Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Phase slips”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Orientation and temperature dependence of some mechanical properties of the single-crystal nickel-base superalloy Rene N4. 3: Tension-compression anisotropy

Single crystal superalloy specimens with various crystallographic directions along their axes were tested in compression at room temperature, 650, 760, 870, and 980 deg C. These results are compared with the tensile behavior studied previously. The alloy, Rene N4, was developed for gas turbine engine blades and has the nominal composition 3.7 Al, 4.2 Ti, 4 Ta, 0.5 Nb, 6 W, 1.5 Mo 9 Cr. 7.5 Co, balance Ni, in weight percent. Slip trace analysis showed that primary cube slip occurred even at room temperature for the 111 specimens. With increasing test temperature more orientations exhibited primary cube slip, until at 870 deg C only the 100 and 011 specimens exhibited normal octahedral slip. The yield strength for octahedral slip was numerically analysed using a model proposed by Lall, Chin, and Pope to explain deviations from Schmid's Law in the yielding behavior of a single phase Gamma prime alloy, Ni3(Al, Nb). The Schmid's Law deviations in Rene N4 were found to be largely due to a tension-compression anisotropy. A second effect, which increases trength for orientations away from 001, was found to be small in Rene N4. Analysis of recently published data on the single crystal superalloy PWA 1480 yielded the same result.

Miner, R. V.↗
NASA NTRS1990

A novel multistage estimation of signal parameters

A multistage estimation scheme is presented for estimating the parameters of a received carrier signal possibly phase-modulated by unknown data and experiencing very high Doppler, Doppler rate, etc. Such a situation arises, for example, in the case of the Global Positioning Systems (GPS). In the proposed scheme, the first-stage estimator operates as a coarse estimator of the frequency and its derivatives, resulting in higher rms estimation errors but with a relatively small probability of the frequency estimation error exceeding one-half of the sampling frequency (an event termed cycle slip). The second stage of the estimator operates on the error signal available from the first stage, refining the overall estimates, and in the process also reduces the number of cycle slips. The first-stage algorithm is a modified least-squares algorithm operating on the differential signal model and referred to as differential least squares (DLS). The second-stage algorithm is an extended Kalman filter, which yields the estimate of the phase as well as refining the frequency estimate. A major advantage of the is a reduction in the threshold for the received carrier power-to-noise power spectral density ratio (CNR) as compared with the threshold achievable by either of the algorithms alone.

Kumar, Rajendra↗
NASA NTRS1988

Space Cryogenics Workshop, University of Wisconsin, Madison, June 22, 23, 1987

Papers are presented on liquid helium servicing from the Space Station, performance estimates in the Superfluid Helium On-Orbit Transfer Flight Experiment, an analytical study of He II flow characteristics in the SHOOT transfer line, a Dewar to Dewar model for superfluid helium transfer, and mechanical pumps for superfluid helium transfer in space. Attention is also given to the cavitation characteristics of a small centrifugal pump in He I and He II, turbulent flow pressure drop in various He II transfer system components, slip effects associated with Knudsen transport phenomena in porous media, and an integrated fountain effect pump device for fluid management at low gravity. Other papers are on liquid/vapor phase separation in He-4 using electric fields, an enclosed capillary device for low-gravity management of He II, cavitation in flowing superfluid helium, the long-term performance of the passive thermal control systems of the IRAS spacecraft, and a novel approach to supercritical helium flight cryostat support structures.

Source record↗
NASA NTRS1990

An automatic editing algorithm for GPS data

An algorithm has been developed to edit automatically Global Positioning System data such that outlier deletion, cycle slip identification, and correction are independent of clock instability, selective availability, receiver-satellite kinematics, and tropospheric conditions. This algorithm, called TurboEdit, operates on undifferenced, dual frequency carrier phase data, and requires the use of P code pseudorange data and a smoothly varying ionospheric electron content. TurboEdit was tested on the large data set from the CASA Uno experiment, which contained over 2500 cycle slips.Analyst intervention was required on 1 percent of the station-satellite passes, almost all of these problems being due to difficulties in extrapolating variations in the ionospheric delay. The algorithm is presently being adapted for real time data editing in the Rogue receiver for continuous monitoring applications.

Blewitt, Geoffrey↗
NASA NTRS2011

The Parable of the Boiled Safety Professional

Common and unique issues contribute to system failures. This paper touches on the concept of drift to failure as a cautionary message. Managers and leaders, design team members, fabricators and assemblers, analysis and assurance personnel, and others associated with operating and maintaining systems, need to pay attention to identify the manifestation of individual and collective behaviors that might indicate slips in rigor or focus or decisions that might eat away at safety margins as our system drifts to failure. Corrections to drift made during design and development phases may efficiently prevent or mitigate drift problems occurring in the operational phase.

Shivers, Charles H.↗
NASA NTRS1987

The interpretation of crustal dynamics data in terms of plate interactions and active tectonics of the Anatolian Plate and surrounding regions in the Middle East

The primary effort in this study during the past year has been directed along two separate lines: (1) expanding finite element models to include the entire Anatolian plate, the Aegean Sea and the Northeastern Mediterranean Sea, and (2) investigating the relationship between fault geometry and earthquake activity for the North Anatolian and similar strike-slip faults (e.g., San Andreas Fault). Both efforts are designed to provide an improved basis for interpreting the Crustal Dynamics measurements NASA has planned for this region. The initial phases of both investigations have been completed and the results are being prepared for publication. These investigations are described briefly.

Toksoz, M. Nafi↗
NASA NTRS1989

The effects of particle loading on turbulence structure and modelling

The objective of the present research was to extend the Direct Numerical Simulation (DNS) approach to particle-laden turbulent flows using a simple model of particle/flow interaction. The program addressed the simplest type of flow, homogeneous, isotropic turbulence, and examined interactions between the particles and gas phase turbulence. The specific range of problems examined include those in which the particle is much smaller than the smallest length scales of the turbulence yet heavy enough to slip relative to the flow. The particle mass loading is large enough to have a significant impact on the turbulence, while the volume loading was small enough such that particle-particle interactions could be neglected. Therefore, these simulations are relevant to practical problems involving small, dense particles conveyed by turbulent gas flows at moderate loadings. A sample of the results illustrating modifications of the particle concentration field caused by the turbulence structure is presented and attenuation of turbulence by the particle cloud is also illustrated.

Squires, Kyle D.↗
NASA NTRS2000

Topographic Phase Recovery from Stacked ERS Interferometry and a Low-Resolution Digital Elevation Model

A hybrid approach to topographic recovery from ERS interferometry is developed and assessed. Tropospheric/ionospheric artifacts, imprecise orbital information, and layover are key issues in recovering topography and surface deformation from repeat-pass interferometry. Previously, we developed a phase gradient approach to stacking interferograms to reduce these errors and also to reduce the short-wavelength phase noise (see Sandwell arid Price [1998] and Appendix A). Here the method is extended to use a low-resolution digital elevation model to constrain long-wavelength phase errors and an iteration scheme to minimize errors in the computation of phase gradient. We demonstrate the topographic phase recovery on 16-m postings using 25 ERS synthetic aperture radar images from an area of southern California containing 2700 m of relief. On the basis of a comparison with 81 GPS monuments, the ERS derived topography has a typical absolute accuracy of better than 10 m except in areas of layover. The resulting topographic phase enables accurate two-pass, real-time interferometry even in mountainous areas where traditional phase unwrapping schemes fail. As an example, we form a topography-free (127-m perpendicular baseline) interferogram spanning 7.5 years; fringes from two major earthquakes and a seismic slip on the San Andreas Fault are clearly isolated.

Sandwell, David T.↗
NASA NTRS2006

Aeroheating Analysis for the Mars Reconnaissance Orbiter with Comparison to Flight Data

The aeroheating environment of the Mars Reconnaissance Orbiter (MRO) has been analyzed using the Direct Simulation Monte Carlo and free-molecular techniques. The results of these analyses were used to develop an aeroheating database to be used for the pre-flight planning and the in-flight operations support for the aerobraking phase of the MRO mission. The aeroheating predictions calculated for the MRO include the heat transfer coefficient (C(H)) over a range of angles-of-attack, side-slip angles, and number densities. The effects of flow chemistry were also investigated. Flight heat flux data deduced from surface temperature sensors have been compared to pre-flight predictions and agree favorably.

Liechty, Derek S.↗
NASA NTRS1984

Cenozoic rift formation in the northern Caribbean

Rifts form in many different tectonic environments where the lithosphere is put into extension. An outline is provided of the distribution, orientation, and relative ages of 16 Cenozoic rifts along the northern edge of the Caribbean plate and it is suggested that these structures formed successively by localized extension as the Caribbean plate moved eastward past a continental promontory of North America. Evidence leading to this conclusion includes (1) recognition that the rifts become progressively younger westward; (2) a two-phase subsidence history in a rift exposed by upthrusting in Jamaica; (3) the absence of rifts east of Jamaica; and (4) the observation that removal of 1400 km of strike-slip displacement on the Cayman Trough fault system places the Paleogene rifts of Jamaica in an active area of extension south of Yucatan where the rifts of Honduras and Guatemala are forming today.

Mann, P.↗
NASA NTRS2003

Short-term adaptation of the VOR: non-retinal-slip error signals and saccade substitution

We studied short-term (30 min) adaptation of the vestibulo-ocular reflex (VOR) in five normal humans using a "position error" stimulus without retinal image motion. Both before and after adaptation a velocity gain (peak slow-phase eye velocity/peak head velocity) and a position gain (total eye movement during chair rotation/amplitude of chair motion) were measured in darkness using search coils. The vestibular stimulus was a brief ( approximately 700 ms), 15 degrees chair rotation in darkness (peak velocity 43 degrees /s). To elicit adaptation, a straight-ahead fixation target disappeared during chair movement and when the chair stopped the target reappeared at a new location in front of the subject for gain-decrease (x0) adaptation, or 10 degrees opposite to chair motion for gain-increase (x1.67) adaptation. This position-error stimulus was effective at inducing VOR adaptation, though for gain-increase adaptation the primary strategy was to substitute augmenting saccades during rotation while for gain-decrease adaptation both corrective saccades and a decrease in slow-phase velocity occurred. Finally, the presence of the position-error signal alone, at the end of head rotation, without any attempt to fix upon it, was not sufficient to induce adaptation. Adaptation did occur, however, if the subject did make a saccade to the target after head rotation, or even if the subject paid attention to the new location of the target without actually looking at it.

Non-NASA Center↗
NASA NTRS1976

Eye movements during afterimage tracking under sinusoidal and random vestibular stimulation

The smooth portion of the horizontal vestibulo-ocular reflex was analyzed in terms of the frequency response, relating slow-phase eye velocity to angular velocity of a rotating chair under four different cases: sinusoidal rotation about a vertical axis in total darkness, sinusoidal rotation during afterimage tracking, pseudorandom head rotation in total darkness, and pseudorandom head rotation during afterimage tracking. Eye movements were recorded using a photoelectric limbus tracking method. The observation that the presence of an afterimage during vestibular stimulation increases the velocity of slow-phase eye movements is in support of the theory that such slow-phase movements are generated, at least in part, by the perceived velocity of the target. Since the target is immobilized on the retina, this perceived velocity is clearly not generated by retinal slip, but rather by a mechanism related to the eye movement such as corollary discharge.

Yasui, S.↗
NASA NTRS1986

Orientation and temperature dependence of some mechanical properties of the single-crystal nickel-base superalloy Rene N4. I - Tensile behavior

Single crystal specimens of a nickel-base superalloy with axes near 001, 011, and -112 were tested in tension at room temperature, 760, and 980 C. The alloy Rene N-4, was developed for gas turbine engine blades and has the nominal composition 3.7 Al, 4.2 Ti, 4 Ta, 0.5 Nb, 6 W, 1.5 Mo, 9 Cr, 7.5 Co, balance Ni, (all in weight percent). Analysis of slip band traces, specimen axis rotation, and dislocation Burgers vectors showed that at 760 and 980 C primary cube slip supplanted normal octahedral slip for the -112 line-oriented specimens. The other two orientations, which have lower resolved shear stresses on the cube system, exhibited octahedral slip at all three temperatures. The critical resolved shear stress is considerably greater on the cube system than on the octahedral system at room temperature. However, at 760 and 980 C the critical resolved shear stresses on the two systems are about the same. While the room temperature and 980 C yield strengths for the two orientations exhibiting octahedral slip could be rationalized on the basis of resolved shear stress, those at 760 C could not. Such violations of Schmid's law have previously been observed in other superalloys and single phase gamma-prime.

Miner, R. V.↗
NASA NTRS1999

TADS: A CFD-Based Turbomachinery Analysis and Design System with GUI: Methods and Results

The primary objective of this study was the development of a Computational Fluid Dynamics (CFD) based turbomachinery airfoil analysis and design system, controlled by a Graphical User Interface (GUI). The computer codes resulting from this effort are referred to as TADS (Turbomachinery Analysis and Design System). This document is the Final Report describing the theoretical basis and analytical results from the TADS system developed under Task 10 of NASA Contract NAS3-27394, ADPAC System Coupling to Blade Analysis & Design System GUI, Phase II-Loss, Design and. Multi-stage Analysis. TADS couples a throughflow solver (ADPAC) with a quasi-3D blade-to-blade solver (RVCQ3D) or a 3-D solver with slip condition on the end walls (B2BADPAC) in an interactive package. Throughflow analysis and design capability was developed in ADPAC through the addition of blade force and blockage terms to the governing equations. A GUI was developed to simplify user input and automate the many tasks required to perform turbomachinery analysis and design. The coupling of the various programs was done in such a way that alternative solvers or grid generators could be easily incorporated into the TADS framework. Results of aerodynamic calculations using the TADS system are presented for a multistage compressor, a multistage turbine, two highly loaded fans, and several single stage compressor and turbine example cases.

Koiro, M. J.↗
NASA NTRS1989

A novel multistage estimation of the signal parameters of a possibly data-modulated sinusoid under very high dynamics

A novel multistage estimation scheme is presented for estimating the parameters of a received carrier signal possibly phase-modulated by unknown data, and experiencing very high Doppler, Doppler rate, etc. Such a situation arises, for example, in the case of Global Positioning Systems (GPS) where the signal parameters are directly related to the position, velocity, acceleration and jerk of the GPS receiver. In the proposed multistage scheme, the first stage estimator operates as a coarse estimator resulting in higher rms estimation errors but with a relatively small probability of the frequency estimation error exceeding one-half of the sampling frequency (an event termed cycle slip). The second state of the estimator operates on the error signal available from the first stage, refining the overall estimates, and in the process also reduces the number of cycle slips. The first stage algorithm is selected to be a modified least squares algorithm operating upon the differential signal model and referred to as differential least squares. This estimation stage provides relatively coarse estimates of the frequency and its derivatives. The second algorithm is simply an extended Kalman filter which also yields the estimate of the phase along with a more refined estimate of frequency as well. A major advantage of the proposed algorithm is a reduction in the threshold on received carrier power-to-noise power spectral density ratio as compared to the threshold achievable by either of these algorithms alone. In fact, it appears from the simulations that for the case of an unmodulated carrier, the proposed scheme achieves the same threshold as for an almost exact and computationally intensive implementation of the maximum likelihood estimator.

Kumar, Rajendra↗
NASA NTRS2006

Properties of a Ni(sub 19.5)Pd(sub 30)Ti(sub 50.5) high-temperature shape memory alloy in tension and compression

Potential applications involving high-temperature shape memory alloys have been growing in recent years. Even in those cases where promising new alloys have been identified, the knowledge base for such materials contains gaps crucial to their maturation and implementation in actuator and other applications. We begin to address this issue by characterizing the mechanical behavior of a Ni19.5Pd30Ti50.5 high-temperature shape memory alloy in both uniaxial tension and compression at various temperatures. Differences in the isothermal uniaxial deformation behavior were most notable at test temperatures below the martensite finish temperature. The elastic modulus of the material was very dependent on strain level; therefore, dynamic Young#s Modulus was determined as a function of temperature by an impulse excitation technique. More importantly, the performance of a thermally activated actuator material is dependent on the work output of the alloy. Consequently, the strain-temperature response of the Ni19.5Pd30Ti50.5 alloy under various loads was determined in both tension and compression and the specific work output calculated and compared in both loading conditions. It was found that the transformation strain and thus, the specific work output were similar regardless of the loading condition. Also, in both tension and compression, the strain-temperature loops determined under constant load conditions did not close due to the fact that the transformation strain during cooling was always larger than the transformation strain during heating. This was apparently the result of permanent plastic deformation of the martensite phase with each cycle. Consequently, before this alloy can be used under cyclic actuation conditions, modification of the microstructure or composition would be required to increase the resistance of the alloy to plastic deformation by slip.

Noebe, Ronald↗
NASA NTRS2004

Multilayer Fiber Interfaces for Improved Environmental Resistance and Slip in Carbon Fiber Reinforced Composites

Ultraviolet-enhanced chemical vapor deposition (UVCVD) has been developed to lower the required substrate temperature thereby allowing for the application of metal oxide-based coatings to carbon and ceramic fibers without causing significant fiber damage. An effort to expand this capability to other ceramic phases chosen to maximize oxidation protection in the likely event of matrix cracking and minimize possible reaction between the coating and fiber during long-term high temperature use will be presented along with studies aimed at the demonstration of these and other benefits for the next-generation interface coating systems being developed herein.

Babcock, Jason R.↗