Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TUNNEL EFFECT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Real gas effects 2: Influence of condensation on minimum operating temperatures of cryogenic wind tunnels

Condensation effects are responsible for the minimum operating temperatures of cryogenic wind tunnels at total pressures up to about 9 atmospheres. The two primary modes of condensation homogeneous nucleation and heterogeneous nucleation and the conditions with which either may limit minimum operating temperatures are reveiwed. Previous hypersonic and supersonic condensation data are reviewed as are data taken in the nitrogen gas, Langley 0.3 Meter Transonic Cryogenic Tunnel. Analysis of data in the 0.3 m tunnel suggests that the onset of homogenous nucleation may be approximated by an analysis by sivier and that the onset of heterogeneous nucleation is only apparent just below free stream saturation. Extension of the results from the 0.3 m tunnel to other nitrogen gas cryogenic tunnels is discussed and is shown to depend on length scales, purity of the liquid nitrogen injected for cooling, number of particulates in the flow, and the extent to which the injected liquid nitrogen is evaporated.

Hall, R. M.↗
NASA NTRS1973

Full-scale wind-tunnel investigation of effects of slot spoilers on the aerodynamic characteristics of a light twin-engine airplane

A wind-tunnel investigation has been conducted to determine the effects of slot spoilers on the longitudinal and lateral aerodynamic characteristics of a full-scale mockup of a light twin-engine airplane. The slots were located along the leading edge of the flaps and were used to modulate the flap-induced lift as a possible means of achieving direct lift control. The data showed that the slots were effective in spoiling up to 61 percent of the flap-induced lift, but that an adverse pitching-moment change (nose up) accompanied opening the slots. Opening the slots was found to decrease slightly the downwash angle at the tail and to increase slightly the longitudinal stability of the model.

Verstynen, H. A., Jr.↗
NASA NTRS1986

Wall effects in wind tunnels

A synthesis of current trends in the reduction and computation of wall effects is presented. Some of the points discussed include: (1) for the two-dimensional, transonic tests, various control techniques of boundary conditions are used with adaptive walls offering high precision in determining reference conditions and residual corrections. A reduction in the boundary layer effects of the lateral walls is obtained at T2; (2) for the three-dimensional tests, the methods for the reduction of wall effects are still seldom applied due to a lesser need and to their complexity; (3) the supports holding the model of the probes have to be taken into account in the estimation of perturbatory effects.

Chevallier, J. P.↗
DOE OSTI2026

Nuclear–Electronic Orbital General Rate Theory: Predicting Hydrogen Kinetic Isotope Effects in the Deep Tunneling Regime

Hydrogen transfer is a critical component of many chemical and biological processes. The ratio of rate constants for hydrogen and deuterium transfer defines the H/D kinetic isotope effect (KIE), which is a powerful tool for elucidating hydrogen transfer mechanisms. Interpretation of experimental H/D KIEs relies on accurate and affordable computational methods. However, due to their light mass, hydrogen and deuterium can undergo tunneling, which is challenging to describe in multidimensional molecular systems. Herein, we introduce the nuclear–electronic orbital general rate theory (NEO-GRT), which enables the efficient prediction of H/D KIEs based on full-dimensional molecular quantum chemistry calculations. The NEO-GRT approach describes the hydrogen transfer rate constant with a general expression that spans the vibrationally adiabatic and nonadiabatic hydrogen tunneling regimes. The input quantities are computed using NEO density functional theory, which treats the transferring hydrogen or deuterium nucleus quantum mechanically on the same level as the electrons. We investigate two intramolecular proton transfer reactions in organic molecules at temperatures down to 50 K to evaluate the performance of NEO-GRT by comparison to transition state theory and ring-polymer instanton theory. The KIEs computed with NEO-GRT agree with those calculated using ring-polymer instanton theory for the full-dimensional molecular systems at the same level of electronic structure theory. This agreement indicates that NEO-GRT captures the deep hydrogen tunneling effects, in contrast to transition state theory, which neglects such effects. Given its relatively low computational cost, NEO-GRT is a promising approach for predicting H/D KIEs in large organic and organometallic systems.

Hydrogen↗
NASA NTRS1981

Jet V/STOL wind-tunnel simulation and groundplane effects

Low-speed wind-tunnel testing of V/STOL aircraft concepts to determine the aerodynamic-propulsion interaction effects during the transition between hover and wingborne flight is a necessary step in the development cycle of this type of aircraft. Powered models are normally used to determine the aerodynamic performance characteristics. This paper examines some of the pretest preparation necessary to define the objectives of an appropriate investigation. Several factors which influence the selection of the model concept and the engine simulator are discussed. In addition, some of the test techniques important for this class of aircraft model are examined. Finally, the paper reviews some of the wind-tunnel wall effects important to this type of aircraft testing with special emphasis on groundplane effects.

Margason, R. J.↗
NASA NTRS1973

Wind tunnel investigation of effects of variations in Reynolds number and leading-edge treatment on the aerodynamic characteristics of an externally blown jet-flap configuration

An investigation has been conducted in a full-scale tunnel to determine the effects of variations in Reynolds number and leading-edge treatment on the aerodynamic characteristics of an externally blown jet-flap transport configuration. The model had a double-slotted trailing-edge flap and was powered by four high-bypass-ratio turbofan engines. Tests were performed by using each of three leading-edge devices (a 30-percent-chord flap and 15- and 25-percent-chord slats) at Reynolds numbers from 0.47 x one million to 1.36 x one million thrust coefficients up to 3.5. The use of a 25-percent-chord slat was found to be more effective than a 15-percent-chord slat or a 30-percent-chord flap in extending the stall angle of attack and in minimizing the loss of lift after the stall. The large slat was also effective in reducing the rolling moments that occurred when the engine-out wing stalled first.

Parlett, L. P.↗
NASA NTRS1924

The effect of wind tunnel turbulence upon the forces measured on models

1. Reasons for inquiry: The tests were undertaken to find the effect of turbulence in the air stream upon the lift and drag forces measured on models in the four-foot wind tunnel at the Massachusetts Institute of Technology. 2. Range of investigation: Maximum lifts and minimum drags were measured on Gottingen-387 and R.A.F.-15 airfoils, minimum drag on a streamlined strut, and the static pressure gradients for different conditions of turbulence. 3. Results and further developments: The results show that the scale of the turbulence (as defined in this report) has a marked effect upon the measured forces on models tested in the tunnel as well as on the pressure gradient, and it is recommended that further investigation of the phenomena be made with the aid of smoke and small wind vanes.

Lepage, W L↗
NASA NTRS1948

Tests of a Triangular Wing of Aspect Ratio 2 in the Ames 12-foot Pressure Wind Tunnel III : the Effectiveness and Hinge Moments of a Skewed Wing-tip Flap

Results of wind-tunnel tests of a semispan model of a triangular wing of aspect ratio 2 with a skewed wing-tip flap are presented. Lift, drag, pitching-moment, and hinge-moment data are included for subsonic Mach numbers up to 0.95. The flap showed extremely high hinge moments and low effectiveness as a longitudinal control. Although less affected by compressibility, this flap is indicated to be inferior to a constant-chord flap when applied to this triangular wing.

MACH NUMBER EFFECTS - COMPLETE WINGS↗
NASA NTRS1972

Numerical calculation of boundary-induced interference in slotted or perforated wind tunnels including viscous effects in slots

A numerical method is presented for calculating the incompressible boundary-induced interference in wind tunnels of rectangular cross section with slotted or perforated walls. The method includes a wall representation which is capable of satisfying a generalized homogeneous boundary condition including the effects of viscosity within the slots. The effects of viscosity in the slots are found to be very significant. The method allows for a variation in the boundary conditions along the tunnel walls. The model can be any configuration and can be located anywhere in the test section. The interference can be computed at any point in the test section.

Keller, J. D.↗
NASA NTRS1947

Wind-Tunnel Investigation of Effects of Unsymmetrical Horizontal-Tail Arrangements on Power-on Static Longitudinal Stability of a Single-Engine Airplane Model

A wind-tunnel investigation has been made to determine the effects of unsymmetrical horizontal-tail arrangements on the power-on static longitudinal stability of a single-engine single-rotation airplane model. Although the tests and analyses showed that extreme asymmetry in the horizontal tail indicated a reduction in power effects on longitudinal stability for single-engine single-rotation airplanes, the particular "practical" arrangement tested did not show marked improvement. Differences in average downwash between the normal tail arrangement and various other tail arrangements estimated from computed values of propeller-slipstream rotation agreed with values estimated from pitching-moment test data for the flaps-up condition (low thrust and torque) and disagreed for the flaps-down condition (high thrust and torque). This disagreement indicated the necessity for continued research to determine the characteristics of the slip-stream behind various propeller-fuselage-wing combinations. Out-of-trim lateral forces and moments of the unsymmetrical tail arrangements that were best from consideration of longitudinal stability were no greater than those of the normal tail arrangement.

AIRFOILS - NACA 65(216-012(MOD ) - CHAR & MOMENTS ↗
NASA NTRS1985

Low-speed stability and control wind-tunnel investigations of effects of spanwise blowing on fighter flight characteristics at high angles of attack

The effects of spanwise blowing on two configurations representative of current fighter airplanes were investigated. The two configurations differed only in wing planform, with one incorporating a trapezoidal wing and the other a 60 delta wing. Emphasis was on determining the lateral-directional characteristics, particularly in the stall/departure angle-of-attack range; however, the effects of spanwise blowing on the longitudinal aerodynamics were also determined. The-tunnel tests included measurement of static force and forced-oscillation aerodynamic data, visualization of the airflow changes created by the spanwise blowing, and free-flight model tests. The effects of blowing rate, chordwise location of the blowing ports, asymmetric blowing, and blowing on the conventional aerodynamic control characteristics were investigated. In the angle-of-attack regions in which the spanwise blowing substantially improved the wing upper-surface flow field (i.e., provided reattachment of the flow aft of the leading-edge vortex), improvements in both static and dynamic lateral-directional stability were observed. Blowing effects on stability could be proverse or adverse depending on blowing rate, blowing port loaction, and wing planform. Free-flight model tests of the trapezoidal wing confirmed the beneficial effects of spanwise blowing measured in the static and dynamic force tests.

Satran, D. R.↗
NASA NTRS1996

Hypersonic Boundary Layer Stability Experiments in a Quiet Wind Tunnel with Bluntness Effects

Hypersonic boundary layer measurements over a flared cone were conducted in a Mach 6 quiet wind tunnel at a freestream unit Reynolds number of 2.82 million/ft. This Reynolds number provided laminar-to-transitional flow over the cone model in a low-disturbance environment. Four interchangeable nose-tips, including a sharp-tip, were tested. Point measurements with a single hot-wire using a novel constant voltage anemometer were used to measure the boundary layer disturbances. Surface temperature and schlieren measurements were also conducted to characterize the transitional state of the boundary layer and to identify instability modes. Results suggest that second mode disturbances were the most unstable and scaled with the boundary layer thickness. The second mode integrated growth rates compared well with linear stability theory in the linear stability regime. The second mode is responsible for transition onset despite the existence of a second mode subharmonic. The subharmonic disturbance wavelength also scales with the boundary layer thickness. Furthermore, the existence of higher harmonics of the fundamental suggests that nonlinear disturbances are not associated with 'high' free stream disturbance levels. Nose-tip radii greater than 2.7% of the base radius completely stabilized the second mode.

Lachowicz, Jason T.↗
NASA NTRS1938

Correction of Profile-Drag Results from Variable-Density Tunnel and the Effect on the Choice of Wing-Section Thickness

Profile-drag coefficients published from tests in the N.A.C.A. variable-density tunnel (Technical Reports Nos. 460, 537, 586, and 610, references 1 to 4) have tended to appear high as compared with results from the N.A.C.A. full-scale tunnel (Technical Report No. 530, reference 5) and from foreign sources (references 6 to 8). Such discrepancies were considered in Technical Report No. 586, and corrections for turbulence and tip effects were derived that tended to reduce the profile-drag coefficients, particularly for the thicker airfoils. The corrected profile-drag coefficients, designated by the lower-case symbol cdo as contrasted with the older CDO, have been employed in the airfoil reports published since Technical Report No. 460, but even these corrected results continued to appear high, particularly for the thicker sections. The important practical result is that a smaller increase of drag with airfoil thickness is indicated, which may be of primary importance to the airplane designer in choosing the optimum airfoil sections for actual wings. Further investigations of this subject were, of course, undertaken, one of the most important being an investigation of three symmetrical sections N.A.C A. 0009, 0012, and 0018 under conditions of low turbulence in the full-scale tunnel. Preliminary results from this investigation also indicate a smaller increase in drag with airfoil thickness than the results from the variable-density tunnel. Furthermore, comparative tests made in the two tunnels by applying strings to the surface of the N.A.C.A. 0012 airfoil to move the transition point to a predetermined position indicated that the effective reynolds Number concept would account approximately for the drag as affected by the position of transition from laminar to turbulent flow in the boundary layer.

Jacobs, Eastman N.↗
DOE OSTI2024

Quantum sensing effect of electron tunneling in DQD/analyte complex

We investigate electron tunneling between quantum dots and molecules to propose a quantum sensor. This sensor consists of double quantum dots (DQD) with energy levels specifically tailored to mirror those of the target analyte. By analyzing the spectral distribution of electron localizations in the DQD system, we can delineate the analyte’s spectrum and deduce its composition by comparing it with a reference sample. To understand electron tunneling dynamics within the DQD/analyte complex, we performed three-dimensional computational modeling applying the effective potential approach to the InAs/GaAs heterostructure. In this modeling, we mimicked the analyte spectrum by utilizing a quantum well characterized by a quasi-discrete spectrum. Our calculations reveal the inherent potential of utilizing this method as a highly sensitive and selective sensor.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
NASA NTRS1974

Continued investigations in the NAAL low speed wind tunnel into the effects of the air breathing propulsion system on orbiter subsonic stability and control characteristics (OA62A)

Experimental aerodynamic investigations were conducted on a stingmounted 0.0405-scale representation (model 43-0) of the 140A/B Space Shuttle Orbiter in a Low Speed Wind Tunnel. The NASA designation for this test was 0A62A. The primary test objective was to continue studies, initiated on tests 0A16 and 0A71A and 0A71C, in optimizing the air breathing propulsion system (ABPS) and investigating the aerodynamic effects of various nacelle number/location configurations on the orbiter stability and control characteristics. Orbiter stability and control characteristics, both with and without ABPS, were investigated at elevon deflections of 0, + or -5, + or -19, + or -5, and -20 deg; aileron deflections of 0 and 10 deg (about 0 deg elevon); and rudder deflections of 0, -7.5, and -15 deg. Aerodynamic force and moment data was measured in the body axis system by a 2.5-inch task type internal balance. The model was sting supported through the base region with a nominal angle of attack range of -4 to 30 deg. Yaw polars were recorded over the beta range of -10 to 10 deg at fixed angles of attack of 0, 5, 10, and 15 deg.

Mennell, R.↗
NASA NTRS1939

Wind-tunnel Investigation of Effect of Yaw on Lateral-stability Characteristics I : Four N.A.C.A. 23012 Wings of Various Plan Forms with and Without Dihedral

Four N.A.C.A. 23012 wings were tested at several angles of yaw in the N.A.C.A. 7- by 10-foot wind tunnel. All the wings have rounded tips and, in plan form, one is rectangular and the others are tapered 3:1 with various amounts of sweep. Each wing was tested with two amounts of dihedral and with partial-span split flaps. The coefficients of lift, drag, and pitching moment are given for all the models at zero yaw. The coefficients of rolling moment, yawing moment, and side force are given for the rectangular wing at all values of yaw tested. The rate of change in the coefficients with angle of yaw is given in convenient form for stability calculations.

Bamber, M J↗