Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “coils”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

A comparison of ASTROMAG coils made with aluminum and copper based superconductor

The use of an aluminum matrix superconductor in the coils for the ASTROMAG magnet will increase the integrated field for conducting particle astrophysics experiments in space as compared to equal mass coils made with a copper matrix superconductor. The increased ability to detect charged particles can be achieved without decreasing the current margin of the superconductor in the coils. The use of a low-resistivity aluminum matrix conductor increases the energy needed to initiate a quench by two orders or magnitude. The current decay time constant during a quench is substantially increased. As a result, the quench energy dumped into the helium tank is reduced (the ASTROMAG coils are thermally decoupled from the helium tank), and the forces on the shield and shells due to eddy currents will be lower. A description is also given of the problems associated with the use of an aluminum matrix superconductor in the coils.

Green, M. A.↗
NASA NTRS1992

Change in the coil distribution of electrodynamic suspension system

At the Miyazaki Maglev Test Center, the initial test runs were completed using a system design that required the superconducting coils to be parallel with the ground levitation coils. Recently, the coil distribution was changed to a system such that the two types of coils were perpendicular to each other. Further system changes will lead to the construction of a side wall levitation system. It is hoped that the development will culminate in a system whereby a superconducting coil will maintain all the functions: levitation, propulsion, and guidance.

Tanaka, Hisashi↗
NASA NTRS1996

Design Optimization for a Maglev System Employing Flux Eliminating Coils

Flux eliminating coils have received no little attention over the past thirty years as an alternative for realizing lift in a MAGLEV system. When the magnets on board the vehicle are displaced from the equilibrium or null flux point of these coils, they induce current in those coils which act to restore the coil to its null flux or centerline position. The question being addressed in this paper is that of how to choose the best coil for a given system. What appears at first glance to be an innocent question is in fact one that is actually quite involved, encompassing both the global economics and physics of the system. The real key in analyzing that question is to derive an optimization index or functional which represents the cost of the system subject to constraints, the primary constraint being that the vehicle lift itself at a certain threshold speed. Outlined in this paper is one scenario for realizing a total system design which uses sequential quadratic programming techniques.

Davey, Kent R.↗
NASA NTRS2005

Rod-Coil Block Polyimide Copolymers

This invention is a series of rod-coil block polyimide copolymers that are easy to fabricate into mechanically resilient films with acceptable ionic or protonic conductivity at a variety of temperatures. The copolymers consist of short-rigid polyimide rod segments alternating with polyether coil segments. The rods and coil segments can be linear, branched or mixtures of linear and branched segments. The highly incompatible rods and coil segments phase separate, providing nanoscale channels for ion conduction. The polyimide segments provide dimensional and mechanical stability and can be functionalized in a number of ways to provide specialized functions for a given application. These rod-coil black polyimide copolymers are particularly useful in the preparation of ion conductive membranes for use in the manufacture of fuel cells and lithium based polymer batteries.

Mary Ann B Meador↗
DOE OSTI2022

Coiled actuator system and method

A method of generating a coiled actuator fiber that includes twisting a fiber to generate a twisted fiber; wrapping the twisted fiber around a core yarn or fiber to generate a coil in the twisted fiber, which generates a coiled twisted fiber; setting the coiled twisted fiber by heat or chemical treatment; and removing at least a portion of the core yarn or fiber to generate a coiled actuator fiber.

Ridley, Brent↗
DOE OSTI2026

Test of Harmonic Coil Accuracy Using a Multi Vertex Probe

Magnets are integral components of particle accelerators, with different multipoles used to perform various beam conditioning functions, like steering and focusing. Testing accelerator magnets to ensure compliance with specification is a crucial step of fabrication. One of the most popular techniques for verifying magnetic field strength and integrity is the harmonic coil probe. Harmonic coil probes are comprised of passive loops that are rotated around the aperture of a magnet and are used to measure magnetic flux. Oftentimes the measurements of the harmonic coil probe are affected by transverse vibrations along the axis of rotation and torsional vibrations of the position closure sensor, both causing spurious harmonics. To make matters challenging, it is difficult to distinguish between the real harmonics of the magnet and the spurious harmonics during analysis. This research explores the use of a novel configuration of harmonic coil probe, Multi-Vertex Probe (MVP), to address multiple factors that affect the accuracy and repeatability of harmonic coil probe measurement. Most of the results are based on simulation data, in which artificial torsional distortions are introduced and removed with the proposed processing method. In addition to implementing torsional vibration removal in simulation, laboratory analysis regarding the source of vibrations was performed using a pre-fabricated MVP. More specifically, various mechanical conditions were used to explore the standard deviation of main harmonic’s flux amplitude. The conditions included: coupling type (rigid or soft), rotation speed, probe starting position within magnetic field, and cabling location inside the magnetic field. Along with this, the MVP’s measured noise floor in and outside a magnetic field was quantified.

Lofquist, Claire [Northern Illinois U.]↗
DOE OSTI2022

Wire-coil insert optimization for high-heat-load/flux synchrotron components

Many synchrotron components require high levels of internal-flow, forced-convection heat transfer to minimize surface temperatures, thermal gradients, and thermally induced stress on high-power beam-interacting surfaces. Wire-coil inserts, physically similar to a common spring, are mechanically fitted inside of component cooling passages to optimize heat transfer performance. They are routinely used in Advanced Photon Source (APS) front end and beamline high-heat-load/flux components to significantly enhance convection heat transfer-up to 400% compared to plain open passages. This has the additional benefit of greatly reducing coolant flow requirements for these components. Using several cooling passage sizes, five different wire sizes, and a range of pitch values, an experimental investigation conducted at the APS has determined the average heat transfer coefficient and resulting pressure loss as a function of water flow rate for 65 different wire-coil inserts. Data from this study have been non-dimensionalized and generalized to yield relationships that can be used to determine the heat transfer performance and resulting pressure loss for any given wire-coil insert that may be used at the APS. Through data reduction, the wire-coil insert characteristic dimensions have also been optimized to yield the highest heat transfer enhancement while minimizing the coolant flow requirements. These generalized expressions for wirecoil inserts will be presented, and they can be used by scientists and engineers during the component design process to evaluate achievable heat transfer performance and associated pressure loss, aiding in the establishment of optimized operating parameters and cooling passage flow distribution schemes.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Combined plasma–coil optimization algorithms

Combined plasma–coil optimization approaches for designing stellarators are discussed and a new method for calculating free-boundary equilibria for multiregion relaxed magnetohydrodynmics (MRxMHD) is proposed. Four distinct categories of stellarator optimization, two of which are novel approaches, are the fixed-boundary optimization, the generalized fixed-boundary optimization, the quasi-free-boundary optimization, and the free-boundary (coil) optimization. These are described using the MRxMHD energy functional, the Biot–Savart integral, the coil-penalty functional and the virtual casing integral and their derivatives. The proposed free-boundary equilibrium calculation differs from existing methods in how the boundary-value problem is posed, and for the new approach it seems that there is not an associated energy minimization principle because a non-symmetric functional arises. We propose to solve the weak formulation of this problem using a spectral-Galerkin method, and this will reduce the free-boundary equilibrium calculation to something comparable to a fixed-boundary calculation. In our discussion of combined plasma–coil optimization algorithms, we emphasize the importance of the stability matrix.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Pulse width dependence of magnetic field generation using laser-powered capacitor coils

Megagauss magnetic fields were generated by a current flowing through a U-shaped coil connecting two parallel copper foils. Two kJ-class lasers at various pulse widths from 2 ns to 9.9 ns passed through holes in the front foil and were focused on the back foil with an intensity of ~1.7×10 16 W/cm 2 . The coil current and resulting magnetic fields were characterized using ultrafast proton radiography, timed at the end of the laser pulses. Additionally, the measurements show that magnetic field strength decays with increasing laser pulse width. A lumped-circuit model was developed and showed consistency with the experimental measurements, demonstrating an ion shorting effect: as the ion current neutralizes the electron current contribution to interplate voltage, the coil current peaks on a timescale close to the ion transit time t i = d/v ion . FLASH simulations of the coil current are performed, and the calculated resistance values are used to constrain ion speed as a function of hot electron temperature.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Elastic-plastic conductor damage evaluation at over 0.4% strain using a high-stress REBCO coil

Abstract Recent reports on screening current stress simulations of high-field REBCO magnets frequently present peak stresses over 1 GPa. However, this result is probably an unrealistic artifact of purely elastic calculations, considering the macroscopic yield and fracture stresses of approximately 900 MPa and less than 1.1 GPa for Hastelloy substrate-coated conductors. Here, we evaluate elastic-plastic conductor damage at over 0.4% strain using a high-stress REBCO coil exposed to a high field to explore this elastic-plastic regime. The coil was located off-center in a low-temperature superconductor magnet so as to induce a significant screening current in the enhanced radial field. Voltage taps, a Hall sensor, and two strain gauges were used for the instrumentation. We obtained strains exceeding 0.4% near the outward edge during the coil current charge from 350 A to 390 A, where the coil was exposed to external axial and radial magnetic fields of 13 T and 0.5 T. Post mortem results showed wavy plastic deformation, electrical damage, and REBCO defects. An elastic-plastic simulation reproduced the measured strains and predicted that ∼1 GPa stress is sufficient to induce ∼0.9% strain, thus validating our initial concerns with purely elastic models. This paper provides our experimental and simulation results.

Bang, Jeseok (ORCID:0000000247616334)↗
DOE OSTI2022

Stellarator coil optimization supporting multiple magnetic configurations

Abstract We present a technique that can be used to design stellarators with a high degree of experimental flexibility. For our purposes, flexibility is defined by the range of values the rotational transform can take on the magnetic axis of the vacuum field while maintaining satisfactory quasisymmetry. We show that accounting for configuration flexibility during the modular coil design improves flexibility beyond that attained by previous methods. Careful placement of planar control coils and the incorporation of an integrability objective enhance the quasisymmetry and nested flux surface volume of each configuration. We show that it is possible to achieve flexibility, quasisymmetry, and nested flux surface volume to reasonable degrees with a relatively simple coil set through an NCSX-like example. This example coil design is optimized to achieve three rotational transform targets and nested flux surface volumes in each magnetic configuration larger than the NCSX design plasma volume. Our work suggests that there is a tradeoff between flexibility, quasisymmetry, and volume of nested flux surfaces.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Boundary condition effects on runaway electron mitigation coil modeling for the SPARC and DIII-D tokamaks

Abstract Extended-MHD modeling of planned Runaway Electron Mitigation Coils (REMC) for SPARC and DIII-D is performed with the NIMROD code. A coil has been designed for each machine, with the two differing in shape and location, but both having n = 1 symmetry (with n the toroidal mode number). Compared to previous modeling efforts, three improvements are made to the simulations boundary conditions. First a resistive wall model is used in place of an ideal wall. Second, the ThinCurr code is used to compute the time-dependent 3D fields used as magnetic boundary conditions for the simulations. Third, the simulation boundary is moved from the first-wall location to the Vacuum Vessel (VV), which extends the boundary past the location of the internal REMC. To remove the 3D coil from the simulation domain, an equivalent set of 3D fields is calculated at the VV boundary that produce approximately the same field distribution at the last closed flux surface assuming vacuum between the two. Each of these three boundary condition improvements leads to an improvement in the predicted performance of the REMC for both machines. The resistive wall alone primarily effects the resonance of the coil with the plasma after the TQ, affecting the q-profile evolution in the SPARC modeling, and allowing the applied spectrum to be modified in response to the plasma in the DIII-D modeling. The movement of the simulation boundary has the most significant effect on the RE confinement overall, including in the early stages, particularly for a DIII-D inner wall limited equilibrium, where the RE loss fraction increases from 90% to > 99%, with SPARC RE losses also occurring much earlier when the boundary is placed at the VV.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Capacitor Design for Self-Resonant Coils for Long-Distance Wireless Power Transfer System

In this paper, an integrated capacitor design is proposed for higher-order resonant tank topologies for self-resonant coils, such as series, parallel, LCC, LLC, etc. The capacitor is one of the large, lossy, and thermally vulnerable components of a high-frequency resonant tank, and designing a high-voltage, thermally stable resonant capacitor can be highly challenging. Designing the extremely high-voltage capacitor as an integral part of the coil reduces the size and complexity of the coil assembly. This paper proposes a low-loss PCB-based high-voltage capacitor design to achieve that target, which can be implemented as an integral part of the coil. The proposed capacitor designs are simulated using Multiphysics FEA and tested experimentally. A 23 kV, 133 pF capacitor prototype was built and tested as part of a 1 kW long-distance wireless charging system. The test results verify the capacitor’s voltage, current, and thermal resiliency performance.

Mohammad, Mostak [ORNL] (ORCID:0000000256388783)↗
DOE OSTI2020

Early-Time (E1) High-Altitude Electromagnetic Pulse Effects on Trip Coils

A High-Altitude Electromagnetic Pulse (HEMP) is a potential threat to the power grid. HEMP can couple to transmission lines and cables, causing significant overvoltages which can be harmful to line connected equipment. The effects of overvoltages on various types of power systems components need to be understood. HEMP effects on trip coils were tested and presented in this report. A high voltage pulser was built to replicate the induced voltage waveform from a HEMP. The pulser was used to test breaker trip coils with increasing pulse magnitudes ranging from 20 kV to 80 kV. The State-of-Health of each trip coils was measured via mechanical operation and impedance measurements before and after each insult to identify any damage or degradation to the trip coils. Dielectric breakdown was observed at the conductor leads during testing, causing the HEMP insult to be diverted to the grounded casing. However, the dielectric breakdown did not cause interference with regular device operation.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2023

Strain measurements of Nb₃Sn coils with optical fibers

The HL-LHC at CERN will be using new superconducting quadrupole magnets (MQXFA) made of Nb₃Sn that are in the process of being tested before installation in the LHC tunnel. MQXFA07 and MQXFA08 magnets failed because of high stress developed at the coil wedge/end spacer interface, where the Nb₃Sn coil, the stainless-steel end parts, and copper wedges exhibit different strain responses. Interrogating a cut piece of coil QXFP06 with optical fibers, we expect to get a better understanding of the stress response of the coil wedge/end spacer interface.

Nisa, Kuvvetn↗
DOE OSTI2024

Conceptual Design of A 20 T Dipole Based on Hybrid REBCO/Nb 3 Sn Cos-theta Coil

This paper presents a design concept of an HTS/LTS hybrid dipole with 50 mm aperture and 20 T nominal field based on a cos-theta coil and a cold iron yoke. The HTS part of magnet coil uses REBCO Twisted Stacked Tape cable. The LTS part is graded and made of two Nb3Sn Rutherford cables. Due to high sensitivity of HTS/LTS coils to large stresses and strains at high fields, a Stress Management (SM) concept combined with the cos-theta coil geometry is used. The results of magnet magnetic analysis are presented and discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Fermilab Automation of Coil Winding System

The automated coil winder project creates a repeatable, scalable method for producing superconducting magnet coils with increased accuracy and efficiency. The design uses an ortho cyclic winding method to achieve high fill factors by combining computer numerical control (CNC), microcontroller-based controls, and sophisticated optimization techniques. The method optimizes coil turns, core geometry, and current consumption by utilizing analytical models based on magnetic moment, Ohm’s law, and power constraints. For particle accelerator applications, prototype testing using a 3D-printed coil winder has shown enhanced winding repeatability, thermal management, and manufacturability.

Dzida, Rafal [Northern Illinois U.]↗
DOE OSTI2025

QXFA 167 Coil Fabrication Report

QXFA is a cosine theta coil used in the MQXFA, a Nb3Sn superconducting accelerator quadrupole magnet to be installed in the High-Luminosity LHC Interaction Regions. A series of MQXFA magnets is fabricated and tested by the US High-Luminosity LHC Accelerator Upgrade Project (AUP). This report details the fabrication process of the QXFA coil (QXFA 167) using Wind-and-React method, conducted from February 6 to March 20, 2025. The content covers coil winding, curing, and reaction, based on the travelers of FNAL as well as the observations and records by the author. The coil fabrication processes following heat reaction, including the impregnation process, are not covered in this report, as they were carried out after March 20.

43 PARTICLE ACCELERATORS↗