Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RAM analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Laboratory degradation of Kapton in a low energy oxygen ion beam

An atomic oxygen ion beam, accelerated from a tunable microwave resonant cavity, was used at Lewis Research Center to bombard samples of the widely used polyimide Kapton. The Kapton experienced degradation and mass loss at high rates, which may be comparable to those found in Space Shuttle operations if the activation energy supplied by the beam enabled surface reactions with the ambient oxygen. The simulation reproduced the directionality (ram-wake dependence) of the degradiation, the change in optical properties of the degraded materials, and the structure seen in scanning electron micrographs of samples returned on the Shuttle Trails with a substituted argon ion beam produced no rapid degradation. Energy Dispersive X-ray Analysis (EDAX) showed significant surface composition changes in all bombarded samples. Mass loss rates and surface composition changes are discussed in terms of the possible oxidation chemistry of the interaction. Finally, the question of how the harmful degradation of materials in low earth orbit can be minimized is addressed.

Ferguson, D. C.↗
NASA NTRS1987

Measurement uncertainty for the Uniform Engine Testing Program conducted at NASA Lewis Research Center

An uncertainty analysis was conducted to determine the bias and precision errors and total uncertainty of measured turbojet engine performance parameters. The engine tests were conducted as part of the Uniform Engine Test Program which was sponsored by the Advisory Group for Aerospace Research and Development (AGARD). With the same engines, support hardware, and instrumentation, performance parameters were measured twice, once during tests conducted in test cell number 3 and again during tests conducted in test cell number 4 of the NASA Lewis Propulsion Systems Laboratory. The analysis covers 15 engine parameters, including engine inlet airflow, engine net thrust, and engine specific fuel consumption measured at high rotor speed of 8875 rpm. Measurements were taken at three flight conditions defined by the following engine inlet pressure, engine inlet total temperature, and engine ram ratio: (1) 82.7 kPa, 288 K, 1.0, (2) 82.7 kPa, 288 K, 1.3, and (3) 20.7 kPa, 288 K, 1.3. In terms of bias, precision, and uncertainty magnitudes, there were no differences between most measurements made in test cells number 3 and 4. The magnitude of the errors increased for both test cells as engine pressure level decreased. Also, the level of the bias error was two to three times larger than that of the precision error.

Abdelwahab, Mahmood↗
NASA NTRS1992

Spectral characteristics of Shuttle glow

The glowing cloud near the ram surfaces of the Space Shuttle was observed with a hand-held, intensified spectrograph operated by the astronauts from the aft-flight-deck of the Space Shuttle. The spectral measurements were made between 400 and 800 nm with a resolution of 3 nm. Analysis of the spectral response of the instrument and the transmission of the Shuttle window was performed on orbit using earth-airglow OH Meinel bands. This analysis resulted in a correction of the Shuttle glow intensity in the spectral region between 700 and 800 nm. The data presented in this report is in better agreement with laboratory measurements of the NO2 continuum.

Viereck, R. A.↗
NASA NTRS1994

Excitation of the low lying vibrational levels of H2O by O(3P) as measured on Spacelab 2

The data from the infrared telescope (IRT), which was flown on space shuttle Challenger Spacelab 2 mission (July 1985), were originally reported by Koch et al. (1987) as originating from near orbital emissions, primarily H2O. In this study, analysis of this data was extended to determine the collisional cross sections for the excitation of the low lying vibrational levels of H2O, present in the orbiter cloud, by atmospheric O(3P). The evaluation of the contribution to the measured signal from solar excitation and ram O excitation of outgassing H2O permits the determination of the H2O column density and the excitation cross section of the (101) level at an O(3P) velocity of approximately 7.75 km/s. Contributions to the radiation in the 1.7-3.0 micron band by transitions from the (100), (001), and multiquantum excited levels are discussed. The findings of the study are (1) the IRT data for the 4.5-9.5 micron and the nighttime data for the 1.7-3.0 micron sensors are consistent with being explained by collision excitation of H2O by O(3P), (2) diurnal variations of 4.5-9.5 micron intensities follow the model predicted O density for a full orbit, (3) daytime increases in the H2O cloud density were not evident, (4) the cross sections for the collisional excitation process are derived and compared to values computated by Johnson (1986) and Redmon et al. (1986), (5) theoretical investigation suggests greater than 60% of the radiation from H2O is a result of multiphoton emission resulting from collisional multiquanta excitation, and (6) the large daytime increase in the 1.7-3.0 micron intensity data suggests that O(+) may likely be instrumental in producing excited H2O(+) through charge exchange.

Meyerott, R. E.↗
NASA NTRS2010

Modeling of the Magnetosphere of Mercury at the Time of the First MESSENGER Flyby

The MESSENGER spacecraft flyby of Mercury on 14 January 2008 provided a new opportunity to study the intrinsic magnetic field of the innermost planet and its interaction with the solar wind, The model presented in this paper is based on the solution of the three-dimensional, bi-f1uid equations for solar wind protons and electrons in the absence of mass loading, In this study we provide new estimates of Mercury's intrinsic magnetic field and the solar wind conditions that prevailed at the time of the flyby. We show that the location of the boundary layers and the strength of the magnetic field along the spacecraft trajectory can be reproduced with a solar wind ram pressure P(sub sw) = 6.8 nPa and a planetary magnetic dipole having a magnitude of 210 R(sub M)(exp 3)- nT and an offset of 0.18 R(sub M) to the north of the equator, where R(sub M) is Mercury's radius. Analysis of the plasma flow reveals the existence of a stable drift belt around the planet; such a belt can account for the locations of diamagnetic decreases observed by the MESSENGER Magnetometer. Moreover, we determine that the ion impact rate at the n011hern cusp was four times higher than at the southern cusp, a result that provides a possible explanation for the observed north-south asymmetry in exospheric sodium in the neutral tail.

Benna, Mehdi↗
NASA NTRS1983

The Development of a Digital Processing System for Accurate Range Determinations

The development of an accurate close range (from 0.0 meters to 30.0 meters) radar system for Teleoperator Maneuvering Systems (TMS) is discussed. The system under investigation is a digital processor that converts incoming signals from the radar system into their related frequency spectra. Identification will be attempted by correlating spectral characteristics with accurate range determinataions. The system will utilize an analog to digital converter for sampling and converting the signal from the radar system into 16-bit digital words (two bytes) for RAM storage, data manipulations, and computations. To remove unwanted frequency components the data will be retrieved from RAM and digitally filtered using large scale integration (LSI) circuits. Filtering will be performed by a biquadratic routine within the chip which carries out the required filter algorithm. For conversion to a frequency spectrum the filtered data will be processed by a Fast Fourier Transform chip. Analysis and identification of spectral characteristics for accurate range determinations will be made by microcomputer computations.

Pujol, A., Jr.↗
NASA NTRS1986

Takeoff predictions for powered-lift aircraft

Takeoff predictions for powered lift short takeoff (STO) aircraft have been added to NASA Ames Research Center's aircraft synthesis (ACSYNT) code. The new computer code predicts the aircraft engine and nozzle settings required to achieve the minimum takeoff roll. As a test case, it predicted takeoff around rolls and nozzle settings for the YAV-8B Harrier that were close to the actual values. Analysis of takeoff performance for an ejector-augmentor design and a vectoring-nozzle design indicated that ground roll can be decreased, for either configuration, by horizontally moving the rear thrust vector closer to the center of gravity, by increasing the vertical position of the ram drag-vector, or by moving the rear thrust vector farther below the center of gravity.

Wardwell, Douglas A.↗
NASA NTRS2003

[Results for SHEBA/FIRE]

The Atmospheric Research Laboratory's Radiation Measurement System (RAMS) was on the NCAR C-130 aircraft in May and July 1998, collecting radiometric data on the science flights conducted in the vicinity of the Surface Heat Budget of the Arctic Ocean (SHEBA) ship. These measurements were part of the FIRE Arctic Cloud Experiment (FIRE ACE). Analysis of some of the data focused on the absorption, reflection, and transmittance of Arctic clouds, especially compared to model results. In order to assess the absorption of solar radiation by the clear and cloudy atmosphere in the Arctic the measurements from the radiometers were combined in pairs of above-cloud segments and below-cloud segments. To get these pairs, the data for all sixteen of the flights (8 in May and 8 in July) were examined for occurrences of low-altitude segments in proximity to high-altitude segments. The low-altitude data are then treated as measurements of the bottom of a layer and the high-altitude data are taken as measurements of the top of the layer. With measurements of the upwelling and downwelling irradiances above and below a layer one can determine the reflectance, transmittance, and absorptance of the layer. Attachment: Doelling, D.R., P. Minnis, D.A. Spangenberg, V. Chakrapani, A. Mahesh, S.K. Pope, and F.P.J. Valero, Cloud radiative forcing at the top of the atmosphere during FIRE ACE derived from AVHRR data, J. Geophys. Res. 106, 15,279-15,296,2001. Minnis, P., D.R. Doelling, D.A. Spangenberg, A. Mahesh, S.K. Pope, and F.P.J. Valero, AVHRR-derived cloud radiative forcing over the ARM NSA and SHEBA site during FIRE ACE, abstract submitted to the ARM Science Team Meeting, San Antonio, TX, M a . 13-17,2000. Pope, S.K., and F.P.J. Valero, Measured and modeled radiometric fluxes in the Arctic during FIRE-ACE, presented as a poster at the American Geophysical Union meeting, San Francisco, CA, Dec. 13-17, 1999. Pope, S.K., and F.P.J. Valero, Measured and modeled radiometric fluxes in the Arctic during FIRE-ACEy paper presented at SHEBA/FIRE Workshop, National Center for Atmospheric Research, Boulder, Colo., Apr. 17-20,2000.

Valero, Francisco P. J.↗
NASA NTRS2015

SRAG Measurements Performed During the Orion EFT-1 Mission

The Exploration Flight Test 1 (EFT-1) was the first flight of the Orion Multi-Purpose Crew Vehicle (MPCV). The flight was launched on December 5, 2014, by a Delta IV Heavy rocket and lasted 4.5 hours. The EFT-1 trajectory involved one low altitude orbit and one high altitude orbit with an apogee of almost 6000 km. As a result of this particular flight profile, the Orion MPCV passed through intense regions of trapped protons and electron belts. In support of the radiation measurements aboard the EFT-1, the Space Radiation Analysis Group (SRAG) provided a Battery-operated Independent Radiation Detector (BIRD) based on Timepix radiation monitoring technology similar to that employed by the ISS Radiation Environmental Monitors (REM). In addition, SRAG provided a suite of optically and thermally stimulated luminescence detectors, with 2 Radiation Area Monitor (RAM) units collocated with the BIRD instrument for comparison purposes, and 6 RAM units distributed at different shielding configurations within the Orion MPCV. A summary of the EFT-1 Radiation Area Monitors (RAM) mission dose results obtained from measurements performed in the Space Radiation Dosimetry Laboratory at the NASA Johnson Space Center will be presented. Each RAM included LiF:Mg,Ti (TLD-100), (6)LiF:Mg,Ti (TLD-600), (7)LiF:Mg,Ti (TLD-700), Al2O3:C (Luxel trademark), and CaF2:Tm (TLD-300). The RAM mission dose values will be compared with the BIRD instrument total mission dose. In addition, a similar comparison will be shown for the ISS environment by comparing the ISS RAM data with data from the six Timepix-based REM units deployed on ISS as part of the NASA REM Technology Demonstration.

Gaza, Ramona↗
NASA NTRS1989

Effects of cosmic rays on single event upsets

Assistance was provided to the Brookhaven Single Event Upset (SEU) Test Facility. Computer codes were developed for fragmentation and secondary radiation affecting Very Large Scale Integration (VLSI) in space. A computer controlled CV (HP4192) test was developed for Terman analysis. Also developed were high speed parametric tests which are independent of operator judgment and a charge pumping technique for measurement of D(sub it) (E). The X-ray secondary effects, and parametric degradation as a function of dose rate were simulated. The SPICE simulation of static RAMs with various resistor filters was tested.

Venable, D. D.↗
NASA NTRS1948

Altitude-wind-tunnel investigation of a 4000-pound-thrust axial-flow turbojet engine VI : combustion-chamber performance

An analysis of the performance of the types A, B, and C combustion chambers of the 4000-pound-thrust axial-flow turbojet engine is presented. The data were obtained from investigations of the complete engine over a range of pressure altitudes from 5000 to 40,000 feet and ram pressure ratios from 1.00 to 1.86. The combustion-chamber pressure losses, the effect of the losses on cycle efficiency, and the combustion efficiency are discussed.

Pinkel, I Irving↗
NASA NTRSDate not supplied

Artemis 1 Radiation Modeling and Analysis Using Operational Methods

The successful completion of the Artemis 1 mission has provided NASA with a significant volume of space radiation dosimetry data that can be used to verify the accuracy of current operational SRAG dose computation models and methods for Beyond LEO missions. High-Fidelity CAD models of the Artemis 1 MPCV Orion were raytraced in 10,000 directions per sensor location, including the location of Artemis HERA sensors, Artemis RAMs (TLDs), and the crew active dosimetry (CADs). The full Artemis 1 mission was modelled using the as-flown trajectory, Ap9-Ae9 IRENE providing the VAB trapped proton and electron environment, and the Badhwar-O’Neill 2020 model providing the freespace GCR environment. IGRF 12 was used to compute cutoff rigidities for the GCR environment in LEO. 1DHZETRN was used to estimate point doses at each sensor position. Computed RAM doses were within 5% of measured values. The computed VAB transit and freespace GCR dose rates showed good qualitative agreement with measured HERA values. An estimate of normalized mean effective dose for a hypothetical male crew member on Artemis 1 using current standard operational methods was computed to be 22.3 mSv.

Artemis 1↗
NASA NTRS1983

Digital Instrumentation Analysis and Navigation System (DIANS) for system identification

Hardware, software, and performance features of the Digital Instrumentation and Navigation System (DIANS) designed for NASA research to collect flight data as a strap-down system are detailed. The support software for the system has a cross compiler, a linkage editor, and cross assembler, extended communication capabilities, postflight processing applications, and compilers for PASCAL, FORTRAN, CBASIC and MT. The DIANS microcomputer has a 1 Mbyte RAM module, a fast floating point processor board, a 68000 monoboard computer with 64 RAM, a 128 Kbyte bubble memory card, and a navigation radio. The system also carries a battery for full system operation for over an hour. The support software is also stored on a host mainframe computer, which has a CP/M operating system. Pitch, roll, and heading data are gathered from the on-board system, and communication is possible between the airborne and ground-based computer.

Smyth, R. K.↗
NASA NTRS1987

Temperature characteristics of silicon space solar cells and underlying parameters

Silicon space cells, 2 cm x 2 cm, with 10 ohm-cm p-base resistivity, 8-mil base thickness, and no back-surface fields have been investigated over the temperature range from 301 to 223 K by measurements of dark forward and reverse current-voltage characteristics and current-voltage relations under illumination. From dark forward bias data, the first and second diode saturation currents, I01 and I02, are determined and hence the base diffusion length and lifetime of minority carriers as functions of temperature. Lifetime increases exponentially with temperature and is explained by a Shockley-Read-Hall model with deep recombination levels 0.245 eV above the valence band. The I02 variation with temperature follows the Sah-Noyce-Shockley-Choo model except at low temperature where extra transitions raise the value above the predicted level. Reverse bias current at low voltage is a thermally assisted tunneling process via deep levels which are observed in base recombination at higher temperatures. The tunneling effects tend to become independent of temperature in the low-temperature region. These results demonstrate the ability to deduce basic parameters such as lifetime from simple measurements and show that back-surface fields offer no advantage at temperatures below 230 K. The analysis also explains the fall in lifetimes observed as the base conductivity increases, attributing it to native defects (perhaps carbon-oxygen-vacancy complexes) rather than the concentration of base dopant.

Anspaugh, B. E.↗
NASA NTRS1953

Analysis of several methods of pumping cooling air for turbojet engine afterburners

Several methods of pumping air to an annular cooling passage surrounding a typical axial-flow turbojet-engine afterburner were evaluated and compared on the basis of thrust and specific fuel consumption of the systems. Each system was analyzed over a range of afterburner-wall temperatures, flight Mach numbers, and exhaust-gas temperatures at sea level and 35,000 feet. Ram pressure recovery, boundary-layer pressure recovery, and the engine-jet actuated ejector appear to be satisfactory systems at high Mach numbers. Cooling with compressor-exit air bleed was found to be unsatisfactory,but the use of compressor-exit bleed air as the primary fluid in a high-performance ejector was satisfactory. The use of an auxiliary compressor driven from the engine shaft increased the thrust and decreased the specific fuel consumption of the engine for many of the conditions investigated.

PUMPS, JET AND THRUST AUGMENTORS↗
NASA NTRS1993

Finite element/finite volume approaches with adaptive time stepping strategies for transient thermal problems

An adaptive time stepping strategy for transient thermal analysis of engineering systems is described which computes the time step based on the local truncation error with a good global error control and obtains optimal time steps to be used during the analysis. Combined mesh partitionings involving FEM/FVM meshes based on physical situations to obtain numerically improved physical representations are also proposed. Numerical test cases are described and comparative pros and cons are identified for practical situations.

Mohan, Ram V.↗
NASA NTRS1992

Thermal Control Surfaces Experiment (TCSE) materials analysis

Materials on the Thermal Control Surfaces Experiment (TCSE) underwent changes in their properties during the 5.8 years of exposure to the combined space environment. The analysis of these materials is continuing and current results are discussed. Some materials were significantly degraded such as silver Teflon, S13GLO, and Z302; while others such as Z93 and YB71 were stable. Time dependent flight data is provided, along with preflight and postflight measurements. Results are compared with other experiments, demonstrating the atomic oxygen (AO) ram effect. Atomic oxygen texturing of silver Teflon varies with incident angle. Even indirect exposure to atomic oxygen appears to be involved with surface texturing on the interior of the TCSE. Localized contamination occurred at discrete locations both inside and on exterior surfaces. Most of the visible deposits were the result of the classical photo-enhanced contamination deposition. The synergism of combined space environmental effects is demonstrated by the specific localization of contamination caused by photo-enhanced deposition versus AO removal. Optical degradation measurements of these contaminated areas, utilizing a new portable reflectometer, are presented.

Wilkes, Donald R.↗
NASA NTRS1993

Mesoscale simulations of the November 25-26 and December 5-6 cirrus cases using the RAMS model

The Regional Atmospheric Modeling System (RAMS), developed at Colorado State University, was used during the First ISCCP (International Satellite Cloud Climatology Project) Regional Experiment (FIRE) 2 (13 Nov. through 6 Dec. 1991) to provide real time forecasts of cirrus clouds. Forecasts were run once a day, initializing with the 0000 UTC dataset provided by NOAA (Forecast Systems Laboratory (FSL) Mesoscale Analysis and Prediction System (MAPS)). In order to obtain better agreement with observations, a second set of simulations were done for the FIRE 2 cases that occurred on 25-26 Nov. and 5-6 Dec. In this set of simulations, a more complex radiation scheme was used, the Chen/Cotton radiation scheme, along with the nucleation of ice occurring at ice supersaturations as opposed to nucleation occurring at water supersaturations that was done in the actual forecast version. The runs using these more complex schemes took longer wall clock time (7-9 hours for the actual forecasts as compared to 12-14 hrs for the runs using the more complex schemes) however, the final results of the simulations were definitely improved upon. Comparisons between these two sets of simulations are given. Now underway are simulations of these cases using a closed analytical solution for the auto-conversion of ice from a pristine ice class (sizes less than about 50 microns in effective diameter) to a snow class (effective diameters on the order of several hundred microns). This solution is employed along with a new scheme for the nucleation of ice crystals due to Meyers et al and Demott et al. The scheme is derived assuming complete gamma distributions for both the pristine and snow classes. The time rate of change of the number concentration and mass mixing-ratio of each distribution is found by calculating either the flux of crystals that grow beyond a certain critical diameter by vapor deposition in an ice supersaturated regime or by calculating the flux of crystals that evaporate to sizes below that same critical effective diameter.

Harrington, J. L.↗