Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ceramic processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Effects of temperature inversion on densification in chemical vapor infiltration

In a classical chemical vapor infiltration (CVI) process, the competing effects of chemical kinetics and reagent gas transport lead to non–uniform depositions such that outer layers of a preform densify faster leaving the core highly porous. Currently, CVI must be performed at a sufficiently low temperature to achieve good densification quality which leads to high processing time and cost. Volumetric heating of the preform, especially through microwaves, can create temperature inversion such that the core is hotter than the outer surface and potentially, overcome the challenges associated with isothermal CVI. Direct numerical simulations (DNS) of densification under various such temperature distributions indicate that microwave heating in CVI processing can lead to better (uniform) densification of porous preforms. Here the role of key parameters describing the temperature distributions on the densification behavior is investigated. Strategic temporal control of the temperature distribution shows that processing times can be reduced by almost half while maintaining a good densification quality similar to that of low–temperature isothermal processing. Inside–out densification due to the inverted temperature profile is a key distinguishing characteristic of microwave assisted CVI.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2017

Additive manufacturing and mechanical characterization of high density fully stabilized zirconia

Mechanical properties of additively manufactured 8 mol% yttria-stabilized zirconia (8YSZ) parts were extensively studied for the first time. A novel freeform extrusion fabrication process, called Ceramic On-Demand Extrusion (CODE), was employed to deposit an aqueous viscous suspension (~50 vol% solids loading) of fully stabilized zirconia powder in a layer-by-layer fashion. Each layer was exposed to infrared radiation after deposition to attain partial solidification due to drying. Before exposure, the layer was surrounded by oil to preclude non-uniform evaporation, which could cause warpage and crack formation. After the fabrication process was completed, the parts were humid-dried in an environmental chamber and densified by sintering under atmospheric pressure. Here standard test methods were employed to examine the properties of sintered parts including density, Vickers hardness, fracture toughness, Young's modulus, and flexural strength. Microstructural evaluation was also performed to observe the microstructural morphology and measure grain size. The results indicate that the properties of 8YSZ parts produced by the CODE process match those obtained by conventional fabrication techniques.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Comparing hydrothermal sintering and cold sintering process: Mechanisms, microstructure, kinetics and chemistry

In this study, we report the sintering of zinc oxide (ZnO) through the comparison between the hydrothermal sintering (HS) and the cold sintering process (CSP) operating in closed and open conditions, respectively. Sintering was performed at 155 ± 5 °C applying a pressure of 320 MPa, and during different holding times (0 min, 20 min, 40 min and 80 min). Whatever the low sintering process used, ceramics characteristics are almost similar in terms of relative densities and ZnO structure. However, several differences such as the nature of stabilized phases, grain sizes and quantities of residual molecules in the densified pellets, were characterized and explained. The formation of zinc acetate “bridges” was observed ex situ in hydrothermally sintered samples. Lastly, a detailed ReaxFF molecular dynamics simulation was performed to help understand the formation mechanisms of zinc acetate “bridges” and compare the chemical activities between HS and CSP.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Blue emission of Eu 2+ -doped translucent alumina

Inorganic scintillators are very important in medical and industrial measuring systems in the detection and measurement of ionizing radiation. In addition to Ce 3+ , a widely used dopant ion in oxide scintillators, divalent Europium (Eu 2+ ) has shown promise as a high-luminescence, fast-response luminescence center useful in the detection of ionizing radiation. In this research, aluminum oxide (Al 2 O 3 ) was studied as a host material for the divalent europium ion. Polycrystalline samples of Eu 2+ -doped translucent Al 2 O 3 were fabricated, and room temperature luminescence behavior was observed. Al 2 O 3 ceramics doped with 0.1 at% Eu 2+ were fabricated with a relative density of 99.75% theoretical density and in-line transmittance of 22% at a wavelength of 800 nm. The ceramics were processed by a gel-casting method, followed by sintering under high vacuum. The gelling agent, a copolymer of isobutylene and maleic anhydride, is marketed under the commercial name ISOBAM, and has the advantage of simultaneously acting as both a gelling agent and as a dispersant. The microstructure and composition of the vacuum-sintered Eu 2+ :Al 2 O 3 were characterized by Scanning Electric Microscopy (SEM), Transmission Electron Microscopy (TEM), and Energy-dispersive X-ray spectroscopy (EDS). The phase composition was determined by X-ray diffraction measurements (XRD) combined with Rietveld analysis. The photoluminescence behavior of the Eu 2+ :Al 2 O 3 was characterized using UV light as the excitation source, which emitted blue emission at 440 nm. The radio-luminescence of Eu 2+ :Al 2 O 3 was investigated by illumination with X-ray radiation, showing three emission bands at 376 nm, 575 nm and 698 nm. Furthermore, multiple level traps at different depths were detected in the Eu 2+ :Al 2 O 3 by employing thermoluminescence measurements.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Process for manufacturing SiC composite ceramics

A method is described for manufacturing a ceramic composite structure. The method includes wrapping ceramic fibers (22), such as SiC fibers, about the external surface of at least one form. The method further includes heating the wrapped fibers (22) to a temperature no greater than a first temperature, infiltrating voids (24) in the wrapped fibers (22) with the ceramic composite in a first vessel (12) at the first temperature, transferring the infiltrated wrapped fibers (22) from the first vessel (12) to a second vessel (14), distinct from the first vessel (12), and coating the infiltrated wrapped fibers (22) with the ceramic composite in the second vessel (14) at a second temperature, higher than the first temperature.

Lahoda, Edward J.↗
DOE OSTI2016

Effect of carbon impurity during the sintering of MOX fuels

UO{sub 2} and PuO{sub 2} powders are currently used as raw materials for the industrial fabrication of mixed uranium plutonium oxide (MOX) for light-water reactors. The mixture is pelletized before being sintered at 1700 Celsius degrees under a reducing atmosphere of Ar/4%H{sub 2} with 1200 vpm H{sub 2}O. At the end of the oxide ceramic sintering process, a swelling phenomenon sometimes occurs and could be responsible for the fuel non-compliance with safety specifications. This phenomenon is often caused by the presence of carbon impurities in the raw materials. In this paper, it will be shown how carbon impurities (naturally present or deliberately introduced) in the raw materials affect MOX fuel densification by sintering. For that purpose, MOX densification has been monitored by dilatometric measurements and the gases released during sintering have been continuously qualitatively and quantitatively analyzed. Gases released or trapped in the fuel during densification have been studied, as well as the sintered fuel characteristics (density, microstructure, U/Pu distribution). Results confirm that carbon impurities can play a major role in the fuel swelling: the oxides react with carbon and form gaseous CO molecules that could be trapped in the closed pores during sintering. This leads to a pressure increase within pores responsible for an irreversible swelling by creep deformation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

The Influence of Residual Copper Catalyst on the Polymer-to-Ceramic Conversion of a Click-Derived Polycarbosilane

Preceramic polymers (PCPs) are a key class of materials for the preparation of advanced ceramic components. Following conventional polymer processing and subsequent pyrolysis, polymer-derived ceramic (PDC) fibers, monoliths, and composites offer novel engineering opportunities for aerospace applications. Despite the rapidly emerging commercial applications of PDCs, many basic scientific questions remain regarding the structural transformation of the polymer to the final ceramic and how processing variables affect PDC materials properties. PCPs prepared using a mild and scalable copper (Cu) catalyzed azide/alkyne “click” reaction have been demonstrated as a unique class of material that can bind with transition metals, ultimately producing ultrahigh temperature ceramics (UHTCs) upon pyrolysis. Unexpectedly, it was found that the removal of residual Cu catalyst from a model click-derived polycarbosilane PCP significantly reduced the ceramic yield during pyrolysis. Herein, we report the influence of Cu impurities on polycarbosilane-derived SiC ceramics and present a mechanistic understanding of the unintended role of Cu in the polymer-to-ceramic conversion process. Synchrotron-based scattering and spectroscopy methods were implemented to track the evolution of different atomic species and local structures as well as the influence of Cu toward atomic-scale structures in the final ceramics. It was determined that Cu impurities catalyze the formation of silicon carbide through the formation of an intermediate molten copper/copper silicide, ultimately increasing the ceramic yield. Overall, this contribution highlights the need to carefully assess the interplay between the chemistries needed for PCP synthesis and their potential influence on final PDCs following processing.

Ponder, Jr., James F. [Air Force Research Laborato↗
DOE OSTI2015

Formation mechanism and characteristics of lanthanum-doped BaTiO{sub 3} powders and ceramics prepared by the sol–gel process

Pure and lanthanum-doped barium titanate nanopowders described by two different formulae, as Ba{sub 1−x}La{sub x}TiO{sub 3}, for lower La concentrations (0 ≤ x ≤ 0.005) and Ba{sub 1−x}La{sub x}Ti{sub 1−x/4}O{sub 3} for higher La concentration (x = 0.025) were prepared by an alkoxide sol–gel method. Single phase compositions were obtained after annealing at 900 °C for 2 h, in air. The increase of the lanthanum content causes structural and morphological changes in the oxide powders, including the evolution of the unit cell from tetragonal toward a cubic symmetry, the particle size decrease and a higher aggregation tendency. SEM investigations of the ceramics sintered at 1300 °C for 4 h indicate significant changes of the microstructural features (strong decrease of the average grain size and increase of the intergranular porosity) with the raise of La amount. Lanthanum addition to barium titanate prepared by sol–gel induces a more significant shift of the Curie temperature toward lower values, than that one reported in literature for ceramics of similar compositions, but processed by the conventional solid state method. The compositions with smaller La amount (x ≤ 0.005) show semiconducting properties at room temperature and high relative dielectric permittivity values, while the undoped ceramics and those doped with higher La content (x = 0.025) are good dielectrics. The ceramic with x = 0.025 exhibits acceptable low losses, a very diffuse ferroelectric–paraelectric transition and Curie temperature closed to the room temperature, being thus susceptible for high tunability applications. - Highlights: • Ba{sub 1−x}La{sub x}TiO{sub 3} (x ≤ 0.005) and Ba{sub 1−x}La{sub x}Ti{sub 1−x/4}O{sub 3} (x = 0.025) were prepared by sol–gel. • Ceramics with x < 0.5 exhibit semiconductor and high dielectric properties. • Ceramic with x = 0.025 exhibits acceptable low losses and diffuse phase transition.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Radiation damage of hollandite in multiphase ceramic waste forms

Radiation damage was simulated in multiphase titanate-based ceramic waste forms using an ion accelerator to generate high energy alpha particles (He + ) and an ion implanter to generate 7 MeV gold (Au 3+ ) particles. X-ray diffraction and transmission electron microscopy were used to characterize the damaged surfaces and nearby regions. Simulated multiphase ceramic waste forms were prepared using two processing methods: spark plasma sintering and melt-processing. Both processing methods produced ceramics with similar phase assemblages consisting of hollandite-, zirconolite/pyrochlore-, and perovskite- type phases. The measured heavy ion (Au 3+ ) penetration depth was less in spark plasma sintered samples than in melt-processed samples. Furthermore, structural breakdown of the hollandite phase occurred under He + irradiation indicated by the presence of x-ray diffraction peaks belonging to TiO 2 , BaTiO 5 , and other hollandite related phases (Ba 2 Ti 9 O 20 ). The composition of the constituent hollandite phase affected the extent of damage induced by Au 3+ ions.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D printing of ceramics: Advantages, challenges, applications, and perspectives

Abstract 3D printing (3DP) technologies have transformed the processing of advanced ceramics for small‐scale and custom designs during the past three decades. Simple and complex parts are designed and manufactured using 3DP technologies for structural, piezoelectric, and biomedical applications. Manufacturing simple or complex geometries or one‐of‐a‐kind components without part‐specific tooling saves significant time and creates new applications for advanced ceramic materials. Although development and innovations in 3DP of ceramics are far behind compared with metals or polymers, with the availability of different commercial machines in recent years for 3DP of ceramics, exponential growth is expected in this field in the coming decade. This article details various 3DP technologies for advanced ceramic materials, their advantages and challenges for manufacturing parts for various applications, and perspectives on future directions. We envision this work will be helpful to advanced ceramic researchers in industry and academia who are using different 3DP processes in the coming days.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Bioinspired nacre-like alumina with a bulk-metallic glass-forming alloy as a compliant phase

Bioinspired ceramics with micron-scale ceramic "bricks" bonded by a metallic "mortar" are projected to result in higher strength and toughness ceramics, but their processing is challenging as metals do not typically wet ceramics. To resolve this issue, we made alumina structures using rapid pressureless infiltration of a zirconium-based bulk-metallic glass mortar that reactively wets the surface of freeze-cast alumina preforms. The mechanical properties of the resulting Al 2 O 3 with a glass-forming compliant-phase change with infiltration temperature and ceramic content, leading to a trade-off between flexural strength (varying from 89 to 800 MPa) and fracture toughness (varying from 4 to more than 9 MPa·m ½ ). The high toughness levels are attributed to brick pull-out and crack deflection along the ceramic/metal interfaces. Since these mechanisms are enabled by interfacial failure rather than failure within the metallic mortar, the potential for optimizing these bioinspired materials for damage tolerance has still not been fully realized.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Glass-Ceramic Material Modeling

Glass-ceramics are a unique class of materials in which the growth of a ceramic phase(s) may be induced in an inorganic glass resulting in a microstructurally heterogeneous material with both glass and ceramic phases. This specialized processing is often referred to as "ceramming''. A wide variety of such materials have been developed through the use of different initial glass compositions and thermomechanical processing routes and that have enabled applications in dentistry, consumer kitchenware, and telescopes mirrors. These materials may also exhibit large apparent coefficients of thermal expansion making them attractive for consideration in glass-ceramic seals. These large apparent coefficients of thermal expansion often arise from silica polymorphs, such as cristobalite, undergoing a solid-to-solid phase transformations producing additional non-linearity in the effective material response.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Rare-earth doped transparent ceramics for spectral filtering and quantum information processing

Homogeneous linewidths below 10 kHz are reported for the first time in high-quality Eu{sup 3+} doped Y {sub 2}O{sub 3} transparent ceramics. This result is obtained on the {sup 7}F{sub 0}→{sup 5}D{sub 0} transition in Eu{sup 3+} doped Y {sub 2}O{sub 3} ceramics and corresponds to an improvement of nearly one order of magnitude compared to previously reported values in transparent ceramics. Furthermore, we observed spectral hole lifetimes of ∼15 min that are long enough to enable efficient optical pumping of the nuclear hyperfine levels. Additionally, different Eu{sup 3+} concentrations (up to 1.0%) were studied, resulting in an increase of up to a factor of three in the peak absorption coefficient. These results suggest that transparent ceramics can be useful in applications where narrow and deep spectral holes can be burned into highly absorbing lines, such as quantum information processing and spectral filtering.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Processing and properties of PSZT 95/5 ceramics with varying Ti and Nb substitution

Niobium doped lead-tin-zirconate-titanate ceramics near the PZT 95/5 orthorhombic AFE – rhombohedral FE morphotropic phase boundary Pb 1-0.5y (Zr 0.865-x Ti x Sn 0.135 ) 1-y Nb y O 3 were prepared according to a 2 2+1 factorial design with x = 0.05, 0.07 and y = 0.0155, 0.0195. The ceramics were prepared by a traditional solid-state synthesis route and sintered to near full density at 1250°C for 6 hours. All compositions were ~98% dense with no detectable secondary phases by XRD. The ceramics exhibited equiaxed grains with intergranular porosity and grain size was ~5 μm, decreasing with niobium substitution. Compositions exhibited remnant polarization values of ~32 μC/cm 2 , increasing with Ti substitution. Depolarization by the hydrostatic pressure induced FE-AFE phase transition was drastically affected by variation of the Ti and Nb substitution, increasing at a rate of 113 MPa / 1% Ti and 21 MPa / 1% Nb. Total depolarization output was insensitive to the change in Ti and Nb substitution, ~32.8 μC/cm 2 for the PSZT ceramics. The R3c-R3m and R3m-Pm3m phase transition temperatures on heating ranged from 90 to 105°C and 183 to 191°C, respectively. Ti substitution stabilized the R3c and R3m phases to higher temperatures, while Nb substitution stabilized the Pm3m phase to lower temperatures. Thermal hysteresis of the phase transitions was also observed in the ceramics, with transition temperature on cooling being as much as 10°C lower.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Controlling the sol–gel process of nano-crystalline lithium-mica glass-ceramic by its chemical composition and synthesis parameters

This paper aims to explore the impact of the parameters such as pH of the system, refluxing temperature, water quantity and chemical composition on the sol–gel synthesis of lithium-mica glass-ceramic nano-powder. The synthesis process was accomplished using two chemical composition formula (Li{sub (1+x)}Mg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6.5x}F{sub 2} and LiMg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6x}F{sub 2}). X-ray diffraction, Brunauer–Emmett–Teller surface area measurement and scanning electron microscopy techniques were applied to evaluate a variety of as-synthesized samples. Consequently, a transparent homogeneous sol was obtained under the conditions as pH ≤ 4, synthesis temperature ≤ 50 °C, and mol ratio of water to chemicals ≤ 2. The prepared nano-powders under such conditions were in the range of 60–100 nm. The results also revealed that the mica glass-ceramics prepared based on the composition Li{sub (1+x)}Mg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6.5x}F{sub 2} possessed finer powders due to their slow hydrolysis process. Moreover, any reduction in the stoichiometric deviation of lithium mica (x) leads to acquiring finer powders. - Highlights: • A transparent homogeneous sol leads to prepare nanopowders in the range of 60–100 nm. • The particles synthesized at lower temperatures possess finer sizes. • The acquired product which is prepared with excessive water offers larger sizes. • Any reduction in stoichiometric deviation leads to acquiring finer powders. • Taking synthesis composition as Li{sub (1+x)}Mg{sub 3}AlSi{sub 3(1+x)}O{sub 10+6.5x}F{sub 2} offers finer powders.

36 MATERIALS SCIENCE↗