Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nb”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Processing and properties of PSZT 95/5 ceramics with varying Ti and Nb substitution

Niobium doped lead-tin-zirconate-titanate ceramics near the PZT 95/5 orthorhombic AFE – rhombohedral FE morphotropic phase boundary Pb 1-0.5y (Zr 0.865-x Ti x Sn 0.135 ) 1-y Nb y O 3 were prepared according to a 2 2+1 factorial design with x = 0.05, 0.07 and y = 0.0155, 0.0195. The ceramics were prepared by a traditional solid-state synthesis route and sintered to near full density at 1250°C for 6 hours. All compositions were ~98% dense with no detectable secondary phases by XRD. The ceramics exhibited equiaxed grains with intergranular porosity and grain size was ~5 μm, decreasing with niobium substitution. Compositions exhibited remnant polarization values of ~32 μC/cm 2 , increasing with Ti substitution. Depolarization by the hydrostatic pressure induced FE-AFE phase transition was drastically affected by variation of the Ti and Nb substitution, increasing at a rate of 113 MPa / 1% Ti and 21 MPa / 1% Nb. Total depolarization output was insensitive to the change in Ti and Nb substitution, ~32.8 μC/cm 2 for the PSZT ceramics. The R3c-R3m and R3m-Pm3m phase transition temperatures on heating ranged from 90 to 105°C and 183 to 191°C, respectively. Ti substitution stabilized the R3c and R3m phases to higher temperatures, while Nb substitution stabilized the Pm3m phase to lower temperatures. Thermal hysteresis of the phase transitions was also observed in the ceramics, with transition temperature on cooling being as much as 10°C lower.

36 MATERIALS SCIENCE↗
DOE OSTI2023

In-situ high energy X-ray diffraction study of deformation behavior in Nb nanoparticle-martensitic NiTi composite wire

Here, this study investigated the deformation behavior in Nb nanoparticle-martensitic NiTi composite wire during tensile loading by means of in-situ high-energy X-ray diffraction. Compared to Nb nanowires, the dispersedly distributed Nb nanoparticles have little effect on the transformation and deformation behaviors of NiTi matrix, causing the absence of R phase transformation and the occurrence of deformation twinning in NiTi matrix. Meanwhile, the occurrence of deformation twinning in NiTi matrix can reduce the shape strain to be coordinated by the unfavorable orientated martensite variants, and thus decreases the internal stress among NiTi martensite variants generated during martensite reorientation process. In addition, TEM result proved that Nb nanoparticles can achieve exceptionally large elastic strain in B19'-NiTi matrix (~4%), just as Nb nanowires. However, this large elastic strain (stress) will be released with the occurrence of NiTi deformation twinning.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of pinholes in Nb 4 C 3 MXene sheets on its electrochemical behavior in aqueous electrolytes

Two-dimensional (2D) niobium carbide, Nb 4 C 3 T x (T x : O, OH, and F), a representative member of the 43 MXene structural motif, has shown promising electrochemical performance in acidic electrolytes. The capacitive performance of Nb 4 C 3 T x in neutral aqueous electrolytes has been reported as moderate, but little effort has been made to improve it. In this paper, we report a method to introduce nanopores (pinholes) in Nb 4 C 3 T x MXene flakes by adjusting the etching time. The pinholes generated during the etching process improve ion diffusion pathways, which are otherwise hindered by the restacking of the 2D flakes. The “holey Nb 4 C 3 T x ” shows a 50 % improved rate capability at charge/discharge time scales of 1–2 s in 1 M Li 2 SO 4 , Na 2 SO 4 , and (NH 4 ) 2 SO 4 electrolytes. Our strategy of controlling the permeability of Nb 4 C 3 T x sheets can potentially be applied to other MXenes, providing guidance for improving the capacitance and rate capability of 2D materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Dirac Nodal Line in Hourglass Semimetal Nb 3 SiTe 6

Glide-mirror symmetry in nonsymmorphic crystals can foster the emergence of novel hourglass nodal loop states. Here, we present spectroscopic signatures from angle-resolved photoemission of a predicted topological hourglass semimetal phase in Nb 3 SiTe 6 . Linear band crossings are observed at the zone boundary of Nb 3 SiTe 6 , which could be the origin of the nontrivial Berry phase and are consistent with a predicted glide quantum spin Hall effect; such linear band crossings connect to form a nodal loop. Furthermore, the saddle-like Fermi surface of Nb 3 SiTe 6 observed in our results helps unveil linear band crossings that could be missed. Additionally, in situ alkali-metal doping of Nb 3 SiTe 6 also facilitated the observation of other band crossings and parabolic bands at the zone center correlated with accidental nodal loop states. Overall, our results complete the system's band structure, help explain prior Hall measurements, and suggest the existence of a nodal loop at the zone center of Nb 3 SiTe 6 .

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Properties of Nb x Ti (1–x) N thin films deposited on 300 mm silicon wafers for upscaling superconducting digital circuits

Scaling superconducting digital circuits requires fundamental changes in the current material set and fabrication process. The transition to 300 mm wafers and the implementation of advanced lithography are instrumental in facilitating mature CMOS processes, ensuring uniformity, and optimizing the yield. Here, this study explores the properties of Nb x Ti (1–x) N films fabricated by magnetron DC sputtering on 300 mm Si wafers. As a promising alternative to traditional Nb in device manufacturing, Nb x Ti (1–x) N offers numerous advantages, including enhanced stability and scalability to smaller dimensions, in both processing and design. As a ternary material, Nb x Ti (1–x) N allows engineering material parameters by changing deposition conditions. The engineered properties can be used to modulate device parameters through the stack and mitigate failure modes. We report characterization of Nb x Ti (1–x) N films at less than 2% thickness variability, 2.4% T c variability and 3% composition variability. Film resistivity (140–375 Ωcm) shows a strong correlation with the film oxygen content, while the critical temperature T c (4.6 K–14.1 K) is strongly affected by film stoichiometry and its microstructure has only a moderate effect on modifying T c . Our results offer insights about the interplay between film stoichiometry, film microstructure and critical temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Demonstration of $E$ acc = 10 MV m −1 with Nb 3 Sn cavities in a cryomodule

Accelerating cryomodules with superconducting cavities are key components for particle accelerators. The efficiency, energy gain and operating temperature of cavities drive the operating and capital costs; hence, advances in these areas enable future accelerators. While superconducting cavities are currently made from Nb, Nb 3 Sn, with a superconducting transition temperature and superheating field approximately twice that of Nb, is poised to substantially improve the efficiency and energy gain. We present results from the first cryomodule with two five-cell 1.5 GHz superconducting radiofrequency Nb cavities coated with Nb 3 Sn, which attained an accelerating gradient of ⩾10 MV m −1 with low cryogenic loss at 4.4 K.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Investigation of structural and thermal properties of Nb 2 CT X MXenes at elevated temperature

Nb-based MXenes, particularly Nb 2 CT X is noted for its metallic characteristics, and nearly zero band gap because of it 2D structure. Different synthesis processes have been utilized such as HF etching, HCl/LiF and molten salt method to prepare delaminated Nb 2 CT X MXene sheets[1]. Moreover, various approaches have been tried for modifying MXenes properties including partial oxidation for application such as energy storage, gas sensing, photocatalyst etc. One step synthesis technique used for creating efficient hydrogen evolution photocatalyst comprised of Nb 2 O 5 /C/Nb 2 C composites. Furthermore, we have prepared Nb 2 CT X MXenes with a strong etching method and investigated its fundamental properties at elevated temperature.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Ground-state and decay properties of neutron-rich 106 Nb

The ground-state properties of neutron-rich 106 Nb and its β decay into 106 Mo have been studied using the CARIBU radioactive-ion-beam facility at Argonne National Laboratory. Niobium-106 ions were extracted from a 252 Cf fission source and mass separated before being delivered as low-energy beams to the Canadian Penning Trap, as well as the X-Array and SATURN β-decay-spectroscopy station. The measured 106 Nb ground-state mass excess of –66202.0(13) keV is consistent with a recent measurement but has three times better precision; this work also rules out the existence of a second long-lived, β-decaying state in 106 Nb above 5 keV in excitation energy. The decay half-life of 106 Nb was measured to be 1.097(21) s, which is 8% longer than the adopted value. Here, the level scheme of the decay progeny, 106 Mo, has been expanded up to ≈ 4 MeV. The distribution of decay strength and considerable population of excited states in 106 Mo of J ≥ 3 emphasizes the need to revise the adopted J π = 1 – ground-state spin-parity assignment of 106 Nb; it is more likely to be J ≥ 3.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Additive manufacturing of high-strength multiphase nanostructures in the binary Ni–Nb system for the discovery of new types of superalloys

Abstract Ni-based superalloys have been studied extensively due to their impressive mechanical properties, including strength and creep resistance at high temperatures. Growing interest surrounding additive manufacturing (AM) methods has led to recent investigations of alloys that are traditionally difficult to process, including Ni-based superalloys. Recent work has shown that AM methods enable high-throughput materials discovery and optimization of difficult- or impractical-to-process alloys, including those with high or even majority refractory element compositions. This work focuses on AM-enabled investigations of composition-dependent mechanical and microstructural properties for Ni–Nb binary alloys. Specifically, we report on the mechanical behavior of compositionally-graded Ni x Nb 1− x and uniform composition Ni 59.5 Nb 40.5 specimens made with AM. The AM fabrication process resulted in extraordinarily high strength, attributed to the formation of a dual-phase microstructure consisting of δ-Ni 3 Nb and µ-Ni 6 Nb 7 intermetallic compounds with nanostructured and multimodal grain size and eutectic lamellar spacing. Graphic Abstract

Jones, M. R.↗
DOE OSTI2022

Microstructure Changes Observed in the Near-Surface Region of SRF Nb Cavities Cutouts upon Cooling/Heating Cycles Using GI-Synchrotron XRD

We have mapped microstructural changes in the near-surface region of Nb from SRF cavity-cutouts upon thermal cycles in the range from 300 to 30 K using grazing incidence synchrotron X-Ray diffraction (GIXRD). Segregation of secondary phases was observed after the thermal cycle, and their nature has been clarified and discussed in view of previous studies on hydrides formation in SRF bulk Nb cavities. The temperature dependence of the relative population of these formed phases was obtained from GIXRD patterns profile fitting. Both, Nb bulk matrix and the new phases formed after cool-down show specific structural features as thermal contraction/expansion, structural transitions, and Nb lattice variation due to the induced strain by precipitates formation. The information derived from this structural study can explain some phenomena as the dissipation at high accelerating field (i.e. High Field Q Slope, HFQS) in the Nb SRF performance as well as new mechanisms never addressed in previous studies.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Managing Sn-Supply to Tune Surface Characteristics of Vapor-Diffusion Coating of Nb₃Sn

Nb₃Sn promises better RF performance (Q and E_{acc}) than niobium at any given temperature because of superior superconducting properties. Nb₃Sn-coated SRF cavities are now produced routinely by growing a few microns thick Nb₃Sn films inside Nb cavities via the tin vapor diffusion technique. Sn evaporation and consumption during the growth process notably affect the quality of the coating. Aiming at favorable surface characteristics that could enhance the RF performance, many coatings were produced by varying Sn sources and temperature profiles. Coupon samples were examined using different material characterization techniques, and a selected few sets of coating parameters were used to coat 1.3 GHz single-cell cavities for RF testing. The Sn supply’s careful tuning is essential to manage the microstructure, roughness, and overall surface characteristics of the coating. We summarize the material analysis of witness samples and discuss the performance of several Nb₃Sn-coated single-cell cavities linked to Sn-source characteristics and observed Sn consumption during the film growth process.

Pudasaini, U.↗
DOE OSTI2023

Microstructure development in a cold worked SRF Nb sheet undergoing 700°C-900°C/3h heat treatments.

Bulk Nb for TESLA shaped SRF cavities is a mature technology, with high gradient (>35 MV/m) and high Q cavities (>1010, ~2K) routinely fabricated. Significant advances are in order to push Q?s to 1011 (~2K), and involve modifications to the sub-surface Nb layers by impurity doping (N, O). In order to achieve the lowest surface resistance any trapped flux needs to be expelled for cavities to reach high Q?s. There is clear evidence that cavities fabricated from polycrystalline sheets meeting current specifications require higher temperatures beyond 800oC leads to better flux expulsion, and hence improves Q. Recently, cavities fabricated with a non-traditional Nb sheet with initial cold work due to cold rolling expelled flux better after 800°C/3h heat treatment than cavities fabricated using fine-grain polycrystalline Nb sheets. Here, we analyze the microstructure development in Nb from the vendor supplied cold work non-annealed sheet that was fabricated into an SRF cavity as a function of heat treatment building upon the methodology development to analyze microstructure being developed by the FSU-MSU-UT-Austin- JLAB collaboration. The results indicate correlation between full recrystallization and better flux expulsion.

Balachandran, S.↗
NASA NTRS1989

Precipitation strengthened high strength, high conductivity Cu-Cr-Nb alloys produced by chill block melt spinning

A series of Cu-based alloys containing 2 to 10 a/o Cr and 1 to 5 a/o Nb were produced by chill block melt spinning (CBMS). The melt spun ribbons were consolidated and hot rolled to sheet to produce a supersaturated Cu-Cr-Nb solid solution from which the high melting point intermetallic compound Cr2Nb could be precipitated to strengthen the Cu matrix. The results show that the materials possess electrical conductivities in excess of 90 percent that of pure Cu at 200 C and above. The strengths of the Cu-Cr-Nb alloys were much greater than Cu, Cu-0.6 Cr, NARloy-A, and NARloy-Z in the as-melt spun condition. The strengths of the consolidated materials were less than Cu-Cr and Cu-Cr-Zr below 500 C and 600 C respectively, but were significantly better above these temperatures. The strengths of the consolidated materials were greater than NARloy-Z, at all temperatures. The GLIDCOP possessed similar strength levels up to 750 C when the strength of the Cu-Cr-Nb alloys begins to degrade. The long term stability of the Cu-Cr-Nb alloys was measured by the microhardness of aged samples and the growth of precipitates. The microhardness measurements indicate that the alloys overage rapidly, but do not suffer much loss in strength between 10 and 100 hours which confirms the results of the electrical resistivity measurements taken during the aging of the alloys at 500 C. The loss in strength from peak strength levels is significant, but the strength remains exceptionally good. Transmission electron microscopy (TEM) of the as-melt spun samples revealed that Cr2Nb precipitates formed in the liquid Cu during the chill block melt spinning, indicating a very strong driving force for the formation of the precipitates. The TEM of the aged and consolidated materials indicates that the precipitates coarsen considerably, but remain in the submicron range.

Ellis, David L.↗
NASA NTRS1993

Effects of processing and prolonged high temperature exposure on the microstructure of Nb-1Zr-C sheet

High temperature stability of the microstructure of Nb-1Zr sheet containing 0.1 and 0.06 wt. percent C was studied as affected by processing and prolonged 1350 K exposure with and without applied stress. Sheets were fabricated by cold rolling bars that were single-, double-, or triple-extruded at 1900 K. Creep samples were double-annealed (1 h at 1755 K + 2 h at 1475 K) prior to testing at 1350 K and 10,000 - 34,500 h. The microstructures of the as-cast, extruded, rolled, DA, and crept samples were characterized using various metallographic and analytical methods. The precipitates were rather coarse Nb2C initially, but transformed to finer (less than or equal to 1 micron) carbides of (Zr, Nb)C with each subsequent high temperature process. The grain size, and the relative amount and morphology of (Zr, Nb)C were found to be affected by the number of extrusions and to some extent by C-content. However, the microstructures of all the crept samples were similar with (Zr, Nb)C distributed throughout the matrix indicating that prolonged exposure to 1350 K gave rise to complete transformation of Nb2C to (Zr, Nb)C regardless of the processing history. These and other observations are presented with the emphasis on the correlation between processing, microstructure, and creep properties.

Uz, Mehmet↗
NASA NTRS2008

Nb(x)Ti(1-x)N Superconducting-Nanowire Single-Photon Detectors

Superconducting-nanowire single-photon detectors (SNSPDs) in which Nb(x)Ti(1-x)N (where x<1) films serve as the superconducting materials have shown promise as superior alternatives to previously developed SNSPDs in which NbN films serve as the superconducting materials. SNSPDs have potential utility in optical communications and quantum cryptography. Nb(x)Ti(1-x)N is a solid solution of NbN and TiN, and has many properties similar to those of NbN. It has been found to be generally easier to stabilize Nb(x)Ti(1-x)N in the high-superconducting-transition temperature phase than it is to so stabilize NbN. In addition, the resistivity and penetration depth of polycrystalline films of Nb(x)Ti(1-x)N have been found to be much smaller than those of films of NbN. These differences have been hypothesized to be attributable to better coupling at grain boundaries within Nb(x)Ti(1-x)N films.

Stern, Jeffrey A.↗
DOE OSTI2021

What is the Role of Nb in Nickel-Rich Layered Oxide Cathodes for Lithium-Ion Batteries?

Nickel-rich layered metal oxide LiNi 1–y–z Mn y Co z O 2 (1 – y – z ≥ 0.8) materials are the most promising cathodes for next-generation lithium-ion batteries in electric vehicles. However, they lose more than 10% of their capacity on the first cycle, and interfacial/structural instability causes capacity fading. Coating and substitution are possible direct and effective solutions to solve these challenges. In this Letter, Nb coating and Nb substitution on LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) is easily produced through a scalable wet chemistry method followed by sintering from 400 to 800 °C. A Li-free Nb oxide treatment is found to remove surface impurities forming a LiNbO 3 /Li 3 NbO 4 surface coating, to reduce the first capacity loss and to improve the rate performance. Furthermore, Nb substitution stabilizes the structure, as evidenced by less heat evolution on heating, thus providing better long cycling stability with a 93.2% capacity retention after 250 cycles.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Materials Data on Nb(Te2I3)2 by Materials Project

Nb(TeI3)2(Te)2 crystallizes in the triclinic P-1 space group. The structure is zero-dimensional and consists of four tellurium molecules and two Nb(TeI3)2 clusters. In each Nb(TeI3)2 cluster, Nb2+ is bonded in an L-shaped geometry to two I1- atoms. There are one shorter (2.99 Å) and one longer (3.00 Å) Nb–I bond lengths. There are two inequivalent Te1+ sites. In the first Te1+ site, Te1+ is bonded in a rectangular see-saw-like geometry to four I1- atoms. There are a spread of Te–I bond distances ranging from 2.81–3.20 Å. In the second Te1+ site, Te1+ is bonded in a rectangular see-saw-like geometry to four I1- atoms. There are a spread of Te–I bond distances ranging from 2.81–3.18 Å. There are six inequivalent I1- sites. In the first I1- site, I1- is bonded in a 3-coordinate geometry to one Nb2+ and two Te1+ atoms. In the second I1- site, I1- is bonded in a single-bond geometry to one Te1+ atom. In the third I1- site, I1- is bonded in a single-bond geometry to one Te1+ atom. In the fourth I1- site, I1- is bonded in a single-bond geometry to one Te1+ atom. In the fifth I1- site, I1- is bonded in a single-bond geometry to one Te1+ atom. In the sixth I1- site, I1- is bonded in a 3-coordinate geometry to one Nb2+ and two Te1+ atoms.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Materials Data on Nb(SeI)2 by Materials Project

Nb(SeI)2 crystallizes in the monoclinic C2/m space group. The structure is two-dimensional and consists of one Nb(SeI)2 sheet oriented in the (0, 0, 1) direction. Nb5+ is bonded in a 8-coordinate geometry to four Se+1.50- and four equivalent I1- atoms. There are two shorter (2.64 Å) and two longer (2.66 Å) Nb–Se bond lengths. There are two shorter (3.00 Å) and two longer (3.01 Å) Nb–I bond lengths. There are two inequivalent Se+1.50- sites. In the first Se+1.50- site, Se+1.50- is bonded in a 2-coordinate geometry to two equivalent Nb5+ atoms. In the second Se+1.50- site, Se+1.50- is bonded in a 2-coordinate geometry to two equivalent Nb5+ atoms. I1- is bonded in a distorted water-like geometry to two equivalent Nb5+ atoms.

36 MATERIALS SCIENCE↗