SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Flight and simulator study of handling qualities of deflected slipstream STOL seaplane having four propellers and boundary layer control
Investigations were made to determine the cowling and cooling characteristics of the Ranger V-770-8 engine installation in an observation seaplane. Final cowl configurations possessed ample engine and oil-cooler pressure drops for cooling in the critical normal-power climb condition with any of the three baffle configurations tested. The indicated critical Mach number of the cowling was found to be 0.70 as determined by the pressure on the lower lip of the inlet.
Comprehensive tests were made to compare the performance of the F-5-L Boat Seaplane fitted with direct drive and Liberty engines. Details are given on the test conditions. The conclusions of the comparison tests follow. 1) An F-5-L with geared engines takes off in approximately 90 percent of the time required for the same airplane with standard direct drive engines. An F-5-L with geared engines climbs in 20 minutes to an altitude approximately 20 percent greater than that obtained with the standard direct drive on the same airplane. 3) There is a large difference between the climbs of the two airplanes of the same type. This difference will always be more pronounced when the climb is normally slow. In the case of the F-5-L airplanes under construction, it is of the order of a 10 percent difference in altitude on a 20 minute climb. 4) The maximum speed of an F-5-L with geared engines is about 3.5 percent greater than the maximum speed of the same airplane with standard direct drive engines (at the same engine r.p.m.). 5) The fuel consumption is probably less effected by the type of drive than by inherent differences in the performance of different airplanes.
This report provides a list of landing locations for seaplanes on the Atlantic coast of the United States and the facilities and services located there.
Tests were conducted to investigate the possibility of a serious accident arising from unintentional contact with the water in substantially horizontal flight at high speed. Referring to vector diagrams on Figure 2, it will be seen that a very dangerous condition may arise if the float be allowed to come in contact with the water at high speeds as, for example, when flying at high speed just above the water. The initial diving moment due to suction and drag combined may be great enough to cause the seaplane to nose under before the pilot is able to control the motion. The same test data indicate clearly the existence of forces and moments tending to produce the phenomenon observed by Mr. Carroll (Technical Note No. 287) when the maneuver is carried out at lower speeds, as in a landing.
Data obtained at the N.A.C.A. tank from tests on the models of three flying-boat hulls - N.A.C.A. models 11-A, 16, and 22 - are used to demonstrate the effect of trim angle on water resistance. A specific example is taken, and data from Model 11-A are used to show that the trim angle giving the minimum water resistance will give minimum total air-plus-water resistance. Total-resistance curves for best trimmed angles and other angles are compared for the same example. The effect of wind on best trim angles and upon the take-off and run is shown by the working of an example. The possibility of using tank data on trim angles as aid in piloting is discussed, and an instrument for use in determining the trim angle of seaplanes is described. The importance of maintaining the best trim angle throughout the take-off is indicated.
The increase in the frictional resistance of a surface caused by the presence of rivet heads was determined by towing four planing surfaces of the same dimensions. One surface was smooth and represented a surface without rivet heads or one with perfectly flush countersunk rivets. The other three surfaces were each fitted with the same number of full-size rivet heads but of a different type arranged in the same pattern on each surface. The surfaces were towed at speeds representative of the high water speeds encountered by seaplanes during take-off and the range of Reynolds Number covered by the test was from 4 x 10(exp 6) to 18 x 10(exp 6). The rivet heads investigated were oval countersunk, brazier, and round for rivets having shanks 5/32 inch in diameter. The oval countersunk heads were sunk below the surface by dimpling the plating around them. The results of the tests showed that, for the rivet heads investigated, the increase in the friction coefficient of the surface is directly proportional to the height of the rivet head. The order of merit in regard to low resistance is flush countersunk, oval countersunk (whether sunk below the surface or not), brazier, and round.
The drag of five models of side floats was measured in the N.A.C.A. 7- by 10-foot wind tunnel. The most promising method of reducing the drag of floats indicated by these tests is lowering the angle at which the floats are rigged. The addition of a step to a float does not always increase the drag in the flying range, floats with steps sometimes having lower drag than similar floats without steps. Making the bow chine no higher than necessary might result in a reduction in air drag because of the lower angle of pitch of the chines. Since side floats are used formally to obtain lateral stability when the seaplane is operating on the water at slow speeds or at rest, greater consideration can be given to factors affecting aerodynamic drag than is possible for other types of floats and hulls.
During a flight with a Van Berkel W. B. seaplane it was observed that the wing could perform violent oscillations. A theoretical and experimental investigation led to the conclusion, that in some cases an unstable oscillation of the wing-aileron system under the influence of the elastic and aerodynamic forces is possible without further external causes.
In the present article, several suggestions will be made for shortening the otherwise long take-off distance. For the numerical verification of the process, I will use a graphic method for determining the take-off distance of seaplanes.
This is the third in a series of investigations of the water pressures on seaplane floats and hulls, and completes the present program. It consisted of determining the water pressures and accelerations on a Curtiss H-16 flying boat during landing and taxiing maneuvers in smooth and rough water.
The NACA model 40 series of flying-boat hull models consists of 2 forebodies and 3 afterbodies combined to provide several forms suitable for use in small marine aircraft. One forebody is the usual form with hollow bow sections and the other has a bottom surface that is completely developable from bow to step. The afterbodies include a short pointed afterbody with an extension for the tail surfaces, a long afterbody similar to that of a seaplane float but long enough to carry the tail surfaces, and a third obtained by fitting a second step in the latter afterbody. The various combinations were tested in the NACA Tank by the general method over a suitable range of loadings. Fixed-trim tests were made for all speeds likely to be used and free-to-trim tests were made at low speeds to slightly beyond the hump speed. The characteristics of the hulls at best trim angles have been deduced from the data of the tests at fixed trim angles and are given in the form of nondimensional coefficients applicable to any size hull.
Flight tests were conducted on the OS2U-2 seaplane with simple circular-arc-type ailerons directly connected to the actuating torque tube. Two aileron test installations were made, differing only in the inclination of the projecting surface with the wing's upper surface. The lateral-control characteristics of the airplane were determined from data obtained in stalls and rudder-fixed aileron rolls. The revised ailerons were deficient in maximum rolling effectiveness, but were capable of controlling the rolling tendencies of the airplane near the stall.
Tests were conducted on hydrofoil assemblies approximating an arrangement for use under seaplanes or surface boats. A series of hydrofoils, each supported by two struts, was towed at various depths ranging from partial submersions to a depth of 5-chord lengths. At depths greater than 4 or 5 chords, the influence of the surface of the water is small; hydrofoils operating at low speed will have characteristics similar to those of airfoils of the same section.
Experiments with planing surfaces are fundamental, hydrodynamic researches for the purpose of obtaining the most favorable forms for planing boats, flying boats, and seaplane floats, with respect to water resistance and seaworthiness.
The present report deals with the processes accompanying the planing of a planing boat or a seaplane on water . The study is largely based upon theoretical investigations; mathematical problems and proofs are not discussed. To analyze theoreticaly actual planing processes, giving due consideration to all aspects of the problem, is probably not possible. The theories therefore treat various simple limiting cases, which in their entirety give a picture of the planing processes and enable the interpretation of the experimental results. The discussion is concerned with the stationary planing attitude: the boat planes at a constant speed V on an originally smooth surface.
The hydrodynamic characteristics of an aerodynamically refined planing-tail hull were determined from dynamic model tests in Langley tank no. 2. Stable take-off could be made for a wide range of locations of the center of gravity. The lower porpoising limit peak was high, but no upper limit was encountered. Resistance was high, being about the same as that of float seaplanes. A reasonable range of trims for stable landings was available only in the aft range of center-of-gravity locations.
Explore the source record for details and available documents.