Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SULFURIC ACID”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

H2O-H2SO4 system in Venus' clouds and OCS, CO, and H2SO4 profiles in Venus' troposphere

A coupled problem of diffusion and condensation is solved for the H2SO4-H2O system in Venus' cloud layer. The position of the lower cloud boundary and profiles of the H2O and H2SO4 vapor mixing ratios and of the H2O/H2SO4 ratio of sulfuric acid aerosol and its flux are calculated as functions of the column photochemical production rate of sulfuric acid, Phi(sub H2SO4). Variations of the lower cloud boundary are considered. Our basic model, which is constrained to yield f(sub H2O) (30 km) = 30 ppm (Pollack et al. 1993), predicts the position of the lower cloud boundary at 48.4 km coinciding with the mean Pioneer Venus value, the peak H2SO4 mixing ratio of 5.4 ppm, and the H2SO4 production rate Phi(sub H2SO4) = 2.2 x 10(exp 12)/sq cm/s. The sulfur to sulfuric acid mass flux ratio in the clouds is 1:27 in this model, and the mass loading ratio may be larger than this value if sulfur particles are smaller than those of sulfuric acid. The model suggests that the extinction coefficient of sulfuric acid particles with radius 3.7 micrometers (mode 3) is equal to 0.3/km in the middle cloud layer. The downward flux of CO is equal to 1.7 x 10(exp 12)/sq cm/s in this model. Our second model, which is constrained to yield f(sub H2O) = 10 ppm at the lower cloud boundary, close to the value measured by the Magellan radiooccultations, predicts the position of this boundary to be at 46.5 km, which agrees with the Magellan data; f(sub H2O) (30 km) = 90 ppm, close to the data of Moroz et al. (1983) at this altitude; Phi(sub H2SO4) = 6.4 x 10(exp 12)/sq cm/s; and Phi(sub co) = 4.2 x 10(exp 12)/sq cm/s. The S/H2SO4 flux mass ratio is 1:18, and the extinction coefficient of the mode 3 sulfuric acid particles is equal to 0.9 km in the middle cloud layer. A strong gradient of the H2SO4 vapor mixing ratio near the bottom of the cloud layer drives a large upward flux of H2SO4, which condenses and forms the excessive downward flux of liquid sulfuric acid, which is larger by a factor of 4-7 than the flux in the middle cloud layer. This is the mechanism of formation of the lower cloud layer. Variations of the lower cloud layer are discussed. Our modeling of the OCS and CO profiles in the lower atmosphere measured by Pollack et al. (1993) provides a reasonable explanation of these data and shows that the rate coefficient of the reaction SO3 + CO yields CO2 + SO2 is equal to 10(exp -11) exp(-(13,100 +/- 1000)/T) cc/s. The main channel of the reaction between SO3 and OCS is CO2 + (SO)2, and its rate coefficient is equal to 10(exp -11) exp(-(8900 +/- 500)/T) cc/s. In the conditions of Venus' lower atmosphere, (SO)2 is removed by the reaction (SO)2 + OCS yields CO + S2 + SO2. The model predicts an OCS mixing ratio of 28 ppm near the surface.

Krasnopolsky, V. A.↗
NASA NTRS1979

Oxides of nitrogen and the clouds of Venus

Nitric oxide may be produced in the atmosphere of Venus by lightning storms in the clouds. The paper suggests that the odd nitrogen thus formed may play an important part in the chemistry of the clouds. Specifically, production rates for NO2 in the limiting case of high NO concentrations are estimated. If the NO density is high, it is suggested that NO2 may catalyse the production of sulfuric acid aerosol from sulfur dioxide and water vapor, and may also form nitrogen-sulfur compounds such as nitrosyl sulfuric acid, NOHSO4. The large partricles seen by the Pioneer Venus sounder probe may contain considerable quantities of NOHSO4. If this is the case, odd nitrogen must be present in the atmosphere in at least a parts-per-million mixing ratio.

Watson, A. J.↗
NASA NTRS2021

Hypogenic Karst of the Great Basin

Discoveries in the 1980s greatly expanded speleologists’ understanding of therole that hypogenic groundwater flow can play developingcaves at depth. Ascending groundwater charged with carbon dioxide and,especially,hydrogen sulfide,can readily dissolve carbonate bedrock just below and above the water table. Sulfuric acid speleogenesis, in which anoxic, rising, sulfidic groundwater mixes with oxygenated cave atmosphere to form aggressive sulfuric acid (H2SO4), formed spectacular caves in CarlsbadCaverns National Park. Cueva de Villa Luz in Mexico provides an aggressively active example of sulfuric acid speleogenesisprocesses, and the Frasassi Caves in Italy preserve the results of sulfuric acid speleogenesis in its upper levels while sulfidic groundwater currently enlarges cave passages in the lower levels. Manycaves in east-central Nevada and western Utah are products of hypogenic speleogenesis and formed before the current topography fully developed. Wet climate during the late Neogeneand Pleistocene brought extensive meteoric infiltration into the caves and calcite speleothems (e.g., stalactites, stalagmites, shields) coat the walls and floors of the caves, concealing evidence of the earlier hypogenic stage. However, by studying the speleogenetic features in well-established sulfuric acid speleogenesis caves, evidence ofhypogenic, probably sulfidic, speleogenesis inmany Great Basin caves can be teased out.Compelling evidence of hypogenicspeleogenesis in these cavesinclude folia, mammillaries, bubble trails, cupolas, and metatyuyamunite. Sulfuric acid speleogenesis signsinclude hollowcoralloidstalagmites,trays, gypsum crust, pseudoscallops, rills, and acid pool notches. Lehman Caves is particularly informative as a low-permeability capstone protected about half of the cave from significant meteoric infiltration, preserving early speleogeneticfeatures.

Louise D Hose↗
NASA NTRS2011

Comparison of Four Strong Acids on the Precipitation Potential of Gypsum in Brines During Distillation of Pretreated, Augmented Urine

Two batches of nominally pretreated and augmented urine were prepared with the baseline pretreatment formulation of sulfuric acid and chromium trioxide. The urine was augmented with inorganic salts and organic compounds in order to simulate a urinary ionic concentrations representing the upper 95 percentile on orbit. Three strong mineral acids: phosphoric, hydrochloric, and nitric acid, were substituted for the sulfuric acid for comparison to the baseline sulfuric acid pretreatment formulation. Three concentrations of oxidizer in the pretreatment formulation were also tested. Pretreated urine was distilled to 85% water recovery to determine the effect of each acid and its conjugate base on the precipitation of minerals during distillation. The brines were analyzed for calcium and sulfate ion, total, volatile, and fixed suspended solids. Test results verified that substitution of phosphoric, hydrochloric, or nitric acids for sulfuric acid would prevent the precipitation of gypsum up to 85% recovery from pretreated urine representing the upper 95 percentile calcium concentration on orbit.

Muirhead, Dean↗
NASA NTRS1985

Determination of the viscosity number of thermoplastics in dilute solution; polyamides (PA)

This West German Standard presents a test used to determine the viscosity number of polyamides and copolyamides which are easily diluted in sulfuric acid, and for other polyamides which are less easily diluted in sulfuric acid, and which are diluted in m-cresol. As formic acid is often used in industry instead of sulfuric acid, this solvent is also presented as an alternative, however, sulfuric acid is preferred because of the thermodynamic solubility characteristics of the polyamides and the handling safety. In addition, it is shown which solvent should be used for each polyamide. Finally, determinations concerning the preparation of the samples are presented. Using the viscosity number, a determination of the molar mass of the polyamides is possible.

Source record↗
NASA NTRS1987

Wear of iron and nickel in corrosive liquid environments

Friction and wear behavior of Fe and Ni sliding on aluminum oxide in aerated sulfuric acid and hydrochloric acid were investigated. The results show that the concentration of acid is an important factor in controlling the metal loss caused by wear corrosion processes in the acids. At very dilute acid concentration (10 to the -4 N), Fe behaves differently from Ni. Fe develops a soft, friable deposit, while Ni develops no corrosion layer. The formation and removal of the corrosion deposit on Fe resulted in high metal loss and coefficient of friction, as compared to the relatively low metal loss and coefficient of friction observed for Ni. At slightly higher acid concentration (10 to the -3 and 10 to the -2 N), no corrosion products were produced on both Fe and Ni. Wear of Fe and Ni was generally at a minimum. At higher acid concentration (10 to the -1 N and above), loss of Fe and Ni increased as the acid concentration increased. In sulfuric acid the maximum loss of both Fe and Ni was at 7.5 N (30%) concentration, and the metal losses of both Fe and Ni dropped markedly at 15 N (50%) and above. In hydrochloric acid, however, the Fe loss continued to increase with the increase of acid concentration, and the maximum Fe loss occurred in the most concentrated acid (12.1 N, 37%). There were variations in loss with Ni from specimen to specimen examined in hydrochloric acids (10 to the -1 N and above). The coefficient of friction for Ni increased slightly with an increase in acid concentration up to 10 to the -2 N. When corrosion started to dominate in the wear-corrosion process, the coefficient of friction decreased in both sulfuric and hydrochloric acids at 10 to the -1 N and above.

Miyoshi, Kazuhisa↗
NASA NTRS1988

Wear of iron and nickel in corrosive liquid environments

Friction and wear behavior of Fe and Ni sliding on aluminum oxide in aerated sulfuric acid and hydrochloric acid were investigated. The results show that the concentration of acid is an important factor in controlling the metal loss caused by wear corrosion processes in the acids. At very dilute acid concentration (10 to the -4 N), Fe behaves differently from Ni. Fe develops a soft, friable deposit, while Ni develops no corrosion layer. The formation and removal of the corrosion deposit on Fe resulted in high metal loss and coefficient of friction, as compared to the relatively low metal loss and coefficient of friction observed for Ni. At slightly higher acid concentration (10 to the -3 and 10 to the -2 N), no corrosion products were produced on both Fe and Ni. Wear of Fe and Ni was generally at a minimum. At higher acid concentration (10 to the -1 N and above), loss of Fe and Ni increased as the acid concentration increased. In sulfuric acid the maximum loss of both Fe and Ni was at 7.5 N (30 percent) concentration, and the metal losses of both Fe and Ni dropped markedly at 15 N (50 percent) and above. In hydrochloric acid, however, the Fe loss continued to increase with the increase of acid concentration, and the maximum Fe loss occurred in the most concentrated acid (12.1 N, 37 percent). There were variations in loss with Ni from specimen to specimen examined in hydrochloric acids (10 to the -1 N and above). The coefficient of friction for Ni increased slightly with an increase in acid concentration up to 10 to the -2 N. When corrosion started to dominate in the wear-corrosion process, the coefficient of friction decreased in both sulfuric and hydrochloric acids at 10 to the -1 N and above.

Miyoshi, Kazuhisa↗
NASA NTRS1997

A New Parameterization of H2SO4/H2O Aerosol Composition: Atmospheric Implications

Recent results from a thermodynamic model of aqueous sulfuric acid are used to derive a new parameterization for the variation of sulfuric acid aerosol composition with temperature and relative humidity. This formulation is valid for relative humidities above 1 % in the temperature range of 185 to 260 K. An expression for calculating the vapor pressure of supercooled liquid water, consistent with the sulfuric acid model, is also presented. We show that the Steele and Hamill [1981] formulation underestimates the water partial pressure over aqueous H2SOI solutions by up to 12% at low temperatures. This difference results in a corresponding underestimate of the H2SO4 concentration in the aerosol by about 6 % of the weight percent at approximately 190 K. In addition, the relation commonly used for estimating the vapor pressure of H2O over supercooled liquid water differs by up to 10 % from our derived expression. The combined error can result in a 20 % underestimation of water activity over a H2SO4 solution droplet in the stratosphere, which has implications for the parameterization of heterogeneous reaction rates in stratospheric sulfuric acid aerosols. The influence of aerosol composition on the rate of homogeneous ice nucleation from a H2SO4 solution droplet is also discussed. This parameterization can also be used for homogeneous gas phase nucleation calculations of H2SO4 solution droplets under various environmental conditions such as in aircraft exhaust or in volcanic plumes.

Tabazadeh, Azadeh↗
NASA NTRS1999

The Measurement of Sulfur Oxidation Products and Their Role in Homogeneous Nucleation

An improved version of a transverse ion source was developed which uses selected ion chemical ionization mass spectrometry techniques inside of a particle nucleation flow tube. These new techniques are very unique, in that the chemical ionization is done inside of the flow tube rather than by having to remove the compounds and clusters of interest which are lost on first contact,with any surfaces. The transverse source is also unique because it allows the ion reaction time to be varied over more than an order of magnitude, which in turn makes possible the separation of ion induced cluster growth from the charging of preexisting molecular clusters. As a result of combining these unique capabilities, the first ever measurements of prenucleation molecular clusters were performed. These clusters are the intermediate stage of growth in the gas-to-particle conversion process. This new technique provides a means of observing clusters containing 2, 3, 4, ... and up to about 8 sulfuric acid molecules, where the critical cluster size under these measurement conditions was about 4 or 5. Thus, the nucleation process can now be directly observed and even growth beyond the critical cluster size can be investigated. The details of this investigation are discussed in a recently submitted paper, which is included as Appendix A. Measurements of the diffusion coefficient of sulfuric acid and sulfuric acid clustered with a water molecule have also been performed. The measurements are also discussed in more detail in another recently submitted paper which is included as Appendix B. The empirical results discussed in both of these papers provide a critical test of present nucleation theories. They also provide new hope for resolving many of the huge discrepancies between field observation and model prediction of particle nucleation. The second part of the research conducted under this project was directed towards the development of new chemical ionization techniques for measuring sulfur oxidation products.

Eisele, F. L.↗
NASA NTRS1973

Role of pH on the stress corrosion cracking of titanium alloys

Stress corrosion cracking (SCC) experiments were conducted on Ti-8-1-1 wire specimens in hydrochloric and sulfuric acids of variable pH in order to determine the effect of pH on the susceptibility to cracking. The alloy exhibited increasing susceptibility with decreasing pH. By varying the applied potential, it was observed that susceptibility zones exist both in the cathodic and the anodic ranges. In the cathodic range, susceptibility also increased with decreasing applied potential. Corrosion potential-time data in hydrochloric acid (pH 1.7) and sulfuric acid (pH 1.7) indicate that chloride ions lower the corrosion potential of the specimen which, in turn, increases the susceptibility.

Khokhar, M. I.↗
NASA NTRS1976

Hydrogen production by water decomposition using a combined electrolytic-thermochemical cycle

A proposed dual-purpose power plant generating nuclear power to provide energy for driving a water decomposition system is described. The entire system, dubbed Sulfur Cycle Water Decomposition System, works on sulfur compounds (sulfuric acid feedstock, sulfur oxides) in a hybrid electrolytic-thermochemical cycle; performance superior to either all-electrolysis systems or presently known all-thermochemical systems is claimed. The 3345 MW(th) graphite-moderated helium-cooled reactor (VHTR - Very High Temperature Reactor) generates both high-temperature heat and electric power for the process; the gas stream at core exit is heated to 1850 F. Reactor operation is described and reactor innards are illustrated. A cost assessment for on-stream performance in the 1990's is optimistic.

Farbman, G. H.↗
NASA NTRS1983

Venus cloud microphysics

Because sulfuric acid does not wet sulfur, composite drops in the atmosphere of Venus cannot have sulfur 'cores', but must instead have sulfur coats. Both components then communicate with the vapor phase. Drops that are fully coated with sulfur are immune to coalescence; this sets a limit to growth that may explain 'Mode 3' particles. The sulfur coating is probably responsible for the anomalously low refractive indices derived from entry-probe nephelometer data. There appears to be about an order of magnitude less elemental sulfur than sulfuric acid in the clouds.

Young, A. T.↗
NASA NTRS1985

Aerobic sulfur-oxidizing bacteria: Environmental selection and diversification

Sulfur-oxidizing bacteria oxidize reduced inorganic compounds to sulfuric acid. Lithotrophic sulfur oxidizer use the energy obtained from oxidation for microbial growth. Heterotrophic sulfur oxidizers obtain energy from the oxidation of organic compounds. In sulfur-oxidizing mixotrophs energy are derived either from the oxidation of inorganic or organic compounds. Sulfur-oxidizing bacteria are usually located within the sulfide/oxygen interfaces of springs, sediments, soil microenvironments, and the hypolimnion. Colonization of the interface is necessary since sulfide auto-oxidizes and because both oxygen and sulfide are needed for growth. The environmental stresses associated with the colonization of these interfaces resulted in the evolution of morphologically diverse and unique aerobic sulfur oxidizers.

Caldwell, D.↗
NASA NTRS1988

Laboratory studies of sticking coefficients and heterogeneous reactions important in the stratosphere

The discovery of ozone depletion during spring in the Antarctic stratosphere has received wide spread attention. Both meteorological and chemical mechanisms have been used in attempts to explain this observation. The chemical theory focused on the chlorofluoromethanes released into the atmosphere. However, gas-phase, homogeneous reactions alone in the model can not adequately explain such a depletion. Heterogeneous reactions on ice surfaces could be important in the Antarctic stratosphere. These reactions are thought to convert ClONO2 and N2O5 into HNO3 in the solid phase while Cl2, HOCl, and ClNO2 are released into the stratosphere as gas-phase products. The photolysis of Cl2, HOCl, and ClNO2, then produces active chlorine which subsequently removes ozone through several catalytic cycles, including the Cl2O2 mechanism. The polar stratospheric clouds are thought to consist of mixtures of water ice, nitric acid, and sulfuric acid. Condensation of HCl onto the PSC's could provide active surfaces for heterogeneous reactions.

Leu, Ming-Taun↗
NASA NTRS1989

Croconic acid - An absorber in the Venus clouds?

The absorbing species responsible for the UV cloud features and pale yellow hue of the Venus clouds is presently suggested to be the carbon monoxide-polymer croconic acid, which strongly absorbs in the blue and near-UV. Laboratory absorption-coefficient measurements of a dilute solution of croconic acid in sulfuric acid are used as the bases of cloud-scattering models; the Venus planetary albedo's observed behavior in the blue and near-UV are noted to be qualitatively reproduced. Attention is given to a plausible croconic acid-production mechanism for the Venus cloudtop region.

Hartley, Karen K.↗
NASA NTRS1995

Thermal control materials on EOIM-3

Thermal control paints, anodized aluminum, and beta cloth samples were flown on STS-46 as part of the Evaluation of Oxygen Interaction with Materials Experiment (EOIM-3). The thermal control paints flown on EOIM-3 include ceramic and polyurethane-based paints. Passively exposed samples are compared to actively heated samples and controlled exposure samples. Optical property measurements of absorptivity, emissivity, and spectrofluorescence are presented for each paint. Several variations of anodized aluminum, including chromic acid anodize, sulfuric acid anodize, and boric/sulfuric acid anodize were flown on the actively heated trays and the passive exposure trays. The post-flight optical properties are within tolerances for these materials. Also flown were two samples of yellow anodized aluminum. The yellow anodized aluminum samples darkened noticeably. Samples of aluminized and unaluminized beta cloth, a fiberglass woven mat impregnated with TFE Teflon, were flown with passive exposure to the space environment. Data from this part of the experiment is correlated to observations from LDEF and erosion of the Teflon thin film samples also flown on EOIM-3 and LDEF.

Finckenor, Miria M.↗
NASA NTRS2009

Emissions from Biomass Burning in the Yucatan

In March 2006 two instrumented aircraft made the first detailed field measurements of biomass burning (BB) emissions in the Northern Hemisphere tropics as part of the MILAGRO project. The aircraft were the National Center for Atmospheric Research C-130 and a University of Montana/US Forest Service Twin Otter. The initial emissions of up to 49 trace gas or particle species were measured from 20 deforestation and crop residue fires on the Yucatan peninsula. This included two trace gases useful as indicaters of BB (HCN and acetonitrile) and several rarely, or never before, measured species: OH, peroxyacetic acid, propanoic acid, hydrogen peroxide, methane sulfonic acid, and sulfuric acid. Crop residue fires emitted more organic acids and ammonia than deforestation fires, but the emissions from the main fire types were otherwise fairly similar. The Yucatan fires emitted unusually amounts of SO2 and particle chloride, likely due to a strong marine influence on the peninsula.

Yokelson, R.↗
NASA NTRS2013

Friction Modifier Using Adherent Metallic Multilayered or Mixed Element Layer Conversion Coatings

A process for creating conversion coatings and spin, drawing, and extrusion finishes for surfaces, wherein the conversion coatings and spin, drawing, and extrusion finishes contain potassium, phosphorus, nitrogen, and one or more non-alkaline metals and/or one or more metalloids. The process comprises forming an aqueous solution of water, phosphoric acid or sulfuric acid, ammonium hydroxide, an alkali metal hydroxide, and one or more non-alkaline metals and/or one or more metalloids. The aqueous solution forms an anti-friction multilayer conversion and/or mixed element coating or a spin, drawing, and extrusion finish on a surface when applied to the surface, either directly without the use of applied external electromotive force, or as an additive in lubricating fluids.

Schramm, Harry F.↗