Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SLAGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Rheological Transitions of the Solid-Bearing Slag During Cooling Process

The viscosity of basic oxygen furnace slag modified by the addition of Al{sub 2}O{sub 3}, SiO{sub 2}, and Na{sub 2}O was measured via a rotational-type rheometer. The experiment was performed under both continuous cooling condition (5 °C/min) at a constant rotational speed (30 rpm) and isothermal condition at various rotational speeds (between 2 and 120 rpm). The present work suggests that during cooling from liquid to solid, the slag successively undergoes Newtonian regime, shear thinning (time depedent) and thixotropy with a time-dependent apparent yield stress. The corresponding slag microstructure is (1) a fully liquid or partially liquid slag with negligible crystal–crystal interaction in the Newtonian regime, (2) a liquid slag with crystal aggregates/clusters in the shear thinning regime and (3) a skeletal solid network in the regime of thixotropy with a certain level of apparent yield stress.

36 MATERIALS SCIENCE↗

Effect of Direct Reduced Iron (DRI) on Dephosphorization of Molten Steel by Electric Arc Furnace Slag

We investigated the effect of direct reduced iron (DRI) addition on dephosphorization of molten steel by electric arc furnace (EAF) slag at 1823 K (1550 °C). Various phenomena such as CO gas evolution and slagmaking by gangue oxides in DRI were experimentally observed at each reaction step. Thermodynamic behaviors of phosphorus, oxygen, and carbon were strongly dependent on DRI content. Basicity, which is the thermodynamic driving force of dephosphorization, decreased with the increasing DRI content because SiO{sub 2} concentration in the slag was proportional to DRI addition. The excess free energy of P{sub 2}O{sub 5} increased with the increasing SiO{sub 2} content in slag. A higher DRI content made dephosphorization difficult by decreasing the basicity and stability of P{sub 2}O{sub 5} in the slag. Therefore, when using DRI in EAF process, it is very important to control the basicity of slag.

36 MATERIALS SCIENCE↗

Kinetic Modeling of the Silicothermic Reduction of Manganese Oxide from Slag

A model was developed to describe the mixed rate control kinetics in systems with MnO-SiO{sub 2}-CaO-Al{sub 2}O{sub 3} slags and Fe-Si metal droplets. During the reaction of Fe-Si droplets and slag, Mn{sup 2+} transport was found to be part of controlling the system but could not sufficiently describe all initial conditions (chiefly, changes to initial silicon content). The current model describes the kinetics of the stated system and offers answers to the question of rate control; the model has been fitted to nine datasets of varying initial conditions including initial [Si], initial (MnO), initial droplet size, and reaction temperature. The fitted mass transfer coefficients for metal and slag were 2.3 × 10{sup −4} and 6.7 × 10{sup −4} m/s, respectively; these values are constant across the nine datasets. Previous claims about the efficiency of silicon usage in reducing manganese have been modified; it appears that the formation of silica is favored throughout the reaction, but that the formation of a silicon monoxide gas layer on the metal surface dramatically impacts the rate of reaction. As a measure of overall fit of the model, the average of the root-mean-square errors for all datasets is 14 pct. Mass transport in slag is twice as influential on rate control as the metal phase. The simultaneous transport of both Mn{sup 2+} and silicate dimers controls mass transport in the slag. Both [Si] and [Mn] can control from the metal side but are dependent on the initial conditions.

36 MATERIALS SCIENCE↗

Physicochemical Properties of the Molten Iron-Rich Slags Related to the Copper Recovery

The properties of a molten slag play an important role in the separation of the slag from the matte during copper smelting. In this study, the viscosity, electrical conductivity, density, and surface tension of molten FeO{sub t}-SiO{sub 2}-CaO-based slags were measured, and the effects of the common constituents, such as CaO, Fe{sub 3}O{sub 4}, and Cu{sub 2}O, on various properties were investigated. The primary phases in the molten slags which are suitable for the copper recovery process were obtained, and they mainly correspond to fayalite and tridymite. The comparison of the static settling properties of molten industrial copper slag before and after modification is also discussed.

36 MATERIALS SCIENCE↗

Improving the Modeling of Slag and Steel Bath Chemistry in an Electric Arc Furnace Process Model

An improvement to the thermochemical module of the electric arc furnace (EAF) process model developed by Meier based on the work of Logar, Dovžan, and Škrjanc is presented. Different models for the calculation of activities in melt and slag are implemented, and separate reaction zones are defined for the interaction of slag and melt, the injection of oxygen, and the injection of carbon. For each zone, equilibrium compositions and reaction rates are calculated. Furthermore, diffusion of species is considered as a rate-limiting factor in reactions between slag and melt, and diffusion rates are calculated from the bulk melt to the reaction zone where reactions with the slag take place. Oxygen and sulfur dissolved in the melt and CaS in the slag are added as new species not previously considered in the EAF model. The treatment of carbon is revised to reduce model complexity and improve accuracy. The improved model is validated using extensive data from an industrial EAF, and results are compared to measured data as well as results obtained with the unmodified model. The different models for the determination of thermodynamic activities and their impacts on the duration of the simulation as well as its results are evaluated.

36 MATERIALS SCIENCE↗

Insight into the Relationship Between Viscosity and Structure of CaO-SiO{sub 2}-MgO-Al{sub 2}O{sub 3} Molten Slags

This article elucidates the quantitative relationship between viscosity and structure in a basic slag system of CaO-SiO{sub 2}-MgO-Al{sub 2}O{sub 3} and focuses on the role of Al{sub 2}O{sub 3}. Slag viscosity was measured by the rotating cylinder method, and structural information was obtained using Fourier transformation infrared, Raman and magic angular spinning nuclear magnetic resonance (MAS-NMR) techniques. The results show that, as the Al{sub 2}O{sub 3} content increased, slag viscosity increased initially and decreased afterwards, directly indicating that Al{sub 2}O{sub 3} had an amphoteric effect on slag viscosity. The Raman spectra verified that with increasing Al{sub 2}O{sub 3} content, the concentrations of Q{sup 0}(Si) and Q{sup 2}(Si) decreased first and then increased, while that of Q{sup 1}(Si) kept increasing and that of Q{sup 3}(Si) increased first and then decreased. The {sup 27}Al MAS-NMR spectra proved that the mole ratios of AlO{sub 5} and AlO{sub 6} to AlO{sub 4} kept increasing with the increase of Al{sub 2}O{sub 3} content, and, overall, Al{sub 2}O{sub 3} changed from a network former to a network modifier. The relationship between the viscosity and structure of the molten slags was further analyzed quantitatively based on the modified (NBO/T), denoted as (NBO/T)′, and we found a fine linear correlation between the logarithm of viscosity and (NBO/T)′. Moreover, the variations of thermodynamic properties of this system also indirectly supported the present experimental results.

36 MATERIALS SCIENCE↗

Distinctive microstructural features of aged sodium silicate-activated slag concretes

Electron microscopic characterisation of 7-year old alkali-activated blast-furnace slag concretes enabled the identification of distinct microstructural features, providing insight into the mechanisms by which these materials evolve over time. Backscattered electron images show the formation of Liesegang-type ring formations, suggesting that the reaction at advanced age is likely to follow an Oswald supersaturation–nucleation–depletion cycle. Segregation of Ca-rich veins, related to the formation of Ca(OH){sub 2}, is observed in microcracked regions due to the ongoing reaction between the pore solution and available calcium from remnant slag grains. A highly dense and uniform interfacial transition zone is identified between siliceous aggregate particles and the alkali activated slag binders, across the concretes assessed. Alkali-activated slag concretes retain a highly dense and stable microstructure at advanced ages, where any microcracks induced at early ages seem to be partially closing, and the remnant slag grains continue reacting.

36 MATERIALS SCIENCE↗

Carbon sequestration of steel slag and carbonation for activating RO phase

Carbonation of Ca/Mg minerals in industrial alkaline residues is a technology to sequester CO{sub 2} and reduce its emissions to the atmosphere. In this work, BSE-EDS were used to determine the mineral phase in steel slag; compositions of RO phase were identified and simulated. The carbon sequestration of steel slag was studied, and RO phase was activated by carbonation. Result shows that the amount of CO{sub 2} sequestered in steel slag and RO phase increases as carbonation time increases. Under autoclaving condition, the hydration ratio of MgO in RO phase was 20.10%. Through carbonation, up to 58.83% of MgO in RO phase can be converted into MgCO{sub 3}, and the activation of RO phase by carbonation was manifested. The mechanical properties and volume stability of carbonated steel slag were improved, proving that the positive effect of carbonation on steel slag when applied in cement and cementitious materials.

36 MATERIALS SCIENCE↗

Factors affecting the reactivity of slag at early and late ages

This study investigates the difference between the reactivity of slag in NaOH solution (w/s = 100) and in cement paste (w/b = 0.4). The reactivity of slag is much higher in NaOH solution than in cement paste. When the NaOH solution is saturated with portlandite, the rate of reaction of slag decreases to approach that in cement paste. This suggests that the slower reaction of slag in cement paste might be due to the presence of calcium ions released by the clinker phases. At 28 days, relative humidity measurements indicate that water is only present in pores less than 6 nm. Above 6 nm, hydration cannot take place due to the lack of water. From a thermodynamic point of view, the small size of water filled pores may slow down the slag reaction due to the high concentration of species in solution required for hydrate growth to balance the increase of the surface energy.

36 MATERIALS SCIENCE↗

Analysis of slags using laser-induced breakdown spectroscopy

The feasibility of laser-induced breakdown spectroscopy (LIBS) for the analysis of gasification slags was investigated by comparing LIBS results to the results of an ICP-OES analyzer. A small amount of slag sample was placed on a piece of double sided adhesive tape attached to a glass microscope slide and analyzed for Al, Ca, Fe, Si, and V which are major elements found in slags. The partial least squares regression (PLS-R) and univariate simple linear regression (SLR) calibration methods indicated that apart from V (accuracy up to + 20%) the accuracy of analysis varies within 0.35–6.5% for SLR and 0.06–10% for PLS-R. A paired-sample t-test within the 95% confidence level yielded p-values greater than 0.05, meaning no appreciable statistical difference was observed between the univariate SLR with internal standardization and the multivariate PLS-R for most of the analytes. From the results obtained in this work, LIBS response varies depending on the element and the technique used for quantitative analysis. Simultaneous use of the univariate calibration curves with internal standard (intensity ratio) and PLS regression in multi-elemental analysis can help reduce the matrix effect of slags associated to their high variation in concentration. Overall, these results demonstrate the capability of LIBS as an alternative technique for analyzing gasification slags. Estimated limits of detection for Al, Ca, Fe, Si and V were 0.167, 0.78, 0.171, 0.243 and 0.01 wt.%, respectively.

36 MATERIALS SCIENCE↗

Rate limitations of lime dissolution into coal ash slag

The rate-limiting mechanisms of lime dissolution from a solid pellet into coal ash slag and synthetic slag was investigated using an experiment involving a rotating cylinder of lime in a liquid slag bath at temperatures of 1450-1650{degree}C. Scanning electron microscopy (SEM) analysis of the slag composition around the lime cylinder was used to determine the nature of the boundary layer surrounding the pellet and the calcium concentration profile. Predictions using shrinking core models of a cylindrical pellet were compared to experimental results, suggesting that diffusion through the slag boundary layer and the change of the phase of lime from solid to liquid in the boundary layer combine to limit the process. These results indicate that a combination of controlling steps: diffusion through the boundary layer and the phase change of lime from solid to liquid, must be considered when predicting lime dissolution rates. 24 refs., 5 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Fiber-Optic Raman Probe for On-line EAF Slag Analysis

Here, in Electric Arc Furnace (EAF) steelmaking, the push for improved efficiency requires accurate analysis of the chemical composition of its slag system to control slag foaming, provide refractory protection, and maintain high furnace iron yield. Therefore, the ability to obtain real-time slag chemistry data would provide a useful tool to improve the control and efficiency of the process. The work reported here aims to assess the structure and chemistry of EAF slags at high temperatures using a portable fiber-optic Raman probe. As a result, the ability to relate Raman spectra peaks to chemistry and structure is demonstrated in experimental result with EAF slags at 1550°C.

47 OTHER INSTRUMENTATION↗

Evidence for carbon dioxide removal via enhanced rock weathering with steel slag, though not basalt, in a midwestern U.S. field trial

Enhanced weathering is an emergent pathway for permanent atmospheric carbon dioxide removal (CDR). However, despite a dramatic increase in academic and commercial research, there remain relatively few published examples of field evidence demonstrating the effectiveness of enhanced weathering. Here, we present results from a three-year field trial that evaluated steel slag and crushed basalt applied as amendments in a conventional agricultural system in the Midwestern United States. Steel slag applied to initially acidic soil increased porewater pH and alkalinity and increased soil pH and Ca-saturation. Together, changes in porewater chemistry and soil properties provide strong evidence for steel slag weathering and CDR. However, steel slag applied to soils with a neutral initial pH did not generate significant changes in soil or porewater chemistry. In addition, coarse-grained crushed basalt did not generate significant change in any of the soils. Strong acid effects were apparent in all 3 years of monitoring soil porewater chemistry. Overall, our results demonstrate clear evidence of CDR from applying steel slag amendments to acidic cropland soils while also highlighting the difficulty of greenhouse gas reduction accounting from enhanced weathering and the variable outcomes that can occur depending on feedstock and soil type.

Geosciences↗

Slags as Evidence for Copper Mining above Casaccia, Val Bregaglia (Central Alps)

Slags from the remote Mota Farun locality above Casaccia (Val Bregaglia, Swiss Alps) have been analyzed with scanning electron microscopy, X-ray powder diffraction and microfocus synchrotron X-ray diffraction to determine mineralogical composition and microstructures. Non-magnetic slag samples are largely composed of euhedral and dendritic iron-rich olivine in a glassy matrix. Locally there are zones with globular inclusions rich in bornite ((Cu5Fe)S4) and locally metallic copper. Some regions display dendritic pentlandite ((Fe,Ni)9S8). Magnetic samples are mainly composed of fayalite (Fe2SiO4) and wüstite (FeO), with minor magnetite (Fe3O4). The mineralogical composition indicates that slags were the product of copper smelting. The slag compositions and morphologies are analogous to slags described from the Oberhalbstein (Graubünden, Switzerland) and the Trentino Alps (Italy) which are attributed to metallurgical exploitations of the Late Bronze Age. While the origin of the ore could not be determined, it may be related to ore deposits of chalcopyrite in greenschists and serpentinites in the vicinity, such as Alp Tgavretga (Septimer Pass) and Val Perossa (Val Bregaglia).

58 GEOSCIENCES↗

Mechanism of Phase Formation in the Batch Mixtures for Slag-Bearing Glass Ceramics - 12207

Slag surrogate was produced from chemicals by heating to 900 deg. C and keeping at this temperature for 1 hr. The product obtained was intermixed with either sodium di-silicate (75 wt.% waste loading) or borax (85 wt.% slag loading). The mixtures were heat-treated within a temperature range of 25 to 1300 deg. C. The products were examined by X-ray diffraction and infrared spectroscopy. The products prepared at temperatures of up to 1000 deg. C contained both phase typical of the source slag and intermediate phases as well as phases typical of the materials melted at 1350 deg. C such as nepheline, britholite, magnetite and matrix vitreous phase. Vitrification process in batch mixtures consisting of slag surrogate and either sodium di-silicate or sodium tetraborate runs through formation of intermediate phases mainly silico-phosphates capable to incorporate Sm as trivalent actinides surrogate. Reactions in the batch mixtures are in the whole completed by ∼1000 deg. C but higher temperatures are required to homogenize the products. If in the borate-based system the mechanism is close to simple dissolution of slag constituents in the low viscous borate melt, then in the silicate-based system the mechanism was found to be much complicated and includes re-crystallization during melting with segregation of newly-formed nepheline type phase. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Gel nanostructure in alkali-activated binders based on slag and fly ash, and effects of accelerated carbonation

Binders formed through alkali-activation of slags and fly ashes, including ‘fly ash geopolymers’, provide appealing properties as binders for low-emissions concrete production. However, the changes in pH and pore solution chemistry induced during accelerated carbonation testing provide unrealistically low predictions of in-service carbonation resistance. The aluminosilicate gel remaining in an alkali-activated slag system after accelerated carbonation is highly polymerised, consistent with a decalcification mechanism, while fly ash-based binders mainly carbonate through precipitation of alkali salts (bicarbonates at elevated CO{sub 2} concentrations, or carbonates under natural exposure) from the pore solution, with little change in the binder gel identifiable by nuclear magnetic resonance spectroscopy. In activated fly ash/slag blends, two distinct gels (C–A–S–H and N–A–S–H) are formed; under accelerated carbonation, the N–A–S–H gel behaves comparably to fly ash-based systems, while the C–A–S–H gel is decalcified similarly to alkali-activated slag. This provides new scope for durability optimisation, and for developing appropriate testing methodologies. -- Highlights: •C-A-S-H gel in alkali-activated slag decalcifies during accelerated carbonation. •Alkali-activated fly ash gel changes much less under CO{sub 2} exposure. •Blended slag-fly ash binder contains two coexisting gel types. •These two gels respond differently to carbonation. •Understanding of carbonation mechanisms is essential in developing test methods.

36 MATERIALS SCIENCE↗

Sintering and collapse of synthetic coal ash and slag cones as observed through constant heating rate optical dilatometry

Ash agglomeration and slagging are responsible for costly maintenance problems in coal-fired boilers. Boiler design and operation rely on critical ash fusion temperatures defined by geometric criteria that explicitly ignore shrinkage or warping. Reproducibility of ash fusion test (AFT) results is known to be a major problem, given the subjective nature of some criteria used in critical temperature reporting. Decades of faulty predictions based on AFT data underscore the need for an objective measure of the likelihood for agglomeration and slagging as a function of coal ash composition and temperature. Heating microscopes and ash fusibility determinators are AFT instruments that are widely available and readily adapted for optical dilatometry of ash cones through digital image analysis. Optical dilatometry enables the continuous measurement of cone height and face area, and the calculation of changes in cone volume and density as a function of temperature during constant heating. A strong correlation was found between the sintering onset temperatures of two synthetic ash compositions measured through optical dilatometry and their corresponding solidus temperatures predicted through thermophysical modeling. The sintering onset temperatures of synthetic slag cones appears consistent with glass transition temperatures estimated using the Kauzmann-Beaman rule. Cone collapse is highly correlated with softening, hemispherical, and fluid temperatures for ash cones. Rapid changes in solid, liquid, and gas volume fractions near the collapse temperature suggest that a transition from capillary to slurry state may play an important role in triggering collapse. Slag cone collapse is better explained by a decrease in viscosity as a function of temperature in the glass working range. Furthermore, the sintering onset temperature and cone collapse temperature are readily understood through thermophysical modeling based on ash composition and provide two additional critical temperatures in the modeling of coal ash agglomeration and slagging.

01 COAL, LIGNITE, AND PEAT↗

Controlled evolution of rare earth phosphate in coal ash slag

Coal ash slag as a waste by-product, is generated from commercial processes that include gasification facilities, power plants, and steelmaking industries. Some is recycled into construction materials, insulation fibers, and used as a soil neutralizer, but the majority is still discarded. Coal ash slag exhibit trace amounts of critical materials including rare earth elements (REEs). An economically viable extraction of REEs from the coal ash would lower the production costs, addressing the availability and environmental concerns. In nature, most REEs exist as phosphate such as monazite but its synthetic evolution in coal ash slag has never been reported. In industrial processes, P may originate from coal, additives, and/or refractory liners. REEs may be extracted by first concentrating REEs into phosphates, sulphide, or fluorides [1], or carbonates [2]. In this work, P-enriched coal ash slag bearing REEs was first melted above 1600 °C, then crystallization behaviors in the melt during controlled cooling was studied. REE phosphate coprecipitated with mullite and hematite with mullite being the first crystal to form on cooling. The REEs were rejected from the molten slag, mullite, and hematite, and tended to segregate only to the phosphate phase with REE concentration as high as 58 wt.% in the structure.

Nakano, Jinichiro↗