Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “composites dislocations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Stacking faults and interface roughening in semipolar (202{sup ¯}1{sup ¯}) single InGaN quantum wells for long wavelength emission

The microstructure of InGaN single quantum wells (QWs) grown in semipolar (202{sup ¯}1{sup ¯}) orientation on GaN substrates was studied by transmission electron microscopy. Stress relaxation in the lattice mismatch In{sub x}Ga{sub 1−x}N layer was realized by forming partial misfit dislocations associated with basal plane stacking faults (BPSFs). For given composition x = 0.24, BPSFs formation was observed when the QW thickness exceeded 4 nm. The high density of partial threading dislocations that bound the BPSFs is detrimental to light-emitting device performance. Interface roughening (faceting) was observed for both upper and lower QW interfaces (more pronounced for upper interface) and was found to increase with the thickness of the QW. BPSFs had a tendency to nucleate at roughened interface valleys.

36 MATERIALS SCIENCE↗

Plasticity in irradiated FeCrAl nanopillars investigated using discrete dislocation dynamics

Here, in this paper, we investigate plasticity in irradiated FeCrAl nanopillars using discrete dislocation dynamics simulations (DDD), with comparisons to transmission electron microscopic (TEM) in situ tensile tests of ion- and neutron-irradiated commercial C35M FeCrAl alloy. The effects of irradiation-induced defects, such as a/2<111> and a<100> type loops and composition fluctuations representative of phase separation in irradiated FeCrAl alloys, are investigated separately as well as superposed together in simulations. We explore the effects of defects on the stress-strain behavior, specifically yield strength and hardening response, of FeCrAl nanopillars. Our simulations confirm the widely accepted fact that irradiated alloys exhibit a stress-strain response with higher yield strength as compared to unirradiated alloys. However, our DDD calculations reveal an atypical superposition of the hardening contributions due to composition inhomogeneity and irradiation loops wherein composition inhomogeneity annihilates the hardening due to irradiation loops at small scales. As a result, we observe that the yield strength in irradiated alloys, after taking into consideration the effects of both composition inhomogeneity and irradiation loops, is smaller than the yield strength of the alloys with only irradiation loops and is approximately same for the alloy with composition inhomogeneity alone. This is referred to as “destructive interference” between the hardening contributions due to composition fluctuations and irradiation loops in the paper. We also identify this destructive interference in the superposition in our parallel TEM in situ tensile tests on unirradiated, ion-irradiated, and neutron-irradiated C35M FeCrAl alloy. This destructive interference in the hardening contributions contrasts with the dispersed barrier hardening (DBH) models widely utilized by the experimental community to model the hardening contributions due to different irradiation induced defects. The effects of the loading orientations on the yield strength and hardening are investigated and the mechanisms for the hardening in irradiated FeCrAl alloys are also reported.

36 MATERIALS SCIENCE↗

Strengthening of σ phase in a Fe20Cr9Ni cast austenite stainless steel

The strengthening mechanism of σ phase in a Fe20Cr9Ni cast austenite stainless steel used for primary coolant pipes of nuclear power plants has been investigated. The yield and ultimate tensile strengths of aged specimens increased comparing with those of the unaged ones. It was found that the increase of strengths is due to the hard and brittle (σ + γ{sub 2}) structure which decomposed from α phase in the steel. Fracture surfaces of specimens after in situ tensile test showed that the inhibition of (σ + γ{sub 2}) structure on the dislocation movements was more significant than ferrite although cracks started predominately at σ/γ{sub 2} interfaces. The (σ + γ{sub 2}) structure behaves like a fiber reinforced composite material. - Highlights: • The strengthening mechanism of σ phase in a Fe20Cr9Ni CASS is investigated. • The yield and ultimate tensile strengths increase with increasing of σ phase. • The increase of strengths is due to hard and brittle (σ + γ{sub 2}) structure. • The (σ + γ{sub 2}) structure in CASS behaves like a fibre reinforced composite material. • The σ/γ{sub 2} and α/σ/γ{sub 2} boundaries hinder the movement of dislocation.

36 MATERIALS SCIENCE↗

Screw-Dislocation-Driven Growth of 2D Perovskite Spiral Microplates

Two-dimensional (2D) organic–inorganic halide perovskites are solution-processable semiconductors that are promising for optoelectronic applications. Understanding crystallization mechanisms to achieve control over nanostructures is important for optimizing desired properties. Here we introduce a versatile strategy to synthesize spiral microplates of diverse 2D perovskites at the air–water interface through screw-dislocation-driven growth. Spirals of 11 2D perovskite compositions (LA) 2 (A) n−1 Pb n X 3n+1 with different spacer (LA) cations, A-cations, halide (X) anions, and n-number can be grown. They typically consist of single- or few-layer perovskite step heights but exhibit stacking complexity when multiple dislocations interact. The spiral microplates exhibit the characteristic optical properties (photoluminescence and second-harmonic generation) of the underlying 2D perovskites. Fluorescence-detected circular dichroism imaging shows that the chirality of the spiral center does not translate to the observed chiroptical properties of the microplate, consistent with the length scale of the chiral distortion. Furthermore, this solution growth of perovskite spirals diversifies the perovskite microstructures for optoelectronics and other applications.

2D halide perovskites↗

Effect of heat treatment on the tensile behavior of selective laser melted Ti-6Al-4V by in situ X-ray characterization

Selective Laser Melted Ti-6Al-4V (as-SLMed) exhibits decreased yield strength, increased work hardening, and increased ductility after heat treatment at 730 degrees C (HT-730) or 900 degrees C (HT-900) for 2 h. To understand the change of mechanical properties, in situ high energy X-ray diffraction (HEXRD) is used to examine the phase composition, load partitioning, slip system activity, and dislocation density evolution in all three specimens. The as-SLMed specimen is dominated by martensitic α'. After heat treatment, α' partly or fully decomposes into α+β, reducing the yield strength. In HT-730, beta precipitates with confined size show much higher lattice strain than the α'/α matrix during deformation; in HT-900, the lattice strain difference is mostly eliminated. This is a key reason for the increased ductility in HT-900. From the anisotropic lattice strain development, basal slip is identified as the easiest slip system in α'/α. Using an elasto-plastic self-consistent (EPSC) model, the critical resolved shear stress ratio between prismatic slip and basal slip (CRSS prism /CRSS basal ) is estimated to be 1.31 and 1.16 in the as -SLMed and the HT-900 specimens, respectively. Further, the alpha phase in HT-900 is able to activate multiple slip systems and accumulate more dislocations during plastic deformation. This explains why HT-900 has better ductility and higher work hardening rate than the other two specimens.

36 MATERIALS SCIENCE↗

Coupled effect of Cr and Al on interactions between a prismatic interstitial dislocation loop and an edge dislocation line in Fe-Cr-Al alloy

Segregation of alloying elements to a prismatic dislocation loop under irradiation is an important phenomenon in understanding the role of loops in radiation effects in alloys. In this work, various segregation sequences of Cr and Al atoms to a $\langle$100$\rangle$ and a 1/2 $\langle$111$\rangle$ prismatic dislocation loop in a Fe-Cr-Al alloy are explored using molecular dynamics method and ab initio energy calculation. Here, the results reveal that Cr can readily segregate to the loops while Al atoms cannot by themselves, but the segregated Cr atoms are able to promote Al segregation at the loops, defined as a coupled segregation of Cr and Al. After interacting with Cr and Al, a previously mobile 1/2 $\langle$111$\rangle$ loop becomes sessile. Al segregation through the coupled segregation process can further affect the pinning behavior of a dislocation loop to an edge dislocation motion. By varying the Al fraction in the segregated solutes, a nonlinear dependence of the pinning effect on dislocation motion is determined. At lower fractions, the pinning strength increases with the increasing Al fraction until Al fraction reaches a critical value of about 19%, above which the pinning strength decreases with further increase of Al fraction. All these results suggest that, in addition to the effect of Al on the surface resistance to oxidation, Al effect on the dislocation loop behavior is important to optimize the composition of Fe-Cr-Al alloys for their applications in accident tolerant fuel concepts.

36 MATERIALS SCIENCE↗

Novel Mechanisms for the Formation of Dislocation Cell Patterns in BCC Metal

In this study, we present the first simulation results of the formation of dislocation cell wall microstructures in tantalum subjected to shock loading. Dislocation patterns and cell wall formation are important to understanding the mechanical properties of the materials in which they spontaneously arise, and yet the processing and self-assembly mechanisms leading to their formation are poorly understood. By employing transmission electron microscopy and discrete dislocation dynamics, we propose a new mechanism involving coplanar dislocations and pseudo-dipole mixed dislocation arrays that is essential to the pattern formation process. Our large-scale 3D DDD simulations demonstrate the self-organization of dislocation networks into cell walls in deformed BCC metal (tantalum) persisting at strain ε = 20%. The simulation analysis captures several crucial aspects of how the dislocation cell pattern affects metal plasticity, as observed in experiments. Although experimental evidence is inconclusive regarding whether cell wall formation takes place at the shock front, after the shock, during release, or when the sample has had enough time to relax post-recovery, our simulations indicate cell wall formation occurs after the shock and before release. The extended Taylor hardening composite model effectively considers the non-uniform dislocation density when cell walls form and accurately describes the corresponding flow stress.

36 MATERIALS SCIENCE↗

Electronic descriptors for dislocation deformation behavior and intrinsic ductility in bcc high-entropy alloys

Controlling the balance between strength and damage tolerance in high-entropy alloys (HEAs) is central to their application as structural materials. Materials discovery efforts for HEAs are therefore impeded by an incomplete understanding of the chemical factors governing this balance. Through first-principles calculations, this study explores factors governing intrinsic ductility of a crucial subset of HEAs—those with a body-centered cubic (bcc) crystal structure. Analyses of three sets of bcc HEAs comprising nine different compositions reveal that alloy chemistry profoundly influences screw dislocation core structure, dislocation vibrational properties, and intrinsic ductility parameters derived from unstable stacking fault and surface energies. Key features in the electronic structure are identified that correlate with these properties: the fraction of occupied bonding states and bimodality of the d-orbital density of states. The findings enhance the fundamental understanding of the origins of intrinsic ductility and establish an electronic structure–based framework for computationally accelerated materials discovery and design.

36 MATERIALS SCIENCE↗

The effects of Cr particles addition on the aging behavior and mechanical properties of SiCp/7075Al composites

Highlights: • The novel investigated the effects of Cr particles on the aging behavior and mechanical properties of SiC{sub p}/7075Al composites. • The addition of Cr particles didn't change precipitation sequence, but significantly degraded precipitation kinetics of composites. • Cr particles had a significant effect on the tensile properties of the peak-aged composite because of Mg aggregation. - Abstract: The effects of Cr particles addition on the aging behavior and mechanical properties of SiC{sub p}/7075Al composites were systematically investigated. The results show that the precipitation sequence of (5 vol% Cr + 50 vol% SiC)/7075Al composites (C-7075Al) is still: GP zone → η′ → η (MgZn{sub 2}), but Cr particles degrade the precipitation kinetics of the C-7075Al composite in comparison to (5 vol% SiC{sub p} + 50 vol% SiC{sub p})/7075Al (B-7075Al) because of reduced dislocation density present in the matrix and higher thermal activation energy of the η′ phase. Besides, the addition of Cr particles has a significant effect on the mechanical properties of the C-7075Al composite during the aging process. In contrast to the as-cast state, the ultimate tensile strength of the C-7075Al composite obtains an increase of 120 MPa at the peak-aged period, significantly lower than those of 7075Al alloy (207 MPa) and the B-7075Al composite (151 MPa), which is attributable to the severe aggregation of elemental Mg at the interface between Cr particles and the Al matrix.

36 MATERIALS SCIENCE↗

Deconvoluting the Effect of Chromium and Aluminum on the Radiation Response of Wrought FeCrAl Alloys After Low-Dose Neutron Irradiation

FeCrAl alloys have been extensively investigated over the past decade as a candidate material for accident-tolerant fuel cladding in light water reactors. Here, we have completed a first of its kind study where Al and Cr concentrations are varied systematically under neutron irradiation to elucidate the post irradiation microstructural and mechanical response as a direct result of alloying content. Neutron irradiations were performed on alloys with composition Fe-(10-13)Cr-(5-7)Al in wt.% at temperatures of 214, 357, and 557°C to a dose of ~1.8 dpa (displacements per atom). Dislocation loop sizes and dispersion characteristics did not show strong compositional dependence. However, there were noticeable effects of composition on the dispersion of Cr-rich α'-precipitates, particularly a decrease in number density with increasing Al content or a decrease in Cr content. The present results confirm previous studies indicating the Cr concentration in these precipitates is lower than that expected in binary FeCr alloys and that Al can act as a destabilizing alloying element for the deleterious α'-phase.

36 MATERIALS SCIENCE↗

The effect of size and composition on the strength and hardening of Cu–Ni/Nb nanoscale metallic composites

Nanoscale metallic material composites consisting of bilayer and trilayer systems of two and three different metallic alternating layers show significant gains in hardness over monolithic single phase films. One of the main applications of these composites can be as protective coatings to technical components to increase their lifespan acting as a mechanical barrier to the carriers of permanent deformation. In this work, we study the strength of bilayer structures made of alternating layers of niobium (Nb) and copper–nickel (Cu–Ni) alloys. The effect of the layer size and composition on strength and hardening as well as the effect of the metal–alloy interface on the dislocation motion is investigated. The simulations reveal a close relationship between the atomic composition of the alloy and the hardening of the film. The results are also compared with experimental findings on nanopillars made of similar structures, and strong similarities are revealed and discussed.

36 MATERIALS SCIENCE↗

Multiscale Modeling of Inclusions and Precipitation Hardening in Metal Matrix Composites: Application to Advanced High-Strength Steels

In this study, the strengthening effect of inclusions and precipitates in metals is investigated within a multiscale approach that utilizes models at various length scales, namely, Molecular Mechanics (MM), discrete Dislocation Dynamics (DD), and an Eigenstrain Inclusion Method (EIM). Particularly, precipitates are modeled as hardsoft particles whose stress fields interact with dislocations. The stress field resulting from the elastic mismatch between the particles and the matrix is accounted for through the EIM. While the MM method is employed for the purpose of developing rules for DD for short range interaction between a single dislocation and an inclusion, the DD method is used to predict the strength of the composite resulting from the interaction between ensembles of dislocations and particles. As an application to this method, the mechanical behavior of Advanced High Strength Steel (AHSS) is investigated and the results are then compared to the experimental data. The results show that the finely dispersive precipitates can strengthen the material by pinning the dislocations up to a certain shear stress and retarding the recovery, as well as annihilation of dislocations. The DD results show that strengthening due to nano sized particles is a function of the density and size of the precipitates. This size effect is then explained using a mechanistic model developed based on dislocation-particle interaction.

Environmental Molecular Sciences Laboratory↗

Quantification of room temperature strengthening of laser shock peened Ni-based superalloy using synchrotron microdiffraction

Laser shock peening (LSP), a surface modification technique, is promising to enhance the strength and wear resistance for Ni-based superalloys. To understand the strengthening mechanism in a laser shock peened Ni-based superalloy DZ417G, we utilize synchrotron poly- and monochromatic X-ray microdiffraction, as well as electron microscopy and microhardness to quantify the local microstructures and mechanical properties at various depths. In the 1.2-mm-deep hardened layer, the microhardness increases monotonically by ~50% from the unaffected interior to the surface. Quantitative microdiffraction analysis shows that large amounts of dislocations are introduced by LSP. High densities of 7.1 × 10 15 m -2 and 11.8 × 10 15 m -2 are seen close to the peened surface for the γ- and γ'-phases, respectively, which are 5 and 20 times of those in the unaffected region. Different gradients of dislocation density are observed for the two phases from interior to surface, and their combined effect accounts well for the hardness increment. Due to the unaltered γ'-precipitates and chemical composition in the LSP affected zone, the large density of dislocations dominates the observed strengthening. Combined poly- and monochromatic X-ray microdiffraction allows quantifying the local microstructures of plastic deformation over a large sampling scale that can hardly be achieved using other materials characterization techniques.

36 MATERIALS SCIENCE↗

Influence of strain and dislocations on GaSb/GaAs quantum dots: From nested to staggered band alignment

We investigate the influence of strain and dislocations on band alignment in GaSb/GaAs quantum dot systems. Composition profiles from cross-sectional scanning tunneling microscopy images are interpolated onto a finite element mesh in order to calculate the distribution of local elastic strain, which is converted to a spatially varying band alignment using deformation potential theory. Our calculations predict that dislocation-induced strain relaxation and charging lead to significant local variations in band alignment. Furthermore, misfit strain induces a transition from a nested (type I) to a staggered (type II) band alignment. Although dislocation-induced strain relaxation prevents the type I to type II transition, electrostatic charging at dislocations induces the staggered band alignment once again.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Friction stir welding of multi-walled carbon nanotubes reinforced Al matrix composites

Highlights: • Al/MWCNT composites were successfully welded using friction stir welding. • After FSW, the composites possessed an excellent balance of mechanical properties. • High tensile strength and elongation over BM owing to MWCNTs after FSW. • Microstructures were investigated according to MWCNT contents and FSW conditions. - Abstract: In this study, we prepared composites between Al and multi-walled carbon nanotubes (MWCNTs) using the friction stir welding (FSW) method and investigated their microstructural evolution and mechanical properties by controlling the amount of MWCNT (1 and 3 vol%) and the plunging load (400 and 600 kg) used. After the FSW process, MWCNT showed slight coarsening of grain with random shear textures and accumulated dislocations; the differences obtained by varying the plunging load and MWCNT amount were insignificant. The friction-stir welded composite obtained using 3 vol% MWCNT and a plunging load of 600 kg possessed two-times better balance between strength and ductility than the base metal, due to the presence of both MWCNTs and the partially decomposed Al{sub 4}C{sub 3} in the composite.

36 MATERIALS SCIENCE↗

Extending Interfaces in 3D to Achieve Superior Nanoscale Strength in Ti/Nb Nanolaminates

Tuning the atomic-level structure of nanolaminates enables high strength, increased deformability, and the ability to absorb and mitigate damage due to varied crystalline defects, including dislocations. Here, we present the enhanced strength of Ti/Nb nanolaminates containing thick 3D interfaces (3DIs), relative to their chemically abrupt 2D counterparts. We examine the effects of crystallographic alignment and compositional gradients on mechanical behavior via experiments and phase-field-dislocation dynamics (PFDD) modeling. Mechanical testing reveals that nanolaminates containing thicker 3DIs demonstrate a 28% hardness enhancement compared with sharp-interface nanolaminates. PFDD modeling shows that the critical resolved shear stress (CRSS) increases with the 3DI thickness. Gradual compositional transitions in 3DIs were confirmed via scanning transmission electron microscopy and high-resolution transmission electron microscopy, showing sharp crystallographic transitions and a heightened interface topography. The findings establish a positive function between the 3DI thickness and mechanical robustness for hexagonal-closest-packed-containing composites, emphasizing the role of defect–interface interactions in tailoring the mechanical performance and providing a foundation for future interfacial engineering.

36 MATERIALS SCIENCE↗