Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRESS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Oxide growth stress measurements and relaxation mechanisms for alumina scales grown on FeCrAlY: Oxide growth stress measurements and relaxation mechanisms

Early-stage tensile stress evolution in α-Al 2 O 3 scales during oxidation of FeCrAlY at 1000, 1050, 1100, and 1200 °C was monitored in situ by use of synchrotron radiation. Tensile stress development as a function of oxidation temperature indicated a dynamic interplay between stress generation and relaxation. An analysis of the time dependence of the data indicated that the observed relaxation of the initial tensile stress in the oxide scales at 1100 and 1200°C is dominated by creep in the α-Al 2 O 3 . A thin layer of a (Fe,Cr,Al) oxide was observed at the oxide-gas interface, consistent with a mechanism whereby the conversion of (Fe,Cr,Al) 2 O 3 to α-Al 2 O 3 produces an initial tensile stress in the alumina scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Incorporation of salinity, nitrogen, and shading stress factors into the Huesemann Algae Biomass Growth model

The Huesemann Algae Biomass Growth (HABG) model predicts microalgae biomass growth in outdoor raceways as a function of water temperature and incident light intensity. The model over-predicted growth in several Regional Algal Feedstock Testbed (RAFT) experiments. Inspection of the culture conditions suggested that salinity stress, nutrient limitation, and shading reduced growth, which were not included in the original model. Laboratory experiments were carried out to measure growth response of S. obliquus to high salinity and limited nitrogen. In addition, the shading effect was estimated based on raceway geometry, solar angle, albedo and measured light intensity data. In this study, the improvement of model performance is presented step by step as each growth limiting factor is incorporated into the model. The new salinity, shanding, and nutrient stress factors remove most of the over-prediction of the original model. Comparison of the model with observed data indicated that ignoring the lag phase also resulted in overprediction. Delaying the start of the simulation until the end of the lag phase and inclusion of stress factors lowered model inaccuracy from 90% over-prediction to within ±10% in six out of seven batches.

09 BIOMASS FUELS↗

Mini-Review: Oxidative stress, redox stress or redox success?

Highlights: • Reactive oxygen species were major drivers of evolution. • Reductive stress may not be a very useful concept. • Major antioxidant defences include restriction of O{sub 2} levels and sequestration of iron ions into non-redox active forms. • These defences allowed aerobic life to evolve but led to a battle between host and pathogens for iron. The first life forms evolved in a highly reducing environment. This reduced state is still carried by cells today, which makes the concept of “reductive stress” somewhat redundant. When oxygen became abundant on the Earth, due to the evolution of photosynthesis, life forms had to adapt or become extinct. Living organisms did adapt, proliferated and an explosion of new life forms resulted, using reactive oxygen species (ROS) to drive their evolution. Adaptation to oxygen and its reduction intermediates necessitated the simultaneous evolution of select antioxidant defences, carefully regulated to allow ROS to perform their major roles. Clearly this “oxidative stress” did not cause a major problem to the evolution of complex life forms. Why not? Iron and oxygen share a close relationship in aerobic evolution. Iron is used in proteins to transport oxygen, promote electron transfers, and catalyse chemical reactions. In all of these functions, iron is carefully sequestered within proteins and restricted from reacting with ROS, this sequestration being one of our major antioxidant defences. Iron was abundant to life forms before the appearance of oxygen. However, oxygen caused its oxidative precipitation from solution and thereby decreased its bioavailability and thus the risk of iron-dependent oxidative damage. Micro-organisms had to adapt and develop strategies involving siderophores to acquire iron from the environment and eventually their host. This battle for iron between bacteria and animal hosts continues today, and is a much greater daily threat to our survival than “oxidative stress” and “redox stress”.

60 APPLIED LIFE SCIENCES↗

Stress relaxation in pre-stressed aluminum core–shell particles: X-ray diffraction study, modeling, and improved reactivity

Stress relaxation in aluminum micron-scale particles covered by alumina shell after pre-stressing by thermal treatment and storage was measured using X-ray diffraction with synchrotron radiation. Pre-stressing was produced by annealing Al particles at 573K followed by fast cooling. While averaged dilatational strain in Al core was negligible for untreated particles, it was measured at 4.40×10 -5 and 2.85×10 -5 after 2 and 48 days of storage. Consistently, such a treatment leads to increase in flame propagation speed for Al+CuO mixture by 37% and 25%, respectively. Analytical model for creep in alumna shell and stress relaxation in Al core-alumina shell structure is developed and activation energy and pre-exponential multiplier are estimated. The effect of storage temperature and annealing temperature on the kinetics of stress relaxation was evaluated theoretically. These results provide estimates for optimizing Al reactivity with the holding time at annealing temperature and allowable time for storage of Al particles for various environmental temperatures.

42 ENGINEERING↗

Estimation of stress and stress-induced permeability change in a geological nuclear waste repository in a thermo-hydrologically coupled simulation

Geologic disposal is a promising solution for a safe permanent isolation of accumulated high-level nuclear waste from nuclear powerplants. The behavior of host rock is highly coupled thermally, hydromechanically, and chemically. Numerical simulations of such coupled phenomena for the extremely long term (>100,000 years) and large length scale (>1 km) of geologic disposal remain to be computationally challenging. In this study, a methodology has been developed to approximate stress and stress-induced permeability change in host rock using only thermo-hydrological (TH) variables. A coupled thermo-hydromechanical (THM) simulation is carried out using TOUGH-FLAC simulator to model THM behaviors of a generic nuclear waste repository, in order to evaluate the performance of the developed methodology, which is implemented in a coupled TH simulation. Results show that stress and permeability change estimated by the developed methodology in the TH-coupled simulation match those calculated in the THM-coupled simulation over the simulated timeframe of over 10,000 years. Details about errors in stress and permeability estimates accrued by the developed methodology are discussed here. The developed methodology will help incorporate stress-induced permeability change into existing TH simulators for the long-term radionuclide transport in geologic disposal.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Effect of stress evolution on microstructural behavior in U-Mo/Al dispersion fuel [Effect of stress on microstructural evolution in U-Mo/Al dispersion fuel]

U-Mo/Al dispersion fuel irradiated to high burnup at high power (high fission rate) exhibited microstructural changes such as deformation of the fuel particles, pore growth, and rupture of the Al matrix. The driving force for these microstructural changes was meat swelling caused by a combination of fuel particle swelling and interaction layer growth. Five miniplates with well-recorded fabrication data and irradiation conditions were selected, and their PIE data was analyzed. ABAQUS finite element analysis (FEA) was utilized to simulate the microstructural evolution of the plates. Using the simulation results shear stress, effective stress and hydrostatic stress exerted on both the fuel particles and the Al matrix were determined. The effects of fabrication and irradiation variables on stress-induced microstructural evolutions, such as pore growth in the interaction layers and Al matrix rupture, were investigated. The observed microstructural changes were consistent with the calculated stress distribution in the meat.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Highly Contrasting Static Charging and Bias Stress Effects in Pentacene Transistors with Polystyrene Heterostructures Incorporating Oxidizable N , N '-Bis(4-methoxyphenyl)aniline Side Chains as Gate Dielectrics

Charge storage and trapping properties of polymer dielectrics govern the charge densities of adjacent semiconductors and greatly influence the on-off switching voltage (threshold voltage, V th ) of organic field-effect transistors (OFETs) when the polymers are used as gate insulators. Intentional charging of polymer dielectrics in OFETs can change V th and affect the bias stress. We describe a chemical design and fabrication protocol to construct multilayer-stack dielectrics for pentacene-based OFETs using different polystyrene (PS)-based polymers in each layer, with oxidizable N,N-bis(4-methoxyphenyl)anilino (TPAOMe)-substituted styrene copolymers in arbitrary vertical positions in the stacks. Thermal, byproduct-free crosslinking of benzocyclobutene subunits provides integrity to the multilayer structure by preventing dissolution of the previous deposited layer. Neutron reflectivity data verified the multilayer morphology. We compared the Vth shift before and after charging the stacks by application of ±100V across 0.5-1 µm total film thicknesses. Bias stress was the dominant effect in bilayer devices with a TPAOMe layer in contact with the pentacene, indicated by the direction of V th shift associated with either polarity of external electric field. In structures with no TPAOMe subunit in contact with the pentacene, when charging with -100V on top of the source and drain electrodes, electron injection from pentacene to dielectric was the major charging mechanism, again consistent with the bias stress direction. When charging with +100V, bilayer devices without TPAOMe showed little change in V th , suggesting there was no bias stress effect or charge injection in these devices for this charging polarity. For the bilayer devices with the TPAOMe layer in the bottom, and the trilayer devices with TPOMe in the middle, when +100V was applied, the V th shifts were opposite those expected from bias stress. Dipole formation or partial ionization of chargeable groups at the interface between the dielectric layers are likely polarization mechanisms in these cases. A simple analytical model supports the plausibility of these mechanisms. This work provides examples of both stabilization and shifting of V th , and therefore controlling charge carrier density, in semiconductors overlying the dielectric multilayers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Astragaloside IV improved antioxidative stress capacity and related gene expression of the Keap1‐Nrf2 pathway in grass carp ( Ctenopharyngodon idella ) hepatocytes under heat stress

Abstract This study aims to investigate the protective effects of astragaloside IV (AS‐IV) on the hepatocytes of grass carp ( Ctenopharyngodon idella ) on heat stress. Cultured cells were treated with AS‐IV (0, 50, 100 and 200 μg/ml) at 28°C for 24 h and then exposed to heat stress by increasing the culturing temperature (32 ± 0.5°C) for 6 h. The increased temperatures significantly reduced cell viability and superoxide dismutase (SOD) activity, and increased malondialdehyde (MDA) levels in the 0 μg/ml AS‐IV treatment group at 32°C, but the grass carp hepatocytes treated with 100 and 200 μg/ml AS‐IV had significantly increased cell viability and SOD activity and decreased MDA levels. The mRNA levels of keap1a , keap1b , nrf2 , gsh‐px , cat , cu‐zn sod , mgst1 and il‐6 were significantly lower in the 0 μg/ml AS‐IV treatment group at 32°C, while those of keap1a , nrf2 , gsh‐px , cat , cu‐zn sod , gstp1 , ho‐1 and il‐6 were significantly higher in cells treated with 100 or 200 μg/ml AS‐IV. Our findings indicate that AS‐IV could enhance the antioxidative stress capacity of grass carp hepatocytes under heat stress, and its mechanism may be associated with the activation of the Keap1‐Nrf2 pathway. Thus, these results provide new insights into how to alleviate heat stress in grass carp.

Liu, Hua↗

Residual Stress Modeling and Advanced Diffraction Measurements of 347H Steel Weldments

The 347H stainless steel is a primary high-temperature material for many energy and power generation industries. Stress relief cracking (SRC) has been a particular concern in welding of this material. The residual stress induced by welding and its evolution during post-welding heat treatment (PWHT) and subsequent operating and service conditions is one of the primary factors contributing to SRC. The lifetime of welded structure components is also controlled by the precipitation kinetics that accompanies PWHT, stress relaxation process, and long-term aging and complex synergistic factors. Various theories have been proposed in the past to explain SRC. However, a widely accepted approach to predicting the entire damage evolution and the resulting performance reduction is still lacking. This study is to demonstrate a reliable solution for two critical issues that affect the predictions. First, the residual stress distribution obtained from both simulation and neutron diffraction is compared, which increases the accuracy of mechanical analysis simulation model and therefore builds a solid basis for the lifetime prediction model. Second, the generation, evolution, and annihilation of precipitates are monitored by the synchrotron diffraction experiment. Preliminary results demonstrate the critical importance of precipitation kinetics on the residual stress distribution/redistribution during heat treatments.

Yang, Yi↗

Determination of Stress-Free Lattice Spacing (D₀) for Residual Stress Relaxation Measurement in Ni-based Superalloys by Neutron Diffraction

The residual stress and its relaxation in critical engineering components are key to structural materials reliability. The determination of residual stress in bulk engineering structures like Ni-based superalloys can be conducted by measuring the lattice strain with penetrating neutron diffraction. The state-of-the-art engineering diffraction beamline VULCAN at the Oak Ridge National Laboratory (ORNL) Spallation Neutron Source (SNS) provides the critical capability to evaluate the residual strain/stress relaxation in engineering component thanks to the high flux and event data features. By the means of residual stress/strain calculation, it is critical to accurately determine the stress-free lattice spacing d₀, which can be altered by the change of chemistry, unrelieved stress, and measurement scheme. Here we reported d₀ determination for determining residual stress relaxation and distribution in Alloy 718 superalloys after different quenching treatments. Selection of locations for d₀ measurement was discussed by considering the neutron path, attenuation and sample alignment. A dynamic d₀ that resulted from atom diffusion and chemistry change was estimated as function of time for the in-situ relaxation characterization. It demonstrated how the dynamic d₀ values may influence on the strain calculation in different thermally treated samples. The results highlight the importance of dynamic d₀ for in-situ relaxation involving chemical changes and provide guidance to the dynamic d₀ measurement and simulation.

36 MATERIALS SCIENCE↗

Rheology of dense fiber suspensions: Origin of yield stress, shear thinning, and normal stress differences

We use high-fidelity computational model of fiber suspension to investigate suspension rheology. We investigate the interplay between the hydrodynamic, noncontact attractive and repulsive, and interfiber contact interactions. The shear-thinning viscosity and finite yield stress obtained from the Immerse Boundary Method simulations align quantitatively with experimental findings from the literature. The study demonstrates that attractive interactions lead to both yield stress and shear thinning behavior in rigid fiber suspensions. This discovery holds significance as it contributes to the ongoing debate on the source of yield stress in fiber suspensions. The proposed model is used to quantify normal stresses in addition to shear thinning and yield stress.

Ardekani, Arezoo↗

Tensile behavior and flow stress anisotropy of accumulative roll bonded Cu-Nb nanolaminates

The flow stress, ductility, and in-plane anisotropy are evaluated for bulk accumulative roll bonded copper-niobium nanolaminates with layer thicknesses ranging from 1.8 μm to 15 nm. Uniaxial tensile tests conducted parallel to the rolling direction and transverse direction demonstrate that ductility generally decreases with decreasing layer thickness; however, at 30 nm, both high strengths (1200 MPa) and significant ductility (8%) are achieved. The yield strength increases monotonically with decreasing layer thickness, consistent with the Hall-Petch relationship, and significant in-plane flow stress anisotropy is observed. Taylor polycrystal modeling is used to demonstrate that crystallographic texture is responsible for the in-plane anisotropy and that the effects of texture dominate even at nanoscale layer thicknesses.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Intrinsic Rotation from a Residual Stress at the Boundary of a Cylindrical Laboratory Plasma

An azimuthally symmetric radially sheared azimuthal flow is driven by a nondiffusive, or residual, turbulent stress localized to a narrow annular region at the boundary of a cylindrical magnetized helicon plasma device. A no-slip condition, imposed by ion-neutral flow damping outside the annular region, combined with a diffusive stress arising from turbulent and collisional viscous damping in the central plasma region, leads to net plasma rotation in the absence of momentum input.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A Generalized Stress Inversion Approach With Application to Residual Stress Estimation

In this work develop a generalized stress inversion technique (or the generalized inversion method) capable of recovering stresses in linear elastic bodies subjected to arbitrary cuts. Specifically, given a set of displacement measurements found experimentally from digital image correlation (DIC), we formulate a stress estimation inverse problem as a partial differential equation-constrained optimization problem. We use gradient-based optimization methods, and we accordingly derive the necessary gradient and Hessian information in a matrix-free form to allow for parallel, large-scale operations. By using a combination of finite elements, DIC, and a matrix-free optimization framework, the generalized inversion method can be used on any arbitrary geometry, provided that the DIC camera can view a sufficient part of the surface. We present numerical simulations and experiments, and we demonstrate that the generalized inversion method can be applied to estimate residual stress.

42 ENGINEERING↗

Origin of stress gradients induced in capped, copper metallization

Stress gradients generated near the top surface of Cu thin films by capping layers, as measured using a combination of conventional and glancing incidence x-ray diffraction, exhibit heterogeneous behavior that is directly related to plastic anisotropy within the Cu grains. A comparison of stress gradients measured from several x-ray reflections to their corresponding Schmid factors yields a consistent, critical resolved shear stress. The results experimentally verify that dislocation-mediated plasticity is responsible for the creation of stress gradients at the Cu film/cap interface. Depth-dependent measurements reveal that the observed gradients are localized to within 200 nm of this interface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗