Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MECHANICAL PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Effects of irradiation spectrum on the microstructural and mechanical properties of bulk metallic glasses

Zr 52.5 Cu 17.9 Ni 14.6 Al 10 Ti 5 (BAM-11) and Cu60Zr 20 Hf 10 Ti 10 bulk metallic glass (BMG) specimens were ion irradiated to characterize and compare their irradiation induced microstructural and mechanical property evolution. For the ion irradiations, samples of each BMG were exposed to 9 MeV Ni 3+ and 5.5 MeV C + ions to a midrange (~1.5 μm depth) dose of 0.5 displacements per atom (dpa) at temperatures ranging from room temperature to 360 °C in order to examine potential effects associated with low (5.5 MeV C) and high (9 MeV Ni) average primary knock on energies. BAM-11 BMG samples were also irradiated by neutrons (E > 0.1 MeV) at ~70 °C to a fluence of 1.4 × 10 20 n/cm 2 (dose of 0.1 dpa). Importantly, no pronounced irradiation spectrum effects were observed for the nanoindentation mechanical properties of the two BMGs following ion irradiation. However, significant softening was observed in the BAM-11 BMG sample irradiated by neutrons, while annealing of the unirradiated samples led to a marked increase in hardening. Finally, results of the nanoindentation experiments indicate that softening is caused by irradiation induced creation of free volume defects, while the hardening is caused by their annihilation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tuning the Mechanical Properties of a Polymer Semiconductor by Modulating Hydrogen Bonding Interactions

Conjugation breakers (CBs) with different H-bonding chemistry and linker flexibility are designed and incorporated into a Diketopyrrolopyrrole (DPP)-based conjugated polymer backbone. The effects of H-bonding interactions on polymer semiconductor morphology, mechanical properties and electrical performance are systematically investigated. We observe that CBs with H-bonding self-association constant >0.7 or denser packing tendency are able to induce higher polymer chain aggregation and crystallinity in as-casted thin film, resulting in higher modulus and crack on-set strain. Additionally, the rDoC (relative degree of crystallinity) of the stretched thin film with the highest crack on-set strain only suffers a small decrease, suggesting the main energy dissipation mechanism is the breakage of H-bonding interactions. By contrast, other less stretchable polymer films dissipate strain energy through the breakage of crystalline domains, indicated by drastic decrease in rDoC. Furthermore, we evaluate their electrical performance under mechanical strain in fully stretchable field-effect transistors. The polymer with the highest crack on-set strain has the least degradation in mobility as a function of strain. Overall, these observations suggest that we can aptly tune the mechanical properties in polymer semiconductors by modulating intermolecular interactions, such as H-bonding chemistry and linker flexibility. Such understanding provides molecular design guidelines for future stretchable semiconductors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Microstructure and Mechanical Properties of Ni-Based Superalloy Nimonic 105 with Varying Carbon Content

High carbon levels have been found to improve the fabricability of high-strength cast and wrought Ni-based superalloys, enabling the development of superior cast/wrought materials. However, carbon also strongly influences the microstructure and mechanical properties of the alloys. Nimonic 105 variants with three different carbon concentrations were manufactured. A bimodal grain size was found in the intermediate carbon content variant, while the high (low) carbon resulted in fine (coarse) grains thereby significantly affecting creep performance. The variations in grain structure were attributed to the primary carbides. An intermediate carbon level showed the best combination of strength and ductility in tension at high-temperature but little improvement in, or even inferior, creep performance. Discussion of the results will establish an understanding of the influence of carbon on the microstructure and mechanical properties of high strength cast and wrought superalloys, providing insights into obtaining high-quality alloys for future high-temperature applications.

Fang, Xiaotian↗
DOE OSTI2024

Enhanced Mechanical Properties and Wear Resistance of FeCrAl Alloys at ~ 300°C and Higher Temperatures

Abstract Worldwide, light water reactors (LWRs) have been using zirconium (Zr)-based alloys for the cladding of the uranium dioxide fuel for more than 6 decades. Zr alloys oxidize rapidly in the presence of water and steam at temperatures > 450°C; therefore, they do not respond well to scenarios of loss of coolant accidents. There is a global effort by nuclear materials technologists to find more robust or stronger cladding materials for LWRs. One option is to use an iron-chromium-aluminum (FeCrAl) alloy since they have excellent resistance to high temperature oxidation and superior mechanical properties at LWR operation temperatures. Results show that (1) FeCrAl alloys have better mechanical properties than Zr alloy and are orders of magnitude more resistant to creep at temperatures higher than LWR normal operation conditions. (2) FeCrAl alloys have better resistance to fretting wear than Zr alloys at the normal operation conditions of LWRs.

Materials Science↗
DOE OSTI2021

Location-Dependent Mechanical Property Evaluation on Additively Manufacture Materials

This report summarizes research activities conducted at Argonne National Laboratory in support of the development, qualification and certification of additively manufactured (AM) metallic components to allow for innovative reactor design and licensing for the Transformational Challenge Reactor (TCR). Focus is on the evaluation of high temperature mechanical properties including creep and fatigue of 316L stainless steel manufactured by the laser powder bed fusion process. Creep behavior of AM 316L stainless steel was evaluated for rods printed by either or a combination of both lasers of the dual-laser system of a Concept Laser-M2 printer to examine the consistency across the build plate. Creep tests were conducted at temperatures of 550, 575, 600, and 650°C and stresses between 175 and 300 MPa using ASTM standard-sized specimens. The effect of heat treatments at different temperatures on creep properties of AM 316L SS was examined to understand the processing-microstructure-property relationship. Fatigue properties of AM 316L SS were investigated for two print geometries (rod and plate) and in two build orientations of printed plates. Locations of specimens in the build were carefully tracked such that the testing data can be directly related to location-specific in situ data to establish links between printing process, post-printing treatment, microstructure and mechanical properties. The work is to support the development of a digital platform informed approach to AM component qualification and certification for nuclear applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Mechanical properties and strain localization of WA-DED printed P91 steel

This paper discusses a P91 steel block that was additively manufactured by wire arc direct energy deposition (WA-DED) followed by two types of post-process heat treatment (PPHT). Vickers microhardness and digital image correlation tensile tests were performed along the building direction. The global mechanical properties (i.e., microhardness and tensile properties) and the local mechanical responses (i.e., hardness fluctuation and strain localization) were systematically investigated. Results showed that (1) all P91 specimens showed higher strengths than American Society of Mechanical Engineers standard requirements for wrought P91 steel, (2) the as-printed P91 exhibited much higher average hardness and fluctuations than that after PPHT, (3) PPHT reduced P91 strengths but improved the ductility significantly, and (4) strain localization presented in the as-printed specimen during uniform deformation in tensile tests. The hardness fluctuation and strain localization along the building direction of the AP P91 were caused by different thermal histories received during WA-DED. The study indicated that PPHT, ideally tempering-only heat treatment, is necessary for the WA-DED printed P91 steel.

Mechanical properties↗
DOE OSTI2024

Study of Mechanical Properties, Microstructure, and Residual Stresses of AISI 304/304L Stainless Steel Submerged Arc Weld for Spent Fuel Dry Storage Systems

The confinement boundaries of spent nuclear fuel (SNF) canisters are typically fusion welded. Welded microstructures, strain hardening, and residual stresses combined with a chemically aggressive, chloride-rich environment led to concerns that the welded canister may be susceptible to chloride-induced stress corrosion cracking (CISCC). A comprehensive understanding of the modification of stainless steel (SS) metallurgical and mechanical properties by fusion welding could accelerate the predictive analysis of CISCC susceptibility. This paper describes a submerged arc welding (SAW) procedure that was developed and qualified on 12.7 mm (0.5 in.) thick AISI 304/304L SS to produce joints in a way similar to actual SNF canister manufacturing. This procedure has the potential to reduce the production cost and weld CISCC susceptibility by using fewer welding passes and lower heat input than current industrial applications. Global and local mechanical behaviors and properties, as well as residual stress distributions on the welded joint, were studied. The results indicate that hardness values in the fusion zone (FZ) and heat-affected zone (HAZ) are slightly higher than that of the base metal. Strain localization was presented in the HAZ before the tensile stress reached its maximum value, and then it shifted to the FZ. The specimen finally broke in the FZ. High tensile residual stresses exhibited in the FZ and the nearby HAZ suggest the highest CISCC-susceptible spots. The maximum tensile residual stresses were along the welding direction, indicating that if cracks occur, they would be perpendicular to the welding direction. This study involved developing and qualifying a SAW procedure for SNF canister production. The new procedure yielded cost savings (SAW working efficiency increased by about 80%), improved mechanical properties, and presented moderate residual stresses. Analysis revealed that the welded joint’s low-stress and high-stress damage assessments may be affected by shifts in the strain localization spot under loading.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Unconventional pressure-induced magnetic transitions and mechanical properties in non-magnetic LaFeSi

Here, this work demonstrates that two consecutive magnetic transitions occur in non-magnetic LaFeSi compound under negative hydrostatic pressure (small volume expansion). Electronic structure properties of LaFeSi were calculated using density functional theory (DFT) to understand the origin of these magnetic transitions. Mechanical properties of LaFeSi, especially elastic properties (shear and Young’s modulus, and Poisson’s ratio), were determined by DFT distortion calculations to elucidate lattice anisotropy and stability. The antiferromagnetic transition at –7.52 GPa, predicted in our work for LaFeSi, is consistent with the reported experimentally observed antiferromagnetic ground states in CeMnSi and LaMnSi compounds having similar crystal geometry. This finding of unexpected magnetic ordering predicts that layered non-magnetic materials, like LaFeSi, may become magnetically active with lattice expansion.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Developing Methods to Assess Changes in Mechanical Properties of Shale Modified by Engineered Mineral Precipitation

Fractures in subsurface shale formations serve multiple purposes, for example, in the recovery of resources in hydraulic fracturing or as potential harmful leakage passages through caprocks that may contribute undesired fluids to the atmosphere or functional groundwater aquifers. A proposed method to seal or influence fracture properties is Ureolysis-Induced Calcium Carbonate Precipitation (UICP), a bio-mineralization technology driven by the enzymatic hydrolysis of urea, resulting in the formation of calcium carbonate. Sporosarcina pasteurii is a common microbe used as the source of the urease enzyme that catalyzes the chemical reaction. The resulting calcium carbonate can bridge the gaps in fractured shale and reduce fluid flow through fractures. However, there is little information on how this process affects the mechanical properties of the resulting biomineralized shale. This study represents the first step toward determining the influence of UICP treatment on shale material and its subsequent mechanical strength properties. This methods development study aims to determine the effect that temperature has on the tensile strength of intact, unfractured shale cores (2.54 cm (1 in) diameter, 5.08 cm (2 in) long). Tensile strength was determined indirectly using a modified Brazilian test where the splitting tensile strength is attained by applying a compressive load onto the core. Shale cores from Eagle Ford and Wolfcamp formations were tested at both room temperature and 60°C to determine if increased temperature influences the tensile strength of the rock. This data will help to assess the necessity of testing biomineralized cores at temperature. Though 60°C may not mimic subsurface temperatures of the shales used in this study, it was chosen due to limitations of the UICP process while still approaching temperatures of shale formations. This project aims to evaluate what effect temperature has on the mechanical properties of intact shale cores so that engineered or natural rock fractures that are sealed by biomineralization can be better understood.

Bedey, Kayla↗
DOE OSTI2022

The effect of Ti content on age hardening and mechanical properties of uranium-titanium alloys

Here, the effect of Ti content on age hardening and the resulting mechanical properties are described for -quenched U-Ti alloys containing 0.3 wt.% to 2.0 wt.%Ti. Age hardening occurs between ~250°C and ~450°C. Overaging occurs at higher temperatures by cellular decomposition. Age hardening kinetics suggest that different mechanisms occur depending on Ti content and initial microstructure. Strengthening in 'a acicular martensites begins by the formation of Ti clusters which evolve into thin U 2 Ti disc shaped precipitates and later mature into continuous U 2 Ti rods beginning at peak hardness. The mechanism of hardening in 'b banded martensite is more elusive, as significant hardening occurs where atomic mobility is lower than that required for precipitate formation, similar to that reported for age hardening in ''b banded martensite in U-6%Nb. The activation energy for aging varies with Ti content and microstructure. In fully martensitic alloys containing 0.75% to 2.0%Ti it is in the vicinity of ~44 kcal/mole (184 kJ/mole). But it is lower in alloys containing less than 0.6%Ti where quenched microstructures are less than fully martensitic. Tensile ductility is high prior to aging, decreases with age hardening, is effectively zero at peak hardness, and remains low in overaged conditions. Attractive combinations of strength and ductility are best obtained in alloys containing 0.6% to 1.0%Ti which have been partially aged to fractional hardening levels no greater than ~0.6. This corresponds to the very early stages of aging, associated with clustering and the earliest stages of U 2 Ti disc formation. Alloys containing 0.45%Ti or less are not as responsive to age hardening. Alloys containing 1.5% and 2.0%Ti can be aged to higher strengths, but extreme quench rate sensitivity prevents them from being effectively heat treated in realistic section thicknesses.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of Ni content in Cu 1-x Ni x coating on microstructure evolution and mechanical properties of W/Mo joint via low-temperature diffusion bonding

The 93W and Mo1 refractory metals were bonded with different Cu 1- x Ni x coating interlayers of various Ni content using plasma-activated sintering at 700 °C. The effects of the Ni content in the Cu 1- x Ni x coating interlayer on the interfacial microstructure evolution and mechanical properties of the W/Mo joints were studied. The maximum average shear strength of the W/Mo joint was 316.5 MPa when the Ni content of the Cu 1- x Ni x coating interlayer was 25 %. When the Ni content of the Cu 1- x Ni x coating interlayer was below 50 %, the atomic diffusion at the W/Mo joint interface was adequate without the formation of intermetallic compounds, as demonstrated by the High Resolution Transmission Electron Microscope analyses of the joints. The presence of Ni in Cu 1- x Ni x promoted diffusion bonding at the interface, which contributed to the high mechanical properties of the W/Mo joint. With an increase in the Ni content of the Cu 1- x Ni x coating interlayer, the MoNi intermetallic compound (IMC) nucleated and grew at the Cu 1- x Ni x coating/Mo1 interface. When the Ni content of the Cu 1- x Ni x coating interlayer was above 50 %, the generation of a brittle MoNi IMC weakened the shear strength of the W/Mo joint dramatically.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Advanced Methodology and Preliminary Measurements of Molecular and Mechanical Properties of Heart Valves under Dynamic Strain

Mammalian heart valves are soft tissue assemblies with multi-scale material properties. This is because they are constructs comprising both muscle and non-contractile extracellular matrix proteins (such as collagens and proteoglycans) and transition regions where one form of tissue structure becomes another, significantly different form. The leaflets of the mitral and tricuspid valves are connected to chordae tendinae which, in turn, bind through papillary muscles to the cardiac wall of the ventricle. The transition regions between these tissue subsets are complex and diffuse. Their material composition and mechanical properties have not been previously described with both micro and nanoscopic data recorded simultaneously, as reported here. Annotating the mechanical characteristics of these tissue transitions will be of great value in developing novel implants, improving the state of the surgical simulators and advancing robot-assisted surgery. We present here developments in multi-scale methodology that produce data that can relate mechanical properties to molecular structure using scanning X-ray diffraction. We correlate these data to corresponding tissue level (macro and microscopic) stress and strain, with particular emphasis on the transition regions and present analyses to indicate points of possible failure in these tissues.

valve failure↗
DOE OSTI2020

Phase stability and mechanical properties of wire + arc additively manufactured H13 tool steel at elevated temperatures

Wire + arc additive manufacturing (WAAM) is considered an innovative technology that can change the manufacturing landscape in the near future. WAAM offers the benefits of inexpensive initial system setup and a high deposition rate for fabricating medium- and large-sized parts such as die-casting tools. Here, AISI H13 tool steel, a popular die-casting tool metal, is manufactured by cold metal transfer (CMT)-based WAAM and is then comprehensively analyzed for its microstructural and mechanical properties. Location-dependent phase combinations are observed, which could be explained by nonequilibrium thermal cycles that resulted from the layer-by-layer stacking mechanism used in WAAM. In addition, remelting and reheating of the layers reduces welding anomalies (e.g., pores and voids). The metallurgical characteristics of the H13 strongly correlate with the mechanical properties. The combinations of phases at different locations of the additively manufactured part exhibit a periodic microhardness profile. Martensite, Retained Austenite, Ferrite, and Carbide phases are found in combination at different locations of the part based on the part’s temperature distribution during additive deposition. Moreover, the tensile properties at elevated temperatures (23 °C, 300 °C, and 600 °C) are comparable to those from other WAAM and additive manufacturing (AM) processes. The X-ray diffraction results verify that the microstructural stability of the fabricated parts at high temperatures would allow them to be used in high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical Properties of Functionally Graded Concrete Lining for Deep Underground Structures

With the mining depth of coal resources increasing, the thickness of traditional lining for deep mines becomes large. The bearing capacity of the outer lining cannot be fully utilized, so a new type of functionally graded lining structure (FGL) with radial Young’s modulus varying in gradient is proposed. In this study, through theoretical analysis and numerical simulation, the mechanical properties of the functionally graded lining were studied, including the characteristics of the elastic working state and the ultimate bearing state. The influences of the structural parameters of the functionally graded lining, including the inner radius, the thickness, Young’s modulus, the compressive strength of the concrete, Poisson’s ratio, and the number of layers on the mechanical properties were analyzed. The calculation formula of the ultimate bearing capacity of the lining and the calculation formula of the maximum tangential strain at the time of lining failure were put forward. The accuracy of the formula was verified by comparing with the numerical simulation results. The research results provide the basis for the construction of the design theory of a functionally graded lining structure and have great engineering significance for the construction of the kilometer-deep mines in the future.

Li, De-Chun↗
DOE OSTI2024

Additive manufacturing of AISI M2 tool steel by binder jetting (BJ): Investigation of microstructural and mechanical properties

The presented research demonstrates for the first time the successful processing of AISI M2 tool steel by binder jetting, a promising additive manufacturing technique capable of producing complex shapes with minimal residual stresses and isotropic properties. The optimal printing parameters were explored by varying processing parameters such as the binder saturation (45 %–105 %), binder set time (0 to 10 s), targeted bed temperature (50–60 °C), oscillator (2600–2750 rpm), recoater (20–28 mm/s), and roller speeds (200–300 rpm). Microstructural characterization and evaluation of mechanical properties of binder jetted parts were performed using x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) to study their chemical composition, powder morphology, microstructure, carbide morphologies, relative density, hardness, compressive strength, and ductility. Two powder sizes (5 and 10 μm) were used, and sintering was performed at varying temperatures (1270, 1280, and 1300 °C) and durations (60 and 120 min), followed by a furnace, air, and water cooling. An optimum hardness of ~970 HV was obtained when parts were sintered at 1270 °C for 60 min, followed by water quenching. Impressive compressive strength of ~ 3580 MPa was observed in the sample sintered at 1280 °C for 60 min duration, followed by air cooling. Furnace-cooled parts showed the highest density of ~95 %, whereas the relative density of air- and water-cooled parts varied between ~91 to 93.50 %, respectively. The microstructure of sintered samples revealed the formation of M 6 C stable carbide, M 2 C metastable carbide, MC as a secondary carbide, and a-Fe matrix, which contributed to the observed increase in mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Impact of hydrogen bonding pendant groups in polymer grafted nanoparticles on interlayer adhesion and mechanical properties in material extrusion printing

The addition of nanoparticles or copolymer grafted nanoparticles (CPGNPs) to polymeric matrices greatly improves thermomechanical properties of the resulting nanocomposite, but corresponding studies of nanocomposite systems created by 3D printing are few, especially in the realm of functional polymeric materials. Here we describe how silica nanoparticle-grafted, random copolymers of poly(methyl methacrylate-random-2-uriedo-[1H]-pyrimidinone methacrylate) (P(MMA-r-UPyMA) dramatically increases the mechanical properties of poly(methyl methacrylate) (PMMA) based nanocomposite specimens created by melt extrusion printing. Most notably, when these novel CPGNPs are combined with PMMA matrix chains via a solution-based process, printed specimens containing only 0.5 wt% additive show significant increases in Young’s modulus (90%), storage modulus (93%), tensile modulus (148%) and ultimate tensile strength (110%). These improvements are ascribed to strengthening of adhesion across interfaces due to multi-point hydrogen bonding between UPyMA groups, the reinforcement effect of the P(MMA-r-UPyMA)-grafted silica nanoparticles, as well as hydrogen bonding interactions and entanglements between graft and matrix chains. Imaging of fracture surfaces after tensile testing reveals that in comparison to nanocomposites created by simple mechanical mixing of solids, the solution-casting process improves the dispersion of nanoparticles and reduces the void spaces between printed roads. These studies demonstrate that introducing functionality into polymer grafts, such as hydrogen bonding interactions, and intimate mixing of polymer-modified nanomaterials can greatly improve interlayer adhesion and mechanical properties, thereby advancing this method of polymer additive manufacturing

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of elastic mechanical properties of Tuscaloosa Marine Shale from well logs using the vertical transversely isotropic model

To avoid steep declines in the Tuscaloosa Marine Shale (TMS) production, wells are fracture-stimulated to release the hydrocarbons trapped in the matrix of the formation. An accurate estimation of Young’s modulus and Poisson’s ratio is essential for hydraulic fracture propagation. In addition, ignoring the highly heterogeneous and anisotropic character of TMS can lead to erroneous stress values, which subsequently affect hydraulic fracture width estimates and the overall hydraulic fracturing process. We have developed an empirical 1D geomechanical model that takes into account VTI anisotropy, and it is used to characterize the elastic mechanical properties of TMS in two wells. In the analyzed formation, the vertical Poisson’s ratio is less than the horizontal Poisson’s ratio, which suggests the necessity of an alternative to the ANNIE equations. The stiffness coefficients [Formula: see text] and [Formula: see text] were estimated using the relationships developed from the ultrasonic core data available for the two TMS. Further, correlations between the static and dynamic properties from laboratory tests were used to improve the minimum horizontal stress calculation. We compare VTI Young’s moduli, Poisson’s ratios, and minimum horizontal stress with the isotropic solution. VTI modeling improves the estimation of the elastic mechanical properties. The isotropic solution underestimates the minimum horizontal stress in the formation. Moreover, it was shown that the 20 ft shale interval below the TMS base is characterized by a low Young’s modulus (the vertical Young’s modulus is equal to 20 GPa, whereas the horizontal Young’s modulus is equal to 40 GPa) and may be a frac barrier.

Geochemistry & Geophysics↗
DOE OSTI2024

In Situ Prediction of Microstructure and Mechanical Properties in Laser-Remelted Al-Si Alloys: Towards Enhanced Additive Manufacturing

Laser surface remelting of aluminum alloys has emerged as a promising technique to enhance mechanical properties through refined microstructures. This process involves rapid cooling rates ranging from 10 3 to 10 8 °C/s, which increase solid solubility within aluminum alloys, shifting their eutectic composition to a larger value of silicon content. Consequently, the resulting microstructure combines a strengthened aluminum matrix with silicon fibers. This study focuses on the laser scanning of Al-Si aluminum alloy to reduce the size of aluminum matrix spacings and transform fibrous silicon particles from micrometer to nanometer dimensions. Analysis revealed that the eutectic structure contained 17.55% silicon by weight, surpassing the equilibrium eutectic composition of 12.6% silicon. Microstructure dimensions within the molten zones, termed ‘melt pools’, were extensively examined using Scanning Electron Microscopy (SEM) at intervals of approximately 20 μm from the surface. A notable increase in hardness, exceeding 50% compared to the base plate, was observed in the melt pool regions. Thus, it is exemplified that laser surface remelting introduces a novel strengthening mechanism in the alloy. Moreover, this study develops an in situ method for predicting melt pool properties and dimensions. A predictive model is proposed, correlating energy density and spectral signals emitted during laser remelting with mechanical properties and melt pool dimensions. This method significantly reduces characterization time from days to seconds, offering a streamlined approach for future studies in additive manufacturing.

36 MATERIALS SCIENCE↗