SEARCH · Engineering Papers

Results for “Molten”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2023

Tribocorrosion of stainless steel sliding against graphite in FLiNaK molten salt

The molten salt reactor (MSR) concept recently gained renewed interest in developing Generation IV nuclear reactors. One MSR design uses fluoride molten salts to cool tri-structural isotropic particle fuel encapsulated by a carbon matrix into spherical pebbles, which would inevitably contact the reactor's stainless steel container wall during salt circulation. Characterizing this interaction is crucial for reactor safety. Here, in this work, we report the tribocorrosion behavior of graphite sliding against Type 316H stainless steel lubricated by a FLiNaK (LiF:NaF:KF; 46.5:11.5:42 mol %) molten salt in an argon environment. Accelerated wear loss was observed at a higher temperature because of a lower molten salt viscosity and a higher corrosion rate. The graphite had a more rapid material loss at a higher sliding speed than stainless steel because of its higher vulnerability to vibration-induced microfracture. The salt-starved condition caused more material loss than either the no-salt or the salt-flooded condition because neither a graphite transfer film nor stable boundary lubrication could be established at salt starvation. An interesting dual-layer surface film was discovered on the stainless steel worn surface: a chromium-rich top film and a nickel-accumulated but chromium-depleted interlayer. The film composition and structure provide fundamental insights to the mechanochemical interactions between stainless steel and graphite in a molten salt environment.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2021

Molten-salt-mediated carbon dioxide capture and superequilibrium utilization with ethane oxidative dehydrogenation

Existing CO 2 -mediated oxidative dehydrogenation (CO 2 -ODH) of ethane has yet to demonstrate >60% single-pass CO yield due to the intrinsic equilibrium limitations. We report a unique approach with mixed molten carbonates as a reaction medium for CO 2 -ODH, which strategically partitions the CO 2 -ODH reactions into gas and molten-salt phases and facilitates integrated CO 2 capture from power plant flue gases. An 89% CO yield was achieved at 770°C, doubling the equilibrium limitation of conventional CO 2 -ODH. The high CO yield in turn enhances ethylene formation. Further characterizations confirmed that molten-salt mediated ODH (MM-ODH) proceeds through a gas-phase cracking and molten-salt mediated reverse water-gas-shift reaction pathway. Based on this understanding, thermodynamic analysis and ab initio molecular dynamics simulations were conducted to develop general principles to optimize the molten-salt reaction medium. Process analyses confirm that MM-ODH has the potential to be significantly more efficient for CO 2 capture and utilization than conventional CO 2 -ODH.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Inverse mapping of properties to composition through generative modeling for designing molten salts

Generative modeling (GM) has been increasingly used for the inverse design and optimization of materials, yet its application to molten salt mixtures remains unexplored despite how a successful approach to the inverse design of molten salts would contribute to efficiently exploiting their customizability and unlocking their advantages in applications, such as energy production and energy storage. This work presents a workflow for the inverse design of molten salts with targeted density values, addressing the challenge of representing these complex mixtures in GM. A dataset of critically evaluated molten salt densities is used to train a variational autoencoder coupled with a predictive deep neural network, which then can be used to generate new molten salt compositions with desired density values. The effectiveness of the approach is demonstrated by designing mixtures with distinct densities and validating the predicted values using ab initio molecular dynamics simulations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Development and Experimental Validation of a Heat Transfer Model for Spilled Molten Salt Pools

A spill of radionuclide-bearing molten salt is one of the major postulated events that needs to be analyzed for liquid fluorine salt-cooled high-temperature reactor (FHR) or molten salt reactor licensing purposes. In this postulated event, radioactive source term materials (RSTMs) in the molten salt are discharged from the reactor vessel to the reactor building. The release of RSTMs from the spilled salt pool to the gas space in the reactor building is expected to be controlled by the cooling behavior of the spilled salt, including the growth and shrinkage of the solid crust on the surface of the spilled salt pool. This paper presents a simulation model for spilled salt pool heat transfer and validation efforts. The validation data come from two molten salt spill tests that were performed recently: the PELE2 test by the Rapid Experimental Laboratory of Kairos Power LLC (KP) and the Argonne salt cooling test conducted by Argonne National Laboratory. The former was a large-scale test involving kilograms of molten spilled FLiNaK salt, and the latter was a relatively smaller-scale test targeting various processes associated with a salt spill event. Both tests generated valuable data sets that can be used to assess salt cooling and validate evaluation models. This paper provides a new one-dimensional model that can simulate the cooling process of a spilled salt pool as well as the thermal responses of heat structures, such as the stainless steel liner and the concrete below the salt. The model has been implemented as part of KP-SAM code, which is a branch of the systems code SAM specific to KP FHR. In conclusion, the simulation results of the model are compared with the data of the PELE2 and Argonne tests, and reasonable agreements are observed between the model and test data.

heat transfer model↗

DOE OSTI2025

Assessment of RELAP5-3D Code with Molten Salt Heat Transfer Experiments

The accurate thermal-hydraulic assessment of thermal storage systems is crucial for addressing the integrity and performance of the storage system design. This is particularly important for thermal storage systems using molten salts as a heat transport and storage medium, as the chemical corrosion and erosion by the high-temperature molten salts can cause serious damage to the structural components of the storage system. To understand these effects for TerraPower’s Natrium® Demonstration Reactor design, the system thermal-hydraulic analysis code, RELAP5-3D, is utilized to analyze the thermal storage system. This study evaluates two heat transfer correlations implemented in the RELAP5-3D code—the Dittus-Boelter and Gnielinski correlations—using selected benchmark cases from two molten salt heat transfer experiments conducted at Xi’an Jiao Tong University and the German Aerospace Center. The Nusselt numbers calculated using the Gnielinski correlation agree with the experimental data within ±5% of the relative deviations at 300°C and 400°C. With the increasing Reynolds numbers, the Dittus-Boelter correlation underestimates the Nusselt numbers by up to 22% compared to the Gnielinski correlation. Comparison of the RELAP5-3D calculation results with experimental data at a high temperature of 550°C revealed that the thermo-chemical characteristics of solar salt at high temperatures surpassing the decomposition temperatures of nitrate salts reduce the accuracy of heat transfer model of the RELAP5-3D code. Specifically, it has been observed that the temperatures of the wall surface and liquid near the wall can surpass the decomposition temperatures, even though the bulk temperature of molten salts remains significantly lower than these decomposition temperatures. In summary, this study recommends the use of the Gnielinski correlation for the heat transfer analysis of molten salt, rather than the Dittus-Boelter correlation.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗

DOE OSTI2026

Development of MOSCATO: A CFD-Level Electrochemistry and Corrosion Simulator for Molten Salt Systems

For both coolant and fueled variants of molten salt reactors (MSRs), the corrosion of structural materials is a significant challenge. The corrosion stems from chemical and electrochemical reactions initiated by fissile material, fission products, and impurities in the salt. Lower-fidelity models rely on empirical correlations for mass transfer, simplified lumped temperature profiles, and similar assumptions. They do not capture detailed spatial variations in complex geometries, creating the need for high-fidelity modeling to bridge this gap.As we approach the demonstration and possible deployment of MSRs in this decade, the development of a high-fidelity, high-performance simulator becomes imperative. To simulate the complex electrochemical environment and corrosion within molten salt systems, we have developed the Molten Salt Chemistry And TranspOrt (MOSCATO) code. This endeavor is comprised of three essential components. First, mass transfer equations are coupled with the Navier-Stokes equations in order to account for the transport of species in the salt. Second, the diffusion of alloy constituents, such as Cr, Fe, Ni, etc. is simulated within the structural metals. Third, the alloy and salt domains are coupled to account for the heterogeneous chemical and electrochemical reactions that occur at the salt-alloy interface.MOSCATO manages all three components within the framework of the highly scalable, open-source spectral element method computational fluid dynamics code Nek5000/NekRS. This integration enables MOSCATO to harness the immense computational power of modern high-performance computing resources, ensuring both high fidelity and computational speed.In addition to code development, we have initiated a comprehensive verification and validation campaign, utilizing data from diverse sources. First, MOSCATO's electrochemical solver was verified with reference numerical data. Then validation occurred against experiments: one of a thermal galvanic cell and the other for corrosion in flowing molten salt of FLiNaK (LiF-NaF-KF). This campaign verified and validated MOSCATO as a reliable tool for simulating electrochemical environments and corrosion in molten salt systems.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Computational Fluid Dynamics Analysis of the Molten Salt Tritium Transport Experiment Test Section

Tritium, a radionuclide produced through neutron capture by lithium and other elements (beryllium and fluoride) in molten salts, presents unique challenges to radionuclide release. This is true for both fusion energy breeder blankets and molten salt fission reactors. The fundamental understanding of tritium transport is crucial to the safe design and operation of these reactors. The Molten Salt Tritium Transport Experiment (MSTTE), currently under construction at Idaho National Laboratory, aims to investigate tritium transport phenomena using a forced-convection fluoride salt loop. This loop is designed to study various transport mechanisms, such as permeation through metals and gas-liquid interactions, and is intended to support future research on tritium extraction units. A critical aspect of the MSTTE loop design is ensuring a fully developed velocity profile before the fluid reaches the permeation test section where measurements are made. This study employs computational fluid dynamics to model the salt flow behavior within the MSTTE permeation test section. A realizable k-ε turbulent model with enhanced wall treatment is used to simulate the single-phase, vertical upward flow of molten salt FLiNaK under isothermal conditions. The simulation results indicated flow distortion and underdeveloped profiles at all planned flow rates within the test section due to the 85-deg sharp bend. To address this issue, a reduced diameter with a reducer and expander and a flow conditioner are investigated to achieve fully developed flow. The analysis showed that the flow conditioner successfully corrected the flow profile, achieving fully developed behavior at a flow rate of 50 liters per minute (LPM). In conclusion, this research enhances our understanding of flow dynamics in molten salt systems and contributes to optimizing tritium transport control technologies.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Predicting and understanding corrosion in molten chloride salts

Abstract Molten chloride salts are stable at higher temperatures than many other salts, including nitrate salts, and are thus promising for heat transfer and/or thermal energy storage in concentrating solar power, nuclear power, and other thermal energy storage applications. However, corrosion in molten chloride salts remains a significant problem. While many studies have been devoted to evaluation of corrosion, we find that a comprehensive method for predicting corrosion in molten chloride salts is lacking. Here, we present an evaluation of corrosion in molten chloride salts using Ellingham diagrams and chloride-oxide stability diagrams, which enable prediction of alloy performance in molten chloride salts and allow corrosion results to be interpreted at a fundamental level. Graphical abstract

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2025

Molten Salt Corrosion Tests of Additively Manufactured Stainless Steel 316H

Molten salt reactors (MSRs) have drawn considerable interest due to their favorable safety features, high thermal efficiency, and compatibility with different fuel cycles. Yet, the success of MSRs hinges critically on the performance of structural materials to be used in these aggressive molten salt environments, where corrosion and material compatibility remain primary challenges to long-term reliability. Additively manufactured (AM) nuclear structural materials prompt the use of novel geometries and compositions to enhance material performance and reduce costs of constructing MSRs. The rapid solidification conditions inherent to AM processing impart distinctive microstructural features, including cellular sub-structures, dislocation densities, residual stress, and oxide inclusions, which can influence material performance in MSR components. While the mechanical properties of AM stainless steels have been widely studied, their corrosion behavior, particularly in molten salt environments, has received far less attention. Addressing these needs, the Advanced Materials and Manufacturing Technologies (AMMT) program provides a framework for systematically evaluating how unique microstructures produced by AM processes influence the performance of these materials in these demanding environments and for developing reproducible testing workflows that can support future code qualification efforts and standards development. Bridging this knowledge gap is essential for assessing the viability of AM alloys in MSRs and informing qualification strategies. A further challenge is the absence of standardized protocols for molten salt corrosion testing. Accordingly, this report provides an account of the corrosion evaluation of AM 316H stainless steel in NaCl 2 -MgCl 2 molten salt at 550 °C, with exposure times of 100 and 500 hours. It documents the experimental procedures implemented under the AMMT program, including salt preparation, exposure protocols, and post-test characterization methods, to establish reproducibility and transparency. Importantly, the study examines AM 316H samples in the as-fabricated condition, directly reflecting the surface state most relevant to engineering applications, and compares their behavior to machine-cut surfaces. Overall, preliminary evaluations have noted that surface conditions (e.g. morphology, contamination, etc.) have a noticeable impact on the corrosion resiliency. The impact of the corrosion is difficult to detect at 100h, unless, in the case of AM 316H, the specimen surface is decontaminated. After 500 h, as-fabricated surfaces of AM and wrought 316H display evidence of general versus preferential corrosion attack, respectively. Both AM and wrought 316H machine-cut surfaces exhibit a continuous Cr depletion zone, evident of general corrosion. While the estimated extent of corrosion appears within the same order of magnitude regardless of the surface condition, it is apparent that more predictable behavior is observed on machine-cut surfaces. Nonetheless, further investigation is necessary to fully elucidate the corrosion mechanism under these conditions.

36 - MATERIALS SCIENCE↗

DOE OSTI2020

Analysis of the Impurity MgOHCl in Molten Chloride Salts Toward its Electrochemical Removal from CSP Plants During Operation

The work presented here is a study of the impurity MgOHCl in molten chloride salts, toward the eventual goal of electrochemically removing it from operational molten-chloride-based concentrating solar power (CSP) plants.1,2 Implementation of molten chloride salts as a heat transfer fluid is among the most promising pathways for decreasing the levelized cost of energy (LCOE) of CSP systems because its high thermal stability allows higher operating temperatures, and thus, greater efficiency. However, this impurity - formed when MgCl2 salts are exposed to air and moisture - cause significant corrosion of containment alloys.1 Therefore, we have developed and validated in a laboratory setting: 1) a method for the formation of MgOHCl for controlled impurity spike in molten salt for its further sensing, evaluation, and reduction; 2) evaluated its diffusion in the molten salt, and 3) began assessing its electrochemical properties. Our findings allow us to propose solutions for efficiently and instantly removing MgOHCl from an operational CSP plant.

concentrated solar power↗

DOE OSTI2021

Suggestions on the Vapor Pressure Determination of Molten Salts

The knowledge of the thermophysical properties of coolant and fuel in molten salts nuclear reactors (MSRs), such as thermal stability and vapor pressure, are of remarkable interest, particularly for simulating safe reactor operations. Molten salt reactorsMSRs use molten salt mixtures as the primary coolant and/or fuel and are expected to operate up to 800 °C. With the revival of interest in deploying MSRs, complete thermophysical and thermochemical characterization of these materials is of interest to industry, regulators, and researchers. Vapor pressure data for molten salts are scarce in the literature, both for pure salts but especially for eutectic mixtures. This report describes the effusion method, which consist of measuring the rate of escape of vapor molecules through a small orifice for the determination of the vapor pressure of compounds and may be useful on compounds such as molten salts. Thermogravimetric analysis records the mass loss as a function of time and temperature. There are two equations that can be used to relate the mass loss rate with the vapor pressure: (1) the Knudsen equation and (2) the Langmuir equation. To apply these equations, the system needs to reach a pseudo (or near) equilibrium condition. Therefore, the experimental conditions must be such that allow the condensed and the vapor/gas phases to be in equilibrium. In order to accomplish equilibrium like conditions, the sample must be in an almost-sealed cell except for a small orifice, from where the vapor escapes. In the Knudsen method vacuum is applied to eliminate the effect that the presence of other gas molecules could have on the evaporation rate of the sample. However, Langmuir alleged that in certain conditions, such as at low temperatures and/or when the vapor pressure is low, the rate of evaporation of a substance is independent of the presence of vapor around it. For that reason, some researchers, when measuring the mass loss of a substance with a predictable low vapor pressure, do not apply vacuum when using the Langmuir equation. However, they use a standard substance to parameterize the experimental setup. The use of one equation or the other will depend on the characteristics of the sample and the availability of an appropriate standard. Some important aspects related to the nature of the samples and vapor pressure measurements are described for future consideration.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2021

Implementation of an Experimental Setup Based on the Three-Omega Method for Thermal Conductivity Measurements of Molten Salts

Molten salt reactors (MSRs) are one of the most promising next-generation nuclear reactor designs which use molten salts as the fuel and coolant. To design, model, predict, license, and operate MSRs, the behavior of the fuel and coolant must be understood as a function of temperature and irradiation, i.e., burnup. Of particular importance and complexity is the reliable and reproducible measurement of thermal conductivity of molten salts at high temperatures (> 500 °C). Thermal conductivity provides information on the rate at which heat passes through a specified material and is dependent on chemical composition. Currently, in the national laboratory complex, several methods for measuring thermal conductivity on molten salt systems are under development, however, to date, consistent data have not been produced. Typically, thermal conductivity measurements of high-temperature melts have been conducted by using the Transient Hot Wire (THW) method where thermal conductivity is determined by the change in temperature over time at a certain distance from a heating wire. Another time-dependent technique is the laser flash method, commonly used for solid samples. Laser flash requires prior measurements of density and heat capacity to calculate the thermal conductivity of the sample, introducing additional measurement errors. Steady state and time-dependent measurements such as THW and laser flash have errors from convection and ambient temperature fluctuations (heat radiation). In order to produce high fidelity thermal conductivity data, a measurement technique needs to be developed that will reduce the effect of convection at high temperatures by measuring in a very fast time window. In addition, to measure on actinide and irradiated salts the sample size should be small. Therefore, this project aims to develop a frequency-domain technique based on the three-omega (3?) method, previously proven to work on solids, nanofluids and low temperature solar salts (25 to 250 °C). If the 3?-device can be designed with materials that can withstand high temperatures (>500 °C) and can be configured to reduce errors due to convection, then it would prove to be a valuable technique for ensuring thermal conductivity on molten salt systems needed for MSR development. For this proposal, the 3? instrument will be designed, assembled, and tested on non-radioactive salts before being used on actinide bearing salts. In addition, a thermal model will be developed to determine the thermal conductivity of the sample from the measured thermal oscillation of the sensor. Because 3? is a direct method that requires a small volume of sample and works in a very fast time window, it will aid in suppressing the interference due to convection which is ideal when working with high temperature liquid samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Molten Salt Tritium Transport Experiment: A Versatile Fluoride Salt Loop for Validation of Tritium Transport Phenomena

Tritium is generated in Molten Salt Reactors (MSRs) from neutron capture by lithium and other constituents of the molten salt FLiBe. Tritium is a unique radionuclide as it readily permeates through hot structural materials. Thus, any material in contact with tritium laden molten salt is a potential pathway for release. Understanding tritium transport and devising adequate control strategies is necessary for the safe operation of MSRs. The Molten Salt Tritium Transport Experiment (MSTTE) is a forced-convection fluoride salt loop with the capability to inject hydrogen isotopes into flowing molten salt and to measure transport phenomena such as permeation through metals and evolution from free-surfaces. MSTTE is designed to be versatile to test potential control technology in future campaigns. This report focuses on the current design and analysis of MSTTE. Custom designed and fabricated experiment components such as the hydrogen injection system, permeation test section, diagnostics, and gas distribution system are discussed in detail. System-level tritium transport modeling using the System Analysis Module investigates experiment parameters such as hydrogen source terms, salt flow rate, and salt temperature. Computational fluid dynamics of the salt flow in the permeation test section informs design choices to establish fully developed flow in the measured permeation zone.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2024

Inaugural Molten Salt Technologies Workshop Powering the Future

The inaugural “Molten Salt Technologies – Powering the Future” Workshop marked a significant convergence of minds from diverse industries, each harnessing molten-salt technologies in innovative ways. Participants from sectors such as solar, geothermal, and advanced nuclear energy, as well as those involved in cutting-edge applications like thermal transport and rare-earth metals extraction, gathered to discuss their shared technical challenges and opportunities. Industry leaders in metal extraction and recycling, alongside experts in high-temperature sensor technology and advanced material manufacturing, also brought their unique perspectives to the table. This workshop served as a crucial platform for these varied industries to delve into the engineering intricacies that molten salt technologies entail. Common challenges such as understanding the thermophysical properties of salts, tackling corrosion mechanisms in harsh environments, and enhancing material resilience under extreme conditions were at the forefront of discussions. These technical sessions highlighted the critical need for cross-industry collaboration to address issues like salt life-cycle process engineering, impurity mitigation, and the development of durable, high-performance materials. By bringing together academia, industry, and representatives from national laboratories and the U.S. Department of Energy (DOE), the workshop facilitated a rich exchange of knowledge and experiences. This interaction not only fostered new partnerships but also strengthened the network among existing collaborators, setting the stage for joint solutions to the complex problems faced by all sectors using molten salt technologies. The event underscored the importance of collaborative efforts in overcoming common engineering challenges and advancing the application of molten-salt technologies across various industries. The workshop not only provided an essential forum for networking and idea exchange but also highlighted the collective drive towards innovative solutions that could benefit multiple fields.

Department of Energy↗

DOE OSTI2024

Inaugural Molten Salt Technologies Workshop Powering the Future

Department of Energy↗

DOE OSTI2025

Solvated Electrons Have Multiple Personalities in Molten Salts

P-Crosscut: Solvated Electrons Have Multiple Personalities in Molten Salts [EFRC – MSEE] Alejandro Ramos-Ballesteros;1 Hung H. Nguyen;2 Kazuhiro Iwamatsu;3 Santanu Roy;4 Vyacheslav Bryantsev;4 Michael E. Woods;1 Ruchi Gakhar;1 Phillip Halstenberg;4 Bobby Layne;5 Jay A. LaVerne;6 Claudio J. Margulis:2* and James F. Wishart5* 1Idaho National Laboratory; 2The University of Iowa; 3Hunter College; 4Oak Ridge National Laboratory; 5Brookhaven National Laboratory; 6University of Notre Dame Abstract: The solvated (eS–) is a powerful reducing agent and one of the primary products of molten salt radiolysis. In these extreme high-temperature environments, the eS– can initiate cascades of redox processes that significantly alter the physical and chemical properties of a molten salt, posing challenges for molten salt reactor (MSR) performance and longevity. Consequently, mastering the fundamental behavior of the eS– could enable the design of specific molten salt mixtures with tailored Lewis acidities for controlling the speciation and chemical reactivity of the eS–, thereby mitigating its overall impact on MSR technologies. Here, we use time-resolved electron pulse radiolysis techniques for determining chemical kinetics and transient absorption spectra, combined with ab initio molecular dynamics simulations to explore the influence of multivalent metal cations on the fundamental speciation and distribution of eS– coordination environments.

38 - RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCL↗

DOE OSTI2026

Understanding the speciation of molten iodide salts via spectro-electrochemistry

Iodine is a high yield fission product of concern for the environmental effects due to its high volatility and biological impacts to the human body. Iodine speciation in molten salts, specifically iodide salts, is not well understood due to its reactivity at higher temperature domains. UV-Vis spectroscopy indicates a change in the speciation of the molten iodide salts starting at 500oC based on the decomposition of the salt itself, forming I3- ions. This work investigated the spectral changes of I- ions in molten LiI-KI and LiI-KI-NiI2 while manipulating the salts electrochemically using an inert graphite electrode at 400oC.The Li+/Li(s) and the Ni2+/Ni(s) transitions were studied using cyclic voltammetry, chronoamperometry/chronopotentiometry to characterize the respective reduction-oxidation waves. As cyclic voltammetry was applied, the UV-Vis spectroscopy showed a change in the characteristic signal of molten LiI-KI, indicating a disproportionation reaction in the molten salt, leading to formation of I3- ions and I2 gas.

36 - MATERIALS SCIENCE↗

DOE OSTI2024

On the applicability of the Redlich-Kister framework for viscosity estimation of molten halide salt mixtures

For molten halide salt mixtures already being utilized or under consideration for carbon-free energy production systems, it is crucial that their viscosity is well understood so that system thermal hydraulics can be reliably assessed. Because of the difficulty in accurately measuring molten halide viscosity and the sheer size of the matrix of possible higher order salt mixtures that may be of interest to the energy industry, there are several gaps in the quantified understanding of molten halide viscosity across this matrix. As such, both first-principles and semi-empirical modeling techniques may be crucial for rapidly assessing this broad, complex compositional domain. Herein, the Redlich-Kister framework is applied to assess the feasibility of broadly interpolating and estimating the viscosity of several pseudobinary and pseudoternary molten halide salt systems that may be of key interest to the energy industry. The framework is based on the assumption that an ideal component and a nonideal component collectively describe the viscosity as a function of composition and temperature for a given molten halide system. Three different ideal models were considered for the ideal component, including Grunburg-Nissan, Katti-Chaudhri, and Gambill methods. Regarding the pseudobinary interpolations, the Redlich-Kister models with either the Grunburg-Nissan or Katti-Chaudhri models as the ideal component resulted in either highly (average error less than 5%) or reasonably (average error less than 15%) accurate interpolations of pseudobinary halide viscosity; BeF 2 - or UF 4 -bearing salts tended to result in reasonably accurate interpolations, whereas other pseudobinary mixtures tended to show high accuracy. Regarding the pseudoternary extrapolations, the Redlich-Kister framework shows reasonable success at estimating the extent to which a pseudoternary system may indicate deviations from ideal Grunburg-Nissan mixing, where discrepancies with comparative experimental data generally stay within 30%. Finally, the primary reasons identified for such discrepancies are (1) inaccuracy in the underlying experimental data, (2) different complexation behavior in the higher order systems compared to the pseudobinary subsystems, and (3) extrapolation into temperatures too far out of the domain, which is valid for the underlying experimental data feeding the Redlich-Kister model.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗