Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Rarefied Flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Assessment of chemical nonequilibrium in rarefied hypersonic flow

Calculations are presented of chemical nonequilibrium in the rarefied hypersonic flowfields surrounding reentering spacecraft in the upper atmosphere. The direct simulation Monte Carlo method is the solution technique employed. Methods by which chemical reactions are included in this simulation scheme are focused upon. In particular, the coupling of vibrational and dissociative nonequilibrium is investigated. The assumption of a fully excited mode has very little effect on the calculated results when the vibrational mode does not contribute to the energy available for reaction. A steric factor for dissociative reactions is developed which includes the vibrational energy of the dissociating molecule. Calculations are presented for the flow along the stagnation streamline of a blunt body for conditions representative of the entry and exit phases of the Aeroassisted Flight Experiment vehicle at an altitude of 90 km. It is found that both the flow properties and surface quantities are significantly affected by the introduction of the steric factor.

Boyd, Iain D.↗

Planar Laser-Induced Iodine Fluorescence Measurements in Rarefied Hypersonic Flow

A planar laser-induced fluorescence (PLIF) technique is discussed and applied to measurement of time-averaged values of velocity and temperature in an I(sub 2)-seeded N(sub 2) hypersonic free jet facility. Using this technique, a low temperature, non-reacting, hypersonic flow over a simplified model of a reaction control system (RCS) was investigated. Data are presented of rarefied Mach 12 flow over a sharp leading edge flat plate at zero incidence, both with and without an interacting jet issuing from a nozzle built into the plate. The velocity profile in the boundary layer on the plate was resolved. The slip velocity along the plate, extrapolated from the velocity profile data, varied from nearly 100% down to 10% of the freestream value. These measurements are compared with results of a DSMC solution. The velocity variation along the centerline of a jet issuing from the plate was measured and found to match closely with the correlation of Ashkenas and Sherman. The velocity variation in the oblique shock terminating the jet was resolved sufficiently to measure the shock wave thickness.

Cecil, Eric↗

The Shuttle Orbiter high resolution accelerometer package experiment - Preliminary flight results

A description of the High Resolution Accelerometer Package (HiRAP) experiment, designed to measure rarefied flow aerodynamic accelerations, is given. The ground test calibration factors, as well as post-flight data processing techniques to extract aerodynamic accelerations, are discussed and applied to the recorded reentry data of the recent STS-6 Shuttle Orbiter flight. The ratio of the measured normal-to-axial aerodynamic accelerations during reentry is used to obtain the first flight measurement of the lift-to-drag ratio (L/D) of a winged entry vehicle in the rarefied flow flight regime. The preliminary result for the free-molecule flow L/D is 0.10 + or - 0.03. The initial flight results on L/D are compared with current predictions which are based upon theoretical and empirical considerations. The measured free-molecule flow L/D value is higher than predicted by a factor of about three, indicating that surface reflection is not completely diffuse as currently assumed. In the rarefied flow transition regime, the Shuttle data book-bridging formula fits the flight data adequately. Upper altitude density profiles are also deduced from the measurements and presented. The density profiles show a wave phenomena with amplitude of about 60 percent, relative to a standard model.

Blanchard, R. C.↗

Rarefield-Flow Shuttle Aerodynamics Flight Model

A model of the Shuttle Orbiter rarefied-flow aerodynamic force coefficients has been derived from the ratio of flight acceleration measurements. The in-situ, low-frequency (less than 1Hz), low-level (approximately 1 x 10(exp -6) g) acceleration measurements are made during atmospheric re-entry. The experiment equipment designed and used for this task is the High Resolution Accelerometer Package (HiRAP), one of the sensor packages in the Orbiter Experiments Program. To date, 12 HiRAP re-entry mission data sets spanning a period of about 10 years have been processed. The HiRAP-derived aerodynamics model is described in detail. The model includes normal and axial hypersonic continuum coefficient equations as function of angle of attack, body-flap deflection, and elevon deflection. Normal and axial free molecule flow coefficient equations as a function of angle of attack are also presented, along with flight-derived rarefied-flow transition bridging formulae. Comparisons are made between the aerodynamics model, data from the latest Orbiter Operational Aerodynamic Design Data Book, applicable computer simulations, and wind-tunnel data.

Blanchard, Robert C.↗

Study of Plume Impingement Effects in the Lunar Lander Environment

Plume impingement effects from the descent and ascent engine firings of the Lunar Lander were analyzed in support of the Lunar Architecture Team under the Constellation Program. The descent stage analysis was performed to obtain shear and pressure forces on the lunar surface as well as velocity and density profiles in the flow field in an effort to understand lunar soil erosion and ejected soil impact damage which was analyzed as part of a separate study. A CFD/DSMC decoupled methodology was used with the Bird continuum breakdown parameter to distinguish the continuum flow from the rarefied flow. The ascent stage analysis was performed to ascertain the forces and moments acting on the Lunar Lander Ascent Module due to the firing of the main engine on take-off. The Reacting and Multiphase Program (RAMP) method of characteristics (MOC) code was used to model the continuum region of the nozzle plume, and the Direct Simulation Monte Carlo (DSMC) Analysis Code (DAC) was used to model the impingement results in the rarefied region. The ascent module (AM) was analyzed for various pitch and yaw rotations and for various heights in relation to the descent module (DM). For the ascent stage analysis, the plume inflow boundary was located near the nozzle exit plane in a region where the flow number density was large enough to make the DSMC solution computationally expensive. Therefore, a scaling coefficient was used to make the DSMC solution more computationally manageable. An analysis of the effectiveness of this scaling technique was performed by investigating various scaling parameters for a single height and rotation of the AM. Because the inflow boundary was near the nozzle exit plane, another analysis was performed investigating three different inflow contours to determine the effects of the flow expansion around the nozzle lip on the final plume impingement results.

Marichalar, Jeremiah↗

Hypersonic flow simulations using DSMC (direct simulation Monte Carlo)

A review of the DSMC method of Bird is presented. The DSMC method provides the capability of simulating real gas flows in the rarefied flow regime. Recent developments and applications of the method for hypersonic flows are reported for both ground-based tests and during entry. Results obtained using both axisymmetric and 3D codes are included.

Moss, James N.↗

Parallel implementation of a particle simulation for modeling rarefied gas dynamic flow

When the conditions of flow are rarefied and hypersonic, a more suitable alternative to the use of the Navier-Stokes equations for developing a numerical solution is the Direct Simulation Monte Carlo method (DSMC), a method of simulation which employs a large number of particles in modeling a rarefied gas. The performance of a parallel DSMC code developed for the Intel iPSC/860 Touchstone Gamma prototype computer is studied and the scaleup is found to be very nearly over the range of 16-128 processors.

Fallavollita, M. A.↗

Simulated rarefied aerodynamics of the Magellan spacecraft during aerobraking

Aerodynamic loads upon the Magellan spacecraft during aerobraking through the atmosphere of Venus are computed at off-design attitudes with a direct simulation Monte Carlo (DSMC) particle method. Simulated rarefied flows at nominal altitudes near 140 km and an entry speed of 8.6 km/s were compared to simulated and analytic free molecular results. Aerodynamic moments, forces, and heating for rarefied entry at all attitudes were 7-10 percent below free molecular results. All moments acted to restore the vehicle to its nominal zero-pitch, zero-yaw attitude. Suggested canting of the solar panels is an innovative configuration to assess gas-surface interaction during aerobraking. The resulting roll torques about the central body-axis as predicted in rarefied flow simulations were nearly twice that predicted for free molecular flow, although differences became less distinct for thermal accommodation coefficients well below unity. Roll torques increased dramatically with reduced accommodation coefficients employed in the simulation. In the DSMC code, periodic free-molecule boundary conditions and a coarse computational grid and body resolution served to minimize the simulation size and cost while retaining solution validity.

Haas, Brian L.↗

Shuttle Upper Atmosphere Mass Spectrometer Experimental Flight Results

Calibrated pressure measurements for species with mass-to-charge ratios up to 50 amu/e(-) were obtained trom the shuttle upper atmosphere mass spectrometer experiment during re-entry on the STS-35 mission. The principal experimental objective is to obtain measurements of freestream density in the hypersonic rarefied flow flight regime. Data were collected from 180 to about 87 km. However, data above 115 km were contaminated from a source of gas emanating from pressure transdueers connected in parallel to the mass spectrometer. At lower altitudes, the pressure transducer data are compared to the mass spectrometer total pressure with excellent agreement. Near the orifice entrance, a significant amount of CO2 was generated from chemical reactions. The freestream density in the rarefied flow flight regime is calculated using an orifice pressure coefficient model based upon direct simulation Monte Carlo results. This density, when compared with the 1976 U.S. Standard Atmosphere model, exhibits the wavelike nature seen on previous flights using accelerometry. Selected spectra are presented at higher altitudes (320 km) showing the effects of the ingestion of gases from a forward fuselage fuel dump.

Blanchard, R. C.↗

Rarefied xenon flow in orificed hollow cathodes

A parametric study is conducted to quantify the effect of the keeper electrode geometry on the xenon neutral flow quantities within orificed hollow cathodes, prior to ignition. The keeper impinges directly on the flow out of the cathode orifice and its geometry influences the product between the pressure in the orifice–keeper region and the cathode-to-keeper distance. A representative cathode is simulated using the Direct Simulation Monte Carlo method. The numerical model is first validated with computational results from the literature. A parametric study is then conducted. Parameters include the cathode pressure–diameter in the range of 1–5 Torr cm and the following geometric ratios (and ranges): cathode orifice-to-inner radii (0.1–0.7), keeper orifice-to-cathode orifice radii (1–5), and keeper distance-to-cathode-orifice diameter (0.5–10). It is found that, if both keeper and cathode have identical orifice radii, the flow remains subsonic in the orifice-to-keeper region. In most cases, however, the flow becomes underexpanded and supersonic, and the static pressure within the orifice-to-keeper region is, on average, 4% that of the upstream pressure value. The orifice–keeper region pressure increases with either a decrease in the keeper orifice diameter or an increase in the distance between cathode and keeper, in agreement with literature data. Both trends are explained through conservation laws. A statistical study of numerical results reveals that the ratio of ignition-to-nominal mass flow rates has a most probable value of 50, which suggests that heaterless cathode ignition at a minimum DC voltage may be achieved by increasing the input mass flow rate by a factor of 50.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Computer simulation of supersonic rarefied gas flow in the transition region, about a spherical probe; a Monte Carlo approach with application to rocket-borne ion probe experiments

This report describes a Monte Carlo simulation of transition flow around a sphere. Conditions for the simulation correspond to neutral monatomic molecules at two altitudes (70 and 75 km) in the D region of the ionosphere. Results are presented in the form of density contours, velocity vector plots and density, velocity and temperature profiles for the two altitudes. Contours and density profiles are related to independent Monte Carlo and experimental studies, and drag coefficients are calculated and compared with available experimental data. The small computer used is a PDP-15 with 16 K of core, and a typical run for 75 km requires five iterations, each taking five hours. The results are recorded on DECTAPE to be printed when required, and the program provides error estimates for any flow field parameter.

Horton, B. E.↗

Apparatus for calibration of on-board instruments and laboratory modelling of rarefied plasma flows past models

Problems of laboratory simulation of artificial earth satellite flight conditions in the ionosphere are examined, and a setup capable of reproducing the basic parameters of ion flows (with energies of 5-10 eV, energy spectrum width approximately 2x5 eV, and an intensity of 10 to the minus 8th power a/cm/2) past measurement instruments and satellite models is described. Possibilities for further improvement of the apparatus are discussed.

Yevlanov, Y. N.↗

Numerical simulations of rarefied reentry flows

A review of recent calculations obtained with Bird's direct simulation Monte Carlo (DSMC) method is presented for the transitional flowfield encountered at reentry conditions. Consequently, the emphasis is the real-gas effects resulting from a highly energetic nonequilibrium flow. The DSMC calculations for both wide-angle and slender bodies are compared with continuum calculations. The wide-angle body calculations simulate the windward nose of the Shuttle Orbiter and projected aeroassisted orbital transfer vehicles. For the slender, blunted configurations, both two-dimensional and axisymmetric results are presented. Comparisons between the DSMC and continuum calculations show the altitude range where differences in flowfield structure and surface quantities become significant.

Moss, James N.↗

Rotational and vibrational nonequilibrium effects in rarefied, hypersonic flow

Results are reported for an investigation into the methods by which energy transfer is calculated in the Direct Simulation Monte Carlo method. Description is made of a recently developed energy exchange model that deals with the translational and rotational modes. A new model for simulating the transfer of energy between the translational and vibrational modes is also explained. This model allows the vibrational relaxation time to follow the temperature dependence predicted by the Landau-Teller theory at moderate temperatures. For temperatures in excess of about 8000K the vibrational model is extended to include an empirical result for the relaxation time. The effect of introducing these temperature dependent collision numbers into the DSMC technique is assessed by making calculations representative of the stagnation streamline of a hypersonic space vehicle. Both thermal and chemical nonequilibrium effects are included while the flow conditions have been chosen such that ionization and radiation may be neglected. The introduction of these new models is found to significantly affect the degree of thermal nonequilibrium observed in the flowfield. Larger, and more widely ranging, differences in the results obtained with the different energy exchange probabilities are found when a significant amount of internal energy is included in the calculation of chemical nonequilibrium.

Boyd, Iain D.↗

Rotational-translational energy transfer in rarefied nonequilibrium flows

A new model for simulating the transfer of energy between the translational and rotational modes is derived for a homogeneous gas of diatomic molecules. The model has been developed specifically for use in discrete particle simulation methods where molecular motion and intermolecular collisions are treated at the molecular level. A temperature dependence is introduced which has been predicted by theory and observed in experiment. The new model is applied to the relaxation of rotational temperature, and is found to produce significant differences in comparison with the model normally employed at both high and low temperatures. Calculations have also been performed for a Mach 7 normal shock wave.

Boyd, Iain D.↗

One-dimensional hybrid continuum/particle simulation approach for rarefied hypersonic flows

A hybrid numerical technique, based on local application of continuum and particle methods, is applied to the one-dimensional normal shock structure in a monatomic gas. The methods are coupled iteratively via a flux boundary condition in a region where both are applicable. The validity of each method through the shock structure is quantified. The physical and numerical aspects of coupling are discussed and a variety of coupling methods are assessed. Results are presented to show the improvement in computational efficiency available via the hybrid approach.

Wadsworth, D. C.↗

Molecular dynamics computations of two dimensional supersonic rarefied gas flow past blunt bodies

This paper presents results of molecular dynamics computations of supersonic flow past a circular cylinder and past a flat plate perpendicular to a supersonic stream. The results are for Mach numbers of approximately 5 and 10, for several Knudsen numbers and several ratios of surface to free stream temperatures. A special feature of the computations is the use of relatively small numbers of particles in the molecular dynamics simulation, and an examination of the adequacy of using small numbers of particles to obtain physically useful results.

Greber, Isaac↗

A shock-layer theory based on thirteen-moment equations and DSMC calculations of rarefied hypersonic flows

Grad's thirteen-moment equations are applied to the flow behind a bow shock under the formalism of a thin shock layer. Comparison of this version of the theory with Direct Simulation Monte Carlo calculations of flows about a flat plate at finite attack angle has lent support to the approach as a useful extension of the continuum model for studying translational nonequilibrium in the shock layer. This paper reassesses the physical basis and limitations of the development with additional calculations and comparisons. The streamline correlation principle, which allows transformation of the 13-moment based system to one based on the Navier-Stokes equations, is extended to a three-dimensional formulation. The development yields a strip theory for planar lifting surfaces at finite incidences. Examples reveal that the lift-to-drag ratio is little influenced by planform geometry and varies with altitudes according to a 'bridging function' determined by correlated two-dimensional calculations.

Cheng, H. K.↗