Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Low metal loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Solvent selection criteria for temperature-resilient lithium–sulfur batteries

All-climate temperature operation capability and increased energy density have been recognized as two crucial targets, but they are rarely achieved together in rechargeable lithium (Li) batteries. Herein, we demonstrate an electrolyte system by using monodentate dibutyl ether with both low melting and high boiling points as the sole solvent. Its weak solvation endows an aggregate solvation structure and low solubility toward polysulfide species in a relatively low electrolyte concentration (2 mol L −1 ). These features were found to be vital in avoiding dendrite growth and enabling Li metal Coulombic efficiencies of 99.0%, 98.2%, and 98.7% at 23 °C, −40 °C, and 50 °C, respectively. Pouch cells employing thin Li metal (50 μm) and high-loading sulfurized polyacrylonitrile (3.3 mAh cm −2 ) cathodes (negative-to-positive capacity ratio = 2) output 87.5% and 115.9% of their room temperature capacity at −40 °C and 50 °C, respectively. This work provides solvent-based design criteria for a wide temperature range Li-sulfur pouch cells.

25 ENERGY STORAGE↗
DOE OSTI2021

An Integrated High Pressure SOFC and Premixed Compression Ignition (PCI) Engine System

Components for a transformative, high pressure, intermediate temperature solid oxide fuel cell (SOFC) and premixed compression ignition (PCI) engine system were developed. The resulting system is a 1 MWe natural gas fueled hybrid SOFC and reciprocating internal combustion engine system capable of achieving over 70% electrical efficiency at a cost of $0.87/W. To achieve 70% electric efficiency, the SOFC system operates at 80% fuel utilization; however, when operating at this high level of fuel utilization, fuel to the engine (anode tailgas) is extremely dilute. Accordingly, a substantial portion of the effort focused on development and assessment of the combustion strategy capable of consuming this dilute fuel mixture. The engine testing effort showed that pre-chamber assisted compression ignition provides the best combination of controllability, efficiency and emissions. The engine experiments showed that high efficiency combustion can be achieved with near zero criteria pollutants. It is likely that the engine system could operate with minimal aftertreatment requirements, reducing complexity, cost, and precious metal usage. System level modeling was used to assess the overall efficiency, determine cost and efficiency tradeoffs, and demonstrate the potential to perform load following with the hybrid system. Finally, advanced manufacturing was used to demonstrate the potential to fabricate heat exchangers needed for the hybrid system from low chromium materials, which addresses the issue of chromium poisoning of the SOFC stack material.

03 NATURAL GAS↗
DOE OSTI2024

Local Electric Field Effects on Water Dissociation in Bipolar Membranes Studied Using Core–Shell Catalysts

The local electric field strength is thought to affect the rate of water dissociation (WD) in bipolar membranes (BPMs) at the catalyst–nanoparticle surfaces. Here, we study core–shell nanoparticles, where the core is metallic, semiconducting, or insulating, to understand this effect. The nanoparticle cores were coated with a WD catalyst layer (TiO2 or HfO2) via atomic layer deposition (ALD), and the morphology was imaged with transmission electron microscopy. Irrespective of the core material, these core–shell catalysts displayed comparable WD overpotentials at optimal mass loading, despite the hypothesized differences in the electric field strength across the catalyst particle suggested by continuum electrostatic simulations. Substantial atomic interdiffusion between the core and shell was ruled out by X-ray absorption spectroscopy, X-ray photoelectron spectroscopy, and diffuse reflectance optical measurements. However, the optimal mass loading of catalyst was roughly 1 order of magnitude higher for the conductive and high dielectric core materials than for the low dielectric insulating cores. These findings are consistent with the hypothesis that electric field screening within the core material focuses the electric field drop between particles such that larger film thicknesses can be tolerated. Collectively, these data support the idea that it is the local electric field at the molecular level that controls proton-transfer rates and that the metal core/dielectric-shell constructs introduced here modulate that field. Further materials and synthetic design may enable optimization of the electric field strength across the proton-transfer trajectory at the material surface.

Sarma, Prasad V↗
DOE OSTI2020

Novel Ionomers and electrode structures for improved PEMFC electrode performance at low PGM loadings (Final Report)

In this project, the objective is to develop new ORR electrocatalysts on optimized supports which can exceed all of the Department of Energy (DOE) 2020 targets listed in DE-FOA-0001412 directly relevant to the subtopic. This project’s approach is to develop novel, electrode-specific ionomers, and integrate them with state-of-the-art NSTF electrocatalyst powder to develop a cathode electrode achieving >= 044 A/mg PGM mass activity, <=30% mass activity loss during metal cycling, and <=0.125 g PGM /kW performance under DOE testing protocols. Ionomer O 2 permeability and proton conductivity will be increased by up to 1.5X over the baseline 3M800 perfluorosulfonate (PFSA) ionomer to enhance cathode electrode performance. Integration of cathode NSTF powder into an ionomer-containing electrode will increase the surface enhancement factor (SEF) to >=40 cm 2 PGM /cm 2 GEO allowing NSTF containing cathodes to exceed DOE MEA robustness targets. This report summarizes this project’s progress towards meeting the stated objectives and includes a summary of significant findings, conclusions, and developments over the entire project period from Oct. 1 st 2016 – Jan. 31 st 2020. This work has overcome key operation robustness issues with classic NSTF electrodes, identified pathways to improved dispersed and dispersed NSTF cathode performance, developed novel ionomers with high bulk conductivity and oxygen permeability, demonstrated exceptional support-independent electrode activity, and significantly increased metal and support stability through ionomer development. At this point, Tufts, MTU and all 5 FCPAD national labs have been involved, and contributed to, the improvements, learning and achievements of this work. Over the course of this project, more than 50 grams of dispersed NSTF powder in 15 different configurations have been generated, paving the way for scaleup within 3M. These whiskers have been processed in multiple ways, including acid leaching, powder-annealed, and sonicated by various means. For Task 2, 27 different types of ionomers were tested, 19 of which were made for the first time during the course of this project. 377 electrode inks with both NSTF and metal-on-carbon catalysts with I/C ratios from 0.2 to 1.2 were generated and mostly coated on a 3M pilot manufacturing line resulting in more than 700 different electrode types.

08 HYDROGEN↗
DOE OSTI2022

Mapping 3D grain and precipitate structure during in situ mechanical testing of open-cell metal foam using micro-computed tomography and high-energy X-ray diffraction microscopy

Open-cell metal foams are ultra-low-density cellular metals with complex hierarchical structures that span bulk, cell, ligament, and sub-ligament scales and give rise to desirable properties such as high strength-to-weight ratio and excellent energy absorption. Although literature suggests that intrinsic material structures at sub-ligament length scales (e.g., grains and precipitates) play an important role in mechanical behavior of open-cell metal foams, there are very few experimental measurements of such structures in three dimensions and for meaningful volumes of foam. This study seeks to map and track the three-dimensional (3D) grain and precipitate structures of an intact volume of open-cell aluminum foam by advancing microstructural characterization techniques that leverage X-ray micro-computed tomography (μCT) and far-field high-energy X-ray diffraction microscopy (FF-HEDM). A 6%-relative-density aluminum foam sample was mechanically tested in compression while μCT and FF-HEDM measurements were collected at interrupted loading states at beamline 1-ID of the Advanced Photon Source. Further, a new scanning strategy and reconstruction algorithm were established to enable characterization of a foam volume with diameter approximately four times wider than the nominal width of the X-ray beam. The result is a set of maps that detail both the 3D grain and precipitate structures throughout the foam volume at successive strain steps. A novel grain tracking procedure was developed to track individual grains within the foam volume by accounting for the large rigid-body motions that individual ligaments can undergo during mechanical loading. The ability to track grains and precipitate structures in three dimensions throughout large bulk deformation of ultra-low-density polycrystalline materials enables new possibilities for validating numerical models and investigating local failure mechanisms. Furthermore, the methods and procedures developed in this study could be applied to other ultra-low-density structures, such as additively manufactured lattices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Extreme fast charge aging: Correlation between electrode scale and heterogeneous degradation in Ni-rich layered cathodes

Extreme fast charging (XFC) is a key requirement for the adoption of battery-based electric vehicles by the transportation sector. However, XFC has been shown to accelerate degradation, causing the capacity, life, and safety of batteries to deteriorate. There are no systematic studies in the open literature regarding aging modes in Ni-rich Li y Ni 0.a Mn 0.b Co 0.c O 2 (NMCabc) cathodes caused by fast charging. Herein, we report the effects of cathode composition and electrode loading in pouch cells containing NMC532, 622 and 811 paired with graphite and cycled under XFC conditions. The relative anisotropic volume change in the unit cell increases with Ni content in low-loading cells, while it levels up for all three NMC cathodes in high-loading cells because of substantial Li plating. The amounts of lithium plating and heterogeneity on the anode, determined by crystallographic phase quantification, were found to be correlated with electrode loading and cathode heterogeneity. The concentrations of the transition metals deposited on the anodes depend on NMCabc composition in a complex way. More particle cracking and surface degradation was found in NMC811. Here, the findings in this work provide a new understanding of the failure mechanisms and their practical implications for compositional tuning of future high-Ni NMCabc cathode materials during fast charging.

25 ENERGY STORAGE↗
DOE OSTI2020

Atomic Layer Deposition Overcoating Improves Catalyst Selectivity and Longevity in Propane Dehydrogenation

Propylene, a precursor for commodity chemicals and plastics, is produced by propane dehydrogenation (PDH). An increase in PDH yield via added catalyst activity, lifetime, or selectivity represents significant energy and economic savings. Using Pt dispersed on Al2O3 extrudate supports as a commercially relevant model system, we demonstrate that atomic layer deposition (ALD) metal oxide overcoats, used to tailor metal-active sites, can increase PDH yield and selectivity. We investigate the interplay of Pt loading, ALD overcoat thickness, and Al 2 O 3 support surface area on PDH activity, selectivity, and catalyst stability to show that applying a 6-8 A thick layer of Al 2 O 3 on low-surface area Al 2 O 3 supports of similar to 90 m 2 /g surface area yields the optimal combination of stability and activity, while increasing propylene selectivity from 91 to 96%. Increased stability upon steaming deactivation occurs because the Al 2 O 3 overcoat prevents the Pt nanoparticles from sintering. We speculate that the ALD overcoat selectively binds to the undercoordinated sites on the Pt nanoparticles, while leaving the more selective terrace sites available for dehydrogenation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Recent Progress on Cerium Oxide‐Based Nanostructures for Energy and Environmental Applications

Cerium oxide (CeO 2 ) photo/electrocatalysts for energy storage and environmental applications have attracted considerable interest because of stable crystal structure, low toxicity/cost, superior chemical stability, stable redox (Ce 3+ /Ce 4+ ) pairs, abundant oxygen defects, and capablility for intense interaction with other materials. However, the wide bandgap and poor conductivity lower the CeO 2 photo/electrocatalytic and energy storage performances. To overcome these limitations, various modification strategies (tuning morphology, doping or loading of metal nanoparticles, and heterostructures) have been applied for the improvement of photocatalytic (removal of organic contaminants from water/wastewater and H 2 production and CO 2 reduction reactions) efficiency, electrocatalytic (hydrogen/oxygen evolution reactions and CO 2 reduction reactions), and energy storage performances (supercapacitor) of CeO 2 ‐based materials. Herein, the recent progress of CeO 2 ‐based materials for electro(photo)catalysis and energy storage applications has been discussed. The challenges and possible direction of CeO 2 ‐based materials for electro(photo)catalysis and energy storage applications have been emphasized. Furthermore, this comprehensive review is expected to advance the design of CeO 2 ‐based materials and their applications in electro(photo)catalysis and energy.

Ray, Schindra Kumar [Department of Chemistry North↗
DOE OSTI2024

Fuel Cell Membrane Electrode Assemblies with Ultra-Low Pt Nanofiber Electrodes (Final Report)

H 2 /air fuel cell membrane-electrode-assemblies (MEAs) were fabricated with electrospun particle/polymer nanofiber mat cathodes (0.1 mg Pt /cm 2 or 0.2 mg Pt /cm 2 Pt/C, PtCo/C or PtNi/C) and anodes (0.1 mg/cm 2 Pt/C), where the binder was a mixture of acid-form perfluorosulfonic acid ionomer (e.g., Nafion™) and poly(acrylic acid) (PAA) carrier polymer or sodium-form PFSA with a carrier polymer of either PAA or polyethylene oxide (PEO). For the latter two cases, the water-soluble carrier was removed from the fibers after electrospinning. MEAs with Pt/C anode/cathode catalyst loadings of 0.1 mg Pt /cm2 each, an 1100 EW PFSA binder (Nafion™ dispersion), and a Nafion 211 membrane produced high power at both high and low relative humidity (RH) conditions, e.g., a maximum power density of 919 mW/cm 2 at 100% RH and 832 mW/cm 2 at 40% RH for a test at 80 °C and 200 kPa abs . The high power at low RH was attributed to nm-size pores within the fibers that trap water via capillary condensation thus maintaining a high proton conductivity of the PFSA binder in the cathode and especially the anode while minimizing/eliminating ionic isolation of catalyst particles in low water content, poorly conductive binder. At the same time, micro-porosity between fibers in the cathode allows for fast removal of electrogenerated water, thus minimizing cathode flooding. Nanofiber MEAs with Pt alloy catalyst cathodes also performed well, where a fibrous PtCo/C catalyst cathode at a loading of 0.1 mg/cm 2 produced 20% more power than a conventional powder cathode MEA, e.g., a maximum power density of 1,045 mW/cm 2 vs. 869 mW/cm 2 at 80 °C, 100% RH, and 200 kPa abs , and a PtNi/C fiber cathode MEAs prepared with Na+-form Nafion + PEO generated a maximum power of 820 mW/cm 2 at 40% RH. Fiber electrode MEAs with a neat Nafion binder (prepared from Na+-form Nafion + PEO or PAA) where the cathode Pt loading was ~0.1 mg/cm 2 exhibited a 25% loss in maximum power at 30,000 metal dissolution cycles, as compared to a 12% loss when the cathode binder was H+-form Nafion + PAA. The performance of a fiber mat electrode MEA with Pt/C catalyst (0.2 mg/cm 2 cathode loading and 0.1 mg/cm 2 anode loading) was excellent. At 80 oC and 200 kPa abs , the maximum power density was 1104 mW/cm 2 . The maximum power was independent of feed gas humidity for 40 < RH < 100%. The power loss after a metal dissolution AST (30,000 voltage cycles) was only 13%.

08 HYDROGEN↗
DOE OSTI2025

Lithium‐Containing Hybrid SEI Layer Enabling High Mass Loading and Anode‐Less Sodium Metal Batteries

Abstract The continuous rupturing and rebuilding of unstable solid electrolyte interphase (SEI) layer during cycling would block Na + diffusion and induce Na dendrite formation, ultimately limiting the practical application of high‐energy‐density sodium metal batteries. Herein, a hybrid SEI layer containing Li‐species is dexterously constructed on the surface of sodium metal anode. Li‐containing inorganic components (Li 3 N, LiF, and Li 2 CO 3 ) are introduced to stabilize the Na/electrolyte interface and enhance the mechanical and diffusion kinetic properties of the SEI layer, which can reduce the side reactions and gas generation, regulate Na + flux during cycling and promote rapid Na + migration for uniform dendrite‐free Na deposition. As a result, the constructed Na symmetric cells achieve low overpotential and long cycle life of 5900, 1800, and 500 h at current densities of 3, 10, and 30 mA cm −2 , respectively. Furthermore, the full cells paired with the Na₃V₂(PO₄)₃ cathode demonstrate high specific capacity and excellent cycle stability, even at an ultra‐high cathode loading of 39.3 mg cm −2 and a low N/P ratio (negative/positive electrode capacity ratio of 1.21).

Xia, Li [State Key Laboratory of Physical Chemistr↗
DOE OSTI2020

Low‐PGM and PGM‐Free Catalysts for Proton Exchange Membrane Fuel Cells: Stability Challenges and Material Solutions

Abstract Fuel cells as an attractive clean energy technology have recently regained popularity in academia, government, and industry. In a mainstream proton exchange membrane (PEM) fuel cell, platinum‐group‐metal (PGM)‐based catalysts account for ≈50% of the projected total cost for large‐scale production. To lower the cost, two materials‐based strategies have been pursued: 1) to decrease PGM catalyst usage (so‐called low‐PGM catalysts), and 2) to develop alternative PGM‐free catalysts. Grand stability challenges exist when PGM catalyst loading is decreased in a membrane electrode assembly (MEA)—the power generation unit of a PEM fuel cell—or when PGM‐free catalysts are integrated into an MEA. More importantly, there is a significant knowledge gap between materials innovation and device integration. For example, high‐performance electrocatalysts usually demonstrate undesired quick degradation in MEAs. This issue significantly limits the development of PEM fuel cells. Herein, recent progress in understanding the degradation of low‐PGM and PGM‐free catalysts in fuel cell MEAs and materials‐based solutions to address these issues are reviewed. The key factors that degrade the MEA performance are highlighted. Innovative, emerging material concepts and development of low‐PGM and PGM‐free catalysts are discussed.

Du, Lei↗
DOE OSTI2021

Catalytic membrane reactor, methods of making the same and methods of using the same for dehydrogenation reactions

A catalytic membrane reactor and methods of operating and producing the same are provided that efficiently produces highly pure hydrogen (H2) from ammonia (NH3) as well as operates according to other chemical conversion processes. In one embodiment, a tubular ceramic support made from porous yttria-stabilized zirconia has an outer surface that is impregnated with a metal catalyst such as ruthenium and then plated with a hydrogen permeable membrane such as palladium. An inner surface of the ceramic support is impregnated with cesium to promote conversion of ammonia to hydrogen and nitrogen (N2). The resulting catalytic membrane reactor produces highly pure hydrogen at low temperatures and with less catalytic loading. Therefore, ammonia can be used to effectively transport hydrogen for use in, for example, fuel cells in a vehicle.

Way, James Douglas↗
DOE OSTI2023

An inorganic-rich but LiF-free interphase for fast charging and long cycle life lithium metal batteries

Abstract Li metal batteries using Li metal as negative electrode and LiNi 1-x-y Mn x Co y O 2 as positive electrode represent the next generation high-energy batteries. A major challenge facing these batteries is finding electrolytes capable of forming good interphases. Conventionally, electrolyte is fluorinated to generate anion-derived LiF-rich interphases. However, their low ionic conductivities forbid fast-charging. Here, we use CsNO 3 as a dual-functional additive to form stable interphases on both electrodes. Such strategy allows the use of 1,2-dimethoxyethane as the single solvent, promising superior ion transport and fast charging. LiNi 1-x-y Mn x Co y O 2 is protected by the nitrate-derived species. On the Li metal side, large Cs + has weak interactions with the solvent, leading to presence of anions in the solvation sheath and an anion-derived interphase. The interphase is surprisingly dominated by cesium bis(fluorosulfonyl)imide, a component not reported before. Its presence suggests that Cs + is doing more than just electrostatic shielding as commonly believed. The interphase is free of LiF but still promises high performance as cells with high LiNi 0.8 Mn 0.1 Co 0.1 O 2 loading (21 mg/cm 2 ) and low N/P ratio (~2) can be cycled at 2C (~8 mA/cm 2 ) with above 80% capacity retention after 200 cycles. These results suggest the role of LiF and Cs-containing additives need to be revisited.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Atomically dispersed Pt and Fe sites and Pt–Fe nanoparticles for durable proton exchange membrane fuel cells

Proton exchange membrane fuel cells convert hydrogen and oxygen into electricity without emissions. The high cost and low durability of Pt-based electrocatalysts for the oxygen reduction reaction hinder their wide application, and the development of non-precious metal electrocatalysts is limited by their low performance. Here we design a hybrid electrocatalyst that consists of atomically dispersed Pt and Fe single atoms and Pt–Fe alloy nanoparticles. Its Pt mass activity is 3.7 times higher than that of commercial Pt/C in a fuel cell. More importantly, the fuel cell with a low Pt loading in the cathode (0.015 mg Pt cm –2 ) shows an excellent durability, with a 97% activity retention after 100,000 cycles and no noticeable current drop at 0.6 V for over 200 hours. These results highlight the importance of the synergistic effects among active sites in hybrid electrocatalysts and provide an alternative way to design more active and durable low-Pt electrocatalysts for electrochemical devices.

25 ENERGY STORAGE↗
DOE OSTI2023

Stationary Direct Methanol Fuel Cells Using Pure Methanol

This project developed stationary direct methanol fuel cells (DMFCs) using pure methanol as the fuel, integrating complementary institutional expertise on platinum group metals free (PGM-free) cathode catalyst (UB), supported anode catalysts (KSU), electrode fabrication, characterization, and optimization (CMU), and multi-phase mass transfer (KU). The proposed cost-effective prototype will deliver reliable and durable performance using a methanol-tolerant PGM-free cathode and a high-performance anode with low PtRu loading. At the end of the project, the research team is expected to deliver a single cell (50 cm 2 ) with ≤3 mg PGM /cm 2 that achieves 300 mW/cm 2 using pure methanol.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Experimental Procedure and Results for Contact Thermal Conductance Measurements performed during FY 2021

Weapons Test Engineering groups at LANL are responsible for testing and simulating weapon assemblies and subassemblies in support of qualification and certification of nuclear weapon systems. The complex nature of the assemblies themselves coupled with the loading environments, gives rise to low confidence and high uncertainties in the interpretation of both experimental and simulated results. In an effort to reduce these uncertainties, a project was started at LANL to perform focused and systematic experiments combined with simulations to increase confidence in both arenas. A key goal of the work performed under the Delivery Environments (DE) Testbeds to Reduce Uncertainties in Simulations and Tests TRUST program, focuses on identifying and minimizing sources of uncertainty associated with experimental and computational techniques. Specifically, with the above as motivation, a measurement procedure was developed by MST-8 to perform thermal conductivity measurements on cylinders of both similar and dissimilar metallic systems as a function of loading conditions and varying material interface morphologies between these components.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Surface-Initiated Atom Transfer Radical Polymerization Using Hydrogel Reactors

Atom transfer radical polymerization (ATRP) is a controlled radical polymerization method that enables the synthesis of tailored polymeric materials with low dispersity, highlighting its immense potential for green fabrication of advanced materials. However, its broader implementation is limited by challenges in product isolation, maintaining catalyst activity, and mitigating atmospheric sensitivity arising from oxygen-sensitive metal catalysts. Here, gelatin hydrogels (GHs) are introduced as a soft “reactor” matrix for interfacial ATRP, operating with minimal metal-catalyst loading while exhibiting possibly an organoreductive behavior. This strategy leverages activator regeneration via electron transfer through a ligand–metal charge-transfer (LMCT) mechanism to reduce oxidized metal catalysts within the GH network. Polymerization is evaluated by growing polymer brushes at an active interface formed between GHs swollen in monomer solution and an initiating surface, and sequential growth experiments confirmed that GH-mediated ATRP preserves living character. Under UV illumination, LMCT is activated, producing polymers both at the desired interface and within the GH bulk. UV–Vis spectroscopy revealed active reduction of Cu(II) to Cu(I) along with concentration-dependent complex formation, indicating dynamic coordination chemistry within the hydrogel. The redox-active arginine- and glutamic acid-rich gelatin backbone coordinates and reduces the metal center, enabling ATRP at ppm-level catalyst concentrations. While polymerization proceeds in GH-Cu(II) reactors, adding external mobile ligands to the GH results in longer polymer brushes. Here, the results reported here are exploratory. More experiments are needed to characterize polymer brush growth in GHs and compare it to conventional surface-initiated polymerization in solution.

Absorption↗
DOE OSTI2023

Editorial: Advanced water splitting technologies development: Best practices and protocols

As the level of deployment and utilization of renewable energy sources, including wind and solar, continues to rise, large-scale, long-term energy storage technologies that could accommodate weekly and seasonal energy fluctuations will play a significant role in the overall deployment of renewable energies in the future. Harnessing and storing renewable energy resources via electrochemical, photoelectrochemical, or thermochemical processes by converting renewable energy into sustainable (energy storage) fuels have the potential to meet the long-term, terawatt scale energy storage challenge. Renewable hydrogen production is the cornerstone for sustainable fuel production and deep decarbonization of multiple sectors in our society. Cost-competitive clean hydrogen provides value to applications, such as 1) in the transportation sector for fuel cell vehicles, 2) in the electric grid sector for system stability and load balancing, and 3) in the industrial sector with metal refineries, cement production, and biomass upgrading (carbon-free fertilizer production). In addition, coupling clean renewable hydrogen with the carbon and nitrogen cycles enables known and well-established thermal-chemical processes to generate renewable hydrocarbon fuels and ammonia. The Advanced Water Splitting Technologies (AWST): low temperature electrolysis (LTE), high temperature electrolysis (HTE), photoelectrochemical (PEC) and solar thermo-chemical hydrogen (STCH) provide four unique and parallel approaches to produce low cost, low greenhouse gas (GHG) emission hydrogen at scale (Figure 1). Cost competitive clean hydrogen production using these four technologies is a current high priority focus for governments and industry. In June of 2022, the U.S. Department of Energy (DOE) launched the first in a series of Earthshot Initiatives. The Hydrogen Shot, “1 1 1” aims to reduce the cost of clean hydrogen by more than 80% to one dollar per one kilogram in 1 decade ($\$$1/kg H 2 ). The European Green Deal and the International Energy Agency (IEA) have implemented a strong focus on green hydrogen production for a clean and secure energy future.

benchmarking, low temperature electrolysis↗