorithm. This component presently achieves a sustained compression and decompression rate of 10 megabytes/second by employing an on-chip content-addressable memory for string table storage.

Winters, K.↗
NASA NTRS1996

Analysis of Compressible Mixing Layers Using Dilatational Covariances Model

Compressible mixing layers are analyzed using a dilatational covariances model based on a pseudo-sound constitutive relation. The calculations are used to evaluate the different physical phenomena affecting compressible mixing layers. The rate of growth of the mixing layer is retarded by both the compressible dissipation and the pressure-dilatational covariances. The pressure-dilatational, essentially a nonequilibrium effect, reduces the amount of excess production over dissipation available for the turbulence energy growth. The pseudo-sound model also includes a history dependent portion: this is also investigated. All constants in the model and used in these computations are predicted by the theory.

Thangam, S.↗
NASA NTRS2006

Elastomeric Seal Development for Advanced Docking/Berthing System

Elastomeric seals ar Elastomeric seals are being considered for application to the Advanced Docking / Berthing System. Currently, three candidate elastomers are being evaluated. To meet the unique requirements of the ADBS, several test fixtures have been built to determine each elastomer s Environmental and operating temperature compatibility Material stability when exposed to Atomic Oxygen and Ultraviolet radiation Adhesion force required to separate Compression set Leak rate These results will be compared with those from the metallic seal development to determine the final seal design

Daniels, Christopher↗
NASA NTRS1940

Wind-tunnel Tests of the NACA 45-125 Airfoil: A Thick Airfoil for High-Speed Airplanes

Investigations of the pressure distribution, the profile drag, and the location of transition for a 30-inch-chord 25-percent-thick N.A,C.A. 45-125 airfoil were made in the N.A.C.A 8-foot high-speed wind tunnel for the purpose of aiding in the development of a thick wing for high-speed airplanes. The tests were made at a lift coefficient of 0.1 for Reynolds Numbers from 1,750,000 to 8,690,000, corresponding to speeds from 80 to 440 miles per hour at 59 F. The effect on the profile drag of fixing the transition point was also investigated. The effect of compressibility on the rate of increase of pressure coefficients was found to be greater than that predicted by a simplified theoretical expression for thin wings. The results indicated that, for a lift coefficient of 0.1, the critical speed of the N.A.C,A. 45-125 airfoil was about 460 miles per hour at 59 F,. The value of the profile-drag coefficient at a Reynolds Number of 4,500,000 was 0.0058, or about half as large as the value for the N.A,C,A. 0025 airfoil. The increase in the profile-drag coefficient for a given movement of the transition point was about three times as large as the corresponding increase for the N.A.C,A. 0012 airfoil. Transition determinations indicated that, for Reynolds Numbers up to ?,000,000, laminar boundary 1ayers were maintained over approximately 40 percent of the upper and the lower surfaces of the airfoil.

Delano, James B.↗
NASA NTRS2017

Development of an Input Suite for an Orthotropic Composite Material Model

An orthotropic three-dimensional material model suitable for use in modeling impact tests has been developed that has three major components elastic and inelastic deformations, damage and failure. The material model has been implemented as MAT213 into a special version of LS-DYNA and uses tabulated data obtained from experiments. The prominent features of the constitutive model are illustrated using a widely-used aerospace composite the T800S3900-2B[P2352W-19] BMS8-276 Rev-H-Unitape fiber resin unidirectional composite. The input for the deformation model consists of experimental data from 12 distinct experiments at a known temperature and strain rate: tension and compression along all three principal directions, shear in all three principal planes, and off axis tension or compression tests in all three principal planes, along with other material constants. There are additional input associated with the damage and failure models. The steps in using this model are illustrated composite characterization tests, verification tests and a validation test. The results show that the developed and implemented model is stable and yields acceptably accurate results.

finite element method↗
NASA NTRS1975

On the source of lunar limb compressions

Magnetic-field measurements made on board the Apollo 15 and 16 subsatellites in low-altitude lunar orbit are used to study compressions of the magnetic field over terminator regions when the moon is in the solar wind. These compressional disturbances occur at just in front of the terminator, but only when specific selenographic regions appear at the lunar limb. The occurrence rate, strength, and position of the compression relative to the limb are different for each source region. Where overlaps of limb-compression occurrence statistics and lunar magnetic-field maps exist, the limb-compression occurrence rates have a high degree of correlation with magnetic-field strength. Thus the most probable cause of limb compressions is deflection of the solar wind by the lunar surface magnetic field as the solar wind flows past the lunar terminators.

Russell, C. T.↗
NASA NTRS1973

A zero-error operational video data compression system

A data compression system has been operating since February 1972, using ATS spin-scan cloud cover data. With the launch of ITOS 3 in October 1972, this data compression system has become the only source of near-realtime very high resolution radiometer image data at the data processing facility. The VHRR image data are compressed and transmitted over a 50 kilobit per second wideband ground link. The goal of the data compression experiment was to send data quantized to six bits at twice the rate possible when no compression is used, while maintaining zero error between the transmitted and reconstructed data. All objectives of the data compression experiment were met, and thus a capability of doubling the data throughput of the system has been achieved.

Kutz, R. L.↗
NASA NTRS1991

Modeling the rapid spherical compression of isotropic turbulence

Rapid distortion analysis is used to modify the form of the closure model for the dissipation rate of the turbulent kinetic energy. The modification is such that the evolution of the dissipation rate during a rapid compression is predicted exactly; good agreement between the model prediction and direct simulation data is obtained. Previous closure proposals fail to properly predict the rapid compression case. The reason for the difference between the present and previous models is traced to the fact that previous workers neglected variations of kinematic viscosity.

Coleman, Gary N.↗
NASA NTRS1975

Lunar topography and the limb compression source regions

Data from the Apollo 15, 16, and 17 laser altimeters have been used to study slopes, elevations, and roughness in the identifiable regions on the moon which sporadically produce plasma compressions and magnetic-field enhancements in the solar wind/lunar void boundary when those regions are at a flow limb. It is found that occurrence rates for such 'limb compressions' derived from Explorer 35 satellite measurements are significantly correlated with peak, average, and RMS slopes in the source regions, whereas rates derived from Apollo 15 and 16 subsatellite data are not correlated with topography. This suggests that two or more mechanisms operate in the source regions to produce limb compressions. Together with the known correlation between limb compressions and local surface remanent magnetic fields, the results indicate that lunar magnetization is not strongly related to surface features.

Srnka, L. J.↗
NASA NTRS1976

Fatigue crack growth at elevated temperature 316 stainless steel and H-13 steel

Crack growths were measured at elevated temperatures under four types of loading: pp, pc, cp, and cc. In H-13 steel, all these four types of loading gave nearly the same crack growth rates, and the length of hold time had negligible effects. In AISI 316 stainless steel, the hold time effects on crack growth rate were negligible if the loading was tension-tension type; however, these effects were significant in reversed bending load, and the crack growth rates under these four types of loading varied considerably. Both tensile and compressive hold times caused increased crack growth rate, but the compressive hold period was more deleterious than the tensile one. Metallographic examination showed that all the crack paths under different types of loading were largely transgranular for both CTS tension-tension specimens and SEN reversed cantilever bending specimens. In addition, an electric potential technique was used to monitor crack growth at elevated temperature.

Chen, W. C.↗
NASA NTRS2017

Large-Eddy Simulation (LES) of a Compressible Mixing Layer and the Significance of Inflow Turbulence

In the context of Large Eddy Simulations (LES), the effects of inflow turbulence are investigated through the Synthetic Eddy Method (SEM). The growth rate of a turbulent compressible mixing layer corresponding to operating conditions of GeobelDutton Case 2 is investigated herein. The effects of spanwise width on the growth rate of the mixing layer is investigated such that spanwise width independence is reached. The error in neglecting inflow turbulence effects is quantified by comparing two methodologies: (1) Hybrid-RANS-LES methodology and (2) SEM-LES methodology. Best practices learned from Case 2 are developed herein and then applied to a higher convective mach number corresponding to Case 4 experiments of GeobelDutton.

les↗
NASA NTRS1931

The effectiveness of a double-stem injection valve in controlling combustion in a compression-ignition engine

An investigation was made to determine to what extent the rates of combustion in a compression-ignition engine can be controlled by varying the rates of fuel injection. The tests showed that the double-stem valve operated satisfactorily under all normal injection conditions; the rate of injection has a definite effect on the rate of combustion; the engine performance with the double-stem valve was inferior to that obtained with a single-stem valve; and the control of injection rates permitted by an injection valve of two stages of discharge is not sufficient to effect the desired rates of combustion.

Spanogle, J A↗
NASA NTRS1975

ITOS VHRR on-board data compression study

Data compression methods for ITOS VHRR data were studied for a tape recorder record-and playback application. A playback period of 9 minutes was assumed with a nominal 18 minute record period for a 2-to-1 compression ratio. Both analog and digital methods were considered with the conclusion that digital methods should be used. Two system designs were prepared. One is a PCM system and the other is an entropy-coded predictive-quantization, sometimes called entropy-coded DPCM or just DPCM, system. Both systems use data management principles to transmit only the necessary data. Both systems use a medium capacity standard tape recorder from specifications provided by the technical officer. The 10 to the 9th power bit capacity of the recorder is the basic limitation on the compression ratio. Both systems achieve the minimum desired 2 to 1 compression ratio. A slower playback rate can be used with the DPCM system due to a higher compression factor for better link performance at a given CNR in terms of bandwidth utilization and error rate. The report is divided into two parts. The first part summarizes the theoretical conclusions of the second part and presents the system diagrams. The second part is a detailed analysis based upon an empirically derived random process model arrived at from specifications and measured data provided by the technical officer.

Gray, R. M.↗
NASA NTRS2006

The Compressive Behavior of Isocyanate-crosslinked Silica Aerogel at High Strain Rates

Aerogels are low-density, highly nano-porous materials. Their engineering applications are limited due to their brittleness and hydrophilicity. Recently, a strong lightweight crosslinked silica aerogel has been developed by encapsulating the skeletal framework of amine-modified silica aerogels with polyureas derived by isocyanate. The mesoporous structure of the underlying silica framework is preserved through conformal polymer coating, and the thermal conductivity remains low. Characterization has been conducted on the thermal, physical properties and the mechanical properties under quasi-static loading conditions. In this paper, we present results on the dynamic compressive behavior of the crosslinked silica aerogel (CSA) using a split Hopkinson pressure bar (SHPB). A new tubing pulse shaper was employed to help reach the dynamic stress equilibrium and constant strain rate. The stress-strain relationship was determined at high strain rates within 114-4386/s. The effects of strain rate, density, specimen thickness and water absorption on the dynamic behavior of the CSA were investigated through a series of dynamic experiments. The Young's moduli (or 0.2% offset compressive yield strengths) at a strain rate approx.350/s were determined as 10.96/2.08, 159.5/6.75, 192.2/7.68, 304.6/11.46, 407.0/20.91 and 640.5/30.47 MPa for CSA with densities 0.205, 0.454, 0.492, 0.551,0.628 and 0.731 g/cu cm, respectively. The deformation and failure behaviors of a native silica aerogel with density (0.472 g/cu cm ), approximately the same as a typical CSA sample were observed with a high speed digital camera. Digital image correlation technique was used to determine the surface strains through a series of images acquired using high speed photography. The relative uniform axial deformation indicated that localized compaction did not occur at a compressive strain level of approx.17%, suggesting most likely failure mechanism at high strain rate to be different from that under quasi-static loading condition. The Poisson s ratio was determined to be 0.162 in nonlinear regime under high strain rates. CSA samples failed generally by splitting, but were much more ductile than native silica aerogels.

Luo, H.↗
NASA NTRS1983

Effect of swaging on the 1000 C compressive slow plastic flow characteristics of the directionally solidified eutectic alloy gamma/gamma prime-alpha

Swaging between 750 and 1050 C has been investigated as a means to introduce work into the directionally solidified eutectic alloy gamma/gamma prime-alpha (Ni-32.3 wt percent Mo-6.3 wt percent Al) and increase the elevated temperature creep strength. The 1000 C slow plastic compressive flow stress-strain rate properties in air of as-grown, annealed, and worked nominally 10 and 25 percent materials have been determined. Swaging did not improve the slow plastic behavior. In fact large reductions tended to degrade the strength and produced a change in the deformation mechanism from uniform flow to one involving intense slip band formation. Comparison of 1000 C tensile and compressive strength-strain rate data reveals that deformation is independent of the stress state.

Whittenberger, J. D.↗