Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOLAR CELL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Study of the Staebler-Wronski degradation effect in a-Si:H based p-i-n solar cell

Conversion of solar energy into electricity using environmentally safe and clean photovoltaic methods to supplement the ever increasing energy needs has been a cherished goal of many scientists and engineers around the world. Photovoltaic solar cells on the other hand, have been the power source for satellites ever since their introduction in the early sixties. For widespread terrestrial applications, however, the cost of photovoltaic systems must be reduced considerably. Much progress has been made in the recent past towards developing economically viable terrestrial systems, and the future looks highly promising. Thin film solar cells offer cost reductions mainly from their low processing cost, low material cost, and choice of low cost substrates. These are also very attractive for space applications because of their high power densities (power produced per kilogram of solar cell pay load) and high radiation resistance. Amorphous silicon based solar cells are amongst the top candidates for economically viable terrestrial and space based power generation. Despite very low federal funding during the eighties, amorphous silicon solar cell efficiencies have continually been improved - from a low 3 percent to over 13 percent now. Further improvements have been made by the use of multi-junction tandem solar cells. Efficiencies close to 15 percent have been achieved in several labs. In order to be competitive with fossil fuel generated electricity, it is believed that module efficiency of 15 percent or cell efficiency of 20 percent is required. Thus, further improvements in cell performance is imperative. One major problem that was discovered almost 15 years ago in amorphous silicon devices is the well known Staebler-Wronski Effect. Efficiency of amorphous silicon solar cells was found to degrade upon exposure to sunlight. Until now their is no consensus among the scientists on the mechanism for this degradation. Efficiency may degrade anywhere from 10 percent to almost 50 percent within the first few months of operation. In order to improve solar cell efficiencies, it is clear that the cause or causes of such degradation must be found and the processing conditions altered to minimize the loss in efficiency. This project was initiated in 1987 to investigate a possible link between metallic impurities, in particular, Ag, and this degradation. Such a link was established by one of the NASA scientists for the light induced degradation of n+/p crystalline silicon solar cells.

Naseem, H. A.↗
NASA NTRS1982

Heat transparent high intensity high efficiency solar cell

An improved solar cell design is described. A surface of each solar cell has a plurality of grooves. Each groove has a vertical face and a slanted face that is covered by a reflecting metal. Light rays are reflected from the slanted face through the vertical face where they traverse a photovoltaic junction. As the light rays travel to the slanted face of an adjacent groove, they again traverse the junction. The underside of the reflecting coating directs the light rays toward the opposite surface of solar cell as they traverse the junction again. When the light rays travel through the solar cell and reach the saw toothed grooves on the under side, the process of reflection and repeatedly traversing the junction again takes place. The light rays ultimately emerge from the solar cell. These solar cells are particularly useful at very high levels of insolation because the infrared or heat radiation passes through the cells without being appreciably absorbed to heat the cell.

Evans, J. C., Jr.↗
DOE OSTI2022

Understanding Mass Transport in Copper Electrolyte-Based Dye-Sensitized Solar Cells

Copper redox shuttles, particularly [Cu(tmby) 2 ] 2+/1+ (tmby = bis(4,4',6,6'-tetramethyl-2,2'-bipyridine)), proved to be among the best electrolytes for dye-sensitized solar cells (DSCs), realizing higher power conversion efficiencies both under full sun and indoor illumination than conventional iodide/triiodide and cobalt electrolytes. Even though [Cu(tmby) 2 ] 2+/1+ renders a relatively higher performance, this metal complex is bulky and is limited by mass transport. Since the regeneration of the dye ground state by Cu I and the reaction of Cu II at the counter electrode are comparatively faster processes, the efficiency of DSC involving Cu I /Cu II electrolytes under relatively high light intensities is largely governed by the diffusion of Cu I /Cu II species. Understanding mass transport in these solar cells will enable further improvements in the performance of such copper-based DSCs. Here in the present study, the role of illumination intensity on the photogenerated current and its relationship to mass transport is evaluated using the best cosensitized dye (D35:XY1) and copper electrolyte ([Cu(tmby) 2 ] 2+/1+ ) combination.

14 SOLAR ENERGY↗
DOE OSTI2022

Reduced Recombination and Improved Performance of CdSe/CdTe Solar Cells due to Cu Migration Induced by Light Soaking

The performance of CdTe solar cells has advanced impressively in recent years with the incorporation of Se. Instabilities associated with light soaking and copper reorganization have been extensively examined for the previous generation of CdS/CdTe solar cells, but instabilities in Cu-doped Se-alloyed CdTe devices remain relatively unexplored. In this work, we fabricated a range of CdSe/CdTe solar cells by sputtering CdSe layers with thicknesses of 100, 120, 150, 180, and 200 nm on transparent oxide-coated glass and then depositing CdTe by close-spaced sublimation. After CdCl 2 annealing, Cu-doping, and back metal deposition, a variety of analyses were performed both before and after light soaking to understand the changes in device performance. The device efficiency was degraded with light soaking in most cases, but devices fabricated with a CdSe layer thickness of 120 nm showed reasonably good efficiency initially (13.5%) and a dramatic improvement with light soaking (16.5%). Here, the efficiency improvement is examined within the context of Cu ion reorganization that is well known for CdS/CdTe devices. Low-temperature photoluminescence data and V oc versus temperature measurements indicate a reduction in nonradiative recombination due to the passivation of defects and defect complexes in the graded CdSe x Te 1–x layer.

CdSexTe1−x↗
DOE OSTI2020

Isolating p- and n-Doped Fingers With Intrinsic Poly-Si in Passivated Interdigitated Back Contact Silicon Solar Cells

Polycrystalline silicon on silicon oxide (poly-Si/SiO x ) passivating contacts enable ultra high efficiency interdigitated back contact silicon solar cells. To prevent shunt between n- and p-type doped fingers, an insulating region is required between them. We evaluate the use of intrinsic poly Si for this isolation region. Interdigitated fingers were formed by plasma deposition of doped hydrogenated amorphous silicon through mechanically aligned shadow masks, on top of a full-area intrinsic amorphous silicon layer. High temperature annealing then crystallized the a-Si:H to poly Si and drove in the dopants. Two mechanisms were identified which cause contamination of the intrinsic poly Si gap during processing. During deposition of doped fingers, we show using secondary ion mass spectrometry and conductivity measurements that the intrinsic gap becomes contaminated by doped a-Si:H tails several nanometers thick to concentrations of ~10 20 cm -3 . Another source of contamination occurs during high-temperature annealing, where dopants desorb from doped regions and readsorb onto intrinsic a Si:H. Both pathways reduce the resistivity of the intrinsic gap from ~10 5 Ω·cm to ~10 -1 Ω·cm. We show that plasma etching of the a-Si:H surface before crystallizing with a capping layer can eliminate the contamination of the intrinsic poly-Si, maintaining a resistivity of ~10 5 Ω·cm. Lastly, this demonstrates masked plasma deposition as a dopant patterning method for Si solar cells.

14 SOLAR ENERGY↗
NASA NTRS1978

Evaluation of solar cells and arrays for potential solar power satellite applications

Proposed solar array designs and manufacturing methods are evaluated to identify options which show the greatest promise of leading up to the develpment of a cost-effective SPS solar cell array design. The key program elements which have to be accomplished as part of an SPS solar cell array development program are defined. The issues focussed on are: (1) definition of one or more designs of a candidate SPS solar array module, using results from current system studies; (2) development of the necessary manufacturing requirements for the candidate SPS solar cell arrays and an assessment of the market size, timing, and industry infrastructure needed to produce the arrays for the SPS program; (3) evaluation of current DOE, NASA and DOD photovoltaic programs to determine the impacts of recent advances in solar cell materials, array designs and manufacturing technology on the candidate SPS solar cell arrays; and (4) definition of key program elements for the development of the most promising solar cell arrays for the SPS program.

Almgren, D. W.↗
DOE OSTI2024

Interfacial engineering for high performance carbon-based perovskite solar cells

Perovskite solar cells fabricated with carbon-based counter electrodes demonstrate decreased cost, enhanced simplicity and speed of production, and increased stability compared to those produced with standard metallic electrodes. This significant improvement of device stability, cost reduction, and production scalability indicates a promising direction for commercial development and availability of perovskite solar technology. The main limitation of carbon-based perovskite devices is the flawed contact between the carbon electrode and perovskite film which decreases device quality and performance, thereby necessitating treatment of the carbon/perovskite interface. This review provides an overview of the current state of carbon-based perovskite devices, discusses progress in carbon/perovskite interface modification methods, and suggests future directions for the research of carbon electrode/perovskite film interface manipulation.

14 SOLAR ENERGY↗
DOE OSTI2022

π-Extension and chlorination of non-fullerene acceptors enable more readily processable and sustainable high-performance organic solar cells

Organic solar cells (OSCs) processed without halogenated solvents and complex treatments are essential for future commercialization. Herein, we report three novel small molecule acceptors (NFAs) consisting of a Y6-like core but with π-extended naphthalene with progressively more chlorinated end-capping groups and a longer branched chain on the Nitrogen atom. These NFAs exhibit good solubilities in non-chlorinated organic solvents, broad optical absorptions, close π-π stacking distances (3.63–3.84 Å), and high electron mobilities (~10 -3 cm 2 V -1 s -1 ). Further, the o-xylene processed and as-cast binary devices using PM6 as the donor polymer exhibit a PCE increasing upon progressive chlorination of the naphthalene end-capping group from 8.93% for YN to 14.38% for YN-Cl to 15.00% for YN-2Cl. Furthermore similarly processed ternary OSCs were fabricated by employing YN-Cl and YN-2Cl as the third component of PM6:CH1007 blends (PCE = 15.75%). Compared to all binary devices, the ternary PM6:CH1007:YN-Cl (1:1:0.2) and PM6:CH1007:YN-2Cl (1:1:0.2) cells exhibit significantly improved PCEs of 16.49% and 15.88%, respectively, which are among the highest values reported to date for non-halogenated solvent processed OSCs without using any additives and blend post-deposition treatments.

14 SOLAR ENERGY↗
DOE OSTI2021

On-device lead absorbing tapes for sustainable perovskite solar cells

Perovskite solar cells are a promising technology that could facilitate and accelerate the energy transition to a sustainable future. However, the toxicity of Pb remains one of the obstacles impeding their commercialization. Here we apply on-device tapes to absorb leaked lead from damaged devices. Furthermore, our chemical approach can capture over 99.9% of leakage without compromising the performance and operation.

14 SOLAR ENERGY↗
DOE OSTI2023

Tuning the Intermolecular Electrostatic Interaction toward High-Efficiency and Low-Cost Organic Solar Cells

Organic solar cells (OSCs) have achieved much progress with rapidly increasing power conversion efficiencies (PCEs). It should be noted that the top-performance OSCs are generally consisted of active materials with complex chemical structures, resulting in high costs. Here, combining the material design and morphology control, high-efficiency OSCs are fabricated by a low-cost donor: acceptor blend. A completely non-fused electron acceptor named Tz is designed and synthesized via introducing thiazole units on both sides of a bithiophene core, which shows an outstanding PCE of 13.3% with a typical polythiophene donor. More importantly, optimization guidelines are presented to get excellent morphology for low-cost donor:acceptor systems. Three polythiophenes are selected, poly(3-hexylthiophene) and its two derivatives with electron-withdrawing substitutions (PDCBT and PDCBT-2F), as donors to fabricate the cell devices. The computational and experimental data reveal that decreasing the electrostatic interaction between polythiophene and Tz is the key to getting a suppressed miscibility and thus a high phase purity. Finally, this study provides insight into the molecular design and donor:acceptor matching requirements for high-efficiency and low-cost OSCs.

14 SOLAR ENERGY↗