Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TOKAMAK DEVICES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2012

Recent improvements of the JET lithium beam diagnostic

A 60 kV neutral lithium diagnostic beam probes the edge plasma of JET for the measurement of electron density profiles. This paper describes recent enhancements of the diagnostic setup, new procedures for calibration and protection measures for the lithium ion gun during massive gas puffs for disruption mitigation. New light splitting optics allow in parallel beam emission measurements with a new double entrance slit CCD spectrometer (spectrally resolved) and a new interference filter avalanche photodiode camera (fast density and fluctuation studies).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Kinetic equilibrium reconstructions of plasmas in the MAST database and preparation for reconstruction of the first plasmas in MAST upgrade

Reconstructions of plasma equilibria using magnetic sensors were routine during operation of the Mega Ampere Spherical Tokamak (MAST) device, but reconstructions using kinetic profiles were not. These are necessary for stability and disruption analysis of the MAST database, as well as for operation in the upgrade to the device, MAST-U. The three-dimensional (3D) code VALEN is used to determine eddy currents in the 3D vessel structures for vacuum coil test shots, which are then mapped to effective resistances in the two-dimensional vessel groupings in the EFIT equilibrium reconstruction code to be used in conjunction with nearby loop voltage measurements for estimated currents in the structures during reconstruction. Kinetic equilibrium reconstructions with EFIT, using all available magnetic sensors as well as Thomson scattering measurements of electron temperature and density, charge exchange recombination spectroscopy measurements of ion temperature, and internal magnetic field pitch angle measurements from a motional Stark effect (MSE) diagnostic are performed for a large database of MAST discharges. Excellent convergence errors are obtained for the portions of the discharges where the stored energy was not too low, and it is found that reconstructions performed with temperature and density measurements but without MSE data usually already match the pitch angle measurements well. A database of 275 kinetic equilibria is used to test the ideal MHD stability calculation capability for MAST. In conclusion, the necessary changes to conducting structure in VALEN, and diagnostic setup in EFIT have been completed for the upgrade from MAST to MAST-U, enabling kinetic reconstructions to commence from the first plasma discharges of the upgraded device.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Point containment algorithms for constructive solid geometry with unbounded primitives

Here, we present several algorithms for evaluating point containment in constructive solid geometry (CSG) trees with unbounded primitives. Three algorithms are presented based on postfix, prefix, and infix notations of the CSG binary expression tree. We show that prefix and infix notations enable short-circuiting logic, which reduces the number of primitives that must be checked during point containment. To evaluate the performance of the algorithms, each algorithm was implemented in the OpenMC Monte Carlo particle transport code, which relies on CSG to represent solid bodies through which subatomic particles travel. Two sets of tests were carried out. First, the execution time to generate a rasterized image of a 2D slice of three CSG models of varying complexity was measured. Use of both prefix and infix notations offered significant speedup over the postfix notation that has traditionally been used in particle transport codes, with infix resulting in a 6 x reduction in execution time relative to postfix for a model of a tokamak fusion device. We then measured the execution time of neutron transport simulations of the same three models using each of the algorithms. The results and performance improvements reveal the same trends as for the rasterization test, with a 5.52 x overall speedup using the infix notation relative to the original postfix notation in OpenMC for the tokamak model.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

On the possibility of reducing the instability threshold of a parametric decay of an extraordinary wave into two upper hybrid waves in an inhomogeneous plasma

A parametric decay instability (PDI) of an extraordinary wave leading to excitation of two upper hybrid (UH) plasmons at frequencies close to half the pump wave frequency is analyzed. It is shown that the two-plasmon PDI power threshold can be significantly reduced under conditions of electron cyclotron resonance heating (ECRH) experiments in toroidal magnetic devices, where the plasma density profile is often nonmonotonic, which leads to the localization of UH waves.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

Recombination of H atoms on the dust in fusion plasmas

We survey a model for theoretical study of the interaction of hydrogen and dust surface and apply our results for dusty plasmas to fusion devices. In this model, considering the mobility of ad-atoms from one physisorbed, or chemisorbed site, to other one by thermal diffusion, we describe the formation of H{sub 2} on grain surfaces. Finally, we calculate the formation rate on the high temperature dust surfaces for a range of temperature and density in typical conditions of divertor of tokamak.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Magnetic topology and current channels in plasmas with toroidal current density inversions

The equilibrium magnetic field inside axisymmetric plasmas with inversions on the toroidal current density is considered. Previous works have shown that internal regions with negative current density lead to non-nested magnetic surfaces inside the plasma. Following these results, we derive a general expression relating the positive and negative currents inside the non-nested surfaces. This is done in terms of an anisotropy parameter that is model-independent and is based in very general properties of the magnetic field. We demonstrate that the positive currents in axisymmetric islands screen the negative one in the plasma center by reaching about twice its magnitude. Further, we illustrate these results by developing a family of analytical local solutions for the poloidal magnetic field in a region of interest that contains the inverted current. These local solutions exhibit non-nested magnetic surfaces with a combined current of at least twice the magnitude of the negative one, as prescribed from the topological arguments, and allow to study topological transitions driven by geometrical changes in the current profile. To conclude, we discuss the signatures of internal current density inversions in a confinement device and show that magnetic pitch measurements may be inappropriate to differentiate current reversals and small current holes in plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2012

Design and implementation of a multichannel millimeter wave interferometer for the Compact Toroidal Hybrid experiment

A three-channel 1 mm wave interferometer has been designed, assembled, and installed on the Compact Toroidal Hybrid torsatron (CTH). The interferometer design makes novel use of a subharmonic mixer for detection, which simplifies alignment. It employs a single electronically tunable source that is repetitively chirped using a sawtooth waveform of frequency up to 1 MHz. The 15.25 GHz drive oscillator is multiplied in two stages to 122 GHz before a final doubler stage brings it to 244 GHz. Local oscillator (LO) power at 122 GHz is directed through waveguide to the LO input of the subharmonic mixer of each viewing chord, simplifying alignment. Phase detection is performed by directly digitizing the amplified mixer outputs at 50 MHz and processing them with a software algorithm. Initial measurements made with the central chord of the new interferometer agree with those from the existing 4 mm system at low densities. The 1 mm system performs well in current-driven discharges reaching densities over 10{sup 19} m{sup -3}, whereas the lower frequency interferometer is found to be less reliable due to loss of fringes. This is a critical improvement for experiments studying the onset, avoidance, and vacuum magnetic transform dependence of disruptions in the CTH device.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2019

Final technical report for DE-FG02-06ER54871 Multi-Machine Validation of Fluid and Gyrokinetic Turbulence Models

This final report for the DE-FG02-06ER54871 “Multi-Machine Validation of Fluid and Gyrokinetic Turbulence Models” award (previously titled “Validation of Plasma Turbulence Models” during 2006-2010) documents accomplishments made over the full funding period of 6/1/2006 – 5/31/2018. The accomplishments can be broadly divided into two groups. First are integrated experimental and computational studies of fundamental drift-wave turbulence and shear flow dynamics, carried out using the Controlled Shear Decorrelation Experiment (CSDX) linear plasma experiment at UCSD and various fluid-based simulation models. The second set of accomplishments relates to validation studies of gyrokinetic and gyrofluid turbulence models of core tokamak turbulence, generally using data from the DIII-D tokamak operated by General Atomics. A number of results bridge these areas, such as investigations into bispectral energy transfer and shear flow generation at L-H transitions, carried out on a number of different experimental platforms. Some of the key accomplishments supported by this work include (1) the first experimental observations of nonlinear shear flow generation by drift-wave turbulence in a magnetized plasma, (2) detailed documentation of nonlinear interactions and energy transfer between drift-waves and zonal flows in both linear devices and tokamaks, (3) experimental and numerical investigations of parallel boundary condition effects on resistive drift-wave turbulence, (4) pioneering development of synthetic diagnostics for core tokamak turbulence validation studies, along with a system of validation metrics, and (5) extensive investigation of the fidelity of gyrokinetic and gyrofluid turbulent transport models in tokamaks which have significantly advanced our understanding of where these models can (and can not) reproduce experimental observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Analysis of the influence of external biasing on Texas Helimak turbulence

We analyze alterations on the electrostatic turbulence in experiments with imposed bias to control the plasma radial electric field in Texas Helimak (K. W. Gentle and H. He, Plasma Sci. Technol. 10, 284 (2008)), a toroidal plasma device with a one-dimensional equilibrium, magnetic curvature, and shear. Comparing discharges from different biased potentials, we identify, in a roughly uniform gradient region, a continuous variation from low turbulence level and narrower frequency spectra, for negative bias, to high turbulence level and broadband spectra for positive bias. Overall, we distinguish two kinds of perturbed turbulence, classified according to their intensity, spectral, statistical, and recurrence properties. When the bias is positive, the turbulence shows enhanced and broadband spectra with non Gaussian probability distribution functions having noticeable long tails (extreme events) similar to the turbulence in tokamak scrape-off layer. On the other hand, negative bias reduces the turbulence level and decreases the spectrum widths. Also for negative bias, we found large frequency widths whenever the coupling between drift waves and the sheared plasma flow is fast enough to allow the enhancement of sidebands modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Fluctuations and intermittent poloidal transport in a simple toroidal plasma

In a simple magnetized toroidal plasma, fluctuation induced poloidal flux is found to be significant in magnitude. The probability distribution function of the fluctuation induced poloidal flux is observed to be strongly non-Gaussian in nature; however, in some cases, the distribution shows good agreement with the analytical form [Carreras et al., Phys. Plasmas 3, 2664 (1996)], assuming a coupling between the near Gaussian density and poloidal velocity fluctuations. The observed non-Gaussian nature of the fluctuation induced poloidal flux and other plasma parameters such as density and fluctuating poloidal velocity in this device is due to intermittent and bursty nature of poloidal transport. In the simple magnetized torus used here, such an intermittent fluctuation induced poloidal flux is found to play a crucial role in generating the poloidal flow.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

Energy and momentum preserving Coulomb collision model for kinetic Monte Carlo simulations of plasma steady states in toroidal fusion devices

A kinetic Monte Carlo model suited for self-consistent transport studies is proposed and tested. The Monte Carlo collision operator is based on a widely used model of Coulomb scattering by a drifting Maxwellian and a new algorithm enforcing the momentum and energy conservation laws. The difference to other approaches consists in a specific procedure of calculating the background Maxwellian parameters, which does not require ensemble averaging and, therefore, allows for the use of single-particle algorithms. This possibility is useful in transport balance (steady state) problems with a phenomenological diffusive ansatz for the turbulent transport, because it allows a direct use of variance reduction methods well suited for single particle algorithms. In addition, a method for the self-consistent calculation of the electric field is discussed. Results of testing of the new collision operator using a set of 1D examples, and preliminary results of 2D modelling in realistic tokamak geometry, are presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2014

Monte Carlo simulation of a Bonner sphere spectrometer for application to the determination of neutron field in the Experimental Advanced Superconducting Tokamak experimental hall

To assess the neutron energy spectra and the neutron dose for different positions around the Experimental Advanced Superconducting Tokamak (EAST) device, a Bonner Sphere Spectrometer (BSS) was developed at Peking University, with totally nine polyethylene spheres and a SP9 {sup 3}He counter. The response functions of the BSS were calculated by the Monte Carlo codes MCNP and GEANT4 with dedicated models, and good agreement was found between these two codes. A feasibility study was carried out with a simulated neutron energy spectrum around EAST, and the simulated “experimental” result of each sphere was obtained by calculating the response with MCNP, which used the simulated neutron energy spectrum as the input spectrum. With the deconvolution of the “experimental” measurement, the neutron energy spectrum was retrieved and compared with the preset one. Good consistence was found which offers confidence for the application of the BSS system for dose and spectrum measurements around a fusion device.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2014

Analysis of the cryogenic system behavior for pulsed heat load in EAST

EAST is the first full superconducting fusion device. The plasma is confined by the magnetic fields generated from a large set of superconducting magnets which are made of cable in-conduit conductor (CICC). In operation, these magnets suffer heat loads from thermal and nuclear radiation from the surrounding components and plasma as well as the eddy currents and the AC losses generated within the magnets, together with the heat conduction through supports and the resistive heat generated at the current lead transiting to room temperature. The cryogenic system of our EAST consists of a 2kW/4K helium refrigerator and a distribution system for the cooling of poloidal field (PF) and toroidal field (TF) coils, structures, thermal shields, buslines and current leads. Pulsed heat load is the main difference between the cryogenic system of a full superconducting Tokamak system and other large scale cryogenic systems. The cryogenic system operates in a pulsed heat loads mode requiring the helium refrigerator to remove periodically large heat loads in time. At the same time, the cryogenic system parameters such as helium cooling superconducting magnets, helium refrigerator and helium distribution system are changing. In this paper, the variation range of the parameters of superconducting magnets and refrigerator has been analyzed in the typical plasma discharge mode. The control scheme for the pulsed loads characteristics of the cryogenic system has been proposed, the implementation of which helps to smooth the pulse loads and to improve the stability of the operation of the cryogenic system.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2013

Development of a compact thermal lithium atom beam source for measurements of electron velocity distribution function anisotropy in electron cyclotron resonance plasmas

The anisotropy of the electron velocity distribution function (EVDF) in plasmas can be deduced from the polarization of emissions induced by anisotropic electron-impact excitation. In this paper, we develop a compact thermal lithium atom beam source for spatially resolved measurements of the EVDF anisotropy in electron cyclotron resonance (ECR) plasmas. The beam system is designed such that the ejected beam has a slab shape, and the beam direction is variable. The divergence and flux of the beam are evaluated by experiments and calculations. The developed beam system is installed in an ECR plasma device with a cusp magnetic field, and the LiI 2s–2p emission (670.8 nm) is observed in low-pressure helium plasma. The two-dimensional distributions of the degree and direction of the polarization in the LiI emission are measured by a polarization imaging system. The evaluated polarization distribution suggests the spatial variation of the EVDF anisotropy.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2013

Spontaneous three-dimensional magnetic reconnection in merging toroidal plasma experiment

We investigated a new phenomenon of three-dimensional (3D) magnetic reconnection in TS-4 torus plasma merging experiments by directly measuring the 3D structures of the current sheet. Removal of all toroidal asymmetry of the device reveals that a strong external drive of reconnection inflow increases the toroidal asymmetry of the current sheet only during the reconnection. This spontaneous 3D deformation of the current sheet increases the reconnection outflow as well as the reconnection electric field, probably because local compression of the current sheet to a thickness less than the ion gyroradius triggers its strong dissipation of the current sheet, responsible for the onset of 3D reconnection. These mechanisms indicate that the 3D reconnection is a newly observed spontaneous process of fast reconnection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Toroidal magnetic field ripple in the presence of misaligned toroidal field coils on the COMPASS-U tokamak

Homogeneity of the toroidal magnetic field is a critical aspect of the tokamak fusion device. It is affected by the design of toroidal magnetic field coils and their manufacturing and assembly misalignments. The magnetic field of the COMPASS-U project is analysed using toroidal field ripple quantity. Here ANSYS modelling of bitter-plate-designed toroidal field coils is performed to prepare an accurate simplistic representation of the coils using a virtual current line. Toroidal field ripple is analysed using a Gaussian distribution of possible misalignments. The worst-case toroidal field ripple corresponding to the technical drawings only slightly exceeds the chosen limit of 0.5%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

NSTX-U theory, modeling and analysis results

Here, the mission of the low aspect ratio spherical tokamak NSTX-U is to advance the physics basis and technical solutions required for optimizing the configuration of next-step steady-state tokamak fusion devices. NSTX-U will ultimately operate at up to 2 MA of plasma current and 1 T toroidal field on axis for 5 s, and has available up to 15 MW of neutral beam injection power at different tangency radii and 6 MW of high harmonic fast wave heating. With these capabilities NSTX-U will develop the physics understanding and control tools to ramp-up and sustain high performance fully non-inductive plasmas with large bootstrap fraction and enhanced confinement enabled via the low aspect ratio, high beta configuration. With its unique capabilities, NSTX-U research also supports ITER and other critical fusion development needs. Super-Alfvénic ions in beam-heated NSTX-U plasmas access energetic particle (EP) parameter space that is relevant for both α-heated conventional and low aspect ratio burning plasmas. NSTX-U can also generate very large target heat fluxes to test conventional and innovative plasma exhaust and plasma facing component solutions. This paper summarizes recent analysis, theory and modelling progress to advance the tokamak physics basis in the areas of macrostability and 3D fields, EP stability and fast ion transport, thermal transport and pedestal structure, boundary and plasma material interaction, RF heating, scenario optimization and real-time control.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2013

Plasma flow at a high Mach-number

Unlike the case of static magnetohydrodynamic (MHD) equilibria, where an expansion in large aspect ratio of toroidal devices is common, cases of MHD equilibria with flow are rarely treated this way, and when this is done the expansion tends to be only partial. The main reason for the difference seems to be the difficulty of expanding the larger system of equilibrium equations with flow. Here, we use a recent expansion technique which employs a variational principle to simplify the process [E. Hameiri, Phys. Plasmas 20, 024504 (2013)]. We treat four cases of MHD equilibria with flow, developing their asymptotic expansions in full, and for an application consider the effect of the flow on the Shafranov shift.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗