Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “classical compression”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Development of a Three-Dimensional PSE Code for Compressible Flows: Stability of Three-Dimensional Compressible Boundary Layers

A program is developed to investigate the linear stability of three-dimensional compressible boundary layer flows over bodies of revolutions. The problem is formulated as a two dimensional (2D) eigenvalue problem incorporating the meanflow variations in the normal and azimuthal directions. Normal mode solutions are sought in the whole plane rather than in a line normal to the wall as is done in the classical one dimensional (1D) stability theory. The stability characteristics of a supersonic boundary layer over a sharp cone with 50 half-angle at 2 degrees angle of attack is investigated. The 1D eigenvalue computations showed that the most amplified disturbances occur around x(sub 2) = 90 degrees and the azimuthal mode number for the most amplified disturbances range between m = -30 to -40. The frequencies of the most amplified waves are smaller in the middle region where the crossflow dominates the instability than the most amplified frequencies near the windward and leeward planes. The 2D eigenvalue computations showed that due to the variations in the azimuthal direction, the eigenmodes are clustered into isolated confined regions. For some eigenvalues, the eigenfunctions are clustered in two regions. Due to the nonparallel effect in the azimuthal direction, the eigenmodes are clustered into isolated confined regions. For some eigenvalues, the eigenfunctions are clustered in two regions. Due to the nonparallel effect in the azimuthal direction, the most amplified disturbances are shifted to 120 degrees compared to 90 degrees for the parallel theory. It is also observed that the nonparallel amplification rates are smaller than that is obtained from the parallel theory.

Balakumar, P.↗

Control-Relevant Modeling, Analysis, and Design for Scramjet-Powered Hypersonic Vehicles

Within this paper, control-relevant vehicle design concepts are examined using a widely used 3 DOF (plus flexibility) nonlinear model for the longitudinal dynamics of a generic carrot-shaped scramjet powered hypersonic vehicle. Trade studies associated with vehicle/engine parameters are examined. The impact of parameters on control-relevant static properties (e.g. level-flight trimmable region, trim controls, AOA, thrust margin) and dynamic properties (e.g. instability and right half plane zero associated with flight path angle) are examined. Specific parameters considered include: inlet height, diffuser area ratio, lower forebody compression ramp inclination angle, engine location, center of gravity, and mass. Vehicle optimizations is also examined. Both static and dynamic considerations are addressed. The gap-metric optimized vehicle is obtained to illustrate how this control-centric concept can be used to "reduce" scheduling requirements for the final control system. A classic inner-outer loop control architecture and methodology is used to shed light on how specific vehicle/engine design parameter selections impact control system design. In short, the work represents an important first step toward revealing fundamental tradeoffs and systematically treating control-relevant vehicle design.

Rodriguez, Armando A.↗

Thermo-viscoelastic analysis of composite materials, volume 1

Advanced composite materials, especially graphite/epoxy, are being applied to aircraft structures in order to improve performance and save weight. An important consideration in composite design is the residual strength of a structure containing holes, delaminations, or interlaminar damage when subjected to compressive loads. Recent studies have revealed the importance of viscoelastic effects in polymer-based composites. The viscoelastic effect is particularly significant at elevated temperature/moisture conditions since the matrix material is strongly affected by the environment. The solution of viscoelastic problems in composites was limited to special cases which can be solved by classical lamination theory. A finite element procedure is presented for calculating time-dependent stresses and strains in composite structures with general configurations and complicated boundary conditions. Using this procedure the in-plane and interlaminar stress distributions and histories in notched and unnotched composites were obtained for mechanical and thermal loads. Both two-dimensional and three-dimensional viscoelastic problems are analyzed. The effects of layup orientation and load spectrum on creep response and stress relaxation were also studied.

Lin, K. Y.↗

Comparison of pitch rate history effects on dynamic stall

Dynamic stall of an airfoil is a classic case of forced unsteady separated flow. Flow separation is brought about by large incidences introduced by the large amplitude unsteady pitching motion of an airfoil. One of the parameters that affects the dynamic stall process is the history of the unsteady motion. In addition, the problem is complicated by the effects of compressibility that rapidly appear over the airfoil even at low Mach numbers at moderately high angles of attack. Consequently, it is of interest to know the effects of pitch rate history on the dynamic stall process. This abstract compares the results of a flow visualization study of the problem with two different pitch rate histories, namely, oscillating airfoil motion and a linear change in the angle of attack due to a transient pitching motion.

Chandrasekhara, M. S.↗

The room-temperature shapes of four-layer unsymmetric cross-ply laminates

A geometrically nonlinear extension of classical lamination theory developed by Hyer (1981) for predicting the room-temperature shapes of unsymmetric laminates is reformulated using relaxed restrictions regarding the inplane strains. The inplane residual strains of unsymmetric laminates which have cooled from curing into a cylindrical room-temperature shape are examined numerically. Results show that the residual strains are compressive and practically independent of spatial location on the laminate. In addition, the room temperature shapes of the four-layer unsymmetric cross-ply laminates are predicted, and it is shown that the temperature shapes are a strong function of their size and their stacking arrangement. It is demonstrated that, depending on the parameters selected, the room-temperature shape of a four-layer cross-ply unsymmetric laminate can be a unique saddle shape, a unique cylindrical shape, or a cylindrical shape that can be snapped through to another cylindrical shape.

Hyer, M. W.↗

Design and analysis of filament-wound cylinders in compression

The objective of the study was to develop a more accurate model for the prediction of the compressive behavior of filament-wound composite cylindrical shells. Results from a closed-form analytical model and a three-dimensional finite element model show that the extensional and bending stiffness of the laminate is significantly reduced in tow cross-over regions and that bending-extension coupling is increased in comparison with classical lamination theory. The material properties predicted by a micromechanics analysis are included in a global finite element model of a filament-wound circular cylindrical shell which also incorporates variations in the laminate stacking thickness. Results from the global shell analysis are compared with experimental data.

Hipp, Patrick A.↗

Thermal response behavior of boundary-layer flows

This paper presents an approximate, but general, analysis for the thermal response behavior of incompressible, constant property, laminar boundary layer flow over a smooth object of arbitrary shape. It encompasses the classic time-dependent Leveque problem as its special case. Comparisons with available data show that, for fluids with Prandtl number of the order of unity or larger, this analytical solution is able to provide reasonably accurate results for most engineering applications. Under certain restrictive conditions, it can also be used to predict the thermal response of a compressible boundary layer flow.

Lin, F. N.↗

The Large Angle Spectroscopic Coronagraph (LASCO): Visible light coronal imaging and spectroscopy

The Large Angle Spectroscopic Coronagraph (LASCO) is a triple coronagraph being jointly developed for the Solar and Heliospheric Observatory (SOHO) mission. LASCO comprises three nested coronagraphs (C1, C2, and C3) that image the solar corona for 1.1 to 30 solar radii (C1: 1.1 to 3 solar radii, C2: 1.5 to 6 solar radii, and C3: 3 to 30.0 solar radii). The inner coronagraph (C1) is a newly developed mirror version of the classic Lyot coronagraph without an external occultor, while the middle coronagraph (C2) and the outer coronagraph (C3) are externally occulted instruments. High resolution coronal spectroscopy from 1.1 to 3 R solar radii can be performed by using a Fabry-Perot interferometer, which is part of C1. High volume memories and a high speed microprocessor enable extensive onboard image processing. Image compression by factors of 10 to 20 will result in the transmission of 10 to 20 full images per hour.

Brueckner, Guenter E.↗

CFD Analysis of an Installation Used to Measure the Skin-Friction Penalty of Acoustic Treatments

There is a drive to devise acoustic treatments with reduced skin-friction and therefore fuel-burn penalty for engine nacelles on commercial airplanes. The studies have been experimental, and the effects on skin-friction are deduced from measurements of the pressure drop along a duct. We conduct a detailed CFD analysis of the installation, for two purposes. The first is to predict the effects of the finite size of the rig, including its near-square cross-section and the moderate length of the treated patch; this introduces transient and blockage effects, which have not been included so far in the analysis. In addition, the flow is compressible, so that even with homogeneous surface conditions, it is not homogeneous in the streamwise direction. The second purpose is to extract an effective sand-grain roughness size for a particular liner, which in turn can be used in a CFD analysis of the aircraft, leading to actual predictions of the effect of acoustic treatments on fuel burn in service. The study is entirely based on classical turbulence models, with an appropriate modification for effective roughness effects, rather than directly modeling the liners.

Spalart, Philippe R.↗

Deformations of Flat Unsymmetric Laminates Subjected to Inplane Loads

The geometrically nonlinear deformation response of initially flat unsymmetric cross-ply laminates subjected to an inplane compressive load and two sets of boundary conditions is studied. Stability of the deformations is considered. At issue is whether or not the plate remains flat with increased compressive loading, and whether it buckles. A semi-infinite unsymmetric cross-ply laminate is used to show the combined effects of geometric nonlinearities and bending-stretch coupling. Finite element results for finite laminates are then presented, and it is shown that to a large degree the boundary conditions control the character of the deformation response. It appears that clamped boundary conditions support buckling behavior, in the classic sense of bifurcation, whereas simply-supported conditions do not.

Hyer, Michael W.↗

Velocity-coupled flow oscillations in a simulated solid-propellant rocket environment

A comprehensive numerical analysis has been carried out to study the unsteady flowfields in a simulated rocket-motor environment. The model is based on the time-dependent compressible Navier-Stokes equations with a two-equation turbulence closure scheme. Various important aspects of the coupling between acoustic oscillations and mean flowfields, including flow reversal, modification of transport properties, etc., are addressed. Results indicate that multi-dimensional effects play important roles in determining local flow structures and wave characteristics. In much of the domain, acoustic velocity nodal points are observed in the near-wall region. The classical one-dimensional theory fails to describe several important mechanisms associated with velocity-induced flow instabilities.

Yang, Vigor↗

Postbuckling response of long thick plates loaded in compression including higher order transverse shearing effects

This paper presents buckling and postbuckling results for compression-loaded simply-supported aluminum plates and composite plates with a symmetric lay-up of thin +/-45-deg plies composed of many layers. Buckling results for aluminum plates of finite length are given for various length-to-width ratios. Asymptotes to the curves based on the buckling results give N(XCr) for plates of infinite length. Postbuckling results for plates with transverse shearing flexibility are compared to results from classical theory for various width-to-thickness ratios. Characteristic curves indicating the average longitudinal direct stress resultant as a function of the applied displacements are calculated based on four different theories: classical von Karman theory using the Kirchhoff assumptions, first-order shear deformation theory, higher-order shear deformation theory, and three-dimensional flexibility theory. Present results indicate that the three-dimensional flexibility theory gives the lowest buckling loads. The higher-order shear deformation theory has fewer unknowns than the three-dimensional flexibility theory but does not take into account through-the-thickness effects. The figures presented show that small differences occur in the average longitudinal direct stress resultants from the four theories that are functions of applied end-shortening displacement.

Stein, Manuel↗

Variational Asymptotic Homogenization of Finitely Deformed Viscoelastic-Viscoplastic Composites

The objective of this paper is to develop a constitutive model for finitely deformed viscoelastic-viscoplastic materials and a micromechanics approach to homogenizing composites consisting of such materials. The development of the constitutive model involves establishing a thermodynamic framework based on finite strain theory, developing a viscoelasticity and a viscoplasticity model based on the thermodynamic framework, developing a radial return algorithm based on a classic framework, and deriving a closed-from incremental constitutive relation in the spatial configuration. The development of the micromechanics approach involves pulling-back the above constitutive relation to the material configuration, formulating a variational statement with the resulting constitutive relation, discretizing variational statement in a finite-dimensional space, and solving the discretized variational statement using an Euler–Newton predictor–corrector method. The constitutive model is calibrated via monotonic uniaxial compression tests on a polymer, and the calibrated model is validated by comparing its predictions with the cyclic test data. It is shown capable of characterizing viscoelasticity, viscoplasticity, and complex loading paths. The micromechanics approach’s capabilities are demonstrated through homogenizing a unidirectional fiber-reinforced composite, subjected to uniaxial, biaxial, and shear loading, at different strain rates. It is demonstrated to be capable of handling rate dependence and complex loading paths. The present framework can be further improved by implementing more sophisticated viscoelasticity and viscoplasticity models in future work.

Finite element analysis↗

Postbuckling response of long thick plates loaded in compression including higher order transverse shearing effects

Buckling and postbuckling results are presented for compression-loaded simply-supported aluminum plates and composite plates with a symmetric lay-up of thin + or - 45 deg plies composed of many layers. Buckling results for aluminum plates of finite length are given for various length-to-width ratios. Asymptotes to the curves based on buckling results give N(sub xcr) for plates of infinite length. Postbuckling results for plates with transverse shearing flexibility are compared to results from classical theory for various width-to-thickness ratios. Characteristic curves indicating the average longitudinal direct stress resultant as a function of the applied displacements are calculated based on four different theories: Classical von Karman theory using the Kirchoff assumptions, first-order shear deformation theory, higher-order shear deformation theory, and 3-D flexibility theory. Present results indicate that the 3-D flexibility theory gives the lowest buckling loads. The higher-order shear deformation theory has fewer unknowns than the 3-D flexibility theory but does not take into account through-the-thickness effects. The figures presented show that small differences occur in the average longitudinal direct stress resultants from the four theories that are functions of applied end-shortening displacement.

Stein, Manuel↗

Postbuckling analysis of shear deformable composite flat panels taking into account geometrical imperfections

The effects of initial geometrical imperfections on the postbuckling response of flat laminated composite panels to uniaxial and biaxial compressive loading are investigated analytically. The derivation of the mathematical model on the basis of first-order transverse shear deformation theory is outlined, and numerical results for perfect and imperfect, single-layer and three-layer square plates with free-free, clamped-clamped, or free-clamped edges are presented in graphs and briefly characterized. The present approach is shown to be more accurate than analyses based on the classical Kirchhoff plate model.

Librescu, L.↗

Development of Curved-Plate Elements for the Exact Buckling Analysis of Composite Plate Assemblies Including Transverse Shear Effects

The analytical formulation of curved-plate non-linear equilibrium equations that include transverse-shear-deformation effects is presented. A unified set of non-linear strains that contains terms from both physical and tensorial strain measures is used. Using several simplifying assumptions, linearized, stability equations are derived that describe the response of the plate just after bifurcation buckling occurs. These equations are then modified to allow the plate reference surface to be located a distance z(c), from the centroid surface which is convenient for modeling stiffened-plate assemblies. The implementation of the new theory into the VICONOPT buckling and vibration analysis and optimum design program code is described. Either classical plate theory (CPT) or first-order shear-deformation plate theory (SDPT) may be selected in VICONOPT. Comparisons of numerical results for several example problems with different loading states are made. Results from the new curved-plate analysis compare well with closed-form solution results and with results from known example problems in the literature. Finally, a design-optimization study of two different cylindrical shells subject to uniform axial compression is presented.

McGowan, David M.↗

Some Aeronautical Communications Experiments

Classically there has existed an asymmetry between the computing and communicating sides of aerospace systems. Over the past few decades, this asymmetry has shifted to favoring communication link technologies, meaning that advancements in available central processing units (CPUs), storage devices, and internal data buses have stagnated. Indeed, the increased emphasis placed on refining subsystem performance such as with antenna bandwidth in phased arrays, amplifier power efficiency, software defined radio (SDR) flexibility and encoding for data compression and error correction has given rise to successful debuts of multi-gigabit-per-second data return from long space-link distances. These accomplishments are easily quantifiable through link budgets and illustrate what is possible, but also reveal the deficiencies in overall communications capabilities. In particular, the ever-accelerating presence of aerospace vehicles gives rise to newer and larger classes of challenges to address the needs of 21st century systems. Furthermore remote sensing and imaging capabilities have far outpaced our ability to transmit their products to the ground, so we are increasingly dependent on pre-processing and downselection to contend with the communications bottleneck. No longer may we depend upon the constrained logistics in delivering end-to-end data delivery through manual reconfigurations, static event scheduling and execution on a per-vehicle basis, for these methods do not scale and therefore must give way to dynamic, networked approaches with an overall systems view in mind. Emerging mission requirements exhibit a trend toward multiple smaller-scale vehicles working together to perform dissimilar observations. Such operations necessitate sensor fusion across a constellation, and where data processing may be distributed throughout a fairly disconnected network whose topology changes over time in non-deterministic manners. Individual communications link performance is still very relevant to deploying an effective communications system, but now must be embedded within a greater architecture of capability to optimally utilize the bandwidth available from each link to generate an ultimate end-to-end quality of service. The deleterious effects of timing uncertainty across the arrangement presents a challenge to measurement synchronization and delivery, so a successful deployed system needs to be tolerant to the delays inherent in time-of-light between elements and digital processing latencies existing at each node. In this presentation we share the flight test results from a high performance Gbps laser communications terminal evaluated with a suite of store and forward capabilities called High-rate Delay Tolerant Networking (HDTN). The communications payload is operated over Lake Erie across a range of configurations including several convergence layers, and is evaluated to determine recovery time after link disruptions, information loss, efficiency and speed. The effectiveness of utilizing a flying laboratory to increase the Technology Readiness Level (TRL) of an integrated system in relevant environments is discussed, as well as the value of conducting aeronautics experiments to retire risk for technology infusion into space missions. Upcoming flight campaigns will be presented, including opportunities to demonstrate secure command and control, data intensive hyperspectral imaging, quantum link characterization, 4k High Definition (HD) video streaming and internetworked space-ground-aero relay operations. These experiments will pave the way for future missions which will depend upon interoperability across disparate government and privately owned networks, involve contention with uncertain and dynamic timing, and require agility to autonomously configure optimal parameters across networks of ever-increasing size and complexity to ensure data delivery. https://www1.grc.nasa.gov/space/scan/acs/tech-studies/dtn/

Daniel Raible↗

Colloids and Nucleation

The objectives of the work funded under this grant were to develop a microphotographic technique and use it to monitor the nucleation and growth of crystals of hard colloidal spheres. Special attention is given to the possible need for microgravity studies in future experiments. A number of persons have been involved in this work. A masters student, Keith Davis, began the project and developed a sheet illumination apparatus and an image processing system for detection and analysis. His work on a segmentation program for image processing was sufficient for his master's research and has been published. A post doctoral student Bernie Olivier and a graduate student Yueming He, who originally suggested the sheet illumination, were funded by another source but along with Keith made photographic series of several samples (that had been made by Keith Davis). Data extraction has been done by Keith, Bernie, Yueming and two undergraduates employed on the grant. Results are published in Langmuir. These results describe the sheet lighting technique as one which illuminates not only the Bragg scattering crystal, but all the crystals. Thus, accurate crystal counts can be made for nucleation rate measurements. The strange crystal length scale reduction, observed in small angle light scattering (SALS) studies, following the initial nucleation and growth period, has been observed directly. The Bragg scattering (and dark) crystal size decreases in the crossover region. This could be an effect due to gravitational forces or due to over- compression of the crystal during growth. Direct observations indicate a complex morphology for the resulting hard sphere crystals. The crystal edges are fairly sharp but the crystals have a large degree of internal structure. This structure is a result of (unstable) growth and not aggregation. As yet unpublished work compares growth exponents data with data obtained by SALS. The nucleation rate density is determined over a broad volume fraction range (0.505 to 0.575) and compared to classical nucleation rate calculations. The experimental nucleation rate density varies with volume fraction more slowly than expected theoretically. Gravity may influence nucleation because crystal nuclei are more dense than the surrounding fluid and may be gravitationally convected. The largest observed crystal size was near volume fraction 0.52. Near the freezing point, crystals should grow to large size because nuclei are sparse and there is plenty of room to grow without contacting other crystals. Near melting the opposite is true, with crystals growing into one another shortly after nucleation. The maximum crystal size seen near 0.52 volume fraction suggests that gravitational stresses are limiting crystal growth near freezing.

Ackerson, Bruce↗