SEARCH · Engineering Papers

Results for “THERMOELASTICITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Thermomechanical Fatigue Behavior of Three Cfcc's

The thermomechanical fatigue (TMF) behavior of three continuous-fiber ceramic composites (CFCC's) was examined. The three matrices consisted of two different glass-ceramics and silicon carbide, respectively. The matrices of some of the specimens with the silicon carbide matrix were enhanced to improve oxidation resistance. All three were reinforced with Nicalon fibers with various fiber architectures. The thermoelastic properties of the matrix relative to the fibers, the elastic moduli and coefficients of thermal expansion (CTE), were different in each composite, providing a comparison of the effects of these critical properties. The specimens were tested under in-phase (IP) and out-of-phase (OP) cyclic loadings with respect to thermal cycling between 600 C and 1100 C. One of the glass-ceramic composites had greatly increased TMF lives compared to the other glass-ceramic matrix composites. This was probably caused by the reversal of the CTE mismatch between the fibers and the matrices and caused by the different oxidation resistances of the composites. For the same TMF lives a cross-ply reinforced composite had a maximum cyclic stress half as great, as that of unidirectionally reinforced composite. This indicated that the (0 deg) ply fibers had a strong influence of TMF life. Both the glass ceramic matrix composites had shallow-slope stress-life plots that indicated sensitivity to damage and therefore low damage tolerance. The composites with an unenhanced silicon carbide matrix experienced the shortest TMF lives of all the CFCC's tested. However, the enhanced composite had the longest. Also, the enhanced composite demonstrated the best damage tolerance as evidenced by a stress-life curve that curves sharply upward to the left. In all the composites, out-of-phase cyclic loading was worse than in-phase cyclic loadings despite the CTE mismatch between fiber and matrix. A damage investigation and a preliminary analysis of the stresses in the fibers and matrices taking into account their respective thermoelastic properties provided insight into the relative behavior of the glass-ceramic matrix composites under IP and OP TMF.

Worthem, Dennis W.↗

NASA NTRS1999

Technologies for Nondestructive Evaluation of Surfaces and Thin Coatings

The effort included in this project included several related activities encompassing basic understanding, technological development, customer identification and commercial transfer of several methodologies for nondestructive evaluation of surfaces and thin surface coatings. Consistent with the academic environment, students were involved in the effort working with established investigators to further their training, provide a nucleus of experienced practitioners in the new technologies during their industrial introduction, and utilize their talents for project goals. As will be seen in various portions of the report, some of the effort has led to commercialization. This process has spawned other efforts related to this project which are supported from outside sources. These activities are occupying the efforts of some of the people who were previously supported within this grant and its predecessors. The most advanced of the supported technologies is thermography, for which the previous joint efforts of the investigators and NASA researchers have developed several techniques for extending the utility of straight thermographic inspection by producing methods of interpretation and analysis accessible to automatic image processing with computer data analysis. The effort reported for this technology has been to introduce the techniques to new user communities, who are then be able to add to the effective uses of existing products with only slight development work. In a related development, analysis of a thermal measurement situation in past efforts led to a new insight into the behavior of simple temperature probes. This insight, previously reported to the narrow community in which the particular measurement was made, was reported to the community of generic temperature measurement experts this year. In addition to the propagation of mature thermographic techniques, the development of a thermoelastic imaging system has been an important related development. Part of the work carried out in the effort reported here has been to prepare reports introducing the newly commercially available thermoelastic measurements to the appropriate user communities.

Source record↗

NASA NTRS2005

Input Files and Procedures for Analysis of SMA Hybrid Composite Beams in MSC.Nastran and ABAQUS

A thermoelastic constitutive model for shape memory alloys (SMAs) and SMA hybrid composites (SMAHCs) was recently implemented in the commercial codes MSC.Nastran and ABAQUS. The model is implemented and supported within the core of the commercial codes, so no user subroutines or external calculations are necessary. The model and resulting structural analysis has been previously demonstrated and experimentally verified for thermoelastic, vibration and acoustic, and structural shape control applications. The commercial implementations are described in related documents cited in the references, where various results are also shown that validate the commercial implementations relative to a research code. This paper is a companion to those documents in that it provides additional detail on the actual input files and solution procedures and serves as a repository for ASCII text versions of the input files necessary for duplication of the available results.

Turner, Travis L.↗

NASA NTRSDate not supplied

Characterizing Martian Volcanic Provinces’ Magmatic Evolution and Chemistry through Equations of State Modeling Initial Study

Here we discuss a novel interdisciplinary approach to investigating igneous compositions of large volcanic provinces on Mars using remote sensing data sets (Mars Odyssey Gamma Ray and neutron Spectrometer suite--GRS, and gravity) to inform petrologic and thermoelastic modeling. Martian volcanic provinces, starting from Noachian to Amazonian age, including Elysium (EVP), are locations of great geologic interest which have been active over long time scales from Hesperian to Amazonian. Regional scale change in eruptive processes are poorly understood. Compared to large igneous provinces on Earth, the martian volcanic activity has persisted for orders of magnitude longer. Therefore, changes in mantle chemistry, pressure, and temperature during lithospheric cooling are expected to produce significant changes in the conditions of magma production, storage and ascent, affecting the degree of fractional crystallization and crustal contamination. In this study, we perform a detailed modeling to test the hypothesis that compositional variability within volcanic provinces resulted from spatiotemporal changes in the depth of magma formation and present initial results. Our methods include constraining the pressure and temperature conditions of EVP as a case study of geologically recent magmatic evolution on Mars using GRS informed surface chemistry constraints and pMELTS modeling. Second, we place constraints on the density and seismic velocities of the EVP melt through thermoelastic modeling with a local gravity analysis. This analysis is also extended to Noachian aged volcanic provinces on Mars initial results estimates mantle pressure for each sub-region is 16 kbar pressure, whereas, degree of partial melting is low and varies between 10 to 12. This study aims to validate our theoretical model and develop a perspective view of spatiotemporal changes at the interior of Mars throughout the time.

Martian science, Mars, geology, geophysics↗

NASA NTRSDate not supplied

Multiscale Modeling of Thermoplastics Using Atomistic-informed Micromechanics

A multiscale model was developed for predicting the thermoelastic behavior of semi-crystalline thermoplastic materials for composite aerospace applications. At the highest scale containing the semi-crystalline spherulite in an amorphous matrix, the generalized method of cells, or high fidelity method of cells, was used to perform the homogenization calculations to obtain the effective properties. Models were developed assuming a cubic, or spherical shape, for the spherulite to understand if the morphology of the spherulite affects the effective thermoelastic properties. The generalized method of cells was used to model at the repeating unit cells at the subscales of the microstructure including the lamellae stacks and granular crystal blocks. The scales are integrated using the multiscale micromechanics method in the NASA Multiscale Analysis Tool. Data from molecular dynamics simulations were used as inputs for the amorphous and crystalline constituents. Convergence studies were performed to determine the best level of discretization for the repeating unit cell at the highest scale. Effective Young’s modulus, shear modulus, Poisson’s ratio, coefficient of thermal expansion, and thermal conductivity were predicted for polyether ether ketone and polyether ketone ketone, and very good agreement between the model utilizing the cubic spherulite and the experimental data, where available, was observed for polyether ketone ketone. Normalization of the data for the bulk polyether ketone ketone, against amorphous data, improved the predictions as compared to experimental data. Overall, the high fidelity method of cells predicted a stiffer response then the generalized method of cells as the crystallinity was increased. The shape of the spherulite had a minimal effect on the predicted bulk properties of the polymers.

thermoplastics↗

NASA NTRS2022

Lightweight Composite Reflectarray That Can Be Flattened, Folded, and Coiled for Compact Stowage

Herein is presented a design for a lightweight 5m 1m radio-frequency (RF) re ector that can be attened, folded, and coiled for compact stowage on board an ESPA-class spacecraft. The re ector is a re ectarray that operates at 3.2GHz. Compared to state- of-the-art technologies for RF re ectors, the presented design has advantages in terms of areal density, sti ness, deployed stability, and scalability. Thermal and structural analysis is presented to demonstrate deployed sti ness and thermoelastic stability of the proposed design. Thermal analysis is used to predict in- space deployed temperatures in an operational condition, and structural nite element analysis is used to predict deployed vibration modes and frequencies, and the thermoelastic deformation of the deployed re ector. Also presented are the fabrication, assembly, and testing of two one-third-scale-length full-scale-width 1:7m 1m test articles. These test articles are used to experimentally demonstrate RF functioning, stowage, deployment, and RF performance after deployment.

Pellegrino, Sergio↗

NASA NTRS2024

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

Formation and migration of austenite-martensite interfaces plays the key role in reversible martensitic transformations of shape memory alloys (SMAs). How these interfaces interact with the SMA microstructure is a primary determining factor in important functional properties such as hysteresis and transformation span. As such, successful microstructural engineering of SMAs requires in-depth knowledge of interface behavior. The rapid nature of martensitic transformations makes experimental observations of moving austenite-martensite interfaces challenging. Molecular dynamics (MD) simulation is a unique tool which can probe the atomic-scale details of austenite-martensite interfaces as they migrate through different microstructures. However, in focusing on the entire transformation process, including the nucleation of new phases, MD studies are usually performed so far from equilibrium that their relevance to experiment is questionable. Here, we demonstrate new MD techniques to generate energetically preferred austenite-martensite interfaces in NiTi under near-equilibrium conditions. The interfaces are semi-coherent, exhibiting a series of structural disconnections, and they can migrate rapidly through single crystals under only small thermodynamic driving forces. In contrast, when interfaces migrate in polycrystals, their motion is impeded by thermoelastic effects as well as changes in orientation relationships at grain boundaries. Microstructures which accumulate large amounts of elastic energy tend to release some fraction through irreversible, hysteresis-inducing mechanisms. We demonstrate that engineering microstructures with less constraints is a viable strategy to produce SMAs with reduced hysteresis and transformation span. Similar thermoelastic and hysteresis-inducing mechanisms also arise when austenite-martensite interfaces encounter precipitates and can be controlled by tuning characteristics of the precipitate distribution.

Gabriel Plummer↗

NASA NTRSDate not supplied

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

The formation and migration of austenite-martensite interfaces plays the key role in reversible martensitic transformations of shape memory alloys (SMAs). How these interfaces interact with the SMA microstructure is a primary determining factor in important functional properties such as hysteresis and transformation span. As such, successful microstructural engineering of SMAs requires in-depth knowledge of interface behavior. The rapid nature of martensitic transformations makes experimental observations of moving austenite-martensite interfaces challenging. Molecular dynamics (MD) simulation is a unique tool which can probe the atomic-scale details of austenite-martensite interfaces as they migrate through different microstructures. However, in focusing on the entire transformation process, including the nucleation of new phases, MD studies are usually performed so far from equilibrium that their relevance to experiment is questionable. Here, we demonstrate new MD techniques to generate energetically preferred austenite-martensite interfaces in NiTi under near-equilibrium conditions. The interfaces are semi-coherent, exhibiting a series of structural disconnections, and they can migrate rapidly through single crystals under only small thermodynamic driving forces. In contrast, when interfaces migrate in polycrystals, their motion is impeded by thermoelastic effects as well as changes in orientation relationships at grain boundaries. Microstructures which accumulate large amounts of elastic energy tend to release some fraction through irreversible, hysteresis-inducing mechanisms. We demonstrate that engineering microstructures with less constraints is a viable strategy to produce SMAs with reduced hysteresis and transformation span. Similar thermoelastic and hysteresis-inducing mechanisms also arise when austenite-martensite interfaces encounter precipitates and can be controlled by tuning characteristics of the precipitate distribution.

Gabriel Plummer↗

NASA NTRSDate not supplied

Molecular Dynamics Simulations of Microstructural Effects on Austenite-Martensite Interfaces in NiTi

Gabriel Plummer↗

DOE OSTI2025

Modelling the brittle failure of graphite induced by the controlled impact of runaway electrons in DIII-D

The thermo-mechanical response of an ATJ graphite sample to controlled runaway electron (RE) dissipation, realized in DIII-D, is modelled with a novel work-flow that features the RE orbit code KORC, the Monte Carlo particle transport code Geant4 and the finite element multiphysics software COMSOL. KORC provides the RE striking positions and momenta, Geant4 calculates the volumetric energy deposition and COMSOL simulates the thermoelastic response. Brittle failure is predicted according to the maximum normal stress criterion, which is suitable for ATJ graphite owing to its linear elastic behavior up to fracture and its isotropic mechanical properties. Measurements of the conducted energy, damage topology, explosion timing and blown-off material volume, impose a number of empirical constraints that suffice to distinguish between different RE impact scenarios and to identify RE parameters which provide the best match to the observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1964

The synthesis of a laminated plate for high temperature application

Synthesis of laminated plate for high temperature application - thermoelastic system

LAMINATED MATERIAL↗

DOE OSTI2021

The dynamic evolution of swelling in nickel concentrated solid solution alloys through in situ property monitoring

Defects and microstructural features spanning the atomic level to the microscale play deterministic roles in the expressed properties of materials. Yet studies of material evolution in response to environmental stimuli most often correlate resulting performance with one dominant microstructural feature only. In this work, the dynamic evolution of swelling in a series of Ni-based concentrated solid solution alloys under high-temperature irradiation exposure is observed using continuous, in situ measurements of thermoelastic properties in bulk specimens. Unlike traditional evaluation techniques which account only for volumetric porosity identified using electron microscopy, direct property evaluation provides an integrated response across all defect length scales. In particular, the evolution in elastic properties during swelling is found to depend significantly on the entire size spectrum of defects, from the nano- to meso-scales, some of which are not resolvable in imaging. Observed changes in thermal transport properties depend sensitively on the partitioning of electronic and lattice thermal conductivity. This emerging class of in situ experiments, which directly measure integrated performance in relevant conditions, provides unique insight into material dynamics otherwise unavailable using traditional methods.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Novel application of the modal strain energy technique for state-of-the-art damping predictions

Structural damping, which measures the energy dissipation of a vibrating structure, is a key modeling input for lightweight structures but is notoriously hard to predict. This work utilizes vibration-based measurements of centimeter-scale coupons and the modal strain energy approach to predict structural damping of a lightly damped structure. The approach was originally validated with panels shorter than a meter in length. This work extends the validation to a 2.75 m beam made of unidirectional and biaxial glass fiber laminates bonded by adhesive. The comparison between three-dimensional finite element model predictions and full-scale experimental measurements of damping show an average error of 5.2% for the first five modes. Additionally, the modal strain energy approach is newly applied with a one-dimensional geometrically exact beam theory model and a two-dimensional sectional analysis solver. This beam approach accurately predicts the damping behavior of the first bending modes but loses accuracy for higher order modes that are dominated by three-dimensional effects. This novel approach provides faster simulations while allowing arbitrary beam cross sections. The paper also investigates traditional and high-force dynamic mechanical analysis to measure structural damping of coupons. Both alternatives show significant errors in attempted validation against the theoretical thermoelastic damping of aluminum coupons.

17 WIND ENERGY↗

DOE OSTI2024

The EGS Collab project: Outcomes and lessons learned from hydraulic fracture stimulations in crystalline rock at 1.25 and 1.5 km depth

With the goal of better understanding stimulation in crystalline rock for improving enhanced geothermal systems (EGS), the EGS Collab Project performed a series of stimulations and flow tests at 1.25 and 1.5 km depths. The tests were performed in two well-instrumented testbeds in the Sanford Underground Research Facility in Lead, South Dakota, United States. The testbed for Experiment 1 at 1.5 km depth contained two open wells for injection and production and six instrumented monitoring wells surrounding the targeted stimulation zone. Four multi-step stimulation tests targeting hydraulic fracturing and nearly year-long ambient temperature and chilled water flow tests were performed in Experiment 1. The testbed for Experiments 2 and 3 was at 1.25 km depth and contained five open wells in an outwardly fanning five-spot pattern and two fans of well-instrumented monitoring wells surrounding the targeted stimulation zone. Experiment 2 targeted shear stimulation, and Experiment 3 targeted low-flow, high-flow, and oscillating pressure stimulation strategies. Hydraulic fracturing was successful in Experiments 1 and 3 in generating a connected system wherein injected water could be collected. However, the resulting flow was distributed dynamically, and not entirely collected at the anticipated production well. Thermal breakthrough was not observed in the production well, but that could have been masked by the Joule-Thomson effect. Shear stimulation in Experiment 2 did not occur - despite attempting to pressurize the fractures most likely to shear - because of the inability to inject water into a mostly-healed fracture, and the low shear-to-normal stress ratio. The EGS Collab experiments are described to provide a background for lessons learned on topics including induced seismicity, the correlation between seismicity and permeability, distributed and dynamic flow systems, thermoelastic and pressure effects, shear stimulation, local geology, thermal breakthrough, monitoring stimulation, grouting boreholes, modeling, and system management.

15 - GEOTHERMAL ENERGY↗

DOE OSTI2021

A predictive modeling tool for damage analysis and design of hydrogen storage composite pressure vessels

In this study, a predictive modeling tool is developed for damage analysis and design of hydrogen (H 2 ) storage composite pressure vessels. It integrates micromechanics of matrix cracking into a continuum damage mechanics (CDM) description for damage evolution, and three-dimensional (3D) finite element (FE) modeling of the vessel structural response. At the scale of the composite layer (mesoscale), the temperature-dependent stiffness reduction law in terms of the damage variable for transverse matrix cracking is computed using an Eshelby-Mori-Tanaka approach for the initial composite thermoelastic properties and a self-consistent model for the stiffness reduction as a function of the damage variable. While transverse matrix cracking obeying a damage evolution relation can progressively evolve from an initiation to a saturation state, fiber failure is predicted by a micromechanical fiber rupture criterion that accounts for the fiber strength and matrix stress. The implementation of this integrated multiscale modeling model into a 3D FE formulation enables damage analysis and design of H 2 storage composite pressure vessels. The developed tool is illustrated through 3D damage analyses of a cryogenically compressed H 2 storage vessel model subjected to thermomechanical loadings to investigate effects of the helical layer fiber orientation and loading scenario on damage development, vessel integrity and burst pressure.

08 HYDROGEN↗

DOE OSTI2023

Eulerian finite element implementations of a dislocation density-based continuum model

In Eulerian finite element simulations, the mesh moves relative to the material. After every change of position between the mesh and the material, the state variables are interpolated to the new mesh position, which is referred to as advection. Large strain crystal plasticity models are based on the multiplicative decomposition of the total deformation gradient. Further, the stress is evaluated as a function of the thermoelastic strain, temperature, and other state variables. Advection of tensor quantities, such as the strain, is coupled with possibly significant advection errors. In an effort to reduce the advection errors, we develop two rate forms of an established dislocation density-based continuum model. To that end, we replace the multiplicative decomposition of the deformation gradient with the additive decomposition of the velocity gradient, and define the stress rate instead of the total stress. The Eulerian implementation is compared with Lagrangian calculations, and two numerical examples with severe deformation levels are presented.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Extreme ultraviolet transient gratings: A tool for nanoscale photoacoustics

Collective lattice dynamics determine essential aspects of condensed matter, such as elastic and thermal properties. These exhibit strong dependence on the length-scale, reflecting the marked wavevector dependence of lattice excitations. The extreme ultraviolet transient grating (EUV TG) approach has demonstrated the potential of accessing a wavevector range corresponding to the 10s of nm length-scale, representing a spatial scale of the highest relevance for fundamental physics and forefront technology, previously inaccessible by optical TG and other inelastic scattering methods. In this manuscript we report on the capabilities of this technique in the context of probing thermoelastic properties of matter, both in the bulk and at the surface, as well as discussing future developments and practical considerations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Convergent laser beam shapes: Unveiling the dynamics of Laser-induced elastic waves in composite materials

Overcoming the low signal-to-noise ratio (SNR) in laser ultrasonic testing of composite materials remains a significant challenge. Current efforts focus on enhancing SNR by inserting more energy into the material through temporal and/or spatial modulation of the laser beam. However, potential SNR improvements through wave convergence and wave energy manipulation have been overlooked. This paper addresses this gap by demonstrating the convergence of different wave types to a designated point and by showing the feasibility of directing absorbed laser energy into a specific wave type through spatial modulation of the laser beam. To achieve this, mathematical expressions for the convergent laser beams are derived. Various laser beam profiles are then introduced to the thermoelastic equations and solved using the finite element method. The sample under investigation is a transversely isotropic unidirectional carbon fiber reinforced plastic, characterized by anisotropic thermal expansion coefficients and thermal conductivities. Results reveal pronounced convergence of the intended wave type at the center due to laser beam shaping. This study showcases the ability to direct absorbed laser energy toward a specific wave type through spatial modulation of the laser beam and highlights the role of material anisotropy in energy focusing.

composite materials↗