Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TENSILE STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Axial residual stresses in boron fibers

A method of measuring axial residual stresses in boron fibers is presented. With this method, the axial residual stress distribution as a function of radius is determined from the fiber surface to the core including the average residual stress in the core. Such measurements on boron on tungsten (B/W) fibers show that the residual stresses for 102, 142, 203, and 366 micron diam fibers are similar, being compressive at the surface and changing monotonically to a region of tensile stress within the boron. At approximately 25% of the original radius, the stress reaches a maximum tensile stress of about 860 MN sq m and then decreases to a compressive stress near the tungsten boride core. Data are presented for 203-micron diam B/W fibers that show annealing above 900 C reduces the residual stresses. A comparison between 102-micron diam B/W and boron on carbon (B/C) show that the residual stresses are similar in the outer regions of the fibers, but that large differences near and in the core are observed. Fracture of boron fibers is discussed.

Behrendt, D. R.↗

Effect of Stress States on Twinning Behavior in Twinning-Induced Plasticity Steel

The effects of stress state on the twin structures and kinetics in twinning-induced plasticity (TWIP) steel have been investigated to understand the twinning behaviors in more detail. Twinning behaviors of tension, compression, wire drawing, and caliber rolling were evaluated and compared using the EBSD technique, TEM measurement, and Schmid factor analysis. Twin structures, such as twin thickness, twin variant, twin shape, and twin kinetics were different with stress states. The specimen under compressive stress had wavy-shaped twins, less twin variant, lower twin thickness, and more twin volume fraction in comparison with the specimen under tensile stress. The different structures and kinetics of deformation twin with stress state were highly related to the grain rotation during plastic deformation. Under tensile stress, the grain rotation to <111> orientation, twinning-favored regions by Schmid factor analysis, encouraged the lateral growth of twins, more twin variants, and straight-type twins, while the grain rotation to <110> orientation under compressive stress suppressed the twin growth and twin variant and developed wavy-shaped twins. Drawn wire and caliber-rolled wire had both twin features under tensile and compressive stress states and higher twin volume fraction since complex stress state that combined tension and compression was applied in these processes. The hardness values were strongly related to the twin volume fraction with strain and stress state.

36 MATERIALS SCIENCE↗

Epitaxy and stress of MgO/GaAs(001) heterostructures

We report on the preparation of epitaxial MgO film on GaAs(001) substrates by molecular beam epitaxy at growth temperature of 20–200 °C. Reflection high energy electron diffraction, x-ray diffraction, and high resolution transmission electron microscopy reveal the growth of ordered crystalline cubic MgO(001) film at ∼200 °C with MgO(001)[100]|| GaAs(001)[100] and a 4 : 3 lattice registry. The surface of the MgO films, characterized by atomic force microscopy, exhibits a root mean square roughness of only 0.5 nm. In situ stress measurements reveal tensile stress as low as 1.7 GPa for a growth temperature of 200 °C in good agreement with the calculated residual misfit strain.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Behavior of MnO{sub 2}/Pb Nanocomposite

MnO{sub 2}/Pb nanocomposite was produced by solid-state accumulative roll-bonding (ARB) technique. Composites with different amounts of MnO{sub 2} were synthesized with the highest probable ARB cycles. The mechanical properties of composites were studied by tensile, microhardness and shear punch tests. It was observed that yield stress, tensile stress and elongation were improved by increasing the ARB cycles. On the other hand, increasing the amount of MnO{sub 2} up to 0.5 wt.% improved the mechanical properties of the composites. Tensile tests results revealed that the maximum tensile strength could be achieved in the composite containing 0.5 wt.% MnO{sub 2} after 10 passes (up to 4.35 times higher than control sample, Pb-10 pass). In comparison with Pb-10 pass, the hardness of 0.5 wt.% MnO{sub 2}/Pb nanocomposite was enhanced up to 7.5 times after 10 ARB passes. ARB process led to a proper distribution of MnO{sub 2} particles in Pb matrix with the mean size of less than 30 nm.

36 MATERIALS SCIENCE↗

Effect of deposition temperature of TiO{sub 2} on the piezoelectric property of PbTiO{sub 3} film grown by PbO gas phase reaction sputtering.

A 17 nm thick PbTiO{sub 3} (PTO) films were fabricated via PbO gas phase reaction with TiO{sub 2} starting layer in a sputtering chamber. The influence of deposition temperature of TiO{sub 2} on the piezoelectric properties of PTO thin films was investigated. The remnant piezoresponse of PTO films nonlinearly increased as a function of TiO{sub 2} deposition temperature, which is correlated with the increase in average grain diameter of PTO film. As grain size increases, the restriction on remnant piezoresponse imposed by the grain boundary via coupling between local strain and polarization becomes less pronounced, which results in the increase in remnant piezoresponse. Furthermore, we found that the vertical shift in piezoresponse hysteresis loops is closely related to the residual stress state. A strong correlation between the negative vertical shift and the residual tensile stress reveals that residual stress on the resulting PTO film contributed to the asymmetric piezoelectric property.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Strain Rate Sensitivity of Epoxy Resin in Tensile and Shear Loading

The mechanical response of E-862 and PR-520 resins is investigated in tensile and shear loadings. At both types of loading the resins are tested at strain rates of about 5x10(exp 5), 2, and 450 to 700 /s. In addition, dynamic shear modulus tests are carried out at various frequencies and temperatures, and tensile stress relaxation tests are conducted at room temperature. The results show that the toughened PR-520 resin can carry higher stresses than the untoughened E-862 resin. Strain rate has a significant effect on the response of both resins. In shear both resins show a ductile response with maximum stress that is increasing with strain rate. In tension a ductile response is observed at low strain rate (approx. 5x10(exp 5) /s), and brittle response is observed at the medium and high strain rates (2, and 700 /s). The hydrostatic component of the stress in the tensile tests causes premature failure in the E-862 resin. Localized deformation develops in the PR-520 resin when loaded in shear. An internal state variable constitutive model is proposed for modeling the response of the resins. The model includes a state variable that accounts for the effect of the hydrostatic component of the stress on the deformation.

Gilat, Amos↗

Effects of uniaxial stress on magnetoacoustic emission and magnetoacoustic responses in steel

Results of magnetoacoustic emission (MAE) and magnetoacoustic (MAC) measurements performed with an unembrittled HY-80 steel specimen are presented. The MAE measurements were obtained by applying an ac magnetic field of 20 Hz parallel to the uniaxial stress axis. The effects of tensile stress were shown to monotonically decrease the peak amplitude of the MAE burst, and they were consistent with the predicted trend based on the tensile stress-induced domain alignment. The effects of compressive stress were found to increase the peak amplitude of the MAE burst initially and to eventually decrease as the magnitude of compressive stress increased.

Namkung, M.↗

Strain control of composite superconductors to prevent degradation of superconducting magnets due to a quench: II. High-strength, laminated Ag-sheathed Bi-2223 tapes

In article I of this series, we described a spiral coil quench technique for probing the influence of the superconductor stress and strain state during normal operation on its margin to degradation during a quench and applied to a Bi-2212 round wire. Here we extend this technique to study the failure mechanisms and limits of high-strength Bi-2223 tapes experiencing a quench while carrying a large current in a high magnetic field. In contrast to Bi-2212 magnets made via a wind-and-react technique for which bending strains can be ignored, Bi-2223 magnets are made with a react-and-wind technique for which bending strain is significant. The critical tensile stress of Bi-2223 tapes (type HT-NX) decreases from >440 MPa for straight samples to 185 MPa after being bent to a diameter D of 50 mm. For HT-NX tapes with D = 50 mm, the quench degradation limit, measured using maximum allowable temperature during a quench T allowable , is greater than 300 K for axial tensile stress ${\sigma }_{a}$ < 94 MPa; it decreases with increasing tensile axial stress ${\sigma }_{a}$ nonlinearly, dropping to 230 K for ${\sigma }_{a}$ = 125 MPa. T allow able $({\sigma }_{a})$ experimental data at D = 50 mm is consistently predicted by a general strain model that assumes that quench degradation in NX/Bi-2223 is driven by axial tensile strain in Bi-2223 filaments exceeding the irreversible strain limit. The T allowable $({\sigma }_{a})$ is then predicted for various D including D = 80 mm important for NMR magnets. In conclusion, the given T allowable $(D,{\sigma }_{a})$ is easy to use and important for finding the balance between operation stress, and therefore magnetic field generation efficiency, and operation margin when designing a superconducting magnet using Bi-2223 tapes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Lattice parameter evolution in Pt nanoparticles during photo-thermally induced sintering and grain growth

An in-situ optical pump/x-ray probe technique has been used to study the size dependent lattice parameter of Pt nanoparticles subjected to picosecond duration optical laser pulses. The as-prepared Pt nanoparticles exhibited a contracted lattice parameter consistent with the response of an isolated elastic sphere to a compressive surface stress. During photo-thermally induced sintering and grain growth, however, the Pt lattice parameter did not evolve with the inverse particle size dependence predicted by simple surface stress models. Lastly, the observed behavior could be attributed to the combined effects of a compressive surface/interface stress and a tensile stress arising from intergranular material.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

A model to assess Zircaloy’s mechanical property changes following a transient beyond critical heat flux

Maintaining the integrity of nuclear fuel rods is essential for ensuring public health and safety in nuclear power generation. During reactor operation, this integrity is confirmed by demonstrating compliance with established regulatory acceptance criteria. For moderate-frequency events, such as limiting transients and anticipated operational occurrences (AOOs), the current fuel integrity criterion is based on preventing boiling transition. This criterion assumes that prevention of boiling transition will prevent excessive cladding heating and, thus, fuel failure during normal operations. While conservative, this approach places significant constraints on core design, fuel cycle economics, and a plant’s ability to perform major power uprates, leading to suboptimal fuel utilization and inefficient carbon-free energy production. A more efficient approach could be achieved by revising the failure criterion to a material-specific limit rather than strictly preventing the boiling transition, since boiling transition per se is not a cause of fuel cladding failure. Here, as a result, a new licensing framework based on material properties, termed time-at-temperature (t@T), is needed. This approach would allow for brief periods of post–critical heat flux operation during an AOO without compromising safety. Implementing the t@T licensing strategy requires a robust technical foundation in material properties, which must be established through comprehensive data collection on both unirradiated and irradiated fuel and cladding materials. This foundation would enable the development of a safety basis that ensures safe operation while providing greater flexibility and efficiency for reactor operation. This paper documents a thorough review of the available data to establish a baseline knowledge that can inform the development of cladding mechanical models, as well as identify experimental data gaps that need to be addressed in future research. Machine learning and data informatics were utilized to extract the importance of parameters on the t@T parameter. Industry tools were used to perform baseline analyses to define the relevant transient conditions for data analysis. The subsequent review successfully identified applicable experimental data, as well as sufficient data to evaluate changes in cladding mechanical properties following an AOO transient. Rather than developing new models, this work coupled existing irradiation annealing and recrystallization models to calculate changes in hardness, yield stress, and ultimate tensile stress following an AOO event. The findings from this review were summarized to highlight the experimental data needs required to fill remaining gaps and support the development of future t@T licensing methodologies.

Cladding performance↗

Thermal Stress Behavior of Micro- and Nano-Size Aluminum Films

In-situ observation of thermal stresses in thin films deposited on silicon substrate was made by X-ray and synchrotron radiation. Specimens prepared in this experiment were micro- and nano-size thin aluminum films with and without passivation film. The thickness of the film was 1 micrometer for micro-size films and 10, 20 and 50 nanometer for nano-size films. The stress measurement in micro-size films was made by X-ray radiation whereas the measurement of nano-size films was made by synchrotron radiation. Residual stress measurement revealed tensile stresses in all as-deposited films. Thermal stresses were measured in a series of heating- and cooling-stage. Thermal stress behavior of micro-size films revealed hysteresis loop during a heating and cooling process. The width of a hysteresis loop was larger in passivated film that unpassivated film. No hysteresis loops were observed in nano-size films with SiO{sub 2} passivation. Strengthning mechanism in thin films was discussed on a passivation film and a film thickness.

36 MATERIALS SCIENCE↗

Controllable strain-induced uniaxial anisotropy of Fe{sub 81}Ga{sub 19} films deposited on flexible bowed-substrates

We propose a convenient method to induce a uniaxial anisotropy in magnetostrictive Fe{sub 81}Ga{sub 19} films grown on flexible polyethylene terephthalate (PET) substrates by bending the substrate prior to deposition. A tensile/compressive stress is induced in the Fe{sub 81}Ga{sub 19} films when PET substrates are shaped from concave/convex to flat after deposition. The stressed Fe{sub 81}Ga{sub 19} films exhibit a significant uniaxial magnetic anisotropy due to the internal stress arising from changes in shape of PET substrates. The easy axis is along the tensile stress direction and the coercive field along easy axis is increased with increasing the internal tensile stress. The remanence of hard axis is decreased with increasing the compressive stress, while the coercive field is almost unchanged. A modified Stoner-Wohlfarth model with considering the distribution of easy axes in polycrystalline films is used to account for the magnetic properties tuned by the strain-controlled magnetoelastic anisotropy in flexible Fe{sub 81}Ga{sub 19} films. Our investigations provide a convenient way to induce uniaxial magnetic anisotropy, which is particularly important for fabricating flexible magnetoelectronic devices.

36 MATERIALS SCIENCE↗

Experimental Verification of Solidification Stress Theory

A research program is being conducted to develop a crack-free ceramic waste form (CWF) to be used for long term encasement of fission products and actinides resulting from processing spent nuclear fuel. Cracking usually occurs in the cooldown phase of the glass or ceramic formations. A crack-free formation should have more resistance to leaching than one with many cracks. In the research leading up to producing a CWF, a model was developed that proposes a permanent stress develops when the melt solidifies and that this stress can cause failure as the CWF nears room temperature. This paper reports on how the formation, CWF2, confirms the existence of this stress. The solidification stress is in addition to and of opposite sign of the thermal stress. Its derivation is reported on in Ref. 1. Cracking of the CWF would occur at low temperatures if solidification stress exists but at high temperatures if it doesn’t. If solidification stress occurs, then the cooldown rate during solidification should be reduced. If not, it should be reduced when the thermal stresses are highest. Recording cracking sounds confirm the existence of this solidification stress since cracking occurred during the low temperature phase of the cooldown. As a side purpose of this paper, a cooldown rate is proposed that should eliminate cracking in the next experiment, CWF3. CWF2 is a prototype vertical ceramic waste cylinder formed over a period of 10 days by heating a mixture of 75% zeolite, 25% glass frit in an argon atmosphere furnace through melting to 925 C and then cooling through solidification to room temperature. It is approximately 1 m high, 0.5 m in diameter, weighs about 400 kg, and is formed in a stainless steel can 0.5 cm thick. This cylinder developed many cracks on cooldown. At least 15 loud cracks were recorded over a period of 4 days at the end of cooldown when the temperatures were below 400 C. The CWF2 surface and centerline temperatures at mid height were measured which allowed the stress to be calculated. The timing of the cracks was compared to the time the calculated total stress exceeded the tensile stress limit and verified that the cause of the cracking was solidification stress and not thermal stress. Since the CWF is encased in a can in a furnace, the cracks cannot be easily observed but can be detected with sound measurements. Similarly, the stress cannot be measured but only estimated with analysis. Destructive examination of the CWF after cooldown was used to determine the pattern of the cracking which appeared to be initiated mainly in the inner region which is evidence the cracking is due to solidification stress.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Tidal reorientation and the fracturing of Jupiter's moon Europa

The lineaments on Europa are discussed in terms of the orientation of the lineaments relative to the tensile stress trajectories due to tidal distortions and to nonsynchronous rotation. The cracks are noticeable by their darker albedo compared to the presumed water ice surrounding them. The stress trajectories for tidal distortion of a thin elastic shell are superimposed on Mercator projection maps of the lineaments. It is shown that the lineaments are mainly oriented at high angles to the tensile stress trajectories that would be expected for regularly occurring nonsynchronous rotation, i.e., extensional fractures would appear. The reorientation motions which would cause the fractures are estimated. It is suggested that the fractures occur episodically to release stresses built up on the tensile surface of the crust during the continuous nonsynchronous rotation of Europa.

Mcewen, A. S.↗

High speed X-ray phase contrast imaging of energetic composites under dynamic compression

Fracture of crystals and subsequent frictional heating are associated with formation of hot spots in energetic composites such as polymer bonded explosives (PBXs). Traditional high speed optical imaging methods cannot be used to study the dynamic sub-surface deformation and fracture behavior of such materials due to their opaque nature. In this study, high speed synchrotron X-ray experiments are conducted to visualize the in situ deformation and fracture mechanisms in PBXs manufactured using octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) crystals and hydroxyl-terminated polybutadiene (HTPB) binder. A modified Kolsky bar apparatus was used to apply controlled dynamic compression on the PBX specimens, and a high speed synchrotron X-ray phase contrast imaging (PCI) setup was used to record the in situ deformation and failure in the specimens. The experiments show that synchrotron X-ray PCI provides a sufficient contrast between the HMX crystals and the doped binder, even at ultrafast recording rates. Under dynamic compression, most of the cracking in the crystals was observed to be due to the tensile stress generated by the diametral compression applied from the contacts between the crystals. Tensile stress driven cracking was also observed for some of the crystals due to the transverse deformation of the binder and superior bonding between the crystal and the binder. In conclusion, the obtained results are vital to develop improved understanding and to validate the macroscopic and mesoscopic numerical models for energetic composites so that eventually hot spot formation can be predicted.

36 MATERIALS SCIENCE↗

High temperature low cycle fatigue mechanisms for nickel base and a copper base alloy

Damage mechanisms were studied in Rene' 95 and NARloy Z, using optical, scanning and transmission in microscopy. In necklace Rene' 95, crack initiation was mainly associated with cracking of surface MC carbides, except for hold time tests at higher strain ranges where initiation was associated more with a grain boundary mechanism. A mixed mode of propagation with a faceted fracture morphology was typical for all cycle characters. The dependence of life on maximum tensile stress can be demonstrated by the data falling onto three lines corresponding to the three tensile hold times, in the life against maximum tensile stress plot. In NARloy Z, crack initiation was always at the grain boundaries. The mode of crack propagation depended on the cycle character. The life decreased with decreasing strain rate and with tensile holds. In terms of damage mode, different life prediction laws may be applicable to different cycle characters.

Shih, C. I.↗

An improved three-point bending test method for the investigation of nanosecond laser dicing of ultrathin Si dies with Cu stabilization layer

Highlights: • A selective chemical etching method has been developed for removal of metallization layers on ultrathin Si dies for three-point bending test. • The complex elastoplastic stress distribution in the die is simplified to an elastic stress distribution. • The die sidewall fracture strength can be determined using the standard three-point bending tensile stress equation. • The characteristic fracture strengths of ultrathin Si dies were correlated to the laser-induced microstructures of the die sidewall. - Abstract: The sidewall fracture strength of ultrathin Si dies with frontside and backside metallization layers cannot be determined directly from three-point bending (3PB) test. The complex 3PB elastoplastic stress distribution makes it difficult to determine the die sidewall fracture strength by analytical method or finite element analysis due to various theoretical and practical constraints. In this work, a selective chemical etching method has been developed for complete removal of the frontside and backside metallization layers on the ultrathin die without affecting the critical microstructure and strength of the die sidewall induced by laser dicing. By removing all the metallization layers on the die, the complex 3PB elastoplastic stress distribution is simplified to an elastic stress distribution. This enables a straightforward calculation of the die sidewall fracture strength using the standard 3PB tensile stress equation for a homogeneous linear elastic material with a rectangular cross section. Two chemical etchants were evaluated and found to be suitable but FeCl{sub 3} is preferred because of the much faster etching time. With this improved 3PB test method, the effect of nanosecond laser dicing on ultrathin Si dies with backside Cu layer was investigated. The die frontside and backside characteristic fracture strengths of ultrathin Si dies with varying backside Cu thickness were determined and correlated to TEM analyses of the compositions and microstructures at the fracture origins.

36 MATERIALS SCIENCE↗

Effect of peak stress and tensile strain-rate on spall in tantalum

Materials subjected to dynamic environments experience a complex and wide range of stress, strain, and strain-rate conditions. To have confidence in material models, an accurate, predictive capability is required. In this study, we present a series of flyer-plate impact tests on well characterized, high purity tantalum. The shock-waves generated at impact release from the free-surfaces, reflect, and interact to produce incipient spall fracture. By varying the flyer-plate material and impact velocity, both the peak stress and the strain-rate in the samples were controlled independently. Velocimetry was used on the rear free-surface of the samples to measure the shock-response and the spall strength. While this measurement provided the same spall strength for all cases, at approximately 5.1 GPa, when the samples were sectioned during post-mortem, the quantity and distribution of internal damage was markedly different. For the high-strain rate cases, voids remained small and isolated, whereas in the lower strain-rate experiments, the spall damage was far more localized, with a well-defined continuous spall plane. With the use of hydrocode simulations, this was discovered to result from how the different release rates affect the interaction volume inside the sample. Here, these results highlight the importance of careful sample recovery, and the risks of relying solely on free-surface velocity measurements.

36 MATERIALS SCIENCE↗