Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SHEAR PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Computational Modeling of Hydraulic Properties of a Sheared Single Rock Fracture

Flow through a single mechanically sheared Marcellus shale fracture was investigated computationally and experimentally. To provide a better understanding of the variation of hydraulic and geometrical characteristics of a fracture subjected to shearing, coupled shear flow tests on the fracture for four shearing displacement steps under constant normal stress were performed. At the end of each shearing step, computed tomography (CT) scans with resolution 26.8 μm were obtained and the corresponding fracture geometries were evaluated. The CT images were used to generate full aperture maps of the fracture configuration. In addition, average aperture maps were also created by averaging the full-resolution data over 10 × 10 pixels, smoothing out fine structural details. Computational modeling of water flow through the fractures at different shearing steps was performed using a modified local cubic law approach and the 3D full Navier–Stokes equations with the use of the ANSYS-Fluent software. Both the average aperture maps and full maps were used in these simulations. The experimental pressure drops of the fracture at shearing step 1, which has very small apertures, poorly matched the numerical results, quite likely because the fracture structure was inadequately captured by the scanning resolution. Shearing typically increased the aperture height of the fracture, whose features were then better captured by the CT scan. Good agreement between the experimental data and the numerical results of the full map for shearing step 2 was observed. The simulations were performed for both full and average aperture maps, and the effects of scan resolution and surface roughness on the accuracy of the results were studied. The modified local cubic law and full Navier–Stokes simulations of the averaged map fracture were found to be in good agreement. It was conjectured that this was because the nonlinear losses were insignificant for the smoothed out averaged map fracture. Similar comparisons with those of the full map showed agreement in trends, but there were some quantitative differences. The averaged fracture map simulations also predicted lower pressure drops compared to the full map, particularly for high flow rates. These differences were due to the fine-scale geometrical complexity (surface roughness) of fracture geometry that affects the fluid flow in the fracture. In conclusion, an improved cubic law model was also proposed, and its accuracy was verified by comparing its predictions with those of the Navier–Stokes simulations.

58 GEOSCIENCES↗
NASA NTRS1976

Properties of spikelike shear flow reversals observed in the auroral plasma by Atmosphere Explorer C

A study of the characteristics of pairs of oppositely directed spikes in ionospheric convection velocities (or shear flow reversals), as first described by Gurnett, has been conducted by using data from Atmosphere Explorer C. These phenomena tend to occur near the large-scale reversal from sunward to antisunward convection on the nightside of the earth. Generally, the spikelike shear flow reversals involve electric field components along the spacecraft orbit that are directed toward the region between them, in which inverted V type electron precipitation is observed. This relationship between the electron precipitation and the electric field spikes is consistent with an upward-flowing field-aligned current that is fed by Pedersen currents from the adjacent regions of strong convection. In one case a divergent equivalent electric field structure was observed, that is, with the spikelike electric fields pointing away from the region in between, which in this case exhibited a sharp electron flux dropout. This opposite configuration may be an example of counterparts to inverted V structures existing in regions of downward-flowing field-aligned currents.

Burch, J. L.↗
DOE OSTI2018

On the validity of using the Debye model to quantitatively correlate the shear modulus with vibrational properties in cubic metals

The relationship between the shear modulus and the flexibility volume has been examined using molecular dynamics simulations in fifteen cubic metallic elements over a range of temperatures. Here we have observed a universal correlation, and identified the applicability range in which this correlation is quantitatively consistent with the prediction based on the Debye model. Deviation is observed for high modulus metals, and its origin is discussed in terms of the Debye assumptions regarding the vibrational mean squared displacement and the phonon density of states.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Effects of Shear Strain, Fabric, and Porosity Evolution on Elastic and Mechanical Properties of Clay-Rich Fault Gouge

The elastic and mechanical properties of fault gouge are key controls on fault zone stiffness, strength, damage, healing, and sliding stability. Clay minerals are prevalent in fault zones and have significant effects on friction, porosity, elastic properties, and shear fabric development. Although clay-rich gouges are well studied, the roles of porosity evolution and fabric formation in modulating elastic and mechanical properties are unclear. We have found that with progressive shear, the role of strain localization and fabric development may compete with densification to control the evolution of friction and elastic moduli. We report on a suite of double-direct shear experiments on synthetic gouge composed of 50% Ca-montmorillonite and 50% granular quartz at a normal stress of 25 MPa. We measure the coefficient of friction, porosity, P and S wave speeds, and bulk and shear moduli, and their evolution with shearing, to shear strains up to ~25. We find that the evolution of Vp, Vs, and elastic moduli are controlled by the interplay of porosity loss, shear fabric development, and particle contact stiffness. In general, V p , V s , and elastic moduli increase with shear strain and are accompanied by gradual densification and porosity loss. However, at intermediate shear strains (~2–8) a decrease in V p , V s , and elastic moduli is superimposed on this overall trend. Based on previous microstructural studies, we hypothesize that fabrics develop parallel to shear direction (perpendicular to wave propagation) over this range of strains, leading to reduced fault stiffness and competing with porosity loss as the dominant control on elastic properties.

58 GEOSCIENCES↗
DOE OSTI2021

Multi-Process Tooling

Decisions made early in the automotive design process influence material selection, which in turn dictates process selection and tool design. Because of tool build time and cost of tooling, the original path is not easily altered, even if there is compelling evidence that another material or process would be beneficial. This project focused on tool design that is agile enough to allow its use in multiple processes—injection, injection compression, and extrusion-compression. This tool design allows for the manufacture of components with the most efficient process or materials, without building multiple, single-process tools. The primary purpose of the Multi-Process Tool project was to physically demonstrate that a single, well-designed tool could be used to manufacture parts with a variety of materials that require different processes. A multi-process tool would be beneficial to providing data for any changes to the process since materials and processes can be interchanged without incurring additional tool cost(s). Battery tray parts, (representative of a multi-process tool, were successfully manufactured using various types of materials, such as fiber reinforced (carbon fiber and/or glass fibers, recycled carbon fibers), amorphous (PP, TPU), semi-crystalline (PA6, PA66), and crystalline (thermoset epoxy resin) polymers. Processing of the parts was achieved by injection molding, compression molding, compression overmolding, and injection overmolding. Specimens extracted from various locations on the battery tray parts were evaluated for mechanical properties (flexure and interlaminar shear strength properties). The results show that the tool can be used to produce parts from a wide range of materials and processes with no degradation of the physical or cosmetic properties.

42 ENGINEERING↗
NASA NTRS2002

Dynamics of Sheared Granular Materials

This work focuses on the properties of sheared granular materials near the jamming transition. The project currently involves two aspects. The first of these is an experiment that is a prototype for a planned ISS (International Space Station) flight. The second is discrete element simulations (DES) that can give insight into the behavior one might expect in a reduced-g environment. The experimental arrangement consists of an annular channel that contains the granular material. One surface, say the upper surface, rotates so as to shear the material contained in the annulus. The lower surface controls the mean density/mean stress on the sample through an actuator or other control system. A novel feature under development is the ability to 'thermalize' the layer, i.e. create a larger amount of random motion in the material, by using the actuating system to provide vibrations as well control the mean volume of the annulus. The stress states of the system are determined by transducers on the non-rotating wall. These measure both shear and normal components of the stress on different size scales. Here, the idea is to characterize the system as the density varies through values spanning dense almost solid to relatively mobile granular states. This transition regime encompasses the regime usually thought of as the glass transition, and/or the jamming transition. Motivation for this experiment springs from ideas of a granular glass transition, a related jamming transition, and from recent experiments. In particular, we note recent experiments carried out by our group to characterize this type of transition and also to demonstrate/ characterize fluctuations in slowly sheared systems. These experiments give key insights into what one might expect in near-zero g. In particular, they show that the compressibility of granular systems diverges at a transition or critical point. It is this divergence, coupled to gravity, that makes it extremely difficult if not impossible to characterize the transition region in an earth-bound experiment. In the DE modeling, we analyze dynamics of a sheared granular system in Couette geometry in two (2D) and three (3D) space dimensions. Here, the idea is to both better understand what we might encounter in a reduced-g environment, and at a deeper level to deduce the physics of sheared systems in a density regime that has not been addressed by past experiments or simulations. One aspect of the simulations addresses sheared 2D system in zero-g environment. For low volume fractions, the expected dynamics of this type of system is relatively well understood. However, as the volume fraction is increased, the system undergoes a phase transition, as explained above. The DES concentrate on the evolution of the system as the solid volume fraction is slowly increased, and in particular on the behavior of very dense systems. For these configurations, the simulations show that polydispersity of the sheared particles is a crucial factor that determines the system response. Figures 1 and 2 below, that present the total force on each grain, show that even relatively small (10 %) nonuniformity of the size of the grains (expected in typical experiments) may lead to significant modifications of the system properties, such as velocity profiles, temperature, force propagation, and formation shear bands. The simulations are extended in a few other directions, in order to provide additional insight to the experimental system analyzed above. In one direction, both gravity, and driving due to vibrations are included. These simulations allow for predictions on the driving regime that is required in the experiments in order to analyze the jamming transition. Furthermore, direct comparison of experiments and DES will allow for verification of the modeling assumptions. We have also extended our modeling efforts to 3D. The (preliminary) results of these simulations of an annular system in zero-g environment will conclude the presentation.

Kondic, Lou↗
DOE OSTI2019

Gyrokinetic simulations of m=0 mode in sheared flow Z-pinch

Axisymmetric stability properties of sheared flow Z-pinch plasmas are studied by making use of the gyrokinetic approximation in the long-wavelength limit. Numerical simulations are carried out with the high-order finite-volume code COntinuum Gyrokinetic Edge New Technology (COGENT) and are analyzed for the parameters characteristic of the FuZE experiment. Reduction of the linear growth rate with increasing shear is observed, and the results are elucidated by making use of a local dispersion relation analysis. In addition, COGENT simulations are compared with fully kinetic particle-in-cell simulations, and with an ideal magnetohydrodynamics (MHD) model. Good agreement between the gyrokinetic and fully kinetic results for the linear stability is found, with the gyrokinetic model requiring much less computational time due to its ability to step over particle gyroperiod. The ideal MHD model is found to be consistent with the kinetic models in the long-wavelength part of the spectra ($kρ_i$), while failing to adequately predict short-scale ($kρ_i$) stability. Here, $k$ is the axial wavelength vector and $ρ_i$ is the ion gyroradius.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2015

Shear strength characteristics of mechanically biologically treated municipal solid waste (MBT-MSW) from Bangalore

Highlights: • Shear strength properties of mechanically biologically treated municipal solid waste. • Effect of unit weight and particle size on the shear strength of waste. • Effect of particle size on the strength properties. • Stiffness ratio and the strength ratio of MSW. - Abstract: Strength and stiffness properties of municipal solid waste (MSW) are important in landfill design. This paper presents the results of comprehensive testing of shear strength properties of mechanically biologically treated municipal solid waste (MBT-MSW) in laboratory. Changes in shear strength of MSW as a function of unit weight and particle size were investigated by performing laboratory studies on the MSW collected from Mavallipura landfill site in Bangalore. Direct shear tests, small scale and large scale consolidated undrained and drained triaxial tests were conducted on reconstituted compost reject MSW samples. The triaxial test results showed that the MSW samples exhibited a strain-hardening behaviour and the strength of MSW increased with increase in unit weight. Consolidated drained tests showed that the mobilized shear strength of the MSW increased by 40% for a unit weight increase from 7.3 kN/m{sup 3} to 10.3 kN/m{sup 3} at 20% strain levels. The mobilized cohesion and friction angle ranged from 5 to 9 kPa and 8° to 33° corresponding to a strain level of 20%. The consolidated undrained tests exhibited reduced friction angle values compared to the consolidated drained tests. The friction angle increased with increase in the unit weight from 8° to 55° in the consolidated undrained tests. Minor variations were found in the cohesion values. Relationships for strength and stiffness of MSW in terms of strength and stiffness ratios are developed and discussed. The stiffness ratio and the strength ratio of MSW were found to be 10 and 0.43.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2019

Thermodynamic Relations among Isotropic Material Properties in Conditions of Plane Shear Stress

We present new general relationships among the material properties of an isotropic material kept in homogeneous stress conditions with hydrostatic pressure and plane shear. The derivation is not limited to the proximity of the zero shear-stress and -strain condition, which allows us to identify the relationship between adiabatic and isothermal shear compliances (inverse of the moduli of rigidity) along with new links, among others, between isobaric and isochoric shear thermal expansion coefficients and heat capacities at constant stress and constant shear strain. Such relationships are important for a variety of applications, including the determination of constitutive equations, the characterization of nanomaterials, and the identification of properties related to earthquakes precursors and complex media (e.g., soil) behavior. The results may be useful to investigate the behavior of materials during phase transitions involving shear or in non-homogeneous conditions within a local thermodynamic equilibrium framework.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Electric Field Tuning Molecular Packing and Electrical Properties of Solution-Shearing Coated Organic Semiconducting Thin Films

Recent improvements in solution-coated organic semiconductors (OSCs) evidence their high potential for cost-efficient organic electronics and sensors. Molecular packing structure determines the charge transport property of molecular solids. However, it remains challenging to control the molecular packing structure for a given OSC. Here, the application of alternating electric fields is reported to fine-tune the crystal packing of OSC solution-shearing coated at ambient conditions. First, a theoretical model based on dielectrophoresis is developed to guide the selection of the optimal conditions (frequency and amplitude) of the electric field applied through the solution-shearing blade during coating of OSC thin films. Next, electric field-induced polymorphism is demonstrated for OSCs with both herringbone and 2D brick-wall packing motifs in 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene and 6,13-bis(triisopropylsilylethynyl) pentacene, respectively. Favorable molecular packing can be accessible in some cases, resulting in higher charge carrier mobilities. In conclusion, this work provides a new approach to tune the properties of solution-coated OSCs in functional devices for high-performance printed electronics.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Microstructural characterization and mechanical property of active soldering anodized 6061 Al alloy using Sn-3.5Ag-xTi active solders

Active solders Sn-3.5Ag-xTi varied from x = 0 to 6 wt.% Ti addition were prepared by vacuum arc re-melting and the resultant phase formation and variation of microstructure with titanium concentration were analyzed using X-ray diffraction, optical microscopy and scanning electron microscopy. The Sn-3.5Ag-xTi active solders are used as metallic filler to join with anodized 6061 Al alloy for potential applications of providing a higher heat conduction path. Their joints and mechanical properties were characterized and evaluated in terms of titanium content. The mechanical property of joints was measured by shear testing. The joint strength was very dependent on the titanium content. Solder with a 0.5 wt.% Ti addition can successfully wet and bond to the anodized aluminum oxide layers of Al alloy and posses a shear strength of 16.28 {+-} 0.64 MPa. The maximum bonding strength reached 22.24 {+-} 0.70 MPa at a 3 wt.% Ti addition. Interfacial reaction phase and chemical composition were identified by a transmission electron microscope with energy dispersive spectrometer. Results showed that the Ti element reacts with anodized aluminum oxide to form Al{sub 3}Ti-rich and Al{sub 3}Ti phases at the joint interfaces. - Highlights: Black-Right-Pointing-Pointer Active solder joining of anodized Al alloy needs 0.5 wt.% Ti addition for Sn-3.5Ag. Black-Right-Pointing-Pointer The maximum bonding strength occurs at 3 wt.% Ti addition. Black-Right-Pointing-Pointer The Ti reacts with anodized Al oxide to form Al{sub 3}Ti-rich and Al{sub 3}Ti at joint interface.

36 MATERIALS SCIENCE↗
DOE OSTI2015

FP-LAPW based investigation of structural, electronic and mechanical properties of CePb{sub 3} intermetallic compound

A theoretical study of structural, electronic, elastic and mechanical properties of CePb{sub 3} intermetallic compound has been investigated systematically using first principles density functional theory. The calculations are carried out within the three different forms of generalized gradient approximation (GGA) and LSDA for the exchange correlation potential. The ground state properties such as lattice parameter (a{sub 0}), bulk modulus (B) and its pressure derivative (B′) are calculated and obtained lattice parameter of this compound shows well agreement with the experimental results. We have calculated three independent second order elastic constants (C{sub 11}, C{sub 12} and C{sub 44}), which has not been calculated and measured yet. From energy dispersion curves, it is found that the studied compound is metallic in nature. Ductility of this compound is analyzed using Pugh’s criteria and Cauchy's pressure (C{sub 11}-C{sub 12}). The mechanical properties such as Young's modulus, shear modulus, anisotropic ratio, Poison's ratio have been calculated for the first time using the Voigt–Reuss–Hill (VRH) averaging scheme. The average sound velocities (v{sub m}), density (ρ) and Debye temperature (θ{sub D}) of this compound are also estimated from the elastic constants.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Kelvin-Helmholtz instability in non-Newtonian complex plasma

The Kelvin-Helmholtz (KH) instability is studied in a non-Newtonian dusty plasma with an experimentally verified model [Phys. Rev. Lett. 98, 145003 (2007)] of shear flow rate dependent viscosity. The shear flow profile used here is a parabolic type bounded flow. Both the shear thinning and shear thickening properties are investigated in compressible as well as incompressible limits using a linear stability analysis. Like the stabilizing effect of compressibility on the KH instability, the non-Newtonian effect in shear thickening regime could also suppress the instability but on the contrary, shear thinning property enhances it. A detailed study is reported on the role of non-Newtonian effect on KH instability with conventional dust fluid equations using standard eigenvalue analysis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗