Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Oscillatory Components”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Development of a spinning wave heat engine

A theoretical analysis and an experimental investigation were conducted to assess the feasibility of developing a spinning wave heat engine. Such as engine would utilize a large amplitude traveling acoustic wave rotating around a cylindrica chamber, and it should not suffer from the inefficiency, noise, and intermittent thrust which characterizes pulse jet engines. The objective of this investigation was to determine whether an artificially driven large amplitude spinning transverse wave could induce a steady flow of air through the combustion chamber under cold flow conditions. In the theoretical analysis the Maslen and Moore perturbation technique was extended to study flat cylinders (pancake geometry) with completely open side walls and a central opening. In the parallel experimental study, a test moel was used to determine resonant frequencies and radial pressure distributions, as well as oscillatory and steady flow velocities at the inner and outer peripheries. The experimental frequency was nearly the same as the theoretical acoustic value for a model of the same outer diameter but without a central hole. Although the theoretical analysis did not predict a steady velocity component, simulaneous measurements of hotwire and microphone responses have shown that the spinning wave pumps a mean flow radially outward through the cavity.

Zinn, B. T.↗

Fluid mechanics experiments in oscillatory flow. Volume 1: Report

Results of a fluid mechanics measurement program in oscillating flow within a circular duct are presented. The program began with a survey of transition behavior over a range of oscillation frequency and magnitude and continued with a detailed study at a single operating point. Such measurements were made in support of Stirling engine development. Values of three dimensionless parameters, Re(sub max), Re(sub w), and A(sub R), embody the velocity amplitude, frequency of oscillation and mean fluid displacement of the cycle, respectively. Measurements were first made over a range of these parameters which included operating points of all Stirling engines. Next, a case was studied with values of these parameters that are representative of the heat exchanger tubes in the heater section of NASA's Stirling cycle Space Power Research Engine (SPRE). Measurements were taken of the axial and radial components of ensemble-averaged velocity and rms-velocity fluctuation and the dominant Reynolds shear stress, at various radial positions for each of four axial stations. In each run, transition from laminar to turbulent flow, and its reverse, were identified and sufficient data was gathered to propose the transition mechanism. Models of laminar and turbulent boundary layers were used to process the data into wall coordinates and to evaluate skin friction coefficients. Such data aids in validating computational models and is useful in comparing oscillatory flow characteristics to those of fully-developed steady flow. Data were taken with a contoured entry to each end of the test section and with flush square inlets so that the effects of test section inlet geometry on transition and turbulence are documented. Volume 1 contains the text of the report including figures and supporting appendices. Volume 2 contains data reduction program listings and tabulated data (including its graphical presentation).

Seume, J.↗

Nonlinear Aeroelastic Analysis of the HIAD TPS Coupon in the NASA 8' High Temperature Tunnel: Theory and Experiment

The purpose of this work is to develop a set of theoretical and experimental techniques to characterize the aeroelasticity of the thermal protection system (TPS) on the NASA Hypersonic Inflatable Aerodynamic Decelerator (HIAD). A square TPS coupon experiences trailing edge oscillatory behavior during experimental testing in the 8' High Temperature Tunnel (HTT), which may indicate the presence of aeroelastic flutter. Several theoretical aeroelastic models have been developed, each corresponding to a different experimental test configuration. Von Karman large deflection theory is used for the plate-like components of the TPS, along with piston theory for the aerodynamics. The constraints between the individual TPS layers and the presence of a unidirectional foundation at the back of the coupon are included by developing the necessary energy expressions and using the Rayleigh Ritz method to derive the nonlinear equations of motion. Free vibrations and limit cycle oscillations are computed and the frequencies and amplitudes are compared with accelerometer and photogrammetry data from the experiments.

Benjamin D. Goldman↗

Topological Data Analysis for Particulate Gels

Soft gels, formed via the self-assembly of particulate materials, exhibit intricate multiscale structures that provide them with flexibility and resilience when subjected to external stresses. Here, this work combines particle simulations and topological data analysis (TDA) to characterize the complex multiscale structure of soft gels. Our TDA analysis focuses on the use of the Euler characteristic, which is an interpretable and computationally scalable topological descriptor that is combined with filtration operations to obtain information on the geometric (local) and topological (global) structure of soft gels. We reduce the topological information obtained with TDA using principal component analysis (PCA) and show that this provides an informative low-dimensional representation of the gel structure. We use the proposed computational framework to investigate the influence of gel preparation (e.g., quench rate, volume fraction) on soft gel structure and to explore dynamic deformations that emerge under oscillatory shear in various response regimes (linear, nonlinear, and flow). Our analysis provides evidence of the existence of hierarchical structures in soft gels, which are not easily identifiable otherwise. Moreover, our analysis reveals direct correlations between topological changes of the gel structure under deformation and mechanical phenomena distinctive of gel materials, such as stiffening and yielding. In summary, we show that TDA facilitates the mathematical representation, quantification, and analysis of soft gel structures, extending traditional network analysis methods to capture both local and global organization.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An Experimental Study of Pressure Oscillation in a Capillary Pumped Loop with Multiple Evaporators and Condensers

The heat transport capability of a capillary pumped loop (CPL) is limited by the pressure drop that its evaporator wick can sustain. The pressure drop in a CPL is not constant even under seemingly steady operation, but rather exhibits an oscillatory behavior. A hydrodynamic theory based on a mass-spring-dashpot model was previously developed to predict the pressure oscillation in a CPL with a single evaporator and a single condenser. The theory states that the pressure oscillation is a function of physical dimensions of the CPL components and operating conditions. Experimental data agreed very well with theoretical predictions. The hydrodynamic stability theory has recently been extended to predict the pressure oscillations in CPLs with multiple evaporators and multiple condensers. Concurrently, an experimental study was conducted to verify the theory and to investigate the effects of various parameters on the pressure oscillation. Four evaporators with different wick properties were tested using a test loop containing two condenser plates. The test loop allowed the four evaporators to be tested in a single-pump, two-pump or four-pump configuration, and the two condenser plates to be plumbed either in parallel or in series. Test conditions included varying the power input, the reservoir set point temperature, the condenser sink temperature, and the flow resistance between the reservoir and the loop. Experimental results agreed well with theoretical predictions.

Ku, Jen-Tung↗

Properties of Supergranulation During the Solar Minima of Cycles 22/23 and 23/24

The solar minimum at the transition from cycle 23 to 24 was notable for its low level of activity and its extended duration. Among the various fields of study, the evolution of the solar convection zone may provide insight into the causes and consequences of this recent minimum. This study continues previous investigations of the characteristics of solar supergranulation, a convection component strongly linked to the structure of the magnetic field, namely the time-evolution of the global mean of supergranule cell size, determined from spectral analysis of MDI Dopplergrams from the two previous solar minima. Analyses of the global mean of supergranule sizes show a quasi-oscillatory nature to the evolution of this particular supergranule characteristic. Performing similar analyses on realistic, synthetic Doppler images show similar time-dependent characteristics. We conclude that the observed fluctuations are not observational artifacts, and that an underlying trend exists within the evolution of the supergranulation network.

Williams, Peter E.↗

Analysis of Wind Tunnel Oscillatory Data of the X-31A Aircraft

Wind tunnel oscillatory tests in pitch, roll, and yaw were performed on a 19%-scale model of the X-31A aircraft. These tests were used to study the aerodynamic characteristics of the X-31A in response to harmonic oscillations at six frequencies. In-phase and out-of-phase components of the aerodynamic coefficients were obtained over a range of angles of attack from 0 to 90 deg. To account for the effect of frequency on the data, mathematical models with unsteady terms were formulated by use of two different indicial functions. Data from a reduced set of frequencies were used to estimate model parameters, including steady-state static and dynamic stability derivatives. Both models showed good prediction capability and the ability to accurately fit the measured data. Estimated static stability derivatives compared well with those obtained from static wind tunnel tests. The roll and yaw rate derivative estimates were compared with rotary-balanced wind tunnel data and theoretical predictions. The estimates and theoretical predictions were in agreement at small angles of attack. The rotary-balance data showed, in general, acceptable agreement with the steady-state derivative estimates.

Smith, Mark S.↗

A finite-element analysis for steady and oscillatory subsonic flow around complex configurations

The problem of potential subsonic flow around complex configurations is considered. The solution is given of an integral equation relating the values of the potential on the surface of the body to the values of the normal derivative, which is known from the boundary conditions. The surface of the body is divided into small (hyperboloidal quadrilateral) surface elements, which are described in terms of the Cartesian components of the four corner points. The values of the potential (and its normal derivative) within each element is assumed to be constant and equal to its value at the centroid of the element. The coefficients of the equation are given by source and doublet integrals over the surface elements. Closed form evaluations of the integrals are presented. The results obtained with the above formulation are compared with existing analytical and experimental results.

Chen, L. T.↗

Stimulated Raman up-conversion of electromagnetic waves by a gyrating electron beam

A gyrating electron beam supports negative energy modes near the harmonics of electron-cyclotron frequency. An electromagnetic wave passing through such a beam parametrically up-converts into high-frequency electromagnetic modes separated from the pump frequency by the electron-cyclotron harmonics. The growth rate for this process varies directly as the oscillatory velocity of beam electrons caused by the pump and as square root of the beam density. It has a maximum at values of scattering angle close to 180 deg and is also implicitly dependent on the beam veocity and the cyclotron frequency of electrons. The effect of a cold electron component is to reduce the growth rate.

Sharma, O. P.↗

Analysis of Wind Tunnel Lateral Oscillatory Data of the F-16XL Aircraft

Static and dynamic wind tunnel tests were performed on an 18% scale model of the F-16XL aircraft. These tests were performed over a wide range of angles of attack and sideslip with oscillation amplitudes from 5 deg. to 30 deg. and reduced frequencies from 0.073 to 0.269. Harmonic analysis was used to estimate Fourier coefficients and in-phase and out-of-phase components. For frequency dependent data from rolling oscillations, a two-step regression method was used to obtain unsteady models (indicial functions), and derivatives due to sideslip angle, roll rate and yaw rate from in-phase and out-of-phase components. Frequency dependence was found for angles of attack between 20 deg. and 50 deg. Reduced values of coefficient of determination and increased values of fit error were found for angles of attack between 35 deg. and 45 deg. An attempt to estimate model parameters from yaw oscillations failed, probably due to the low number of test cases at different frequencies.

Klein, Vladislav↗

Emergent electric field induced by dissipative sliding dynamics of domain walls in a Weyl magnet

The dynamic motion of topological defects in magnets induces an emergent electric field, as exemplified by the continuous flow of skyrmion vortices. However, the electrodynamics underlying this emergent field remains poorly understood. In this context, magnetic domain walls—one-dimensional topological defects with two collective modes, sliding and spin-tilt—offer a promising platform for exploration. Here we demonstrate that the dissipative motion of domain walls under oscillatory current excitation generates an emergent electric field. We image domain patterns and quantify the domain-wall length under applied magnetic fields in mesoscopic devices based on the magnetic Weyl semimetal NdAlSi. These devices exhibit exceptionally strong domain-wall scattering and a pronounced emergent electric field, as observed in the imaginary component of the complex impedance. Spin dynamics simulations reveal that domain-wall sliding dominates over spin-tilting, in which the phase delay of the domain-wall motion with respect to the driving force impacts the emergent electric field. Our findings establish domain-wall dynamics as a platform for studying emergent electromagnetic fields and motivate further investigations of the coupled motion of magnetic solitons and conduction electrons.

Yamada, Rinsuke [The University of Tokyo, Japan]↗

A finite-element analysis for steady and oscillatory supersonic flows around complex configurations

The problem of small perturbation potential supersonic flow around complex configurations is considered. This problem requires the solution of an integral equation relating the values of the potential on the surface of the body to the values of the normal derivative, which is known from the small perturbation boundary conditions. The surface of the body is divided into small (hyperboloidal quadrilateral) surface elements, sigma sub i, which are described in terms of the Cartesian components of the four corner points. The values of the potential (and its normal derivative) within each element is assumed to be constant and equal to its value at the centroid of the element, and this yields a set of linear algebraic equations. The coefficients of the equation are given by source and doublet integrals over the surface elements, sigma sub i. The results obtained using the above formulation are compared with existing analytical and experimental results.

Morino, L.↗

Experimental measurements of the rotating frequencies and mode shapes of a full scale helicopter rotor in a vacuum and correlations with calculated results

This paper presents results of an experimental program conducted to obtain data which can be used for correlations of rotor blade dynamic analyses. Measurements were made of the rotating frequencies and mode shapes of a representative full-scale, two-bladed helicopter rotor in a vacuum. The blades were cantilevered to the hub. Mode shape data were obtained optically using a system of cameras developed specifically for this purpose. Excitation of the rotor was provided by vertical oscillatory motion of the hub. To compare experimental and analytical results, correlations of some experimental measurements with calculations from an existing blade modes computer program based on a Holzer-Myklestad procedure are presented, and the differences between the results are discussed. The experimental and analytical natural frequencies were generally in good agreement as were the principal components of the modal deflections for the flap and lag modes. The torsion mode shape indicated disagreement between the measured and calculated results in regard to the amount of flap and lag motions present in this mode, while the spanwise variations of the measured and calculated torsional components were in agreement.

Lee, B. L.↗

The Static and Dynamic Rotary Stability Derivatives at Subsonic Speeds of an Airplane Model Having Wing and Tail Surfaces Swept Back 45 degrees

Wind-tunnel measurements were made of the static and dynamic rotary stability derivatives of an airplane model having sweptback wing and tail surfaces. The Mach number range of the tests was from 0.23 to 0.94. The components of the model were tested in various combinations so that the separate contribution to the stability derivatives of the component parts and the interference effects could be determined. Estimates of the dynamic rotary derivatives based on some of the simpler existing procedures which utilize static force data were found to be in reasonable agreement with the experimental results at low angles of attack. The results of the static and dynamic measurements were used to compute the short-period oscillatory characteristics of an airplane geometrically similar to the test model. The results of these calculations are compared with military flying qualities requirements.

Lopez, Armando E.↗

Fluid Physics in a Fluctuating Acceleration Environment

Our program of research aims at developing a stochastic description of the residual acceleration field onboard spacecraft (g-jitter) to describe in quantitative detail its effect on fluid motion. Our main premise is that such a statistical description is necessary in those cases in which the characteristic time scales of the process under investigation are long compared with the correlation time of g-jitter. Although a clear separation between time scales makes this approach feasible, there remain several difficulties of practical nature: (i), g-jitter time series are not statistically stationary but rather show definite dependences on factors such as active or rest crew periods; (ii), it is very difficult to extract reliably the low frequency range of the power spectrum of the acceleration field. This range controls the magnitude of diffusive processes; and (iii), models used to date are Gaussian, but there is evidence that large amplitude disturbances occur much more frequently than a Gaussian distribution would predict. The lack of stationarity does not constitute a severe limitation in practice, since the intensity of the stochastic components changes very slowly during space missions (perhaps over times of the order of hours). A separate analysis of large amplitude disturbances has not been undertaken yet, but it does not seem difficult a priori to devise models that may describe this range better than a Gaussian distribution. The effect of low frequency components, on the other hand, is more difficult to ascertain, partly due to the difficulty associated with measuring them, and partly because they may be indistinguishable from slowly changing averages. This latter effect is further complicated by the lack of statistical stationarity of the time series. Recent work has focused on the effect of stochastic modulation on the onset of oscillatory instabilities as an example of resonant interaction between the driving acceleration and normal modes of the system, and on cavity flow as an example of how an oscillatory response under periodic driving becomes diffusive if the forcing is random instead. This paper describes three different topics that illustrate behavior that is peculiar to a stochastic acceleration field. In the first case, we show that g-jitter can induce effective attractive or repulsive forces between a pair of spherical particles that are suspended in an incompressible fluid of different density provided that the momentum diffusion length is larger than the interparticle separation (as in the case in most colloidal suspensions). Second, a stochastic modulation of the control parameter in the vicinity of a pitchfork or supercritical bifurcation is known not to affect the location of the threshold. We show, however, that resonance between the modulation and linearly stable modes close to onset can lead to a shift in threshold. Finally, we discuss the classical problem of vorticity diffusion away from a plane boundary that is being vibrated along its own plane. Periodic motion with zero average vorticity production results in an exponential decay of the vorticity away from the boundary. Random vibration, on the other hand, results in power law decay away from the boundary even if vorticity production averages to zero.

Drolet, Francois↗

Exit flow from a transonic compressor rotor

The three dimensional unsteady flow field behind a transonic compressor rotor with a design pressure ratio of 1.6 at a tip Mach number of 1.2 has been resolved on the blade passing time scale. Quantities determined were total and static pressures, tangential flow angle, and radial flow angle. The spatial and temporal resolution achieved was sufficient to determine velocity components inside individual blade wakes and in the surrounding flow. From these measurements the flow structure is described at stations immediately behind the rotor and one chord downstream. Some dominant features of the flow just behind the rotor are large radial velocity components, large static pressure fluctuations near the blade wakes, and definite unsteadiness (in rotor coordinates) of the wakes. The wake behavior one chord downstream is described in terms of the effect of the strong mean swirl on the behavior of shear disturbances. In the outer portion of the annulus, where the mean flow approximates a solid body rotation, a strong, persistent oscillatory flow is found with 16 periods in the circumference as roughly predicted by theory. In the inner portion of the annulus the disturbances attenuate axially.

Thompkins, W. T., Jr.↗

Two-component modeling of the solar IR CO lines

One-dimensional hydrostatic models of quiet and active solar regions can be constructed that generally account for the observed intensities of lines and continue throughout the spectrum, except for the infrared CO lines. There is an apparent conflict between: (1) observations of the strongest infrared CO lines formed in LTE at low-chromospheric heights but at temperatures much cooler than the average chromospheric values; and (2) observations of Ca II, UV (ultraviolet), and microwave intensities that originate from the same chromospheric heights but at the much higher temperatures characteristic of the average chromosphere. A model M(sub CO) has been constructed which gives a good fit to the full range of mean CO line profiles (averaged over the central area of the solar disk and over time) but this model conflicts with other observations of average quiet regions. A model L(sub CO) which is approximately 100 K cooler than M(sub CO) combined with a very bright network model F in the proportions 0.6 L(sub CO) + 0.4 F is found to be generally consistent with the CO, Ca II, UV, and microwave observations. Ayres, Testerman, and Brault found that models COOLC and FLUXT in the proportions 0.925 and 0.075 account for the CO and Ca II lines, but these combined models give an average UV intensity at 140 nm about 20 times larger than observed. The 0.6 L(sub CO) + 0.4 F result may give a better description of the cool and hot components that produce the space- and time-averaged spectra. Recent observations carried out by Uitenbroek, Noyes, and Rabine with high spatial and temporal resolution indicate that the faintest intensities in the strong CO lines measured at given locations usually become much brighter within 1 to 3 minutes. The cool regions thus seem to be mostly the low-temperature portions of oscillatory waves rather than cool structures that are stationary.

Avrett, Eugene H.↗

Some observations on the oscillatory behavior of carbon monoxide oxidation

The oscillatory behavior of the oxidation of carbon monoxide was experimentally studied in an attempt to further elucidate the reaction at low pressure. The phenomenon is observed as multiple explosions and involves successive flashes of light accompanying the slow reaction in a static system, including over 450 flashes in one case. Electronically excited hydroxyl radicals (water impurity) and carbon dioxide have been identified as components of the emission. The phase difference between the two was seen to be negligible. The nature of the temperature and pressure changes during a cycle indicates that the oscillation is purely kinetic rather than thermokinetic. A procedure is presented whereby sustained oscillations can be obtained for particular regions in the pressure-temperature plane, vessel surface pretreatments, and H2O-containing reactants.

Mccaffrey, B. J.↗