Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PENETRATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Sonic Boom Ocean Penetration: Noise Metric Comparison and Initial Focusing Results

The purpose of the present research is to determine the impact by sonic boom noise penetration into the ocean. Since the 1994 LaRC High Speed Research Program Sonic Boom Workshop several new results have been obtained. This talk reviews these results, and emphasizes the two most important findings. The first major result is an improved understanding of the noise spectra of the penetrating sonic boom. It was determined that weighted sound exposure levels decrease with deeper ocean depths significantly faster than unweighted sound exposure levels. This is because low frequencies penetrate the ocean deeper than high frequencies. Several noise metrics were used including peak, SEL, C-SEL, A-SEL, and PLdB, and results are given for all. These results are important because they show that the sonic boom noise impact on marine life a few meters below the ocean surface may be significantly lower using weighted sound levels than if one were to measure the impact using unweighted levels. The other major finding is the first estimate of the worst case peak levels produced by a penetrating sonic boom being focused by a sinusoidal ocean surface. The method of analysis chosen was computational, a time domain finite difference algorithm. The method is outlined and then example results are presented. For rounded sonic boom waveforms incident on a sinusoidal ocean surface, it is shown that the percentage increase or decrease in pressure is only occasionally larger than 10%, rarely 25%. These fluctuations indicate, under the assumptions already given, that any increase or decrease in sound level underwater due to focusing or defocusing should be small, less than 3 dB.

Sparrow, Victor W.↗
NASA NTRS2000

A Trade Study and Metric for Penetration and Sampling Devices for Possible Use on the NASA 2003 and 2005 Mars Sample Return Missions

The scientific exploration of Mars will require the collection and return of subterranean samples to Earth for examination. This necessitates the use of some type of device or devices that possesses the ability to effectively penetrate the Martian surface, collect suitable samples and return them to the surface in a manner consistent with imposed scientific constraints. The first opportunity for such a device will occur on the 2003 and 2005 Mars Sample Return missions, being performed by NASA. This paper reviews the work completed on the compilation of a database containing viable penetrating and sampling devices, the performance of a system level trade study comparing selected devices to a set of prescribed parameters and the employment of a metric for the evaluation and ranking of the traded penetration and sampling devices, with respect to possible usage on the 03 and 05 sample return missions. The trade study performed is based on a select set of scientific, engineering, programmatic and socio-political criterion. The use of a metric for the various penetration and sampling devices will act to expedite current and future device selection.

McConnell, Joshua B.↗
NASA NTRS2009

Effect of Crack Opening on Penetrant Crack Detectability

Results: From the testing we were able to determine all the cracks within the test range were detectable or better with developer. Many of the indications after development lost their linearity and gave circular indications. Our tests were performed in a laboratory and our procedure would be difficult in an industrial setting. Conclusions: The "V" did not significantly affect our ability to detect the POD cracks with fluorescent penetrant. Conduct same experiment with more cracks. The 0.025 and 0.050 POD specimens are clean and documented with the SEM. Conduct water-wash fluorescent penetrant test at EAFB. The poppet cracks are tighter than the POD specimen cracks. Flight FCV poppets: 0.01 mils (0.3 microns) Langley fatigue cracked poppets: 0.02 mils (0.5 microns) POD specimen (post 5 mils): 0.05 mils (1.4 microns) We could not detect cracks in Langley fatigue-cracked poppets with fluorescent penetrant. Investigate inability of penetrant to wet the poppet surface.

Weaver, Devin↗
NASA NTRS2005

Depth-Penetrating Luminescence Thermography of Thermal- Barrier Coatings

A thermographic method has been developed for measuring temperatures at predetermined depths within dielectric material layers . especially thermal-barrier coatings. This method will help satisfy a need for noncontact measurement of through-the-thickness temperature gradients for evaluating the effectiveness of thermal- barrier coatings designed to prevent overheating of turbine blades, combustor liners, and other engine parts. Heretofore, thermography has been limited to measurement of surface and near-surface temperatures. In the thermographic method that is the immediate predecessor of the present method, a thermographic phosphor is applied to the outer surface of a thermal barrier coating, luminescence in the phosphor is excited by illuminating the phosphor at a suitable wavelength, and either the time dependence of the intensity of luminescence or the intensities of luminescence spectral lines is measured. Then an emissivity-independent surface-temperature value is computed by use of either the known temperature dependence of the luminescence decay time or the known temperature dependence of ratios between intensities of selected luminescence spectral lines. Until now, depth-penetrating measurements have not been possible because light of the wavelengths needed to excite phosphors could not penetrate thermal-barrier coating materials to useful depths. In the present method as in the method described above, one exploits the temperature dependence of luminescence decay time. In this case, the phosphor is incorporated into the thermal-barrier coat at the depth at which temperature is to be measured. To be suitable for use in this method, a phosphor must (1) exhibit a temperature dependence of luminescence decay time in the desired range, (2) be thermochemically compatible with the thermal-barrier coating, and (3) exhibit at least a minor excitation spectral peak and an emission spectral peak, both peaks being at wavelengths at which the thermal-barrier coating is transparent or at least translucent. Conventional thermographic phosphors are not suitable because they are most efficiently excited by ultraviolet light, which does not penetrate thermal- barrier coating materials. (Typical thermal-barrier coating materials include or consist of various formulations of yttria-stabilized zirconia.) Only a small fraction of phosphor candidates have significant excitation at wavelengths long enough (>500 nm) for sufficient penetration of thermal-barrier coatings. One suitable phosphor material . yttria doped with europium (Y2O3:Eu) . has a minor excitation peak at 532 nm and an emission peak at 611 nm. In experiments, this material was incorporated beneath a 100-microns-thick thermal-barrier coating and subjected to excitation and measurement by the luminescence-decay-time technique. These experiments were found to yield reliable temperature values up to 1,100 C. At the time of reporting the information for this article, a search for suitable phosphors other than (Y2O3:Eu) was continuing.

Eldridge, Jeffrey↗
NASA NTRS2012

Evaluate Techniques for Penetrating a Shielded Enclosure Using Twisted Pair Wire

The aim of this project is to demonstrate techniques for effectively penetrating a radio shielded enclosure using Ethernet cable (CAT-6). This process requires that we measure the shielding performance by means of testing and data orchestration to collect and analyze our data to present observations with different test cases. Each test case would represent a different penetration strategy that utilizes distinctive wire coupling and characteristics (i.e. the type of bulkhead link, the twist of each CAT-6 cable, the shielding type of each CAT-6 cable, and the length of the cable). As the different cable setups are fabricated a prototype evaluation of setup is conducted to measure the signal integrity of our testing configuration. Our signal integrity is measured through the analysis of different parameters found in the prototype evaluation such as RF leakage, impedance mismatch, and decay rate. As each of these data values are effectively collected and analyzed the most effective cable setup is selected based upon its ability to penetrate the shielded enclosure. The testing data is compared in conjunction with the cost of the manufacturing of the prototype wire penetration.

St. Julian, Christopher↗
NASA NTRS2016

Dye Penetrant Crack Detectability in External Corners in Presence of Fillet Radius

NASA uses special dye penetrant nondestructive evaluation process to provide reliable detection of very small cracks. Typically the surface crack lengths sizes are 0.030' and 0.050' for special dye penetrant process. Qualification requires demonstration of crack detection on a set of cracks with average crack size smaller than or equal to the qualification crack size. The demonstration is called point estimate demonstration. A set of corner cracks can be used to determine reliably detectable corner crack using the point estimate demonstration method. However, dye penetrant demonstration on surface cracks can be used to assess reliably detectable corner crack sizes by using similarity in the penetrant process. The paper provides similarity analysis approach for determining the reliably detectable corner crack sizes for given a point estimate demonstrated surface crack size.

Koshti, Ajay M.↗
DOE OSTI2022

Design and Use of a Penetrating Deposition Nozzle for Z-Pinning Additive Manufacturing

Fused Filament Fabrication (FFF) involves depositing material layer-by-layer to create athree-dimensional object. This method often demonstrates high mechanical anisotropy in theprinted structure, leading to a drop in the material strength of the part when comparing structuresalong the deposition plane (X/Y-Axis) versus across layers in the build direction (Z-Axis). Initialefforts to improve anisotropy led to the development of the Z-Pinning process, where continuouspins are deposited across layers in the Z-Axis. Z-pinning has demonstrated significant gains intoughness and inter-layer strength, particularly in fiber-reinforced materials. However, thisprocess can also create flaws in the structure that increase in severity and frequency as the pinsgrow in length and diameter. To mitigate this, a penetrating nozzle has been developed thatextends a fine-tipped extrusion nozzle deep into the pin cavity and simultaneously extrudesmaterial as it retracts. This study investigates the printability of the penetrating nozzle for simplegeometries and evaluates the resulting Z-pinning mesostructure. As a result of this study, theprototype penetrating nozzle design was analyzed and built. Through a pressure driven flowanalysis it was determined that the penetrating nozzle extruder can not only flow extrudefilament. After a transient thermal simulation it was found that after a pause of 15 secondsresume printing with no drop in heat at nozzle exit.

Bales, Brenin↗
DOE OSTI2020

Techno-economic analysis of the impact of dynamic electricity prices on solar penetration in a smart grid environment with distributed energy storage

This study investigates the technical and economic feasibility of using high levels of solar energy penetration up to 400 MW into a smart grid system of 60,000 smart houses. A novel non-cooperative Stackelberg game is introduced that incorporates the profitability of the supply-side and helps in solving problems related to overgeneration and photovoltaic curtailment. The non-cooperative game is intended to find the optimal dynamic prices that would leverage distributed storage through the demand-side to stabilize the power grid operation. Ten cases are studied with five photovoltaic plant sizes and two battery designs. Here, a novel quantitative analysis of high levels of solar penetration as a percentage of the total electricity demand is introduced to evaluate the technical feasibility of the studied cases. To evaluate the economic viability of the proposed smart grid system, four metrics were used: the levelized cost of energy, the levelized cost of storage, the payback period, and the net present value. Two out of ten studied cases were concluded to be the most promising cases, one with a solar photovoltaic plant size of 200 MW and the other with 300 MW. The case with 300 MW solar plant is preferred as it paves the way for more solar energy deployment with a solar penetration percentage up to 67.78%. This case had a payback period of 10.72 years and a net present value of $\$51.44$ M for the solar plant and a payback period of 12.06 years and a net present value of $\$40.75$ M for the demand-side.

14 SOLAR ENERGY↗
DOE OSTI2023

London penetration depth of electron-irradiated Ba 0 . 47 K 0 . 53 Fe 2 As 2

We have characterized an electron-irradiated Ba 1-x K x Fe 2 As 2 (x = 0.53) single-crystal using two different experimental techniques: magneto-optic measurements and microwave measurements. The crystal has been measured before as well as after the 2.5 MeV electron irradiation process. After irradiation it was annealed in a number of steps, between 90 °C and 180 °C, and measured after each annealing step. Most microwave measurements were performed by means of a copper cavity, taking advantage of the TE 011 and TM 110 modes, allowing for the determination of the London penetration depths changes δλ ab (T) and δλ c (T), ie perpendicular and parallel to the sample c-axis. Appropriate equations, based on perturbation theory, were derived to calculate the penetration depths changes δλ ab and δλ c for a rectangular prism geometry. The sample showed a full recovery of its T c , however the observed behavior of δλ c and δλ ab was not monotonic vs annealing temperature, displaying a minimum of δλ c and δλ ab at 120 °C. In conclusion, this finding was confirmed by magneto-optic measurements, where besides verifying the sample uniformity and the absence of visible defects, the lower critical field H c1 of the Ba 1-x K x Fe 2 As 2 single-crystal was obtained and the London penetration depth λab(0) was calculated.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Stability Impact of IEEE 1547 Operational Mode Changes Under High DER Penetration in the Presence of Cyber Adversary

The IEEE 1547 standard addresses the integration of Distributed Energy Resources (DER) into Area Electric Power Systems (AEPS). The updated standard, released in 2018 with revisions ongoing, specifies the need for more flexible settings, requiring the DER to remain connected during certain disturbances and provide voltage support via active and reactive power modes. With these increased capabilities comes increased risks, and our analysis of the standard has produced potential settings combinations, which, while allowable under the standard, may actually create instability. This contradicts the main purpose of the revised standard. Since the DER must support a communication interface through which the AEPS operator can change settings, adversarial mode changes are possible via a cyberattack. This concern is heightened as DER penetration increases, where under a reasonable threat model, an attacker could affect multiple DER simultaneously. We have conducted a simulation analysis of potentially adverse combinations of mode change and ridethrough parameters on a hypothetical AEPS with varying degrees of DER penetration. We conclude that certain adverse mode changes, whether through error or cyberattack, can lead to unstable conditions with DER penetrations as low as 24% of the AEPS system capacity.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS2006

Miniature Ground Penetrating Radar, CRUX GPR

Under NASA instrument development programs (PIDDP 2000-2002, MIPD 2003-2005, ESR and T, 2005) we have been developing miniature ground penetrating radars (GPR) for use in mapping subsurface stratigraphy from planetary rovers for Mars and lunar applications. The Mars GPR is for deeper penetration (up to 50 m depth) into the Martian subsurface at moderate resolution (0.5 m) for a geological characterization. As a part of the CRUX (Construction and Resource Utilization Explorer) instrument suite, the CRUX GPR is optimized for a lunar prospecting application. It will have shallower penetration (5 m depth) with higher resolution (10 cm) for construction operations including ISRU (in-situ resource utilization).

ground penetrating radars (GPR↗
DOE OSTI2024

Utility Perspective on Protection Challenges with High IBR Penetration [Slides]

Utilities have seen rapid increase in Solar, Wind, and Battery Energy Storage Resources that interconnect to their electric system through Inverters. Inverter-Based Resources (IBRs) have fault current characteristics that are unlike the fault current response of traditional rotating-machine-based generators, which is well known and repeatable. IBR’s non-traditional fault current behavior is due to the IBR control scheme, which is configured to provide a clean AC output but also protect the inverter’s sensitive power electronics devices from damage, one source of which is overcurrent. This results in low fault current magnitude, low or no negative sequence current injection, the variability of sequence component currents, the variability of voltage with respect to current angles, and the lack of inertia. The control scheme also results in a fault current response that can vary between manufactures and between models of the same manufacturer. High penetration of IBRs can adversely affect the protection schemes applied in areas with high penetration of IBRs. With the proliferation of IBRs, utilities are finding out that conventional protection schemes are not adequately equipped to protect the electric systems. This is mainly because the existing protection elements and practices have been designed based on the fault current response of conventional rotating machines. In several cases, the available literature does not provide any clear solution for the issues when the protection scheme does not operate properly near IBRs. This report identifies various protection challenges due to IBRs that industry is facing, from the utility perspective. Instead of facing on one issue, this report looks broadly on all the challenges that system protection has experienced with high penetration of IBRs. Based on the IBR response from various utilities during real fault events and gathering perspective from different utility SMEs via questionnaire, the report summarizes on gathered data and internal experiences.

14 SOLAR ENERGY↗
DOE OSTI2025

Pursuing small-scale measures of penetration resistance in Ti-5553 alloy

This work was originally proposed to illustrate the performance of a particular set of differently processed Ti-5553 plates under dynamic threats. It became clear that the larger question, at present, is whether the small-scale shaped charge design of an RP-4 detonator can be employed to efficiently explore the dynamic penetration resistance of representative test articles. The initial penetration testing that employed three variants of thermomechanical processing of Ti-5553 plates appeared to demonstrate that there was a noticeable difference in their performance. The remaining pertinent question was regarding the variation in the shaped charge performance and how it compares to the variation from the three titanium plate tests. Based on the limited testing presented here the RP-4 shaped charge detonator appears to have an average depth of penetration in 6061 aluminum of 90mm with a 1.5CD stand off.

shaped charge penetration↗
DOE OSTI2021

Penetration of Fission Products Ions into Complex Solids and the Effect of Ionic Wash Methods

During washing of radiologically impacted building surfaces, penetration of radionuclide ions into complex solids associated with these surfaces may occur. This study investigates the penetration of Cs-137, Sr-85, and Eu-152 solutions into numerous common building materials and radionuclide behavior when these materials were exposed to a static bath or low-pressure flow of tap water, 0.1 M potassium chloride (KCl), and 0.5 M KCl. The decontamination efficacy and the depth profile for residual contamination were measured to determine the conditions under which applying a wash solution has benefit compared to physically removing the surface material. On asphalt, 70-80% of the radionuclides were found to be within 0.02 mm of the surface. Concrete is more porous than asphalt, and 80% of the radionuclides were within 0.2 mm of the surface for Cs-137 and Eu-152 and 50-80% for Sr-85. Water effectively removed all contaminants from hard nonporous surfaces. Finally, this paper illustrates that a wash penalty factor concept-defined as ratio of the depth at which 50% of the radioactivity is found in the washed sample divided by the depth at which 50% of radioactivity is found in the control-can serve as a way to quantify whether the wash method increases the depth at which contamination penetrates into the material and thus the material becomes more difficult to decontaminate.

building materials↗
DOE OSTI2025

Symmetry structure of a Riccati equation appearing in penetration mechanics

In the design of projectile penetration experiments a matter of considerable interest is scaling: that is, the potential relevance of small-scale experiments to their full-scale counterparts, in a manner analogous to that most often encountered in the context of fluid mechanics. From the theoretical standpoint, phenomena associated with scaling and scalability can be assessed using the well-established tools of dimensional analysis and the Buckingham-Pi Theorem. However, the familiar precepts of dimensional analysis are themselves a specific manifestation of the broader group invariance properties or symmetries of a mathematical model. Here, this work explores these notions – that is, dimensional analysis, the conditions for realizing complete similarity, and any additional symmetry structures – in the context of a Riccati differential equation appearing in the context of penetration mechanics. The aim of the investigation is twofold: 1) to complement existing empirical considerations with a concrete theoretical basis, and 2) to provide a deeper theoretical understanding of the projectile penetration model and its many implications.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Grid ancillary services using electrolyzer-Based power-to-Gas systems with increasing renewable penetration

Increasing penetrations of renewable-based generation have led to a decrease in the bulk power system inertia and an increase in intermittency and uncertainty in generation. Energy storage is considered to be an important factor to help manage renewable energy generation at greater penetrations. Hydrogen is a viable long-term storage alternative. This paper analyzes and presents use cases for leveraging electrolyzer-based power-to-gas systems for electric grid support. The paper also discusses some grid services that may favor the use of hydrogen-based storage over other forms such as battery energy storage. Real-time controls are developed, implemented and demonstrated using a power-hardware-in-the-loop(PHIL) setup with a 225-kW proton-exchange-membrane electrolyzer stack. These controls demonstrate frequency and voltage support for the grid for different levels of renewable penetration (0%, 25%, and 50%). A comparison of the results shows the changes in respective frequencies and voltages as seen as different buses as a result of support from the electrolyzers and notes the impact on hydrogen production as a result of grid support. Finally, the paper discusses the practical nuances of implementing the tests with physical hardware, such as inverter/electrolyzer efficiency, as well as the related constraints and opportunities.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

Impact of Penetrating Kelvin Waves on MJO Rainfall Propagation Through Deep Convection Modulation

The Madden‐Julian Oscillation (MJO) is a dominant intraseasonal oscillation in the tropics. As MJOs propagate over the Indian Ocean, some of them can be penetrated by fast‐moving equatorial Kelvin waves originating to the west of the MJOs. Through a series of sensitivity experiments, we demonstrate that these penetrating Kelvin waves can modulate the eastward propagation speed of MJO rainfall. Deep convection in the western MJO rainfall envelope initiates more frequently and produces greater lifetime rainfall when a convectively active Kelvin phase is present, while the opposite occurs during a convectively suppressed Kelvin phase. This alteration in deep convection activity can lead to notable changes in the propagation of the large‐scale MJO rainfall envelope. The modulation of deep convection lifetime rainfall by penetrating Kelvin waves primarily occurs through their impact on deep convection rainfall area, which is closely related to the variations in lower‐tropospheric moisture induced by the Kelvin waves.

Chen, Xingchao [Pennsylvania State Univ., Universi↗
DOE OSTI2021

Multiseriate cortical sclerenchyma enhance root penetration in compacted soils

Mechanical impedance limits soil exploration and resource capture by plant roots. We examine the role of root anatomy in regulating plant adaptation to mechanical impedance and identify a root anatomical phene in maize (Zea mays) and wheat (Triticum aestivum) associated with penetration of hard soil: Multiseriate cortical sclerenchyma (MCS). We characterize this trait and evaluate the utility of MCS for root penetration in compacted soils. Roots with MCS had a greater cell wall-to-lumen ratio and a distinct UV emission spectrum in outer cortical cells. Genome-wide association mapping revealed that MCS is heritable and genetically controlled. We identified a candidate gene associated with MCS. Across all root classes and nodal positions, maize genotypes with MCS had 13% greater root lignin concentration compared to genotypes without MCS. Genotypes without MCS formed MCS upon exogenous ethylene exposure. Genotypes with MCS had greater lignin concentration and bending strength at the root tip. In controlled environments, MCS in maize and wheat was associated improved root tensile strength and increased penetration ability in compacted soils. Maize genotypes with MCS had root systems with 22% greater depth and 49% greater shoot biomass in compacted soils in the field compared to lines without MCS. Of the lines we assessed, MCS was present in 30 to 50% of modern maize, wheat, and barley cultivars but was absent in teosinte and wild and landrace accessions of wheat and barley. MCS merits investigation as a trait for improving plant performance in maize, wheat, and other grasses under edaphic stress.

54 ENVIRONMENTAL SCIENCES↗