Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Material microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

A study of fiber volume fraction effects in notched unidirectional SCS-6/Ti-15V-3Cr-3Al-3Sn composite

Notched unidirectional SCS-6/Ti-15-3 composite of three different fiber volume fractions (vf = 0.15, 0.37, and 0.41) was investigated for various room temperature microstructural and material properties including: fatigue crack initiation, fatigue crack growth, and fracture toughness. While the matrix hardness is similar for all fiber volume fractions, the fiber/matrix interfacial shear strength and matrix residual stress increases with fiber volume fraction. The composite fatigue crack initiation stress is shown to be matrix controlled and occurs when the net maximum matrix stress approaches the endurance limit stress of the matrix. A model is presented which includes residual stresses and presents the composite initiation stress as a function of fiber volume fraction. This model predicts a maximum composite initiation stress at vf approximately 0.15 which agrees with the experimental data. The applied composite stress levels were increased as necessary for continued crack growth. The applied Delta(K) values at crack arrest increase with fiber volume fraction by an amount better approximated using an energy based formulation rather than when scaled linear with modulus. After crack arrest, the crack growth rate exponents for vf37 and vf41 were much lower and toughness much higher, when compared to the unreinforced matrix, because of the bridged region which parades with the propagating fatigue crack. However, the vf15 material exhibited a higher crack growth rate exponent and lower toughness than the unreinforced matrix because once the bridged fibers nearest the crack mouth broke, the stress redistribution broke all bridged fibers, leaving an unbridged crack. Degraded, unbridged behavior is modeled using the residual stress state in the matrix ahead of the crack tip. Plastic zone sizes were directly measured using a metallographic technique and allow prediction of an effective matrix stress intensity which agrees with the fiber pressure model if residual stresses are considered. The sophisticated macro/micro finite element models of the 0.15 and 0.37 fiber volume fractions presented show good agreement with experimental data and the fiber pressure model when an estimated effective fiber/matrix debond length is used.

Covey, Steven J.↗
NASA NTRS2004

Investigation of the Environmental Durability of a Powder Metallurgy Material

PM304 is a NASA-developed composite powder metallurgy material that is being developed for high temperature applications such as bushings in high temperature industrial furnace conveyor systems. My goal this summer was to analyze and evaluate the effects that heat exposure had on the PM304 material at 500 C and 650 C. The material is composed of Ni-Cr, Ag, Cr2O3, and eutectic BaF2-CaF2. PM304 is designed to eliminate the need for oil based lubricants in high temperature applications, while reducing friction and wear. However, further investigation was needed to thoroughly examine the properties of PM304. The effects of heat exposure on PM304 bushings were investigated. This investigation was necessary due to the high temperatures that the material would be exposed to in a typical application. Each bushing was cut into eight sections. The specimens were heated to 500 C or 650 C for time intervals from 1 hr to 5,000 hrs. Control specimens were kept at room temperature. Weight and thickness measurements were taken before and after the bushing sections were exposed to heat. Then the heat treated specimens were mounted and polished side by side with the control specimens. This enabled optical examination of the material's microstructure using a metallograph. The specimens were also examined with a scanning electron microscope (SEM). The microstructures were compared to observe the effects of the heat exposure. Chemical analysis was done to investigate the interactions between Ni-Cr and BaF2-CaF2 and between Cr2O3 and BaF2-CaF2 at high temperature. To observe this, the two compounds that were being analyzed were mixed in a crucible in varied weight percentages and heated to 1100 C in a furnace for approximately two hours. Then the product was allowed to cool and was then analyzed by X-ray diffraction. Interpretation of the results is in progress.

Ward, LaNita D.↗
NASA NTRS2001

Ultrasonic Data Display and Analysis System Developed (Including Fuzzy Logic Analysis) for the Windows-Based PC

Post-Scan Interactive Data Display (PSIDD) III is a user-oriented Windows-based system that facilitates the display and comparison of ultrasonic contact measurement data obtained at NASA Glenn Research Center's Ultrasonic Nondestructive Evaluation measurement facility. The system is optimized to compare ultrasonic measurements made at different locations within a material or at different stages of material degradation. PSIDD III provides complete analysis of the primary waveforms in the time and frequency domains along with the calculation of several frequency-dependent properties including phase velocity and attenuation coefficient and several frequency-independent properties, like the cross correlation velocity. The system allows image generation on all the frequency-dependent properties at any available frequency (limited by the bandwidth used in the scans) and on any of the frequency-independent properties. From ultrasonic contact scans, areas of interest on an image can be studied with regard to underlying raw waveforms and derived ultrasonic properties by simply selecting the point on the image. The system offers various modes of indepth comparison between scan points. Up to five scan points can be selected for comparative analysis at once. The system was developed with Borland Delphi software (Visual Pascal) and is based on an SQL data base. It is ideal for the classification of material properties or the location of microstructure variations in materials. Along with the ultrasonic contact measurement software that it is partnered with, this system is technology ready and can be transferred to users worldwide.

Lovelace, Jeffrey J.↗
NASA NTRS2006

Tensile and Creep Property Characterization of Potential Brayton Cycle Impeller and Duct Materials

This paper represents a status report documenting the work on creep of superalloys performed under Project Prometheus. Cast superalloys have potential applications in space as impellers within closed-loop Brayton cycle nuclear power generation systems. Likewise wrought superalloys are good candidates for ducts and heat exchangers transporting the inert working gas in a Brayton-based power plant. Two cast superalloys, Mar-M247LC and IN792, and a NASA GRC powder metallurgy superalloy, LSHR, are being screened to compare their respective capabilities for impeller applications. Several wrought superalloys including Hastelloy X, (Haynes International, Inc., Kokomo, IN), Inconel 617, Inconel 740, Nimonic 263, and Incoloy MA956 (Special Metals Corporation, Huntington, WV) are also being screened to compare their capabilities for duct applications. These proposed applications would require sufficient strength and creep resistance for long term service at temperatures up to 1200 K, with service times to 100,000 h or more. Conventional tensile and creep tests were performed at temperatures up to 1200 K on specimens extracted from the materials. Initial microstructure evaluations were also undertaken.

Gabb, Timothy P.↗
NASA NTRS2013

High Temperature Stable Nanocrystalline SiGe Thermoelectric Material

A method of forming a nanocomposite thermoelectric material having microstructural stability at temperatures greater than 1000 C. The method includes creating nanocrystalline powder by cryomilling. The method is particularly useful in forming SiGe alloy powder.

Yang, Sherwin↗
NASA NTRS2023

STXM-C-XANES, IR Microspectroscopy, and Raman Microspectroscopy Analysis of Organic Matter in the Chwichiya 002 C3.00-Ungrouped Chondrite

Chwichiya 002 is a C3.00-ungrouped carbonaceous chondrite discovered in Western Sahara in 2018. The presence of hydrated phases in Chwichiya 002 was not confirmed by XRD analysis, and only a faint water and Si-O band attributed to phyllosilicate were observed by infrared transmission spectroscopy, indicating a very low degree of aqueous alteration (Meteoritical Bulletin, 2020). The structural order of polycyclic aromatic hydrocarbons evaluated by Raman spectroscopy indicates that the effect of thermal metamorphism is less severe than in the Semarkona meteorite, an LL3.00 ordinary chondrite (Meteoritical Bulletin, 2020). Chiwichiya 002 is a very primitive carbonaceous chondrite and an important information source for the early stage of the evolution of organic matter in the solar system. In this study, we investigated the molecular structure and distribution of organic matter in Chiwichiya 002 by Carbon X-ray Absorption Near Edge Structure (C-XANES) analysis using a Scanning Transmission X-ray Microscope (STXM). The STXM-C-XANES analysis has a spatial resolution of 20~100 nm and can observe the spatial distribution of organic materials in microstructures. In addition, to investigate the degree of thermal metamorphism of the organic matter, micro-IR, and micro-Raman spectroscopic analyses were performed. In addition, the Murchison CM2 chondrite was also analyzed for comparison. To evaluate contamination during analytical procedures, antigorite, which was heated in air at 500°C for 5 hours to eliminate organic matter was also analyzed in the same manner. The samples were milled into 100 nm-thick, thin sections using a Focused Ion Beam (FIB), and C-XANES spectra were obtained using the STXM at the High Energy Accelerator Research Organization, Photon Factory (PF), BL-19B. The obtained C-XANES spectra were smoothed and then fitted with Gaussian functions using the method of Le Guillou et al. (2018). The C-XANES showed that the ratio of oxygenated functional group (ketone, phenolic) carbons in Chwichiya 002 was lower than in Murchison, whereas the ratio of aliphatic carbons was almost the same. This may reflect the low degree of aqueous alteration of Chwichiya 002. In addition, contamination peaks were detected at 287.3-287.7 eV and 288.3-288.7 eV in the C-XANES spectra of some of the antigorite samples. The source of these peaks is under investigation. Raman spectroscopic analysis showed that the intensity ratio of the D band to the G band of Chwichiya 002 was slightly higher than that of Murchison. IR absorption spectra showed aromatic absorption at 1630 cm -1 , but there was little absorption due to aliphatic C-H around 2900 cm -1 . These results suggest that the organic matter in Chwichiya 002 may be more heated than in Murchison.

Chwichiya 002↗
NASA NTRSDate not supplied

Multiscale Modeling of Woven Ablative Thermal Protection System Materials

The NASA Entry Systems Modeling project maintains a portfolio of computational model and tool development activities focused on reducing performance uncertainties in ablative Thermal Protection System (TPS) materials for NASA missions. The development activities span material scale and strive to allow microstructural characterization of material structure and properties, mesoscale analyses of damage, and macroscale evaluation of heatshield performance and recession in a given aerothermodynamic environment. This talk will detail the application of developed capabilities at all three scales to the woven TPS material that the Agency has selected as the heatshield for the Mars Sample Return Earth Entry System (MSR-EES) mission – 3D Mid-Density Carbon Phenolic (3MDCP). Each of the applications focuses on driving down uncertainties in material performance and thus risk for MSR-EES and other future missions that may leverage woven TPS. At the microscale, machine learning techniques are used to characterize images from destructive microscopy and inform structural variability. At the mesoscale, Lagrangian techniques are used to simulate ballistic impact and interpret damage modes noted in experiments. At the macroscale, coupled flow-material response techniques are validated by Arc Jet testing to enable heatshield design for missions with massive ablation.

Justin B Haskins↗
NASA NTRS1999

A Phenomenological Description of Primary Creep in Class M Materials

Observations of creep microstructures in the primary creep region in class M materials show a remarkable similarity with those formed in the exponential creep regime. As a result, it is proposed that the constitutive creep law for normal primary creep is similar to that for the exponential creep regime. A phenomenological description is discussed to rationalize these microstructural observations in terms of a normalized strain rate vs. stress plot. The implications of this plot in describing different testing procedures, steady-state flow, and on the observed deviations from the universal creep law are discussed. The plot is also extended to explain the observed similarities in the transient creep behavior in pre-strained materials and in stress change experiments.

Raj, S. V.↗
NASA NTRS2001

Evolution of Local Microstructures: Spatial Instabilities of Coarsening Clusters

This work examines the diffusional growth of discrete phase particles dispersed within a matrix. Engineering materials are often microstructurally heterogeneous, and the details of the microstructure determine how well that material performs in a given application. Critical to the development of designing multiphase microstructures with long-term stability is the process of Ostwald ripening. Ripening, or phase coarsening, is diffusion-limited and arises in polydisperse multiphase materials. Growth and dissolution occur because fluxes of solute, driven by chemical potential gradients at the interfaces of the dispersed phase material, depend on particle size. Competitive kinetics of these processes dictates that larger particles grow at the expense of smaller ones, overall leading to an increase of the average particle size. The classical treatment of phase coarsening was done by Todes, Lifshitz, and Slyozov, (TLS) in the limit of zero volume fraction, V(sub V)=0 of the dispersed phase. Since the publication of TLS theory, there have been numerous investigations, many of which sought to describe the kinetic scaling behavior over a range of volume fractions. Some studies in the literature report that the relative increase in coarsening rate at low (but not zero) volume fractions compared to that predicted by TLS is proportional to V(exp 1/2)(sub v) whereas others suggest V(exp 1/3)(sub v).This issue has been addressed recently by simulation studies at low volume fractions in three dimensions by members of the Rensselaer/MSFC team.

Glicksman, Martin E.↗
NASA NTRSDate not supplied

Computational Characterization and Model Verification for 3D Microstructure Reconstruction of Additively-Manufactured Materials

The goal of this study is to characterize and validate the texture and grain topology of additively-manufactured anisotropic three-dimensional (3D) polycrystalline microstructures. The special focus is on developing methodologies to compare the grain shapes and orientations of two-dimensional (2D) and 3D microstructure representations using the same metric. To generate statistical data, synthetic microstructures are reconstructed from experimental data using Markov random field (MRF). The statistical similarity between the experimental and synthetic microstructures is verified by comparing their grain topologies. A universal measure to compare 2D and 3D grains is portrayed through the concept of image moments that are invariant to shape transformations. The graphical plots developed based on moment invariants to compare the 2D and 3D grains are used to verify the synthetic model

Materials Characterization↗
NASA NTRS1986

Analytical ultrasonics for structural materials

The application of ultrasonic velocity and attenuation measurements to characterize the microstructure of structural materials is discussed. Velocity measurements in cast stainless steel are correlated with microstructural variations ranging from equiaxed (elastically isotropic) to columnar (elastically anisotropic) grain structure. The effect of the anisotropic grain structure on the deviation of ultrasonic waves in cast stainless steel is also reported. Field-implementable techniques for distinguishing equiaxed from columnar grain structures in cast strainless steel structural members are presented. The application of ultrasonic velocity measurements to characterize structural ceramics in the green state is also discussed.

Kupperman, D. S.↗
NASA NTRS2011

Simultaneous Noncontact Precision Imaging of Microstructural and Thickness Variation in Dielectric Materials Using Terahertz Energy

A process for simultaneously measuring the velocity of terahertz electromagnetic radiation in a dielectric material sample without prior knowledge of the thickness of the sample and for measuring the thickness of a material sample using terahertz electromagnetic radiation in a material sample without prior knowledge of the velocity of the terahertz electromagnetic radiation in the sample is disclosed and claimed. The process evaluates, in a plurality of locations, the sample for microstructural variations and for thickness variations and maps the microstructural and thickness variations by location. A thin sheet of dielectric material may be used on top of the sample to create a dielectric mismatch. The approximate focal point of the radiation source (transceiver) is initially determined for good measurements.

Roth, Donald J↗
NASA NTRS1995

Superconducting materials processing

The effects of materials processing on the properties and behavior of high temperature yttrium barium copper oxide (YBCO) superconductors were investigated. Electrical, magnetic, and structural characteristics of thin films (300 nm) YBA2CU3O(delta) structures grown by pulsed laser deposition on LaAlO3 and SrTiO3 substrates were used to evaluate processing. Pole projection and thin film diffraction measurements were used to establish grain orientation and verify structural integrity of the samples. Susceptibility magnetization, and transport measurements were used to evaluate the magnetic and electrical transport properties of the samples. Our results verified that an unfortunate consequence of processing is inherent changes to the internal structure of the material. This effect translates into modifications in the properties of the materials, and undesired feature that makes it very difficult to consistently predict material behavior. The results show that processing evaluation must incorporate a comprehensive understanding of the properties of the materials. Future studies will emphasize microstructural characteristics of the materials, in particular, those microscopic properties that map macroscopic behavior.

Hurley, John S.↗
NASA NTRS2002

Efficient Reformulation of HOTFGM: Heat Conduction with Variable Thermal Conductivity

Functionally graded materials (FGMs) have become one of the major research topics in the mechanics of materials community during the past fifteen years. FGMs are heterogeneous materials, characterized by spatially variable microstructure, and thus spatially variable macroscopic properties, introduced to enhance material or structural performance. The spatially variable material properties make FGMs challenging to analyze. The review of the various techniques employed to analyze the thermodynamical response of FGMs reveals two distinct and fundamentally different computational strategies, called uncoupled macromechanical and coupled micromechanical approaches by some investigators. The uncoupled macromechanical approaches ignore the effect of microstructural gradation by employing specific spatial variations of material properties, which are either assumed or obtained by local homogenization, thereby resulting in erroneous results under certain circumstances. In contrast, the coupled approaches explicitly account for the micro-macrostructural interaction, albeit at a significantly higher computational cost. The higher-order theory for functionally graded materials (HOTFGM) developed by Aboudi et al. is representative of the coupled approach. However, despite its demonstrated utility in applications where micro-macrostructural coupling effects are important, the theory's full potential is yet to be realized because the original formulation of HOTFGM is computationally intensive. This, in turn, limits the size of problems that can be solved due to the large number of equations required to mimic realistic material microstructures. Therefore, a basis for an efficient reformulation of HOTFGM, referred to as user-friendly formulation, is developed herein, and subsequently employed in the construction of the efficient reformulation using the local/global conductivity matrix approach. In order to extend HOTFGM's range of applicability, spatially variable thermal conductivity capability at the local level is incorporated into the efficient reformulation. Analytical solutions to validate both the user-friendly and efficient reformulations am also developed. Volume discretization sensitivity and validation studies, as well as a practical application of the developed efficient reformulation are subsequently carried out. The presented results illustrate the accuracy and implementability of both the user-friendly formulation and the efficient reformulation of HOTFGM.

Zhong, Yi↗
NASA NTRS1987

A microstructural lattice model for strain oriented problems: A combined Monte Carlo finite element technique

A specialized, microstructural lattice model, termed MCFET for combined Monte Carlo Finite Element Technique, was developed which simulates microstructural evolution in material systems where modulated phases occur and the directionality of the modulation is influenced by internal and external stresses. In this approach, the microstructure is discretized onto a fine lattice. Each element in the lattice is labelled in accordance with its microstructural identity. Diffusion of material at elevated temperatures is simulated by allowing exchanges of neighboring elements if the exchange lowers the total energy of the system. A Monte Carlo approach is used to select the exchange site while the change in energy associated with stress fields is computed using a finite element technique. The MCFET analysis was validated by comparing this approach with a closed form, analytical method for stress assisted, shape changes of a single particle in an infinite matrix. Sample MCFET analytical for multiparticle problems were also run and in general the resulting microstructural changes associated with the application of an external stress are similar to that observed in Ni-Al-Cr alloys at elevated temperature.

Gayda, J.↗
NASA NTRS1998

Scaling up the Single Transducer Thickness-Independent Ultrasonic Imaging Method for Accurate Characterization of Microstructural Gradients in Monolithic and Composite Tubular Structures

Ultrasonic velocity/time-of-flight imaging that uses back surface reflections to gauge volumetric material quality is highly suited for quantitative characterization of microstructural gradients including those due to pore fraction, density, fiber fraction, and chemical composition variations. However, a weakness of conventional pulse-echo ultrasonic velocity/time-of-flight imaging is that the image shows the effects of thickness as well as microstructural variations unless the part is uniformly thick. This limits this imaging method's usefulness in practical applications. Prior studies have described a pulse-echo time-of-flight-based ultrasonic imaging method that requires using a single transducer in combination with a reflector plate placed behind samples that eliminates the effect of thickness variation in the image. In those studies, this method was successful at isolating ultrasonic variations due to material microstructure in plate-like samples of silicon nitride, metal matrix composite, and polymer matrix composite. In this study, the method is engineered for inspection of more complex-shaped structures-those having (hollow) tubular/curved geometry. The experimental inspection technique and results are described as applied to (1) monolithic mullite ceramic and polymer matrix composite 'proof-of-concept' tubular structures that contain machined patches of various depths and (2) as-manufactured monolithic silicon nitride ceramic and silicon carbide/silicon carbide composite tubular structures that might be used in 'real world' applications.

Roth, Don J.↗
NASA NTRS1985

Nondestructive determination of mechanical properties

The sensitivity of the velocity of ultrasonic waves to the elasticity of the materials (acousto-elastic constant - AEC) as controlled by the microstructure of the materials was examined experimentally. Rolled-plate specimens of five different Al alloys were subjected to tensile tests while being monitored for the velocity change of a 10 MHz longitudinal wave as a function of the applied tensile stress. The acoustic propagation velocity was measured perpendicularly to the stress. Determinations were made of the yield strength and the hardnesses of the specimens. Samples of the plate materials examined microscopically to characterize the solid phases. The AECs varied linearly with the percentage of solid solution phase of the alloys. The trend for strain-hardened samples was, however, opposite from that in the precipitation-hardened alloys. The results underscore the necessity of considering the microstructural dependencies of the AECs when using ultrasonic NDE methods, and also opened the potential of determining some mechanical properties with NDE techniques.

Schneider, E.↗