Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Propeller noise”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

The Dornier 328 Acoustic Test Cell (ATC) for interior noise tests and selected test results

To perform acoustic studies for achieving low noise levels for the Dornier 328, an acoustic test cell (ATC) of the Dornier 328 has been built. The ATC consists of a fuselage section, a realistic fuselage suspension system, and three exterior noise simulation rings. A complex digital 60 channel computer/amplifier noise generation system as well as multichannel digital data acquisition and evaluation system have been used. The noise control tests started with vibration measurements for supporting acoustic data interpretation. In addition, experiments have been carried out on dynamic vibration absorbers, the most important passive noise reduction measure for low frequency propeller noise. The design and arrangement of the current ATC are presented. Furthermore, exterior noise simulation as well as data acquisition are explained. The most promising results show noise reduction due to synchrophasing and dynamic vibration absorbers.

Hackstein, H. Josef↗
NASA NTRS1987

Advanced turboprop noise prediction based on recent theoretical results

The development of a high speed propeller noise prediction code at Langley Research Center is described. The code utilizes two recent acoustic formulations in the time domain for subsonic and supersonic sources. The structure and capabilities of the code are discussed. Grid size study for accuracy and speed of execution on a computer is also presented. The code is tested against an earlier Langley code. Considerable increase in accuracy and speed of execution are observed. Some examples of noise prediction of a high speed propeller for which acoustic test data are available are given. A brisk derivation of formulations used is given in an appendix.

Farassat, F.↗
NASA NTRS1992

Building vibrations induced by noise from rotorcraft and propeller aircraft flyovers

Noise and building vibrations were measured for a series of helicopter and propeller-driven aircraft flyovers at WFF during May 1978. The building response data are compared with similar data acquired earlier at sites near Dulles and Kennedy Airports for operation of commercial jet transports, including the Concorde supersonic transport. Results show that noise-induced vibration levels in windows and walls are directly proportional to sound pressure level and that for a given noise level, the acceleration levels induced by a helicopter or a propeller-driven aircraft flyover cannot be distinguished from the acceleration levels induced by a commercial jet transport flyover. Noise-induced building acceleration levels were found to be lower than those levels which might be expected to cause structural damage and were also lower than some acceleration levels induced by such common domestic events as closing windows and doors.

Shepherd, Kevin P.↗
NASA NTRS1989

A review and update of the NASA aircraft noise prediction program propeller analysis system

The National Aeronautics and Space Administration (NASA) Aircraft Noise Prediction Program (ANOPP) Propeller Analysis System (PAS) is a set of computational modules for predicting the aerodynamics, performance, and noise of propellers. The ANOPP PAS has the capability to predict noise levels for propeller aircraft certification and produce parametric scaling laws for the adjustment of measured data to reference conditions. A technical overview of the prediction techniques incorporated into the system is presented. The prediction system has been applied to predict the noise signature of a variety of propeller configurations including the effects of propeller angle of attack. A summary of these validation studies is discussed with emphasis being placed on the wind tunnel and flight test programs sponsored by the Federal Aviation Administration (FAA) for the Piper Cherokee Lance aircraft. A number of modifications and improvements have been made to the system and both DEC VAX and IBM-PC versions of the system have been added to the original CDC NOS version.

Golub, Robert A.↗
NASA NTRS1982

Farfield inflight measurement of high-speed turboprop noise

A flight program was carried out to determine the variation of noise level with distance from a model high speed propeller. Noise measurements were obtained at different distances from a SR-3 propeller mounted on a JetStar aircraft, with the test instrumentation mounted on a Lear jet flown in formation. The propeller was operated at 0.8 flight Mach number, 1.12 helical tip Mach number and at 0.7 flight Mach number, 1.0 helical tip Mach number. The instantaneous pressure from individual blades was observed to rise faster at the 0.8 M flight speed, than at the 0.7 M flight speed. The measured levels appeared to decrease in good agreement with a 6 dB/doubling of distance decay, over the measurement range of approximately 16 m to 100 m distance. Further extrapolation, to the distances represented by a community, would suggest that the propagated levels during cruise would not cause a serious community annoyance.

Balombin, J. R.↗
NASA NTRS1980

Noise transmission and control for a light, twin-engine aircraft

One of the dominant source-path combinations for cabin noise in light, twin-engine aircraft is propeller noise being transmitted through the fuselage sidewall. This source-path was investigated and candidate sidewall add-on treatment were installed and tested using both an external sound source and the propeller in a ground static runup. Results indicate that adding either mass or stiffness to the fuselage skin would improve sidewall attenuation and that the honeycomb stiffness treatment used generally provided more improvement than an equal amount of added mass. It is proposed that double-wall construction in conjunction with skin stiffening should provide a good weight efficient combination for the aircraft studied.

Barton, C. K.↗
NASA NTRS1992

Vibro-Acoustic FE Analyses of the Saab 2000 Aircraft

A finite element model of the Saab 2000 fuselage structure and interior cavity has been created in order to compute the noise level in the passenger cabin due to propeller noise. Areas covered in viewgraph format include the following: coupled acoustic/structural noise; data base creation; frequency response analysis; model validation; and planned analyses.

Green, Inge S.↗
NASA NTRS1986

Cruise noise of counterrotation propeller at angle of attack in wind tunnel

The noise of a counterrotation propeller at angle of attack was measured in the NASA Lewis 8- by 6-Foot Supersonic Wind Tunnel at cruise conditions. Noise increases of as much as 4 dB were measured at positive angles of attack on the tunnel side wall, which represented an airplane fuselage. These noise increases could be minimized or eliminated by operating the counterrotation propeller with the front propeller turning up-inboard. This would require oppositely rotating propellers on opposite sides of the airplane. Noise analyses at different bandwidths enabled the separate front- and rear-propeller tones, as well as the total noise, at each harmonic to be determined. A simplified noise model was explored to show how the observed circumferential noise patterns of the separate propeller tones might have occurred. The total noise pattern, which represented the sum of the front- and rear-propeller tones at a particular harmonic, showed trends that would be hard to interpret without the separate-tone results. Therefore it is important that counterrotation angle-of-attack noise data be taken in such a manner that the front- and rear-propeller tones can be separated.

Dittmar, J. H.↗
NASA NTRS1983

Farfield inflight measurements of high-speed turboprop noise

A flight program was carried out to determine the variation of noise level with distance from a model high-speed propeller. Noise measurements were obtained at different distances from a SR-3 propeller mounted on a JetStar aircraft, with the test instrumentation mounted on a Learjet flown in formation. The propeller was operated at 0.8 m flight Mach number, 1.12 helical tip Mach number and at 0.7 flight Mach number, 1.0 helical tip Mach number. The instantaneous pressure from individual blades was observed to rise faster at the 0.8 flight speed, than at the 0.7 M flight speed. The measured levels appeared to decrease in good agreement with a 6 dB/doubling of distance decay, over the measurement range of approximately 16 m to 100 m distance. Further extrapolation, to the distances represented by a community, would suggest that the propagated levels during cruise would not cause a serious community annoyance.

Balombin, J. R.↗
NASA NTRS1987

The effect of front-to-rear propeller spacing on the interaction noise of a model counterrotation propeller at cruise conditions

The effect of front-to-rear propeller spacing on the interaction noise of a counterrotation propeller model was measured at cruise conditions. The data taken at an axial Mach number of 0.80 behaved as expected: interaction noise was reduced with increased spacing. The data taken at M=0.76 and M=0.72 did not behave as expected. At some of the test conditions the noise was unchanged; others even showed noise increases with increased spacing. A possible explanation, involving the amount of downstream blade area impacted by the tip vortex, is presented.

Dittmar, James H.↗
NASA NTRS1987

Acoustic transmissibility of advanced turboprop aircraft windows

Advanced turboprop technology allows propeller aircraft to reach cruise speeds comparable to current jet aircraft yet with considerable fuel savings. Due to the higher blade loading and higher tip speed of these propellers, noise levels of up to 150 dB are expected on the outside of the fuselage in the propeller plane. In this study the transmissibility of triple pane windows, designed to provide 69 dB noise transmission loss at the blade propeller frequency of 164 Hz, was experimentally investigated using insertion loss and three-dimensional intensity techniques. A modal analysis on the outer window panes was conducted to determine pane modal frequencies. Coherence and phase relation of outer panes and window frame were established to obtain double/triple wall and lump mass resonance frequencies. Double/triple wall resonances were found to degrade the transmission loss of the two windows. It was shown that, at the blade passage frequency and the first two overtones, the combinations of window plus scratch shield provide less transmission loss than the average transmission loss of the treated fuselage. Strong disagreement was obtained between the experimental transmission loss of this investigation and the theoretical predictions from another study.

Grosveld, Ferdinand W.↗
NASA NTRS1980

An overview of NASA's propeller and rotor noise research

This paper presents a summary of NASA's propeller and rotor noise research. The objective of this research is to develop the technology and data base required to reduce propeller and rotor noise with minimum performance penalties. The status of current research will be described for both low- and high-speed propellers and for helicopter rotors. Recent results and future research thrusts are also discussed

Greene, G. C.↗
NASA NTRS1986

Advanced turboprop noise prediction: Development of a code at NASA Langley based on recent theoretical results

The development of a high speed propeller noise prediction code at Langley Research Center is described. The code utilizes two recent acoustic formulations in the time domain for subsonic and supersonic sources. The structure and capabilities of the code are discussed. Grid size study for accuracy and speed of execution on a computer is also presented. The code is tested against an earlier Langley code. Considerable increase in accuracy and speed of execution are observed. Some examples of noise prediction of a high speed propeller for which acoustic test data are available are given. A brisk derivation of formulations used is given in an appendix.

Farassat, F.↗
NASA NTRS1981

Noise transmission and attenuation for business aircraft

This paper describes analytical studies applicable for estimating the effects of noise transmission into light aircraft and commuter type aircraft. The propeller noise and turbulent boundary layer noise are considered. The analytical model described uses modal methods and incorporates flat stiffened panels for flat sided sidewalls and curved stiffened panels for cylindrical enclosures. The numerical results include noise attenuation with add-on treatments and the sensitivity of the transmitted noise to the discrete stiffening of the sidewall panels.

Vaicaitis, R.↗
NASA NTRS1984

Annoyance caused by propeller airplane flyover noise

Laboratory experiments were conducted to provide information on quantifying the annoyance response of people to propeller airplane noise. The items of interest were current noise metrics, tone corrections, duration corrections, critical band corrections, and the effects of engine type, operation type, maximum takeoff weight, blade passage frequency, and blade tip speed. In each experiment, 64 subjects judged the annoyance of recordings of propeller and jet airplane operations presented at d-weighted sound pressure levels of 70, 80, and 90 dB in a testing room which simulates the outdoor acoustic environment. The first experiment examined 11 propeller airplanes with maximum takeoff weights greater than or equal to 5700 kg. The second experiment examined 14 propeller airplanes weighting 5700 kg or less. Five jet airplanes were included in each experiment. For both the heavy and light propeller airplanes, perceived noise level and perceived level (Stevens Mark VII procedure) predicted annoyance better than other current noise metrics.

Mccurdy, D. A.↗
NASA NTRS1986

An experimental investigation of reducing advanced turboprop cabin noise by wing shielding

An experimental investigation was undertaken to determine if wing shielding could reduce the noise impacting the fuselage of an advanced turboprop airplane. Four wings were tested behind two eight-bladed propeller models. Significant shielding of the propeller noise was observed and a particular wing-propeller geometry was identified to provide the most shielding. Specifically, an up-inboard rotation would be needed for a low-wing airplane and a down-inboard rotation for a high-wing airplane. As the axial Mach number was increased, the position where the shielding starts moved farther downstream. This shift in the start of shielding was roughly a straight line with respect to Mach number between M = 0.7 and M = 0.8. At M = 0.85 the start of shielding does not shift any farther downstream. A simple barrier noise-reduction model gave the same trends with transducer positions as did the data, and, if corrected for Mach number shift, the model might be used to provide estimates of the wing shielding. Besides providing a barrier to the noise reaching the shielded area, the wing also reflects some of the noise back onto the unshielded area. This can make the noise difference between the unshielded and shielded areas of the fuselage larger than would be expected by simple wind shielding.

Dittmar, J. H.↗