Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ambient temperature”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Coexistence of vitreous and crystalline phases of H 2 O at ambient temperature

Formation of vitreous ice during rapid compression of water at room temperature is important for biology and the study of biological systems. Here, we show that Raman spectra of rapidly compressed water at greater than 1 GPa at room temperature exhibits the signature of high-density amorphous ice, whereas the X-ray diffraction (XRD) pattern is dominated by crystalline ice VI. To resolve this apparent contradiction, we used molecular dynamics simulations to calculate full vibrational spectra and diffraction patterns of mixtures of vitreous ice and ice VI, including embedded interfaces between the two phases. We show quantitatively that Raman spectra, which probe the local polarizability with respect to atomic displacements, are dominated by the vitreous phase, whereas a small amount of the crystalline component is readily apparent by XRD. The results of our combined experimental and theoretical studies have implications for detecting vitreous phases of water, survival of biological systems under extreme conditions, and biological imaging. The results provide additional insight into the stable and metastable phases of H 2 O as a function of pressure and temperature, as well as of other materials undergoing pressure-induced amorphization and other metastable transitions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Ambient Temperature Sodium Polysulfide Catholyte for Nonaqueous Redox Flow Batteries

This study reports a sodium polysulfide catholyte for nonaqueous redox flow batteries (RFBs). We demonstrate reversible capacities up to 200 mAh/gS with negligible fade over 250 cycles at room temperature for sodium polysulfide|biphenyl full cells containing Na + ß '' -Al 2 O 3 solid electrolyte (BASE) membranes. Interestingly, formation of insoluble S and Na 2 S 4 phases did not inhibit the catholyte's cycle life which is likely due to the low concentrations used in the lab-scale prototypes. 3-electrode galvanostatic AC impedance measurements demonstrate that voltage losses were dominated by charge transfer at the cathode, and relevant kinetic parameters (i.e., transfer coefficients and exchange current density) were calculated through a Tafel analysis. To the best of our knowledge, this is the first report applying such an impedance approach to nonaqueous RFBs. Overall, the use of low-cost active materials makes sodium polysulfide|biphenyl RFBs promising for long duration energy storage applications. Furthermore, if strategies are developed to increase the solubility of S and/or low order polysulfides (Na 2 S x , x ≤ 4), specific energies up to 100 Wh kg -1 (including combined mass of the anolyte and catholyte) can be achieved.

25 ENERGY STORAGE↗

Low temperature, ambient pressure electrochemical ammonia synthesis in alkaline media — Mechanistic studies and catalyst design. Final Report

Ammonia synthesis via the Haber-Bosch process is a pillar of modern agriculture, which converts the abundant but inert dinitrogen in the atmosphere to nitrogen-based fertilizers. Despite more than a century of optimization, the Haber-Bosch process remains energy intensive and reliant on fossil fuels and produces large amounts of CO 2 . Distributed and modular ammonia synthesis via the electrochemical nitrogen reduction reaction (ENRR) at or close to ambient conditions, powered by renewable electricity is an attractive alternative because it allows as needed production of ammonia, and in turn fertilizers. However, selective ENRR catalysts remain lacking. In this project, we systematically investigated two categories of catalytic materials, i.e., precious metals and transition metal nitrides, in the ENRR. Precious metals exhibit low activity and selectivity in the ENRR, which is in agreement with recent computational studies. Transition metal nitrides, especially VN, has been demonstrated as active and selective ENRR catalysts. We developed the first quantitative method to determine the amount of ammonia produced in the ENRR on N-containing containing catalysts in the membrane electrode assembly configuration. An initial ammonia production rate of 6.6 × 10 -10 mol s -1 mg -1 and a Faradaic efficiency of 6.0% at -0.1 V were reached on VN. After the initial deactivation, VN was shown to be stable in the ENRR for 116 hours with a steady state ammonia production rate of 1.1 × 10 -10 mol s -1 cm -2 . A vanadium oxynitride species was identified as the active phase in the ENRR via a combination of operando and ex situ characterization techniques. In addition, we established that the ENRR proceeded on transition metal nitrides via the Mars van Krevelen mechanism and determined the initial and steady state active site densities by developing a quantitative isotopic exchange method.

42 ENGINEERING↗

Site Ambient Temperatures and Operating Schedules for EIC - Utility CW Considerations

The heat dissipated by the EIC accelerator system and components is ultimately removed by the conventional water-cooling systems that will be ultimately dissipated the waste heat to the atmosphere. An estimated 45 MW of heat will be dissipated to water during full beam operation and that will need to be effectively rejected to the atmosphere. Approximately 50% of the heat is required to be rejected to a low temperature heat sink that cannot be achieved by an evaporative cooling tower during summer. To operate during these summer months, a secondary chilled water refrigeration system will be required that would increase the cost of the cooling water system. Further, operating chiller compressor in the summer months will increase the energy consumption of the machine. This analysis is being prepared to evaluate the impact on operating and capital costs on the cooling system for various summer operating schedules while utilizing the most cost-effective scenario of an evaporative cooling system. The technology selection for the various heat sinks is addressed in a separate write-up and are not expected to change the conclusions of this write-up.

43 PARTICLE ACCELERATORS↗

Device separates hydrogen from solution in water at ambient temperatures

Separator decreases the partial pressure of hydrogen gas dissolved in the water produced by fuel cells containing an alkaline electrolyte. The unit eliminates the hazards associated with the release of hydrogen from water solution when the hydrostatic pressure is rapidly decreased.

Albright, C. F.↗

Cyclic-load crack growth in ASME SA-105 grade II steel in high-pressure hydrogen at ambient temperature

ASME SA-105 Grade II steel, which is used in high-pressure hydrogen compressor systems, is similar to steels used or considered for use in high-pressure hydrogen storage vessels and pipelines. This paper summarizes the results of a program conducted to provide cyclic-load crack growth rate (da/dN) data for a fracture mechanics analysis of a 15,000 psi hydrogen compressor facility which contains pulse quieter and after-cooler separator vessels constructed of the ASME SA-105 Grade II steel. Included in the program were tests performed to assist in establishing operating procedures that could minimize the effect of hydrogen on crack growth rates during operation.

Walter, R. J.↗

Ambient temperature fatigue tests of elements of an actively cooled honeycomb sandwich structural panel

Elements of an actively cooled structural panel for a hypersonic aircraft have been investigated for fatigue characteristics. The study involved a bonded honeycomb sandwich panel with d-shaped coolant tubes. The curved portion of these tubes was embedded in the honeycomb, and the flat portion was bonded or soldered to the inner surface of the outer skin. The elements examined were two plain skin specimens (aluminum alloy); two specimens with skins attached to manifolds and tubes (one specimen was bonded, the other soldered); and a specimen representative of a corner section of the complete cooled sandwich. Sinusoidal loads were applied to all specimens. The honeycomb sandwich specimen was loaded in both tension and compression; the other specimens were loaded in tension only. The cooling tubes were pressurized with oil throughout the fatigue tests. The most significant results of these tests follow: All specimens exceeded their design life of 20,000 cycles without damage. Crack growth rates obtained in the plain skin specimens were used to determine the crack growth characteristics of aluminum alloy. Cracks in skins either bonded or soldered to cooling tubes propagated past the tubes without penetration. The coolant tubes served as crack arresters and temporarily stopped crack growth when a crack reached a tube-skin interface. The honeycomb core demonstrated that it could contain leakage from a tube.

Sharpe, E. L.↗

Application of ion chromatography to the study of hydrolysis of some halogenated hydrocarbons at ambient temperatures

The application of ion chromatography to the study of very slow rates of hydrolysis of some halogenated hydrocarbons was investigated. The halide concentrations in the aqueous phase of mixtures of a carbonate buffer (pH = 10.3) and either chloroform (CHC13) or fluorotrichloromethane (CFC13) after aging for various lengths of time at room temperature, were determined by ion chromatography. Hydrolysis of CHC13 caused the C1(-) concentration to increase by about 1500 ppb per day. On the other hand neither the F(-) or C1(-) concentration in the CFC13 mixture increased by as much as 1 ppb per day. The magnitude of errors in the determination of halides prevented any firm conclusions regarding hydrolysis in this mixture. However, these results were used to show how ion chromatography could expedite identification of the hydrolyzing substance as well as investigations of hydrolysis mechanisms.

Otterson, D. A.↗

Rechargeable ambient temperature lithium cells

The cycling performance of a secondary lithium cell with a 2-methyl THF lithium hectofluorarsenate electrolyte is discussed. Stripping efficiency, dendritization, passivation on standing, and discharge efficiency are considered.

Holleck, G. L.↗

Factors affecting cycle life in ambient temperature of secondary lithium batteries

Three major factors are discussed: electrode integrity, electrolyte stability, and dendrite formation. It is concluded that elastomers can function as improved binders for rechargeable cathodes. The cathodes can retain integrity under long cycle life with no visual deteriorations. It is found that microelectrodes can be made from powdery cathode materials for voltammetry studies.

Somoano, R.↗