SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
In the study of stress-strain relationships in silicon ribbon, numerous solutions were calculated for stresses, strain rates, and dislocation densities through the use of the Sumino model. It was concluded that many cases of failure of computer solutions to converge are analytical manifestations of shear bands (Luder's band) observed in experiments.
As part of a long-term attempt to learn how the climatic and tectonic signal interact to shape a steady state mountain monitored displacement of a markers in SE termination and also near the summit of a small viscous salt fountain extruding onto the Central plateau of Iran. The marker displacements relate to the first InSAR interferograms of salt extrusion (980913 to 990620) calculated Earth tides, winds, air pressures and temperatures. In the first documented staking exercise, hammered wooden stakes vertically through the surgical marl (c. 1 Ocm deep) onto the top of crystalline salt. These stakes installed in an irregular array elongate E-W along the c.50 m high cliff marking the effective SE terminus of the glacier at Qum Kuh(Centra1 Iran) ,just to the E of a NE trending river cliff about 40 m high. We merely measured the distances between pairs of stakes with known azimuth about 2 m apart to calculate sub horizontal strain in a small part of Qum Kuh. Stakes moved and micro strains for up to 46 pairs of stakes (p strain= ((lengthl-length2)/1engthl) x 10-1) was calculated for each seven stake epochs and plotted against their azimuth on simplified array maps. The data fit well the sine curves cxpected of the maximum and minimum strain ellipses. The first documented stakes located on the SE where the InSAR image show -1 1 to 0 mm pink to purple, 0 to lOmm purple to blue, and show high activity of salt in low activity area of the InSAR image (980913 to 990620).Short term micro strains of stake tie lines record anisotropic expansions due to heating and contraction due to cooling. All epochs changed between 7 to 1 17 days (990928 to000 1 16), showed 200 to 400 micro strain lengthening and shortening. The contraction and extension existed in each epoch, but the final strain was extension in E-W in Epoch land 6, contraction in E-W direction during epochs 2-3-4-5 and 7. The second pair of stakes hammered about 20 cm deep into the deep soils(more than 1 m) , near summit, where the colors change between 19 to 29mm in InSAR image(9809 13 to 990620). Additional information is included in the original abstract.
Current capabilities of moire interferometry are described. Several examples illustrate this whole-field optical technique for measurements of in-plane displacements. Sensitivity corresponds to moire measurements with gratings of 2400 lines/mm. The examples are taken from studies of composite members, material anomalies, plasticity, joints, micromechanics and strain concentrations. The abundance of high-sensitivity displacement information permits calculation of normal strains and shear strains in the field, including critical zones of very high gradients.
Primitiveasteroids, most of which are located in the outer belt and Jupiter’s Trojan clouds, provide information related to the origin and evolution of the solar system and the conditions in which the solar nebula was formed. These asteroids are widely thought to be the origin of the least-altered car-bonaceous chondrite that allow us to put crucial con-straints on the current dynamical and thermal theories of the formation and evolution of the early solar sys-tem. The nature of surface composition of large and low-albedo asteroids, like (1) Ceres, (10) Hygiea and (52) Europa, is still under intense debate and different interpretations have beenput forth to explain the ab-sorption features in these objects (e.g.,[1, 2, 3,4,5,6]). Laboratory and spectroscopic experiments on me-teorites that represent all nine carbonaceous chondrite types also found no spectral matches for these large asteroids (e.g.,[7]). Previous studies of asteroid Ceres (the largest primitive asteroid in the solar system) have been conducted to constrain and estimate its surface composition (e.g., [2, 5]). Using linear mixing,[2]found hydroxide brucite, serpentines, and carbonates, to be consistent with Ceres’ ground-based spectra.[5]estimated the surface composition of Ceres and found evidence of widespread NH3-phyllosilicates across its surface using best-fit solutions to Dawn’s NIR spectra. The presence of NH3-phyllosilicates implies that mate-rial from the outer solar system was incorporated into large primitive asteroids, either during their formation at great heliocentric distance or by incorporation of material transported into the Main Belt region. Here we presentnew largeand primitive asteroidsthat share the same spectral similaritieswith the largest asteroid in the solar system, Ceres.We also present the context of these new observations in terms oftheirthermal and dynamicalevolution.Large Primitive Asteroids: Dynamical and Thermal Context:Orbital Distribution of LargePrimitiveAsteroids: Constraining the mineralogy and surface composition of large primitive asteroids will place crucial con-straints on existing dynamical and thermal theories of the formation of the early solar system. We identified several additional asteroids in the Europa-like group in addition to asteroids Europa, Euphrosyne, and Patien-tia, that wereidentified in [8]using NASA IRTFtele-scope (e.g.,Figure 1). These new asteroids along with the already-observed Ceres-and Europa-like group members are localized in the 2.8 < a < 3.4 AU region and characterized by larger sizes, showing an interest-ing orbital distribution (Figure 2). Ceres-likeand Eu-ropa-like groups, which include the largest asteroids in the solar system, show an interesting orbital distribu-tion. These groups are located in the 2.6 < a < 3.6 AU region that contains the snow-line. The snow-line’s location may have been driftedinwards due to the disk’s cooling and evolution[9,10]. Recent dynamical models[11,12]suggested that a substantial fraction of primitive asteroids originated between or beyond the giant planets (a > 5 AU), where water ice would have been stable, and then implanted in the outer Main Belt region because of the giant planets’ growth.Figure 1. Two asteroids, 94 Aurora and 423 Diotima, showing spectra similar to asteroids (1)Ceres and (52)Europa.Thermal modeling and evolution of primitive aster-oids:Primitive water-rich asteroids are thought to be originally composed of mixtures of anhydrous materi-als and water ice that waslater melted by heating sources such as the decay of 26Al, reacting with anhy-drous materials to form H2O/OH-rich minerals. Calcu-lations of the evolution of the temperature and struc-ture of icy planetesimals were performedusing a 1D finite differences thermal evolution model[13, 14] for 26Al-heated planetesimals. In particular, thermally activated compaction due to hot pressing of bodies with an initially unconsolidated porous structure is included. An ice-rich initial composition that leads to a material dominated by phyllosilicates upon aqueous alteration (with 25 vol% H2O and a rock fraction that contains 85 vol% phyllosilicates and 15 vol% olivine upon aque-ous alteration, similar to CIand CM chondrites) was assumed. Atypical initial porosity of 40%[15] is re-duced following the change of the strain rate that is calculated as Voigt approximation from the strain rates of components[16]. Material properties (thermal con-ductivity, density, heat capacity, etc.) correspond to the composition assumed and are adjusted with tempera-ture and porosity. Melting of the water ice as well as water-rock separation are included[14]. Both short-and long-lived radionuclides are consideredas heat sources. Figure 3 shows the maximum temperature calculated as a function of radius and accretion time. A variety of internal structures is obtained, ranging from primordial (no melting of water ice) over partially melted or partially differentiated (melting of water ice, hydration, formation of a rocky core and water ocean below an undifferentiated layer) to completely differ-entiated ones (rocky core, water mantle, Enceladus-like case). The heating and differentiation of planetesi-mals is determined by the availability of 26Al, i.e., by the accretion time t0 relative to the formation of the calcium-aluminum-rich inclusions (CAIs), such that maximum temperatures and structures vary stronglyfor t0< 6 Myr rel. to CAIs. However, for a later accre-tion only the size of the body determines its maximum tempera-ture and structure due to the nearly constant heating by long-lived radionuclides. Average densities of Ceres-and Europa-like group membersimply high-ly porous interiors and, consequently, relatively late accretion at t0> 3 Myr rel. to CAIs with a maximum temperature of < 600 K (Figure3)
Procedures are presented for expressing the Strainrange Partitioning (SRP) method for creep fatigue life prediction in terms of total strain range. Inelastic and elastic strain-range - life relations are summed to give total strain-range - life relations. The life components due to inelastic strains are dealt with using conventional SRP procedures while the life components due to elastic strains are expressed as families of time-dependent terms for each type of SRP cycle. Cyclic constitutive material behavior plays an important role in establishing the elastic strain-range - life relations as well as the partitioning of the inelastic strains. To apply the approach, however, it is not necessary to have to determine the magnitude of the inelastic strain range. The total strain SRP approach is evaluated and verified using two nickel base superalloys, AF2-1DA and Rene 95. Excellent agreement is demonstrated between observed and predicted cyclic lifetimes with 70 to 80 percent of the predicted lives falling within factors of two of the observed lives. The total strain-range SRP approach should be of considerable practical value to designers who are faced with creep-fatigue problems for which the inelastic strains cannot be calculated with sufficient accuracy to make reliable life predictions by the conventional inelastic strain range SRP approach.
Procedures are presented for expressing the Strainrange Partitioning (SRP) method for creep fatigue life prediction in terms of total strain range. Inelastic and elastic strain-range - life relations are summed to give total strain-range - life relations. The life components due to inelastic strains are dealt with using conventional SRP procedures while the life components due to elastic strains are expressed as families of time-dependent terms for each type of SRP cycle. Cyclic constitutive material behavior plays an important role in establishing the elastic strain-range life relations as well as the partitioning of the inelastic strains. To apply the approach, however, it is not necessary to have to determine the magnitude of the inelastic strain range. The total strain SRP approach is evaluated and verified using two nickel base superalloys, AF2-1DA and Rene 95. Excellent agreement is demonstrated between observed and predicted cyclic lifetimes with 70 to 80 percent of the predicted lives falling within factors of two of the observed lives. The total strain-range SRP approach should be of considerable practical value to designers who are faced with creep-fatigue problems for which the inelastic strains cannot be calculated with sufficient accuracy to make reliable life predictions by the conventional inelastic strain range SRP approach.
In new method of determining load on specimen, direction of stress wave propagation measured by array of acoustic sensors attached to specimen. Responses of sensors analyzed by strain-energy-density calculations to calculate load. Change in anisotropy of elasticity caused by applied load and corresponding induced strain. Is means to monitor applied load corresponding to measurable shift in direction of propagation of stress wave. Monitoring device based on this method made integral part of airframe in which unidirectional section of structure, such as spar cap or longeron, carries primary load.
An experimental program was conducted to determine the feasibility of using subscale plastic models to determine the response of full-scale aerospace structural components to impulsive, pyrotechnic loadings. A monocoque cylinder was impulsively loaded around the circumference of one end, causing a compressive stress wave to propagate in the axial direction. The resulting structural responses of two configurations of the cylinder (with and without a cutout) were recorded by photoelasticity, strain gages, and accelerometers. A maximum dynamic stress concentration was photoelastically determined and the accelerations calculated from strain-gage data were in good agreement with those recorded by accelerometers. It is concluded that reliable, quantitative structural response data can be obtained by the experimental techniques described in this report.
A computer program was developed to take a NASTRAN output file from a normal modes analysis and calculate the modal strain energies of selected elements. The FORTRAN program can determine the modal strain energies for CROD, CBAR, CELAS, CTRMEM, CQDMEM2, and CSHEAR elements. Modal strain energies are useful in estimating damping in structures.
A computer program called TFLIFE is described which can be used to predict the thermal fatigue life of metals and structural components from conventional metal properties. This program is used as a subroutine with a main program supplied by the user. The main program calculates input cycles of temperature and total strain for TFLIFE which then calculates a stress cycle, creep and plastic strain damage, and cyclic life. A unique feature of TFLIFE is that it calculates lives according to several different failure criteria for the same input data. These criteria are surface crack initiation, interior crack initiation, and complete fracture of both unnotched and notched fatigue specimens. Results are presented for two typical problems: thermal-mechanical fatigue of bar specimens of the tantalum alloy T-111 and thermal-stress fatigue of wedge specimens of the nickel alloy B-1900. The computer program is now ready for more extensive evaluation on structural components and additional laboratory specimens.
NASA Langley Research Center is developing instrumentation based upon principles of Optical Frequency-Domain Reflectometry (OFDR) for the provision of large-scale, dense distribution of strain sensors using fiber optics embedded with Bragg gratings. Fiber Optic Bragg Grating technology enables the distribution of thousands of sensors immune to moisture and electromagnetic interference with negligible weight penalty. At Langley, this technology provides a key component for research and development relevant to comprehensive aerospace vehicle structural health monitoring. A prototype system is under development that includes hardware and software necessary for the acquisition of data from an optical network and conversion of the data into strain measurements. This report documents the steps taken to verify the software that implements the algorithm for calculating the fiber strain. Brief descriptions of the strain measurement system and the test article are given. The scope of this report is the verification of software implementations as compared to a reference model. The algorithm will be detailed along with comparison results.
Strain-energy release rates are often used to predict when delamination growth will occur in laminates under compression. Because of the inherently high computational cost of performing such analyses, less rigorous analyses such as thin-film plate analysis were used. The assumptions imposed by plate theory restrict the analysis to the calculation of total strain energy, G(sub t). The objective is to determine the accuracy of thin-film plate analysis by comparing the distribution of G(sub t) calculated using fully three dimensional (3D), thin-film 3D, and thin-film plate analyses. Thin-film 3D analysis is the same as thin-film plate analysis, except 3D analysis is used to model the sublaminate. The 3D stress analyses were performed using the finite element program NONLIN3D. The plate analysis results were obtained from published data, which used STAGS. Strain-energy release rates were calculated using variations of the virtual crack closure technique. The results demonstrate that thin-film plate analysis can predict the distribution of G(sub t) quite well, at least for the configurations considered. Also, these results verify the accuracy of the strain-energy release rate procedure for plate analysis.
CLFE2D is a two dimensional generalized plane strain finite element code, using a linear, four node, general quadrilateral, isoparametric element. The program is developed to calculate the displacements, strains, stresses, and strain energy densities in a finite width composite laminate. CLFE2D offers any combination of the following load types: nodal displacements, nodal forces, uniform normal strain, or hygrothermal. The program allows the user to input one set of three dimensional orthotropic material properties. The user can then specify the angle of material principal orientation for each element in the mesh. Output includes displacements, stresses, strains and strain densities at points selected by the user. An option is also available to plot the underformed and deformed finite element meshes.
Aircraft design has been progressing toward reduced structural weight to improve fuel efficiency, increase performance, and reduce cost. Lightweight aircraft structures are more flexible than conventional designs and require new design considerations. Intelligent sensing allows for enhanced control and monitoring of aircraft, which enables increased structurally efficiency. The NASA Dryden Flight Research Center (DFRC) has developed an instrumentation system and analysis techniques that combine to make distributed structural measurements practical for lightweight vehicles. Dryden's Fiber Optic Strain Sensing (FOSS) technology enables a multitude of lightweight, distributed surface strain measurements. The analysis techniques, referred to as the Displacement Transfer Functions (DTF) and Load Transfer Functions (LTF), use surface strain values to calculate structural deflections and operational loads. The combined system is useful for real-time monitoring of aeroelastic structures, along with many other applications. This paper describes how the capabilities of the measurement system were demonstrated using subscale test articles that represent simple aircraft structures. Empirical FOSS strain data were used within the DTF to calculate the displacement of the article and within the LTF to calculate bending moments due to loads acting on the article. The results of the tests, accuracy of the measurements, and a sensitivity analysis are presented.
A recent variational mechanics analysis of microcracking damage in cross-ply laminates of the form /(S)/90n/s, where (S) is any orthotropic sublaminate much stiffer than /90n/, has been extended to account for the presence of delaminations emanating from the tips of microcracks in the /90 2n/T sublaminate. The new two-dimensional stress analysis is used to calculate the total strain energy, effective modulus, and longitudinal thermal expansion coefficient for a laminate having microcracks and delaminations. These results are used to calculate the energy release rate for the initiation and growth of a delamination induced by a matrix microcrack. At low crack densities, /(S)/90n/s laminates are expected to fail by microcracking and to show little or no delamination. At some critical crack density, which is a function of laminate structure and material properties, the energy release rate for delamination exceeds that for microcracking and delamination is predicted to dominate over microcracking. A quasi-three-dimensional model is used to predict the propagation of arbitrarily shaped delamination fronts. All predictions agree with experimental observations.
Ten 24S-T alclad cylinders of 20-inch diameter, 45- or 58-inch length, and 0.012-inch wall thickness, reinforced with 24S-T aluminum alloy stringers and rings were tested in pure bending. In the middle of the compression side of the cylinders there was a cutout extending over 19 inches in the longitudinal direction, and over an angle of 45 degrees, 90 degrees, or 135 degrees in the circumferential direction. The strain in the stringers and in the sheet covering was measured with metal electric strain gages. The stress distribution in the cylinders deviate considerably from the linear law valid for cylinders without a cutout. The maximum strain measured was about four-thirds of the value calculated from the Mc/I formula when I was taken as the moment of inertia of the cross section of the portion of the cylinder where the cutout was situated. A diagram is presented containing the strain factors defined as the ratios of measured strain to strain calculated with the Mc/I formula. All the 10 cylinders tested failed in general instability. Two symmetric and one antisymmetric pattern of buckling were observed and the buckling load appeared to be independent of the method of manufacture and the length of the cylinder. The buckling load of the cylinders having cutouts extending over 45 degrees, 90 degrees, and 135 degrees was 66, 47, and 31 percent, respectively, of the buckling load of the cylinder without a cutout.
Atomic stresses were calculated for carbon nanotubes under strain conditions. Graphitic tubules with radii ranging from approximately 2 to 11 Angstroms and two different tubule structures with varying atomic orientations were included in the calculations. Elongations and contractions were applied in the axial direction and atomic stress values were calculated for infinitely long tubules. The calculations were carried out using Brenner's function which was developed for carbon species. Results indicate that the stress is tensile in the radial direction while it is compressive in the tangential direction. Variations in stress values in the direction of the cylindrical aids were investigated as a function of applied strain. Furthermore, using the stress-strain curve (calculated based on atomic considerations), the values of Young's modulus and Poisson's ratio for nanotubules were also estimated.
Fracture-mechanics approach applied to delamination failures. Report presents fracture-mechanics approach to analyzing, characterizing, and designing against delamination. In study, examples of delamination problems illustrated wherein strain-energy-release rate associated with growth of delamination useful generic parameter, independent of thickness, layup, and source of delamination, for characterization of failure by delamination. Several techniques for calculation of strain-energy-release rates for delaminations from variety of sources outlined. Technique for quantification of durability due to cyclic loading presented.