Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “KSi”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Cryogenic Properties of a New Tough-Strong Iron Alloy

A program was undertaken to develop an iron-base alloy having a fracture toughness of 220 MPa. m superscript 1/2 with a corresponding yield stress of 1.4 GPa (200 ksi) at-196 C. An Fe-12Ni alloy was selected as the base alloy. Factors considered included reactive metal additions, effects of interstitial impurities, strengthening mechanisms, and weldability. The goals were met in an Fe-12Ni-0.5Al alloy strengthened by thermomechanical processing or by precipitate strengthening with 2 percent Cu. The alloy is weldable with the weld metal and heat affected zone in the postweld annealed condition having toughness equivalent to the base alloy.

Stephens, J. R.↗
NASA NTRS1977

Correlation of creep rate with microstructural changes during high temperature creep

Creep tests were conducted on Haynes 188 cobalt-base alloy and alpha titanium. The tests on Haynes 188 were conducted at 1600 F and 1800 F for stresses from 3 to 20 ksi, and the as-received, mill-annealed results were compared to specimens given 5%, 10%, and 15% room temperature prestrains and then annealed one hour at 1800 F. The tests on alpha titanium were performed at 7,250 and 10,000 psi at 500 C. One creep test was done at 527 C and 10,000 psi to provide information on kinetics. Results for annealed titanium were compared to specimens given 10% and 20% room temperature prestrains followed by 100 hours recovery at 550 C. Electron microscopy was used to relate dislocation and precipitate structure to the creep behavior of the two materials. The results on Haynes 188 alloy reveal that the time to reach 0.5% creep strain at 1600 F increases with increasing prestrain for exposure times less than 1,000 hours, the increase at 15% prestrain being more than a factor of ten.

Young, C. T.↗
NASA NTRS1977

Techniques for increasing boron fiber fracture strain

Improvement in the strain-to-failure of chemical-vapor-deposition boron fibers is shown possible by contracting the tungsten boride core region and its inherent flaws. Results of three methods are presented in which etching and thermal-processing techniques were employed to achieve core flaw contraction by internal stresses available in the boron sheath. After commercially and treatment-induced surface flaws were removed from 203-micron (8-mil) fibers, the core flaw was observed to be essentially the only source of fiber fracture. Thus, fiber strain-to-failure was found to improve by an amount equal to the treatment-induced contraction on the core flaw. To date, average fracture strains and stresses greater than 1.4% and 5.5 GN/sq m (800 ksi), respectively, have been achieved. Commercial feasibility considerations suggest as the most cost-effective technique that method in which as-produced fibers are given a rapid heat treatment above 700 C. Preliminary results concerning the contraction kinetics and fracture behavior observed with this technique are presented and discussed for both high-vacuum and argon-gas heat-treatment environments.

Dicarlo, J. A.↗
NASA NTRS1978

Rolling element fatigue testing of gear materials

Rolling element fatigue lives of nine alloys were evaluated in Rolling Contact (RC) rigs. Test conditions included a Hertzian stress at 4,826 MPa (700 ksi), a rolling speed of 6.23 m/sec (245 in/sec.). Tests were run with a Type I oil (MIL-L-7808G) at room temperature. B-10 lives (10% failure rate) of alloys were compared versus reference alloys, VIM-VAR AISI M-50 and VAR AISI 9310. Six case carburizing alloys (AISI 9310, CBS600, CBS1000M, EX00014, Vasco X-2 and EX00053) and three through-hardening alloys (AISI M-50, VascoMax 350 and Vasco Matrix 2 evaluated, showed RCF performance inferior or equivalent to that of AISI 9310 and AISI M-50. It was also found that the effects of vacuum melting processes, different tempering temperatures, freezing cycle during heat treating, shot peening, gold plating and chrome plating employed in the present investigation did not significantly affect RCF life.

Nahm, A. H.↗
NASA NTRS1977

Cryogenic properties of a new tough-strong iron alloy

A program was undertaken to develop an iron-base alloy having a fracture toughness of 220 MPa-sq root meters with a corresponding yield stress of 1.4 GPa (200 ksi) at -196 C. An Fe-12Ni alloy was selected as the base alloy. Factors considered include reactive metal additions, effects of interstitial impurities, strengthening mechanisms, and weldability. The goals of this program were met in an Fe-12Ni-0.5Al alloy strengthened by thermomechanical processing or by precipitate strengthening with 2 percent Cu. The alloy is weldable with the weld metal and heat affected zone in the post-weld annealed condition having toughness equivalent to the base alloy.

Stephens, J. R.↗
NASA NTRS1977

Strength enhancement process for prealloyed powder superalloys

A technique involving superplastic processing and high-pressure autoclaving was applied to a nickel-base prealloyed powder alloy. Tensile strengths as high as 2865 MN/sq m (415 ksi) at 480 C (900 F) were obtained with as-superplastically deformed material. Appropriate treatments yielding materials with high-temperature tensile and stress-rupture strengths (980 C (1800 F)) were also devised.

Waters, W. J.↗
NASA NTRS1978

Space Shuttle SRM metal case component fabrication

The 146 in. diam metal case components of the Space Shuttle Solid Rocket Motor (SRM) being developed have been successfully static-tested. The limitations placed on the program included current practice and facilities at the steel mills, forging suppliers, heat treaters, and machining operations. In addition, Thiokol had not previously fabricated metal components of this size with a minimum fracture toughness of 90 ksi-in. to 1/2 power. To insure that the SRM was producible within the established guidelines, it was necessary to coordinate all data heat by heat, forging by forging, and heat treat run by heat treat run. The basic fabrication sequences are outlined, and the data from the heat treat programs are presented.

Krummel, C. H.↗
NASA NTRS1980

Evaluation and prediction of long term space environmental effects on non-metallic materials

The effects of prolonged spacecraft materials were determined and the results compared with predicted behavior. The adhesion and dielectric properties of poly-thermaleze and therm-amid magnet wire insulation were studied. The tensile properties of Lexan, polyurethane, polyethelyne, lucite, and nylon were studied well as the flexure and tensile characteristic of Adlock 851, a phenolic laminate. The volume resistivity of Cho-seal, a conductive elastomer was also a examined. Tables show the time exposed at thermal vacuum, and the high, low, and average MPA and KSI.

Shepic, J. A.↗
NASA NTRS1980

Development of exothermically cast single-crystal Mar-M 247 and derivative alloys

A low-cost, exothermic directional-solidification (DS) process was developed to produce single-crystal (SC) Mar-M 247 high-pressure turbine blades. Stress-rupture data indicated that SC Mar-M 247 provides only marginal improvements in longitudinal strength relative to the columnar grained DS material. Removal of grain boundary strengthening elements (B, C, Zr, Hf) from the Mar-M 247 composition (which are also melting point depressants) permitted the alloy to be solutioned at significantly higher temperatures. An order of magnitude improvement in rupture life relative to SC Mar-M 247 was observed for several derivative alloys at 103.5 MPa (15 KSI) and 1093 C. Rupture lives of the modified SC alloys were significantly affected by both alloy purity and heat treatment. Critical aspects of vacuum induction refining, exothermic casting technology, alloy development and heat treatment, which contributed to this new class of turbine blades, are reviewed

Strangman, T. E.↗
NASA NTRS1981

Low strain creep and aging of aluminum alloy 2219-T87 sheet

The constant load creep and isothermal aging characteristics of aluminum alloy 2219-T87 sheet have been studied experimentally and analytically in the temperature range 250 to 650 F at stress levels between 2.9 and 4.0 ksi (20 to 283 MPa). Testing variables were closely and automatically monitored. The data generated agree somewhat with the literature data base at lower temperatures, but above 500 F, discrepancies of greater than an order of magnitude in the time to 1% creep strain occur. Good correlation was found with the Larson-Miller parameter as modeled by a second-order polynomial in stress. Constitutive equations for time to 0.1%, 0.2%, 0.5%, and 1.0% creep are given. Information on residual mechanical properties and electrical conductivity is also provided.

Navrotski, G.↗
NASA NTRS1981

Oxidation-induced contraction and strengthening of boron fibers

An investigation of the physical and mechanical effects of thermal treatment in a controlled oxygen-argon atmosphere on boron fibers is reported, with attention to the optimization of such treatment as a secondary processing method for improvement of fiber strength. The strengthening mechanism is comprised of an oxidation-induced axial contraction of the fiber, accompanied by axial compression of strength-limiting flaws within the fiber's tungsten boride core. It was found that after an oxidation contraction of 0.3% near 900 C, and a slight surface etch near 100 C, the average tensile strength of 203-micron fibers increased from 500 to 800 ksi. Various physical observations are used to develop mechanistic models of oxidation, contraction, and the formation of new flaws in the boron sheath at contractions greater than 0.3%.

Dicarlo, J. A.↗
NASA NTRS1981

Development of low modulus material for use in ceramic gas path seal applications

Three candidate materials were examined: Brunsbond (R) Pad; plasma sprayed porous NiCrAlY; and plasma sprayed low modulus microcracked zirconia. Evaluation consisted of mechanical, thermophysical, and oxidation resistance testing along with optical microscopy and a feasibility demonstration of attaching the material to a suitable substrate. The goals of the program were the following: feasibility of fastening or depositing the low modulus system onto a broad range of substrate alloys; feasibility of depositing or forming the low modulus system to a thickness of 0.19 cm to 0.38 cm; potential to attain a modulus of elasticity in the range of 3.4 to 6.9 GPa (0.5 to 1.0 MSI), and an ultimate strength of 17.2 MPa (2.5 ksi); suitable thermal conductivity; and static oxidation life of at least 1000 hours at 1311 K. The results of the program indicate that all three systems offer attractive properties as a strain isolator material.

Eaton, H. E.↗
NASA NTRS1982

Net shape fabrication of Alpha Silicon Carbide turbine components

Development of Alpha Silicon Carbide components by net shape fabrication techniques has continued in conjunction with several turbine engine programs. Progress in injection molding of simple parts has been extended to much larger components. Turbine rotors fabricated by a one piece molding have been successfully spin tested above design speeds. Static components weighing up to 4.5 kg and 33 cc in diameter have also been produced using this technique. Use of sintering fixtures significantly improves dimensional control. A new Si-SiC composite material has also been developed with average strengths up to 1000 MPa (150 ksi) at 1200 C.

Storm, R. S.↗
NASA NTRS1980

Cast Fe-base cylinder/regenerator housing alloy

The development of an iron-base alloy that can meet the requirements of automotive Stirling engine cylinders and regenerator housings is described. Alloy requirements are as follows: a cast alloy, stress for 5000-hr rupture life of 200 MPa (29 ksi) at 775 C (1427 F), oxidation/corrosion resistance comparable to that of N-155, compatibility with hydrogen, and an alloy cost less than or equal to that of 19-9DL. The preliminary screening and evaluation of ten alloys are described.

Larson, F.↗
NASA NTRS1983

Development of tough, strong, iron-base alloy for cryogenic applications

The development of an iron-base alloy that combines the normally divergent properties of high toughness and high strength at cryogenic temperatures is discussed. Specifically, alloy properties were sought which at -196 C would exhibit a fracture toughness of 220 MPa-m(1/2) with a corresponding yield strength of 1.4 GPa (200 ksi). Early work showed that high toughness could be achieved in Fe-12Ni alloys containing reactive metal additions such as Al, Nb, Ti, and V. Further research emphasized strengthening of these tough alloys by thermomechanical processing and the addition of Cu. Results showed that high strength and high toughness could be achieved in a single alloy at temperatures as low as -196 C. An alloy with composition Fe-12Ni-9.5Al-2Cu exhibited a yield strength of 1.65 GPa with a corresponding fracture toughness of 220 MPa-m(1/2) at -196 C. Strengthening due to Cu additions to the Fe-12Ni base alloys results primarily from precipitation of Cu-rich epsilon particles approximately 20 nm in diameter. Strengthening mechanisms are discussed in terms of an elastic modulus hardening model and are supported by transimission electron microscopy examinations of selected test specimens.

Stephens, J. R.↗
NASA NTRS1983

Low-cost single-crystal turbine blades, volume 1

The exothermic casting process was successfully developed into a low cost nonproprietary method for producing single crystal (SC) castings. Casting yields were lower than expected, on the order of 20 percent, but it is felt that the casting yield could be significantly improved with minor modifications to the process. Single crystal Mar-M 247 and two derivative SC alloys were developed. NASAIR 100 and SC Alloy 3 were fully characterized through mechanical property testing. SC Mar-M 247 shows no significant improvement in strength over directionally solidified (DS) Mar-M 247, but the derivative alloys, NASAIR 100 and Alloy 3, show significant tensile and fatigue improvements. The 1000 hr/238 MPa (20 ksi) stress rupture capability compared to DS Mar-M 247 was improved over 28 C. Firtree testing, holography, and strain gauge rig testing were used to evaluate the effects of the anisotropic characteristics of single crystal materials. In general, the single crystal material behaved similarly to DS Mar-M 247. Two complete engine sets of SC HP turbine blades were cast using the exothermic casting process and fully machined.

Strangman, T. E.↗
NASA NTRS1984

Grain-refining heat treatments to improve cryogenic toughness of high-strength steels

The development of two high Reynolds number wind tunnels at NASA Langley Research Center which operate at cryogenic temperatures with high dynamic pressures has imposed severe requirements on materials for model construction. Existing commercial high strength steels lack sufficient toughness to permit their safe use at temperatures approaching that of liquid nitrogen (-320 F). Therefore, a program to improve the cryogenic toughness of commercial high strength steels was conducted. Significant improvement in the cryogenic toughness of commercial high strength martensitic and maraging steels was demonstrated through the use of grain refining heat treatments. Charpy impact strength at -320 F was increased by 50 to 180 percent for the various alloys without significant loss in tensile strength. The grain sizes of the 9 percent Ni-Co alloys and 200 grade maraging steels were reduced to 1/10 of the original size or smaller, with the added benefit of improved machinability. This grain refining technique should permit these alloys with ultimate strengths of 220 to 270 ksi to receive consideration for cryogenic service.

Rush, H. F.↗
NASA NTRS1985

The Strength and Characteristics of VPPA Welded 2219-T87 Aluminum Alloy

A study of the variable polarity plasma arc (VPPA) welding process and those factors that control the structure and properties of VPPA welded aluminum alloy 2219-T87 was conducted. The importance of joint preparation, alignment of parts and welding process variables are already established. Internal weld defects have been eliminated. However, a variation of properties was found to be due to the size variation of interdendritic particles in the fusion zone. These particles contribute to the void formation process, which controls the ultimate tensile strength of the welded alloy. A variation of 150 microns in particle size correlated with a 10 ksi variation of ultimate tensile strength. It was found that all fracture surfaces were of the dimple rupture type, with fracture initiating within the fusion zone.

Jemian, W. A.↗