Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REFLECTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Main-Reflector Manufacturing Technology for the Deep Space Optical Communications Ground Station

The Deep Space Network (DSN) has plans to develop a 10-m-diameter optical communications receiving station. The system uses the direct detection technique, which has much different requirements from a typical astronomical telescope. The receiver must operate in daylight and nighttime conditions. This imposes special requirements on the optical system to reject stray light from the Sun and other sources. One of the biggest challenges is designing a main-reflector surface that meets these requirements and can be produced at a reasonable cost. The requirements for the performance of the reflector are presented. To date, an aspherical primary reflector has been assumed. A reflector with a spherical reflector has a major cost advantage over an aspherical design, with no sacrifice in performance. A survey of current manufacturing techniques for optical mirrors of this type was performed. Techniques including solid glass, lightweight glass, diamond-turned aluminum, and composite mirrors were investigated.

Britcliffe, M. J.↗

Nanolaminate Membranes as Cylindrical Telescope Reflectors

A document discusses a proposal to use axially stretched metal nanolaminate membranes as lightweight parabolic cylindrical reflectors in the Dual Anamorphic Reflector Telescope (DART) - a planned spaceborne telescope in which the cylindrical reflectors would be arranged to obtain a point focus. The discussion brings together a combination of concepts reported separately in several prior NASA Tech Briefs articles, the most relevant being "Nanolaminate Mirrors With Integral Figure-Control Actuators" NPO -30221, Vol. 26, No. 5 (May 2002), page 90; and "Reflectors Made From Membranes Stretched Between Beams" NPO -30571, Vol. 33, No. 10 (October 2009), page 11a. The engineering issues receiving the greatest emphasis in the instant document are (1) the change in curvature associated with the Poisson contraction of a stretched nanolaminate reflector membrane and (2) the feasibility of using patches of poly(vinylidene fluoride) on the rear membrane surface as piezoelectric actuators to correct the surface figure for the effect of Poisson contraction and other shape errors.

Dooley, Jennifer↗

Weighted SAW reflector gratings for orthogonal frequency coded SAW tags and sensors

Weighted surface acoustic wave reflector gratings for coding identification tags and sensors to enable unique sensor operation and identification for a multi-sensor environment. In an embodiment, the weighted reflectors are variable while in another embodiment the reflector gratings are apodized. The weighting technique allows the designer to decrease reflectively and allows for more chips to be implemented in a device and, consequently, more coding diversity. As a result, more tags and sensors can be implemented using a given bandwidth when compared with uniform reflectors. Use of weighted reflector gratings with OFC makes various phase shifting schemes possible, such as in-phase and quadrature implementations of coded waveforms resulting in reduced device size and increased coding.

Puccio, Derek↗

Solar Thermal Vacuum Test of Deployable Astromesh Reflector

On September 10, 2008, a 36-hour Solar Thermal Vacuum Test of a 5m deployable mesh reflector was completed in JPL's 25' Space Simulator by the Advanced Deployable Structures Group at JPL. The testing was performed under NASA's Innovative Partnership Program (IPP) as a risk reduction effort for two JPL Decadal Survey Missions: DESDynI and SMAP. The 5.0 m aperture Astromesh reflector was provided by Northrop Grumman Aerospace Systems (NGAS) Astro Aerospace, our IPP industry partner. The testing utilized a state-of-the-art photogrammetry system to measure deformation of the reflector under LN2 cold soak, 0.25 Earth sun, 0.5 sun and 1.0 sun. An intricate network of thermocouples (approximately 200 in total) was used to determine the localized temperature across the mesh as well as on the perimeter truss of the reflector. Half of the reflector was in a fixed shadow to maximize thermal gradients. A mobility system was built for remotely actuating the cryo-vacuum capable photogrammetry camera around the circumference of the Solar Simulator. Photogrammetric resolution of 0.025 mm RMS (0.001") was achieved over the entire 5 meter aperture for each test case. The data will be used for thermo-elastic model correlation and validation, which will benefit the planned Earth Science Missions.

Photogrammetry↗

Cryolite Overcoated Aluminum Reflectors for Far-Ultraviolet Spectroscopy

Aluminum (Al) mirrors are conventionally protected with metal-fluoride coatings (e.g., MgF 2 , LiF, or AlF 3 ) immediately after deposition to prevent oxidation and preserve its far-ultraviolet (FUV) spectral efficiency. However, the resulting FUV reflectance of the aluminum reflector is limited by the metal-fluoride overcoat film index of refraction, morphology, stoichiometry, and its absorption cut-off in the lower end of the FUV spectra. Cryolite (sodium hexafluoroaluminate, Na 3 AlF 6 ) emerges as a potential candidate to preserve the aluminum FUV reflectance due to its relatively lower index of refraction in the visible to ultraviolet; therefore, allowing for the thin-film design of highly spectral efficient reflectors over a wide spectral range. We investigate the use of cryolite in aluminum reflector FUV coating design. The deposited aluminum reflector overcoated with cryolite will be examined in terms of spectral efficiency and environmental durability. The deposited cryolite overcoat will be evaluated in terms of optical constants and structural properties. Preliminary results have shown that the use of cryolite as an overcoat to protect aluminum would yield unprecedented results as an optimal Hydrogen Lyman-alpha (HLyα) spectral line reflector, with experimental reflectance values >96%.

optical coating↗

Cryolite Overcoated Aluminum Reflectors for Far-Ultraviolet Spectroscopy

Aluminum (Al) mirrors are conventionally protected with metal-fluoride coatings (e.g., MgF2, LiF, or AlF3) immediately after deposition to prevent oxidation and preserve its far-ultraviolet (FUV) spectral efficiency. However, the resulting FUV reflectance of the aluminum reflector is limited by the metal-fluoride overcoat film index of refraction, morphology, stoichiometry, and its absorption cut-off in the lower end of the FUV spectra. Cryolite (sodium hexafluoroaluminate, Na3AlF6) emerges as a potential candidate to preserve the aluminum FUV reflectance due to its relatively lower index of refraction in the visible to ultraviolet; therefore, allowing for the thin-film design of highly spectral efficient reflectors over a wide spectral range. We investigate the use of cryolite in aluminum reflector FUV coating design. The deposited aluminum reflector overcoated with cryolite will be examined in terms of spectral efficiency and environmental durability. The deposited cryolite overcoat will be evaluated in terms of optical constants and structural properties. Preliminary results have shown that the use of cryolite as an overcoat to protect aluminum would yield unprecedented results as an optimal Hydrogen Lyman-alpha (HLyα) spectral line reflector, with experimental reflectance values >96%.

optical coatings↗

Photovoltaic generator with a spherical imaging lens for use with a paraboloidal solar reflector

The invention is a generator for photovoltaic conversion of concentrated sunlight into electricity. A generator according to the invention incorporates a plurality of photovoltaic cells and is intended for operation near the focus of a large paraboloidal reflector pointed at the sun. Within the generator, the entering concentrated light is relayed by secondary optics to the cells arranged in a compact, concave array. The light is delivered to the cells at high concentration, consistent with high photovoltaic conversion efficiency and low cell cost per unit power output. Light enters the generator, preferably first through a sealing window, and passes through a field lens, preferably in the form of a full sphere or ball lens centered on the paraboloid focus. This lens forms a concentric, concave and wide-angle image of the primary reflector, where the intensity of the concentrated light is stabilized against changes in the position of concentrated light entering the generator. Receiving the stabilized light are flat photovoltaic cells made in different shapes and sizes and configured in a concave array corresponding to the concave image of a given primary reflector. Photovoltaic cells in a generator are also sized and interconnected so as to provide a single electrical output that remains high and stable, despite aberrations in the light delivered to the generator caused by, for example, mispointing or bending of the primary reflector. In some embodiments, the cells are set back from the image formed by the ball lens, and part of the light is reflected onto each cell small secondary reflectors in the form of mirrors set around its perimeter.

14 SOLAR ENERGY↗

Application of the OPTEX method for computing reflector parameters

We are investigating the OPTEX reflector model for obtaining few-group reflector parameters consistent with a reference power distribution in the core. In our study, the reference power distribution is obtained using a 142,872-region calculation defined over a 2D eighth-of-core pressurized water reactor and performed with the method of characteristics. The OPTEX method is based on generalized perturbation theory and uses an optimization algorithm known as parametric linear complementarity pivoting. The proposed model leads to few-group diffusion coefficients or P1-weighted macroscopic total cross sections that can be used to represent the reflector in full-core calculations. These few-group parameters can be spatially heterogeneous in order to correctly represent steel baffles present in modern pressurized water reactors. The optimal reflector parameters are compared to those obtained with a flux-volume weighting of the reflector cross sections recovered from the reference calculation. Important improvements in full-core power distribution are observed when the optimal parameters are used. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Presentation of the MERC work-flow for the computation of a 2D radial reflector in a PWR

This paper presents a work-flow for computing an equivalent 2D radial reflector in a pressurized water reactor (PWR) core, in adequacy with a reference power distribution, computed with the method of characteristics (MOC) of the lattice code APOLLO2. The Multi-modelling Equivalent Reflector Computation (MERC) work-flow is a coherent association of the lattice code APOLLO2 and the core code COCAGNE, structured around the ADAO (Assimilation de Donnees et Aide a l'Optimisation) module of the SALOME platform, based on the data assimilation theory. This study leads to the computation of equivalent few-groups reflectors, that can be spatially heterogeneous, which have been compared to those obtained with the OPTEX similar methodology developed with the core code DONJON, as a first validation step. Subsequently, the MERC work-flow is used to compute the most accurate reflector in consistency with all the R and D choices made at Electricite de France (EDF) for the core modelling, in terms of number of energy groups and simplified transport solvers. We observe important reductions of the power discrepancies distribution over the core when using equivalent reflectors obtained with the MERC work-flow. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Minimum critical masses and their uncertainties for several fissile nuclides and reflectors - 14296

A systematic effort was undertaken to reevaluate the minimum critical mass for several fissile nuclides and reflectors. This was done using MCNP6 in combination with several modern nuclear data libraries, viz. ENDF/B-VII.1, JENDL-4.0 and JEFF-3.1.1. This combination was benchmarked extensively against criticality safety benchmarks. The procedure to extract the minimum critical mass from the MCNP6 calculations was carefully implemented, so that it would have a negligible impact on the accuracy of the end results. All parts of the calculation, i.e. nuclear data processing, MCNP6 models, and post-processing, were applied consistently for all cases, involving varying fissile nuclides and reflectors. Results for the minimum critical mass were generated for {sup 233,235}U, {sup 236,239,241}Pu, {sup 242m}Am, {sup 243,245,247}Cm, and {sup 249,251}Cf, for the case of water moderation and water reflection. For {sup 235}U, the minimum critical mass was also calculated for cases with other reflectors, such as beryllium, heavy water, graphite, lead, and concrete. The results for the water reflection cases are in good agreement with most of the literature values, but for the cases with reflectors such as graphite, lead, or concrete, there are sizable differences. The accuracy of the results was assessed in two ways. First, a comparison was made with criticality safety benchmark results, by selecting benchmarks that resemble the minimum mass systems the most. It was clear that for {sup 233,235}U and {sup 239}Pu with water reflection, the differences in minimum critical masses between the libraries are consistent with the differences obtained for benchmark cases. The difference between the benchmark calculations and the benchmark values is then an indication of the accuracy with which one can simulate comparable systems. Secondly, sensitivity runs were performed with the new MCNP6 sensitivity option, based on ENDF/B-VII.1 nuclear data. For each fissile nuclide, the sensitivity of k{sub eff} to cross sections such as capture, fission, elastic, inelastic was calculated for the minimum critical mass case. The same was done for the {sup 1}H and {sup 16}O cross sections in the moderator and reflector. The uncertainty in k{sub eff} was calculated by combining the sensitivity profiles with the appropriate ENDF/B-VII.1 covariance matrix, using the SUSD code. As a final step, the uncertainty in k{sub eff} can be translated to an uncertainty in the minimum critical mass. (author)

42 ENGINEERING↗

Improved performance of a near-field thermophotovoltaic device by a back gapped reflector

Various spectral control techniques can be applied to improve the performance of a thermophotovoltaic (TPV) device. For example, a back surface reflector (BSR) is a common structure to improve the performance of TPV devices. A conventional metal BSR structure enhances the photogeneration rate by increasing the absorption probability of photons via back surface reflections, affording a second chance for absorption. However, the effects of surface passivation and external luminescence introduced by BSR structures have been previously ignored, which potentially decreases the performance of TPV devices. Recently, a back gapped reflector (BGR) structure was proposed to greatly improve the performance of far-field TPV devices by reducing imperfect reflections at the semiconductor-metal interface. In the present work, the performance improvement on a thin-film, near-field InAs TPV device with a BGR is investigated, comparing its performance to that with a conventional metal BSR. Surface passivation conditions are also investigated to further improve the performance of TPV devices with back reflectors. Further, the output power and efficiency are calculated using an iterative model combining fluctuational electrodynamics and the full drift diffusion model. For the well-passivated condition, when the BSR is replaced by the BGR, the calculated conversion efficiency of the near-field TPV was improved from 16.4% to 21% and the output power was increased by 10%. Finally, the absorption of the back reflectors and external luminescence loss are analyzed to explain the performance improvement.

external luminescence↗

UV–Visible reflectance of common light reflectors and their degradation after an ionization dose up to 100 Mrad

We report light reflectors are widely used to enhance scintillation light collection. Their enhancement level depends on the reflector’s reflectance at the scintillator’s emission wavelength. We report UV–Visible reflectance spectra, relative to BaSO 4 , for several common reflectors. Also reported is their radiation hardness against an ionization dose up to 100 Mrad. The results of this investigation provide a reference for applications of these reflectors in a severe radiation environment.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Systematic analysis of diffuse rear reflectors for enhanced light trapping in silicon solar cells

Simple diffuse rear reflectors can enhance the light path length of weakly absorbed near infrared light in silicon solar cells and set a benchmark for more complex and expensive light trapping structures like dielectric gratings or plasmonic particles. We analyzed such simple diffuse rear reflectors systematically by optical and electrical measurements. We applied white paint, TiO 2 nanoparticles, white backsheets and a silver mirror to bifacial silicon solar cells and measured the enhancement of the external quantum efficiency for three different solar cell geometries: planar front and rear side, textured front and planar rear side, and textured front and rear side. We showed that an air-gap between the solar cell and the reflector decreases the absorption enhancement significantly, thus white paint and TiO 2 nanoparticles directly applied to the rear cell surface lead to the highest short circuit current density enhancements. Here, the short circuit current density gains for a 200 um thick planar solar cell reached up to 1.8 mA/cm 2 , compared to a non-reflecting black rear side and up to 0.8 mA/cm 2 compared to a high-quality silver mirror rear side. For solar cells with textured front side the short circuit current density gains are in the range between 0.5 and 1.0 mA/cm 2 compared to a non-reflecting black rear side and do not significantly depend on the angular characteristic of the rear side reflector but mainly on its absolute reflectance.

14 SOLAR ENERGY↗

Back-surface recombination, electron reflectors, and paths to 28% efficiency for thin-film photovoltaics: A CdTe case study

As thin-film and silicon solar technologies mature, questions emerge about the upper bounds of thin-film solar performance and realistic experimental paths to reach them. Directions include increasing absorber hole density and bulk lifetime, improving the junction interface, reducing back-surface recombination, and implementing a back-surface electron reflector. Textbook solutions of idealized p-n junctions create a powerful conceptualization of solar cells as predominantly minority-carrier-driven devices. We demonstrate that thin films are distinct, and models often fail to capture the important role of majority-carrier lifetime, leading to contradictions with lifetime measurements and overestimates of potential device improvement from back-surface passivation and/or reflectors. Furthermore, we identify methods to probe majority-carrier lifetime and re-examine the degree to which back-surface passivation and electron reflectors can increase efficiency for a range of common thin-film interface and absorber properties, using current and emerging CdTe technology as an example. Here, the results indicate that a practical approach is to focus first on improving front-interface recombination velocity and the absorber properties, and then on implementing the back-surface passivation or reflector, which can ultimately allow thin-film solar technology to reach 28% efficiency.

14 SOLAR ENERGY↗

Signal Whisperers: Enhancing Wireless Reception Using DRL-Guided Reflector Arrays

This paper presents a multi-agent reinforcement learning (MARL) approach for controlling adjustable metallic reflector arrays to enhance wireless signal reception in non-line-of-sight (NLOS) scenarios. Unlike conventional reconfigurable intelligent surfaces (RIS) that require complex channel estimation, our system employs a centralized training with decentralized execution (CTDE) paradigm where individual agents corresponding to reflector segments autonomously optimize reflector element orientation in three-dimensional space using spatial intelligence based on user location information. Through extensive ray-tracing simulations with dynamic user mobility, the proposed multi-agent beam-focusing framework demonstrates substantial performance improvements over single-agent reinforcement learning baselines, while maintaining rapid adaptation to user movement within one simulation step. Comprehensive evaluation across varying user densities and reflector configurations validates system scalability and robustness. The results demonstrate the potential of learning-based approaches for adaptive wireless propagation control.

deep reinforcement learning↗

Wirelessly Controllable Inflated Electroactive Polymer (EAP) Reflectors

Inflatable membrane reflectors are attractive for deployable, large aperture, lightweight optical and microwave systems in micro-gravity space environment. However, any fabrication flaw or temperature variation may results in significant aberration of the surface. Even for a perfectly fabricated inflatable membrane mirror with uniform thickness, theory shows it will form a Hencky curve surface but a desired parabolic or spherical surface. Precision control of the surfaceshape of extremely flexible membrane structures is a critical challenge for the success of this technology. Wirelessly controllable inflated reflectors made of electroactive polymers (EAP) are proposed in this paper. A finite element model was configured to predict the behavior of the inflatable EAP membranes under pre-strains, pressures and distributed electric charges on the surface. To explore the controllability of the inflatable EAP reflectors, an iteration algorism was developed to find the required electric actuation for correcting the aberration of the Hencky curve to the desired parabolic curve. The correction capability of the reflectors with available EAP materials was explored numerically and is presented in this paper.

Electroactive polymer (EAP)↗

Segmented Hexagonal Antenna Reflector Concentrically Stacked Using Shape Memory Composite Tubular Hinges

A new architecture for solid surface reflector antennas scalable to sizes greater than 10 m is presented. The design combines the compact, lightness and simplicity characteristics of advanced deployable structures to create sub-reflectors that can be assembled in space into larger units using a robotic arm and operations under development by a related parallel project. The seven-panel hexagonal sub-reflector is divided into hexagonal panels of that efficiently stack concentrically and vertically. The central panel is connected to each side panel on the back side by a pair of tubular shape memory composite hinges that enable the required deployment kinematics. A secondary mechanism ultimately closes the interpanel gap. The focus of the paper is on the development of the sub-reflector elements, namely the tubular hinges that use embedded heaters and sensors for actuation, the actuation mechanisms, and the lightweight sandwich construction panels. A finite element analysis parametric study assessed how design features of the hinge affect its stowage and deployment dynamics. The component fabrication and testing plans for the two-panel assembly breadboard model are outlined.

deployable reflectors↗

Segmented Hexagonal Antenna Reflector Concentrically Stacked Using Shape Memory Composite Tubular Hinges

A new architecture for solid surface reflector antennas scalable to sizes greater than 10 m is presented. The design combines the compact, lightness and simplicity characteristics of advanced deployable structures to create sub-reflectors that can be assembled in space into larger units using a robotic arm and operations under development by a related parallel project. The seven-panel hexagonal sub-reflector is divided into hexagonal panels of that efficiently stack concentrically and vertically. The central panel is connected to each side panel on the back side by a pair of tubular shape memory composite hinges that enable the required deployment kinematics. A secondary mechanism ultimately closes the interpanel gap. The focus of the paper is on the development of the sub-reflector elements, namely the tubular hinges that use embedded heaters and sensors for actuation, the actuation mechanisms, and the lightweight sandwich construction panels. A finite element analysis parametric study assessed how design features of the hinge affect its stowage and deployment dynamics. The component fabrication and testing plans for the two-panel assembly breadboard model are outlined.

deployable reflectors↗