Results for “Multiphysics” — Page 7

NASA NTRS2023

Coupled Fluid Dynamics and Material Response Simulations for Nitrogen High Enthalpy Flows

The study focuses on the interaction of nitrogen flows with thermal protection systems during atmospheric re-entry for NASA flight missions. The Ares multiphysics coupling tool is employed to investigate the coupling between the fluid (US3D) and material response (Icarus) solvers using various modeling approaches. These approaches include the equilibrium thin-film coefficients approach, a weakly coupled approach with temperature coupling, and an approach considering the full chemical composition of the surface and the transfer of pyrolysis gases. The objective is to understand and accurately represent the mechanisms of nitrogen interaction with the surface, such as nitridation and catalytic recombination. The study aims to assess the accuracy of the different approaches by comparing them to experimental results obtained from NASA arc-jet facilities. By addressing these challenges and improving the understanding of nitrogen-surface interactions, it is expected to enhance the design and performance analysis of thermal protection systems for future missions.

Ablation↗

NASA NTRSDate not supplied

Silver Electrolysis for Disinfection of Spacecraft Potable Water: 2023 Update

Anodic dissolution of silver electrodes, or “silver electrolysis,” is being investigated as a means of introducing biocidal silver into potable water on exploration spacecraft. Last year’s paper reported a fault condition termed “electrode bridging,” in which silver deposits on interelectrode wetted materials, eventually bridging the electrode gap and providing an alternate conduction pathway that diminishes the silver output of the reactor. Since then, two strategies have been developed that prevent this fault from occurring: 1) increasing the frequency of polarity reversal and 2) separating the active surface of the electrode from the interelectrode wetted material. These strategies were tested independently, and in both cases, the reactor performed as expected with no occurrence of bridging for at least one crew-year equivalent of cumulative operation. Additional tests were conducted at varying levels of influent dissolved oxygen to better understand the nature of the cathode reaction and its impact on reactor performance. Results indicate that the primary cathode reaction is the reduction of dissolved oxygen, which could imply a dependence of reactor performance on dissolved oxygen concentration. However, it was found that at the typical oxygen concentrations anticipated for spacecraft processed water, the impact on silver electrolysis performance was negligible. Finally, multiphysics modelling of the reactor fluid mechanics and electrochemistry was undertaken to provide the capability to optimize the design of a future reactor prototype.

silver electrolysis↗

NASA NTRS2023

Analytical Design and Performance Estimation Methods for Aircraft Permanent Magnet Synchronous Machines

The design of an electric motor drivetrain is a complex multiphysics problem. Low fidelity motor drivetrain sizing can be a key tool in the design cycle of an electric motor drivetrain and for system level studies of aircraft configurations. However, low fidelity sizing can lead to misleading results if all the physics involved in a motor design are not properly accounted for. This paper provides details on modeling approaches for initial design and sizing of permanent magnet synchronous electric machines. The goal of this paper is to provide the reader an understanding of the key principles of motor design and some modeling approaches to perform initial sizing of an electric motor and its inverter.

Thomas F. Tallerico↗

NASA NTRS2023

Oxidation of Silicon Particles Suspended in Mullite Matrix With Dual-Mode Vacancy Diffusion of Oxygen

Mullite bond coats filled with silicon particles have recently been proposed for the next generation of environmental barrier coatings (EBCs). The sacrificial oxidation of the silicon particles eliminates some of the environmental durability issues associated with traditional EBC designs. To investigate this novel design approach, a mathematical formulation and resulting numerical method have been developed for simulating the oxidation of silicon particles embedded in a mullite matrix. The focus is on the oxidation of the silicon in a dry oxygen environment where the oxidant is presumably oxygen. Oxygen transport from the exterior environment through the mullite is assumed to occur via two lattice defect diffusion mechanisms. As a result, the rate of oxygen transport is dictated by the self-diffusivity of the lattice defects. The numerical method is implemented using the COMSOL Multiphysics® program (COMSOL, Inc.). The method is applied to simulate the oxidation of silicon particles in a mullite pellet in recent oxidation experiments. Numerical results compare favorably with the oxidation behavior observed in the oxidation experiments. The numerical method is also used to investigate the effects of various features of the mullite-silicon particle system on the oxidation behavior.

silicon oxidation↗

NASA NTRSDate not supplied

Optimizing the Electroforming Process to Enhance the Thickness Uniformity of Full Shell X-Ray Optics

Electroforming replication technology at Marshall Space Flight Center has a long heritage of producing highquality full-shell X-ray mirrors for various applications. Nickel alloys are electroformed onto a super-polished mandrel in the electroforming process, then separated to form the replicated full-shell optic. Various parameters in the electroplating configuration could result in the nonuniformity of the shell’s thickness. Thickness nonuniformities primarily occur due to non-uniform electric field distributions in the electroforming tank during the deposition. Using COMSOL Multiphysics simulations, we have studied the electric field distributions during the deposition process. Using these studies, we have optimized the electric fields inside the tank using customized shields and insulating gaskets on the mandrel. These efforts reduced thickness non-uniformity from over 20% to under 5% percent. Improving the thickness uniformity of the shell aids in better mounting and alignment of shells in the optics module. Optimization of the electroforming process, in some cases, improved the optical performance of the shells. COMSOL optimizing of the electroforming process and the experimental results validating these simulations are presented in this article.

X-ray optics↗

NASA NTRS2023

CESO 22-3: Simulated Excavation Environment for Lunar Operations Follow-on

As more lunar In-Situ Resource Utilization (ISRU) missions are planned and developed, a need was identified for a simulation environment with accurate regolith interaction mechanics that is less computationally expensive than commercially available multiphysics tools. The purpose of the Simulated Excavation Environment for Lunar Operations (SEELO) project was to develop an interactive simulation environment that efficiently models lunar ISRU excavation operations, including soil deformation, while running in faster-than-real-time.

Michael DuPuis↗

NASA NTRSDate not supplied

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗

NASA NTRSDate not supplied

Particle Impact Simulation and Ignition Prediction

An experimentally calibrated tool is needed to predict if a system is susceptible to failure by particle impact ignition (PI) based on use conditions, materials, and flow geometry. This tool will accelerate new components, evaluating existing hardware, and help disposition anomalies. Conduct particle impact testing with in-situ diagnostics and complementary simulations on subset of key engineering materials (IN718, M400, 316L, 6061, Ti64, Zr) to develop a proof-of-concept predictive tool for assessing the risk of PI for idealized geometries (spherical particles) in realistic environments. Assess particle/target interactions (coefficient of restitution, ignition, kindling) using instrumented particle impact rigs while systematically varying key parameters (materials, particle size, environment, target configuration). Determine key field variables (temperature, strain, stress) in particle impacts using Multiphysics finite element and hydrocode simulations validated through comparison with experimental measurements and observations. Synthesize experiments and simulations into constitutive models for PI that can be integrated with existing computational fluid dynamics (CFD) and Debris Transport Analysis (DTA) tools in future efforts

particle impact↗

NASA NTRSDate not supplied

Coupled Reactor and Engine Nuclear Thermal Propulsion Modeling Methodology

The design and development process of a Nuclear Thermal Propulsion (NTP) system requires extensive multiphysics modeling to couple the neutron physics and thermal feedback effects to determine the reactor’s power shape. Propulsion system performance codes utilize this power shape to determine NTP key performance parameters. While the power shape is heavily dependent on the temperature profile and geometry of the reactor, many analyses either assume a constant power shape, or use neutronics analysis to determine a power shape for a specific reactor configuration. The development of a coupling interface for a propulsion system performance code and a Monte Carlo neutron transport code (OpenMC) allows for the reactor power shape to be calculated in a Picard iteration.

Jacob Stonehill↗

NASA NTRSDate not supplied

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗

NASA NTRSDate not supplied

Comprehensive Digital Twin of a Macro-fluidic Electrochemical Reactor to Optimize the Electrochemical-based Recovery of O2 from Metabolic CO2

Future long-duration missions will require a sustainable and efficient system capable of yielding a minimum of 75% O 2 recovery from metabolic CO 2 to achieve self-sufficiency for long space missions beyond Earth's low orbit. A Macro-fluidic Electrochemical Reactor (MFECR) development effort to electrochemically recover O 2 from CO 2 is underway at NASA Marshall Space Flight Center (MSFC) to increase current O 2 recovery efficiency and reduce air revitalization (AR) system complexity at the International Space Station (ISS) habitat and future long missions. The authors have developed and deployed a digital twin of an actual single cell of the MFECR via a comprehensive 3D multiphysics model that thoroughly replicates the exact configuration and fluid/material domains of the MFECR. This model's electrochemical physics consists of multicomponent-multiphase electrochemical-driven reactions leading to CO 2 conversion to C 2 H 4 and CO along with the formation of H 2 on the cathode in parallel with the generation of O 2 and H 2 O on the anode. This electrochemical model is coupled with all the physics phenomena involved in the process, including but not limited to fluid and non-ideal mass transfer of reactant and product species in free and porous media, convective/conduction/radiative heat transfer, and conduction of DC electrical current with Joule heating generation. The digital twin has proved to be an essential tool for performing different qualitative studies, including the effect of reducing the height (increasing the respect ratio) of the serpentine walls, leading to a further redesign of the EDU (the newly redesigned MFECR EDU has been fabricated and is expected to be used in future tests), the evaluation of setting different MFECRs connected in series, and the assessment of feeding air directly to the MFECR skipping the preceding metabolic CO 2 separation from air. The MFECR's test stand is fully automated and equipped with several inline measurements (flow, pressure, temperature, pH, component concentration) systems on all six MFECR's IO streams, allowing reliable experimental validation of the model, parametric determination of all electrochemical reactions, and process optimization.

Jesus A Dominguez↗

NASA NTRSDate not supplied

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗

NASA NTRSDate not supplied

Silver Electrolysis for Disinfection of Spacecraft Potable Water: 2024 Update

Anodic dissolution of silver electrodes, or “silver electrolysis,” is being investigated as a means of introducing biocidal silver into potable water on exploration spacecraft. This paper provides an update on the effort to implement this technology into a spacecraft potable water system. Previous papers reported on the feasibility of the technology for this application, strategies to prevent a potential fault condition termed “electrode bridging,” results from a preliminary investigation into the cathode reaction, and preliminary multiphysics modeling of the reactor. Since then, work has begun on the design of a next-generation silver electrolysis reactor prototype that will incorporate improvements identified in previous testing and package the reactor in a more flight-like configuration. This development effort has included additional testing to optimize the reactor design for prevention of electrode bridging, further investigation into the cathode reaction (including the use of a dissolved hydrogen sensor), and an assessment of the feasibility of using the reactor in other applications, such as for microbial shock and preparation for system dormancy.

silver biocide↗

NASA NTRS2024

University of South Alabama: Evaluation of Using Heat Pipes to Cool Adsorbent Beds in AC-TSAC Systems

This report details the results of the research and work of undergraduate students at the University of South Alabama across the 2023-24 academic year. These results examine the use of heat pipes for air revitalization in space exploration and habitation units. The current mechanism for removing carbon dioxide in the International Space Station is the Carbon Dioxide Removal Assembly (CDRA), which involves 2 cooperating adsorbent beds that continuously adsorb and desorb carbon dioxide. Recently, NASA has investigated the use of air-cooled temperature swing adsorption compressors (AC-TSAC) to provide both adsorption and compression of CO 2 . To effectively adsorb and desorb CO 2 , the beds must operate across a range of temperatures and require efficient heating and cooling to reach the necessary operating temperatures. Heat pipes, which are fluid-filled rods that use a wicking mechanism to transfer heat, may provide one alternative approach to moving heat into and out of adsorption beds. To test the cooling efficiency of packed beds equipped with heat pipes, a packed bed was constructed to examine the amount of heat transferred with this technology. In addition to a physical apparatus, a model was built using COMSOL Multiphysics® to obtain an initial assessment of the effectiveness of using heat pipes for temperature control in porous adsorption beds.

T. Grant Glover↗

NASA NTRSDate not supplied

Modeling of a Solid Oxide Fuel Cell as Part of a Predictive Functional Model for Aerospace Fuel-Cell Systems

This paper will discuss initial efforts at modeling a solid oxide fuel cell (SOFC) for aerospace applications. Fuel cells historically have been used in spacecraft from the Gemini to the Shuttle era for providing spacecraft power with the added benefit of producing water for crew use. However, there are many potential applications for fuel cells and electrolyzers in spaceflight, including oxygen generation, in-situ resource utilization (ISRU) and propellant production. This proof-of-concept model has been developed using a commercial multiphysics modeling software package. Two-dimensional and one-dimensional isothermal models were created based on a certain SOFC design and results were compared to test data from the real system. Local Butler-Volmer kinetic relations were adjusted, and an effective porous medium approach was taken in order to capture how the many interconnects between cells in the gas channels affected fluid flow. The model was able to reproduce polarization curves derived from test data within around 0.02 Volts for a given current density. This model could be adapted to model a solid oxide electrolyzer, proton exchange membrane fuel cell, or other type of fuel cell technology in order to understand how these types of technologies could fit into broader spacecraft designs and advance the capabilities of spaceflight systems.

Mary Lou Nadeau↗

NASA NTRSDate not supplied

Silver Electrolysis for Disinfection of Spacecraft Potable Water: 2024 Update

Anodic dissolution of silver electrodes, or “silver electrolysis,” is being investigated as a means of introducing biocidal silver into potable water on exploration spacecraft. This paper provides an update on the effort to implement this technology into a spacecraft potable water system. Previous papers reported on the feasibility of the technology for this application, strategies to prevent a potential fault condition termed “electrode bridging,” results from a preliminary investigation into the cathode reaction, and preliminary multiphysics modeling of the reactor. Since then, work has begun on the design of a next-generation silver electrolysis reactor prototype that will incorporate improvements identified in previous testing and package the reactor in a more flight-like configuration. This development effort has included additional testing to optimize the reactor design for prevention of electrode bridging, further investigation into the cathode reaction (including the use of a dissolved hydrogen sensor), and an assessment of the feasibility of using the reactor in other applications, such as for microbial shock and preparation for system dormancy.

silver biocide↗

NASA NTRSDate not supplied

System Modeling of a Lunar Molten Regolith Electrolysis Plant

Introduction: In-Situ Resource Utilization (ISRU) is the process of extracting local resources to produce commodities for propulsion, life support systems, and off-planet construction rather than transporting consumables from Earth. Molten Regolith Electrolysis (MRE) is a novel ISRU method of extracting oxygen gas and metal alloy from lunar regolith. The MRE process involves placing lunar regolith between two electrodes, through which current is passed, to melt the regolith and reduce the metal oxide constituents by direct electrolysis (e.g. FeO, SiO2, MgO, Al2O3) into oxygen gas and metal alloys. The oxygen is liquefied and used as propellant for landers, while the metals (e.g. Ferro-alloys) are further processed and used in structural building materials and parts manufacturing. A system model was developed that accounted for the major processes of an MRE plant (from excavation of raw materials to storage of products) to assess the feasibility of a lunar MRE plant. The System Engineering and Integration (SE&I) ISRU Modeling and Analysis (SIMA) team utilized its previously documented system sizing model, the Mission Analysis and Integration Tool (MAIT) [1] as framework of the system model. MAIT uses MATLAB/Simulink to integrate subsystem models into a complete system model of the MRE plant. Total mass, volume, and power requirements were computed for numerous iterations of a MRE plant. System Model: Figure 1: MRE Plant Block Diagram The regolith excavation model determines the mass and power needed to excavate sufficient regolith. The preheating auger initiates the regolith heating process before regolith enters the MRE re-actor to reduce the energy required to turn the solid into a molten liquid. The MRE reactor is modeled in COMSOL Multiphysics and based on the research by Dominguez, Sibille, and Schreiner [2, 3, 4]. This preliminary reactor model provides an accurate calculation of thermal equilibrium during electrochemical operation of the reactor system to assess the optimal mass and power required to process the inlet flow of regolith. The model also computes the outlet flowrates of oxygen and molten products. For this analysis, the primary components of the metal alloy considered were iron and silicon. The oxygen is then purified using an Yttrium Stabilized Zirconia (YSZ) electrode, followed by liquefaction using a 90K cryocooler to be stored as liquid oxygen in insulated cylindrical tanks. In future iterations of the system model, the molten metal tapped from the MRE reactor will undergo additional processing or refinement. However, downstream handling of metals is currently a technology gap that is missing a high TRL subsystem model. Therefore, for this analysis, the accumulated metal alloy stream terminates after leaving the MRE reactor. Study Goals: This analysis investigates multiple input variables to the system to determine the sensitivity of a (near) complete plant at full-scale. This preliminary investigation ran parametric sweeps on the MRE reactor geometry, electrical current supply, layers of multi-layer insulation (MLI) on the reactor, size of the electrodes in the oxygen purification model, and regolith composition (based on landing site location). Three production targets of oxygen (1,000, 10,000, and 50,000 kg/yr) were investigated for this analysis. The parametric sweeps conducted in this analysis provide valuable insight into the expected impact of the various model inputs on plant size. This information can be used to identify the most critical components of the plant and guide future decisions on allocating funding for research and development, providing subsystem developers with appropriate interfaces with downstream and upstream processes, and assessing the overall feasibility of MRE when compared to other ISRU plants. References: [1] Carlson, A. et al. (2024) ICES, ICES-2024-53. [2] Dominguez, D.A., and Sibille, L. (2011) AIAA, AIAA-2011-700. [3] Schreiner, S.S. (2015) MIT, Dissertation. [4] Schreiner, S.S. et al. (2016) ASR, 57(7), pp.1585-1603.

ISRU↗

NASA NTRSDate not supplied

Investigations of an Aeroelastic Optimization Benchmark Problem with MPhys and FUN3D

High-fidelity aeroelastic optimization capabilities are becoming more common in recent years. In this field, researchers typically present results on the design problems of greatest interest to them. The lack of consistency with respect to baseline configurations, design variables, objectives and constraints, etc., makes it difficult to compare approaches and creates an obstacle for the community to work together to advance the state of the art. The High-Fidelity Aeroelastic Optimization Benchmark Working Group has been established to create and study a series of benchmark aeroelastic optimization problems that the community can utilize to compare methods on the same optimization problem. This paper presents optimization results from NASA Langley Research Center for the first benchmark case of this series with analysis based on MPhys, a multiphysics library for OpenMDAO, and FUN3D, an unstructured computational fluid dynamics suite of tools. For the optimization case presented, it is demonstrated that a progression of increasing aerodynamic model fidelity reduces the wall time required to complete the optimization.

Aeroelasticity↗