Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “atmospheric pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Atmospheric Pressure Spray Chemical Vapor Deposited CuInS2 Thin Films for Photovoltaic Applications

Solar cells have been prepared using atmospheric pressure spray chemical vapor deposited CuInS2 absorbers. The CuInS2 films were deposited at 390 C using the single source precursor (PPh3)2CuIn(SEt)4 in an argon atmosphere. The absorber ranges in thickness from 0.75 - 1.0 micrometers, and exhibits a crystallographic gradient, with the leading edge having a (220) preferred orientation and the trailing edge having a (112) orientation. Schottky diodes prepared by thermal evaporation of aluminum contacts on to the CuInS2 yielded diodes for films that were annealed at 600 C. Solar cells were prepared using annealed films and had the (top down) composition of Al/ZnO/CdS/CuInS2/Mo/Glass. The Jsc, Voc, FF and (eta) were 6.46 mA per square centimeter, 307 mV, 24% and 0.35%, respectively for the best small area cells under simulated AM0 illumination.

Harris, J. D.↗
NASA NTRS2007

Atmospheric Pressure Effects on Cryogenic Storage Tank Boil-Off

The Cryogenics Test Laboratory (CTL) at the Kennedy Space Center (KSC) routinely utilizes cryostat test hardware to evaluate comparative and absolute thermal conductivities of a wide array of insulation systems. The test method is based on measurement of the flow rate of gas evolved due to evaporative boil-off of a cryogenic liquid. The gas flow rate typically stabilizes after a period of a couple of hours to a couple of days, depending upon the test setup. The stable flow rate value is then used to calculate the thermal conductivity for the insulation system being tested. The latest set of identical cryostats, 1,000-L spherical tanks, exhibited different behavior. On a macro level, the flow rate did stabilize after a couple of days; however the stable flow rate was oscillatory with peak to peak amplitude of up to 25 percent of the nominal value. The period of the oscillation was consistently 12 hours. The source of the oscillation has been traced to variations in atmospheric pressure due to atmospheric tides similar to oceanic tides. This paper will present analysis of this phenomenon, including a calculation that explains why other cryostats are not affected by it.

Sass, J. P.↗
DOE OSTI2022

Improved uranium isotopic ratio determinations for the liquid sampling-atmospheric pressure glow discharge orbitrap mass spectrometer by use of moving average processing

The liquid sampling-atmospheric pressure glow discharge (LS-APGD) is a versatile combined atomic and molecular (CAM) ionization source capable of ionizing elemental species, small polar compounds, low-polarity polycyclic aromatic hydrocarbons, and proteins. While the LS-APGD has been proven capable of determining the 235U/238U isotope ratio in enriched and natural uranium, recent efforts have strived to reduce the analysis time of individual measurements by employing higher-order data processing techniques, specifically, moving average methods. Additionally, the use of a moving average (of data windows of various widths) improves the precision of the ratio measurements and reduces the number of scans needed to be collected to generate high-precision results. Additionally, use of the moving average minimizes the quantity of sample that needs to be analyzed while reducing the measurement time. These reductions have allowed isotope ratio (IR) determinations to be made using injections instead of direct infusion of the analyte. For example, employing a 40-point window width in the moving average to direct infusion data reduced the percent relative standard deviation (% RSD) of the 235U/238U values from 3.4% to 0.5%. For the injection of a 100 μL aliquot, the % RSD was reduced from 5.3% to 0.7%.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2023

Influence of liquid conductance on the temporal evolution of self-organization patterns in atmospheric pressure DC glow discharges

Abstract Self-Organized Patterns (SOPs) at plasma-liquid interface in atmospheric pressure plasma discharges refer to the formation of intricate and puzzling structures due to the interplay of electrodynamic and hydrodynamic processes. Studies conducted to date have shown that this phenomenon results in the formation of distinctive patterns such as circular ring, star, gear, dots, spikes, etc., and primarily depends on working gas, electrolyte type, gap distance, current, conductivity, etc. However, an adequate understanding of how these patterns change from one type to another is still not available. This study aims to elucidate the influence of initial liquid conductance ( σ i ) on the temporal evolution of SOPs in liquid-anode discharges. The discharge was generated in a pin-to-liquid anode configuration at a constant helium (He) flow rate of 500 sccm and DC applied voltage of 6 kV at a gap distance of 12 mm. Through the gradual increment of σ i from 1.8 μ S to 4820 μ S, we observe that the trend in the evolution of SOPS takes place as solid discs, spikes, dots, rings, double rings, and stars. The continuous formation of reactive species onto the liquid anode in all conductive solutions results in a decrease in pH, an increase in bulk liquid temperature, and an increase in total dissolved solutes, and these have been confirmed through experimental measurements. Observations using optical emission spectroscopy show that the electrons at the plasma-liquid interface participate in the reduction of cations followed by their excitation & ionization due to which electron density as well as emissions from excited species (mainly hydroxyl radicals & excited nitrogen) decrease with time. Our investigation provides experimental evidence on the presence of cations at the plasma-liquid interface required for SOP formation.

Physics↗
DOE OSTI2022

Manufacture of Carbon Foam in Continuous Process at Atmospheric Pressure

The objective is to develop continuous processing of carbon foam products made from coal at atmospheric pressure. Both carbon foam panels and lightweight carbon foam aggregates have been developed. A successful outcome would: 1) significantly reduce the cost to manufacture carbon foam through reductions in capital and labor costs, 2) significantly reduce the manufacturing time from weeks to hours, and 3) enable the manufacture of much larger volumes of carbon foam. All of these features are expected to enable carbon foam to enter much larger markets and create meaningful demand for U.S. coal.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS2002

Atmospheric pressure chemical ionization studies of non-polar isomeric hydrocarbons using ion mobility spectrometry and mass spectrometry with different ionization techniques

The ionization pathways were determined for sets of isomeric non-polar hydrocarbons (structural isomers, cis/trans isomers) using ion mobility spectrometry and mass spectrometry with different techniques of atmospheric pressure chemical ionization to assess the influence of structural features on ion formation. Depending on the structural features, different ions were observed using mass spectrometry. Unsaturated hydrocarbons formed mostly [M - 1]+ and [(M - 1)2H]+ ions while mainly [M - 3]+ and [(M - 3)H2O]+ ions were found for saturated cis/trans isomers using photoionization and 63Ni ionization. These ionization methods and corona discharge ionization were used for ion mobility measurements of these compounds. Different ions were detected for compounds with different structural features. 63Ni ionization and photoionization provide comparable ions for every set of isomers. The product ions formed can be clearly attributed to the structures identified. However, differences in relative abundance of product ions were found. Although corona discharge ionization permits the most sensitive detection of non-polar hydrocarbons, the spectra detected are complex and differ from those obtained with 63Ni ionization and photoionization. c. 2002 American Society for Mass Spectrometry.

Non-NASA Center↗
NASA NTRS1998

Soot Formation in Laminar Premixed Methane/Oxygen Flames at Atmospheric Pressure

Flame structure and soot formation were studied within soot-containing laminar premixed mc1hane/oxygen flames at atmospheric pressure. The following measurements were made: soot volume fractions by laser extinction, soot temperatures by multiline emission, gas temperatures (where soot was absent) by corrected fine-wire thermocouples, soot structure by thermophoretic sampling and transmission electron microscope (TEM), major gas species concentrations by sampling and gas chromatography, and gas velocities by laser velocimetry. Present measurements of gas species concentrations were in reasonably good agreement with earlier measurements due to Ramer et al. as well as predictions based on the detailed mechanisms of Frenklach and co-workers and Leung and Lindstedt: the predictions also suggest that H atom concentrations are in local thermodynamic equilibrium throughout the soot formation region. Using this information, it was found that measured soot surface growth rates could be correlated successfully by predictions based on the hydrogen-abstraction/carbon-addition (HACA) mechanisms of both Frenklach and co-workers and Colket and Hall, extending an earlier assessment of these mechanisms for premixed ethylene/air flames to conditions having larger H/C ratios and acetylene concentrations. Measured primary soot particle nucleation rates were somewhat lower than the earlier observations for laminar premixed ethylene/air flames and were significantly lower than corresponding rates in laminar diffusion flames. for reasons that still must be explained.

Xu, F.↗
NASA NTRS2001

Soot Formation in Laminar Premixed Methane/Oxygen Flames at Atmospheric Pressure

Flame structure and soot formation were studied within soot-containing laminar premixed methanefoxygen flames at atmospheric pressure. The following measurements were made: soot volume fractions by laser extinction, soot temperatures by multiline emission, gas temperatures (where soot was absent) by corrected fine-wire thermocouples, soot structure by thermophoretic sampling and transmission electron microscope (TEM), major gas species concentrations by sampling and gas chromatography, and gas velocities by laser velocimetry. Present measurements of gas species concentrations were in reasonably good agreement with earlier measurements due to Ramer et al. as well as predictions based on the detailed mechanisms of Frenklach and co-workers and Leung and Lindstedt; the predictions also suggest that H atom concentrations are in local thermodynamic equilibrium throughout the soot formation region. Using this information, it was found that measured soot surface growth rates could be correlated successfully by predictions based on the hydrogenabstraction/carbon-addition (HACA) mechanisms of both Frenklach and co-workers and Colket and Hall, extending an earlier assessment of these mechanisms for premixed ethylene/air flames to conditions having larger H/C ratios and acetylene concentrations. Measured primary soot particle nucleation rates were somewhat lower than the earlier observations for laminar premixed ethylene/air flames and were significantly lower than corresponding rates in laminar diffusion flames, for reasons that still must be explained.

Xu, F.↗
NASA NTRS1954

Explosion and combustion properties of alkylsilanes I : temperature-composition limits of explosion for methyl-,dimethyl-,trimethyl-,tetramethyl-,and vinylsilane at atmospheric pressure

The explosion limits of five alkylsilanes were determined as a function of temperature and composition at a pressure of 1 atmosphere. Over a fuel concentration range of 2 to 10 percent, the lowest temperatures (zero C) below which explosion did not occur for the five fuels studied were: tetramethylsilane (CHsub3)sub4Si, 450 degrees; trimethlysilane (CHsub3)sub3SiH, 310 degrees;dimethylsilane (CHsub3)sub2SiHsub2, 220 degrees; methylsilane CHsub3SiHsub3, 130 degrees; and vinylsilane Hsub2C=CH-SiHsub3, 90 degrees. Explosion limits for hydrocarbons analogous to these silanes fall in a temperature range of 500 degrees to 600 degrees C. Since the explosion temperatures of the alkylsilanes are lower than those of the hydrocarbons and since they decrease as hydrogen atoms are substituted for methyl groups, it was concluded that the Si-H bond is more readily susceptible to oxidation than the C-H bond.

Schalla, Rose L↗
DOE OSTI2021

Particle emission with identification from an atmospheric pressure plasma liquid interface

A conspicuous emission phenomenon of luminous particles from the liquid anode surface of an atmospheric pressure DC glow discharge is reported. The emission has been shown to occur when the plasma forms a pattern on the surface of the liquid electrolyte. Here, the spatial-temporal evolutions of the trajectories of emitted particles were studied using a high-speed imaging system. Particles were sampled in flight using a witness plate for analysis. Critical particle characteristics were examined using electron microscope technologies. The morphology of the resulting splats and compositions suggest that they are molten droplets with a great deal of structure, including evidence of nanoprecipitation. A theoretical model was employed to estimate the particle size from the measured splats, which provides a radius range within a hundred micrometers. This experiment leads to the postulation of a mechanism in which particle emission at the plasma liquid interface is likely driven by the Taylor cone effect.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2005

Bacillus subtilis spore survival and expression of germination-induced bioluminescence after prolonged incubation under simulated Mars atmospheric pressure and composition: implications for planetary protection and lithopanspermia

Bacterial endospores in the genus Bacillus are considered good models for studying interplanetary transfer of microbes by natural or human processes. Although spore survival during transfer itself has been the subject of considerable study, the fate of spores in extraterrestrial environments has received less attention. In this report we subjected spores of a strain of Bacillus subtilis, containing luciferase resulting from expression of an sspB-luxAB gene fusion, to simulated martian atmospheric pressure (7-18 mbar) and composition (100% CO(2)) for up to 19 days in a Mars simulation chamber. We report here that survival was similar between spores exposed to Earth conditions and spores exposed up to 19 days to simulated martian conditions. However, germination-induced bioluminescence was lower in spores exposed to simulated martian atmosphere, which suggests sublethal impairment of some endogenous spore germination processes.

Mars↗
DOE OSTI2022

Plasma‐driven biocatalysis: In situ hydrogen peroxide production with an atmospheric pressure plasma jet increases the performance of OleT JE when compared to adding the same molar amount of hydrogen peroxide in bolus

Abstract Enzymes like fatty acid peroxygenase OleT JE are desirable enzymes for the industry. While they require inexpensive hydrogen peroxide for activity, the same hydrogen peroxide also causes overoxidation of their reactive heme center. Here, we generate hydrogen peroxide slowly in situ using the Cooperation in Science and Technology (COST)‐Jet, an atmospheric pressure plasma jet, to avoid overoxidizing OleT JE . The COST‐Jet was operated in helium with a water admixture to provide hydrogen peroxide for OleT JE activity. This helium/water admixture produced the highest enzyme turnover numbers after 2 min of treatment. These turnover numbers were even superior to using an equimolar amount of hydrogen peroxide to treat the enzymes exogenously, showing that this plasma source can provide a reliable amount of reaction mediator to support OleT JE activity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

High Performance GaAs Solar Cells Grown at High Growth Rates by Atmospheric-Pressure Dynamic Hydride Vapor Phase Epitaxy

We report GaAs solar cells grown at rates exceeding 300 um/h by atmospheric-pressure dynamic hydride vapor phase epitaxy (D-HVPE). The surface morphology of the GaAs layers grown at those rates is smooth, with root mean square surface roughness of < 1.4 nm. We grew GaAs solar cells at rates from 35 - 309 um/h with negligible degradation in open circuit voltages (VOC), which ranged from 1.04 - 1.07 V. We showed the slight decrease in VOC is due to lack of doping optimization at higher growth rates. Deep level transient spectroscopy measurements showed low point defect densities that increases slightly with growth rate from 35 - 309 um/h. The low point defect concentrations and the high VOCs indicate that high material quality can be maintained at these extremely high growth rates, enabling the deposition of high efficiency cells in mere seconds instead of hours.

14 SOLAR ENERGY↗
NASA NTRS2007

Spacecraft Sterilization Using Non-Equilibrium Atmospheric Pressure Plasma

As a solution to chemically and thermally destructive sterilization methods currently used for spacecraft, non-equilibrium atmospheric pressure plasmas are used to treat surfaces inoculated with Bacillus subtilis and Deinococcus radiodurans. Evidence of significant morphological changes and reduction in viability due to plasma exposure will be presented, including a 4-log reduction of B. subtilis after 2 minutes of dielectric barrier discharge treatment.

disinfection↗
DOE OSTI2023

Continuous Processing of Carbon Foam Products Made from Coal at Atmospheric Pressure

The main goal of the project was to create a continuous manufacturing process for carbon foam that operates at atmospheric pressure and can generate well-formed carbon foam panels and lightweight aggregates. This objective was accomplished and has enabled a platform where carbon foam products can be manufactured at significantly reduced cost and cycle time relative to the conventional high-pressure batch process, which in turn can enable the manufacture of much larger volumes of carbon foam. All these features should enable carbon foam to enter much larger markets and create meaningful demand for U.S. coal. Carbon foam panels and aggregate both consisted of at least 70 weight percent carbon per program requirements (typical was over 90-wt%), and at least 51 weight percent of the carbon was to be coal derived (typical was over 90-wt% carbon was from coal). Analyses regarding life cycle, technoeconomics, and final technological gaps have been documented in separate reports. This final report documents the methods used to attain the main goal and describes the technical results.

01 COAL, LIGNITE, AND PEAT↗
NASA NTRS1986

Measurement of viscosity of gaseous mixtures at atmospheric pressure

Coefficients of viscosity of various types of gas mixtures, including simulated natural-gas samples, have been measured at atmospheric pressure and room temperature using a modified capillary tube method. Pressure drops across the straight capillary tube section of a thermal mass flowmeter were measured for small, well-defined, volume flow rates for the test gases and for standard air. In this configuration, the flowmeter provides the volumetric flow rates as well as a well-characterized capillary section for differential pressure measurements across it. The coefficients of viscosity of the test gases were calculated using the reported value of 185.6 micro P for the viscosity of air. The coefficients of viscosity for the test mixtures were also calculated using Wilke's approximation of the Chapman-Enskog (C-E) theory. The experimental and calculated values for binary mixtures are in agreement within the reported accuracy of Wilke's approximation of the C-E theory. However, the agreement for multicomponent mixtures is less satisfactory, possible because of the limitations of Wilkes's approximation of the classical dilute-gas state model.

Singh, J. J.↗
NASA NTRS2012

Simulation Tool for Dielectric Barrier Discharge Plasma Actuators at Atmospheric and Sub-Atmospheric Pressures: SBIR Phase I Final Report

This report is the final report of a SBIR Phase I project. It is identical to the final report submitted, after some proprietary information of administrative nature has been removed. The development of a numerical simulation tool for dielectric barrier discharge (DBD) plasma actuator is reported. The objectives of the project were to analyze and predict DBD operation at wide range of ambient gas pressures. It overcomes the limitations of traditional DBD codes which are limited to low-speed applications and have weak prediction capabilities. The software tool allows DBD actuator analysis and prediction for subsonic to hypersonic flow regime. The simulation tool is based on the VORPAL code developed by Tech-X Corporation. VORPAL's capability of modeling DBD plasma actuator at low pressures (0.1 to 10 torr) using kinetic plasma modeling approach, and at moderate to atmospheric pressures (1 to 10 atm) using hydrodynamic plasma modeling approach, were demonstrated. In addition, results of experiments with pulsed+bias DBD configuration that were performed for validation purposes are reported.

Likhanskii, Alexandre↗
NASA NTRS1994

Detection of atmospheric pressure loading using very long baseline interferometry measurements

Loading of the Earth by the temporal redistribution of global atmospheric mass is likely to displace the positions of geodetic monuments by tens of millimeters both vertically and horizontally. Estimates of these displacements are determined by convolving National Meteorological Center (NMC) global values of atmospheric surface pressure with Farrell's elastic Green's functions. An analysis of the distances between radio telescopes determined by very long baseline interferometry (VLBI) between 1984 and 1992 reveals that in many of the cases studied there is a significant contribution to baseline length change due to atmospheric pressure loading. Our analysis covers intersite distances of between 1000 and 10,000 km and is restricted to those baselines measured more than 100 times. Accounting for the load effects (after first removing a best fit slope) reduces the weighted root-mean-square (WRMS) scatter of the baseline length residuals on 11 of the 22 baselines investigated. The slight degradation observed in the WRMS scatter on the remaining baselines is largely consistent with the expected statistical fluctuations when a small correction is applied to a data set having a much larger random noise. The results from all baselines are consistent with approximately 60% of the computed pressure contribution being present in the VLBI length determinations. Site dependent coefficients determined by fitting local pressure to the theoretical radial displacement are found to reproduce the deformation caused by the regional pressure to within 25% for most inland sites. The coefficients are less reliable at near coastal and island stations.

Vandam, T. M.↗