SEARCH · Engineering Papers

Results for “KCl”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Strong Enhancement of Nanoconfined Water Mobility by a Structure Breaking Salt

For the majority of the water present on earth, the two most important factors influencing its behavior are confinement, in either inorganic or organic matrixes, and the presence of solutes. Here, we investigate the effect of confinement in 3 nm pores on water diffusivity in aqueous solutions with archetypical solutes, a structure making (kosmotrope) NaCl and a structure breaking (chaotrope) KCl, up to 1.0 M in concentration. The water diffusivity in bulk aqueous solutions in such a concentration range is known to decrease very slightly in the presence of NaCl and increase very slightly in the presence of KCl. However, here we observe the water diffusivity in confined H 2 O–KCl increases by a factor of 2 compared to the pure water diffusivity in the same confinement. This unusually strong cumulative effect of confinement and a structure breaking additive may have profound implications for the mobility and transport of aqueous species in nature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Electrostatic Gating of Ionic Conductance through Heterogeneous van der Waals Nanopores

Nanofluidic ionic transistors typically require gate voltages above 1 V and operate only at submillimolar ionic strengths, limiting their biocompatible applications. We demonstrate ionic transistors consisting of single sub-10 nm nanopores drilled in van der Waals (vdW) heterostructures with internal gate electrodes made of few-layer graphene. These devices deliver up to 10-fold current modulation at gate voltages as low as 0.3 V in 10 mM KCl, and ∼2-fold modulation at near-physiological 100 mM KCl. Baseline conductance with no gate shows surface-charge-dominated transport below 100 mM KCl, consistent with negatively charged hBN walls and ∼5 nm opening of the pores. The surface charge and the electrochemical asymmetry introduced by the three-electrode configuration govern the device’s behavior: negative gate voltage (V G ) enriches ionic concentrations and enhances current, whereas positive V G induces a local depletion zone that suppresses transport. The current modulation by V G is dependent on the polarity of the transmembrane potential and leads to ion current rectification. Molecular dynamics simulations of a nanopore in a hBN–graphene–hBN stack reveal confinement and surface charge-dependent suppression of the relative permittivity of interfacial water. Continuum modeling with radially varying interfacial water permittivity reproduces the asymmetric I–V characteristics and explains how the embedded gate sculpts local potential and ion concentrations. By enabling sub-0.5 V control of ionic transport at up to 100 mM salt concentrations, these devices address a key need in nanofluidics to create low-power ionic circuits and biosensing.

Materials science↗

DOE OSTI2023

AL4GAP: Active learning workflow for generating DFT-SCAN accurate machine-learning potentials for combinatorial molten salt mixtures

Machine learning interatomic potentials have emerged as a powerful tool for bypassing the spatiotemporal limitations of ab initio simulations, but major challenges remain in their efficient parameterization. We present AL4GAP, an ensemble active learning software workflow for generating multicomposition Gaussian approximation potentials (GAP) for arbitrary molten salt mixtures. The workflow capabilities include: (1) setting up user-defined combinatorial chemical spaces of charge neutral mixtures of arbitrary molten mixtures spanning 11 cations (Li, Na, K, Rb, Cs, Mg, Ca, Sr, Ba and two heavy species, Nd, and Th) and 4 anions (F, Cl, Br, and I), (2) configurational sampling using low-cost empirical parameterizations, (3) active learning for down-selecting configurational samples for single point density functional theory calculations at the level of Strongly Constrained and Appropriately Normed (SCAN) exchange-correlation functional, and (4) Bayesian optimization for hyperparameter tuning of two-body and many-body GAP models. Here, we apply the AL4GAP workflow to showcase high throughput generation of five independent GAP models for multicomposition binary-mixture melts, each of increasing complexity with respect to charge valency and electronic structure, namely: LiCl–KCl, NaCl–CaCl 2 , KCl–NdCl 3 , CaCl 2 –NdCl 3 , and KCl–ThCl 4 . Our results indicate that GAP models can accurately predict structure for diverse molten salt mixture with density functional theory (DFT)-SCAN accuracy, capturing the intermediate range ordering characteristic of the multivalent cationic melts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Experimental Study of Eutectic Molten Salts NaCl/KCl/ZnCl2 Heat Transfer Inside a Smooth Tube for High-Temperature Application

Abstract Eutectic salts NaCl-KCl-ZnCl2 and NaCl-KCl-MgCl2 are two of the chloride salt systems that are promising for being used as high-temperature heat transfer fluid (HTF) and thermal energy storage (TES) materials in a wide range of temperatures from 230 °C to 750 °C in concentrated solar thermal power systems. To conduct measurement of the heat transfer coefficient of the molten salt at high temperatures, a circulation system and instrumentation of flow and heat transfer was constructed. Experimental measurement of the convective heat transfer coefficients of NaCl-KCl-ZnCl2 (molar fraction: 13.8–41.9–44.3%) inside tubes has been accomplished to find the most suitable heat transfer correlations. Experience of salt processing and operation of the high-temperature heat transfer test system was obtained. Two correlations, Dittus-Boelter equation and Gnielinski’s correlation for Nusselt number against Reynolds number and Prandtl number, are evaluated using the test results, and the latter correlation is recommended due to its better agreement of prediction against tested data.

Energy & Fuels↗

DOE OSTI2022

Development of High-Temperature Emissivity Measurement Capabilities for Molten Salts at PNNL

In this study, an emissivity measurement system for a liquid molten salt was developed on the bases on the Stefan Boltzmann Law. A prototype device operating in ambient atmosphere was constructed an initial result compared well with available literature. The diffuse emissivity of NaCl-KCl system (NaCl, 51mol% NaCl – 49mol% KCl and KCl) was measured from 550 to 850 °C at a wavelength of 1.3 µm. The system appears to be relatively invariant with composition but a clear trend of decreasing emissivity values from ~0.9 at 550 °C to 0.75 at 850 °C was observed. A schematic for an enclosed system for inert atmosphere and actinide salts was drafted. Several of the components for fabrication of this device, improved laser system, furnace, nickel for capsule construction, have been purchased and are ready for assembly. The new laser system will have an improved measurement range of 275-1000 °C. The clam shell furnace has a maximum temperature of 1200 °C and will support the hermetically sealed inert encapsulation vessels. Nickel plate and tubing will create a relatively corrosion resistance capsule for testing that can withstand temperature up to 1000 °C. Emissivity measurements are important for a larger effort to understand radiative heat transfer within molten salts at elevated temperatures (600-1000 °C). Literature review of optical salt properties and radiative heat transfer models indicated that systems within elevated temperature regimes could see upwards of 20% or more of their total heat transferred through photonic mechanisms. Ultimately, future work will measure the total thermal conductivity and break down the molecular and radiative portions. Thermal conductivity, along with other thermal properties of molten salts, both coolant and fuel, are fundamental to modeling and simulations that support MSR design. The results presented here and ongoing work at PNNL will be useful in selecting optimal salt compositions, designing reactor systems, and optimizing heat transfer within a MSR power plant.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2023

FY23 Progress Report on Viscosity and Thermal Conductivity Measurements of Molten Salts

As presented in this report, thermal conductivity and viscosity measurements were performed on key chloride pseudo-binary molten salt systems of relevance to molten salt reactor developers. Thermal conductivity measurements were conducted with a variable gap technique, in which a known heat flux is driven across a molten salt specimen and the temperature difference is measured, allowing calculation of the thermal conductivity. This is achieved by establishing a small gap between the bottom of a cylindrical inner containment, which houses electrical heating elements, and an outer containment, which houses cooling channels; the gap size can be varied by compression of a formed bellows. A new calibration scheme was developed herein, involving a correction factor to the heat flux based on He measurements at various temperatures. Furthermore, the data processing methodology was improved to minimize the impact of radiative heat transfer in the calculation of salt specimen thermal conductivity from the temperature difference measurements. Viscosity measurements were conducted with a rolling ball viscometer, in which a ball rolls some known distance in an angled tubular crucible, and the terminal velocity can be used to calculate the viscosity of the salt. The measurement can be performed in a quartz crucible, with which a standard camera can be used to track the ball, or in a metal crucible, with which x-ray radiography is required to track the ball. A new custom x-ray system was made and dedicated to the rolling ball viscometer to enable high throughput automated measurements with salts which require containment with metal. Both systems have been integrated with a ventilation stack which allows for off-gassing of radioactive material, enabling future measurements with U-bearing salts. The thermal conductivity measurements performed herein were with NaCl-KCl (44 mol% NaCl). This salt system was measured in the previous fiscal year, however the thermal conductivity values obtained were comparatively low, and so the system was remeasured with the aforementioned calibration scheme and improved post-processing techniques. The newly obtained thermal conductivity values for NaCl-KCl (44 mol% NaCl) indicate good agreement with kinetic theory and ab-initio models (within 5–10 %). The viscosity measurements performed herein were with three different compositions of NaCl-KCl: 75, 50, and 25 mol% NaCl; a new calibration scheme was applied to account for variable flow effects in the laminar regime. The results show reasonable agreement with literature (5–20 %, depending on the temperature, composition, and study); however, literature values are likely higher than true values based on pure end-member measurements performed in the comparative studies. The measurements conducted herein do show a trend such that viscosity increases with increasing NaCl concentration, which agrees well with one of two comparative studies. In general, the measurements conducted herein gives confidence in the capability to use these systems to accurately measure thermal conductivity and viscosity of actinide-bearing salts within the next fiscal year.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2022

Major Ion Toxicity to Glochidia of Common and Imperiled Freshwater Mussel Species

Freshwater mussel taxa are severely imperiled and among the most sensitive to several contaminants, including chloride. Relatively little is known of the toxicity of major ions to glochidia (larvae), particularly for rare species, or the effects of hardness on major ion toxicity to glochidia. Therefore, the primary objectives of this work were to: (1) determine the acute toxicity of major ion salts to glochidia, (2) compare chloride sensitivity of glochidia from common and rare species, and (3) evaluate the relationship between water hardness and chloride toxicity to glochidia. We assessed 24 h EC50s for fatmucket (Lampsilis siliquoidea) glochidia exposed to NaCl, KCl, MgCl 2 , CaCl 2 , Na 2 SO4, MgSO 4 , CaSO 4 , and NaHCO 3 in moderately hard water. We determined NaCl EC50s for four species and KCl EC50s for glochidia of three species. Toxicity of chloride was generally consistent among the various chloride salts except for KCl, which was more toxic than all others by 1–2 orders of magnitude. Our results suggest that commonly tested species may be generally representative of rare species. Water hardness ameliorated the toxicity of chloride for all species to varying degrees. Results of this work indicate that some existing water quality criteria that do not include mussel toxicity data may not be protective of freshwater mussels.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2025

Upcycling Polyethylene Waste into Hybrid Graphitic Porous Carbon Materials Used in High‐Performance Zinc‐Ion Hybrid Capacitors

Polyethylene (PE) waste is a challenge to upcycle into useful materials because this plastic tends to decompose into volatile compounds when heated at relatively low temperatures. In this work, mixtures of PE wastes into a hybrid graphitic porous carbon (HGPC) by a thermal oxidation pretreatment step, with assistance of an inert solid additive (KCl), to functionalize, crosslink, and stabilize the PE waste followed by carbonization and catalytic graphitization steps with a potassium carbonate catalyst, are upcycled. The PE waste‐derived HGPC (PW‐HGPC) has a hybrid structure composed of graphene‐like carbon nanosheets grown on the surface of carbon particles, high porosity with specific surface area, up to 1,763 m 2 g −1 , and good graphitic degree with average Raman I 2D / I G ratios of 0.53. When used as cathode material for zinc‐ion hybrid capacitors, this PW‐HGPC exhibits an excellent specific capacity, up to 126.7 mAh g −1 , at high mass loading of 10 mg cm −2 . Moreover, PW‐HGPC exhibits remarkable cycling stability with capacity retention of >94% after 10 000 cycles. Additionally, the KCl is recycled and reused over five times. This method provides a new solution for upcycling PE wastes into high value‐added carbon materials, not only for zinc‐ion hybrid capacitors but also for other electrochemical energy storage device applications.

hybrid graphitic porous carbon↗

DOE OSTI2021

Penetration of Fission Products Ions into Complex Solids and the Effect of Ionic Wash Methods

During washing of radiologically impacted building surfaces, penetration of radionuclide ions into complex solids associated with these surfaces may occur. This study investigates the penetration of Cs-137, Sr-85, and Eu-152 solutions into numerous common building materials and radionuclide behavior when these materials were exposed to a static bath or low-pressure flow of tap water, 0.1 M potassium chloride (KCl), and 0.5 M KCl. The decontamination efficacy and the depth profile for residual contamination were measured to determine the conditions under which applying a wash solution has benefit compared to physically removing the surface material. On asphalt, 70-80% of the radionuclides were found to be within 0.02 mm of the surface. Concrete is more porous than asphalt, and 80% of the radionuclides were within 0.2 mm of the surface for Cs-137 and Eu-152 and 50-80% for Sr-85. Water effectively removed all contaminants from hard nonporous surfaces. Finally, this paper illustrates that a wash penalty factor concept-defined as ratio of the depth at which 50% of the radioactivity is found in the washed sample divided by the depth at which 50% of radioactivity is found in the control-can serve as a way to quantify whether the wash method increases the depth at which contamination penetrates into the material and thus the material becomes more difficult to decontaminate.

building materials↗

DOE OSTI2024

Technical and economic evaluation of heat transfer fluids for a TES system integrated to an advanced nuclear reactor

The utilization of thermal energy storage technology has emerged as a potential enhancement for nuclear power plants. Although nuclear energy systems possess the ability to adjust their energy output, prolonged variations in production can impact the plant's overall efficiency and economic viability. However, the nuclear industry can capitalize on thermal energy storage to bolster the power plant's economics by leveraging ancillary services and market hedging strategies. Here this research aims to advance the development of thermal energy storage for advanced nuclear reactors by assessing the thermophysical properties of various heat transfer fluids, including FLiNaK, KCl-MgCl 2 , LiCl-KCl, (LiNaK) 2 CO 3 , NaF-ZrF 4 , and KF-ZrF 4 , at temperatures ranging from 500 to 900oC. The assessment is conducted based on thermophysical correlations established in previous studies and employs figures of merit as a metric to evaluate the heat transfer performance of different salt candidates. Additionally, a cost analysis is conducted to provide an idea of the potential cost associated with each salt candidate.

25 ENERGY STORAGE↗

DOE OSTI2026

Processing iridium foil targets for the production of radioplatinum isotopes

Dissolving noble metals remains challenging because of their high reduction potentials and tendency to passivate as oxides. This barrier is acute for iridium metal targets used to produce platinum radioisotopes, where post-irradiation processing is costly and hazardous with conventional routes. Here, we report a rapid alkali-fusion method that converts Ir metal directly into chloride media compatible with downstream separations. In the process, an Ir foil is fused with Na 2 O 2 and KCl at temperatures above the KCl melting point; the molten salt enhances heat transfer and facilitates O 2− /Na + transport to the Ir surface, overcoming Ir's oxidation resistance. The fused cake is then cooled and leached in 10 M HCl, yielding Ir in solution without specialized microwave digestion or HF. Pt separation from bulk Ir was evaluated using extraction-chromatography resins. A newly formulated ionic-liquid resin containing Cyphos IL 104 (E104) was compared with two commercial resins (TrisKem TK200 and TK201). All resins achieved >90 % Ir recovery. Pt co-recovery depended on resin chemistry: TK200 recovered 85.9 % Pt, TK201 recovered 54.1 % Pt, and E104 recovered 72.9 % Pt. This study introduces a fast, scalable dissolution route for solid Ir targets and demonstrates resin choices that tune Ir/Pt separation, lowering the barrier to routine production and purification of Pt radioisotopes.

07 ISOTOPE AND RADIATION SOURCES↗

DOE OSTI2024

Upcycling linear low-density polyethylene waste to turbostratic graphene for high mass loading supercapacitors

Linear low-density polyethylene (LLDPE) waste is difficult to upcycle into more valuable carbon materials because it tends to completely decompose into small molecules during thermal processing. In this work, LLDPE is upcycled into a high quality turbostratic graphene using a pre-treatment step to oxidatively crosslink the polymer with the assistance of solid additives (KCl and K 2 CO 3 ) that improve crosslinking by increasing the effective surface area of the polymer melt during processing. After this pretreatment step, the crosslinked polymer could then be carbonized and catalytically graphenized between 400–950°C without decomposition of the polymer feedstock. The LLDPE derived graphene (LLDPE-G) obtained from this process has a Brunauer–Emmett–Teller (BET) specific surface area, up to 1800m 2 g -1 and average Raman I D /I G and I 2D /I G ratios of 0.85 and 0.57, respectively, indicating high quality graphene. When used as an electrode material in symmetric supercapacitors, LLDPE-G possesses a specific capacitance up to 175Fg -1 at a mass loading of 20mgcm -2 , which is two times the commercial requirement, yielding an areal capacitance of 3.5 Fcm -2 . Moreover, LLDPE-G exhibits exceptional cycling stability with a capacitance retention of 95.8 % after 100,000 cycles at a current density of 4.0 Ag -1 . Additionally, the KCl and K 2 CO 3 solids are recycled and reused over 3 complete reaction cycles to make new LLDPE-G with the material quality and electrocapacitive performance retained and verified after each cycle. Our approach creates new opportunities for upcycling waste LLDPE and other varieties of polyethylene into a higher value graphene used for electrochemical energy storage applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Visualizing time-dependent microstructural and chemical evolution during molten salt corrosion of Ni-20Cr model alloy using correlative quasi in situ TEM and in situ synchrotron X-ray nano-tomography

In situ monitoring of corrosion processes is important to fundamentally understand the kinetics and evolution of materials in harsh environments. A quasi in situ transmission electron microscopy technique was utilized to study microstructural and chemical evolution of a Ni-20Cr disc sample 6 exposed to molten KCl-MgCl 2 salt for 60 s in consecutive 20 s iterations. In situ synchrotron X-ray nano-tomography was performed to characterize the morphological evolution of a Ni-20Cr microwire exposed to molten KCl-MgCl 2 . Here, both techniques captured key corrosion events and revealed mechanisms at different time and length scales, potentially bringing greater insights and 10 deeper understanding beyond conventional analysis.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Computational and experimental study of different brines in temperature swing solvent extraction desalination with amine solvents

Rapid global urbanization and high-salinity wastewater disposal from industrial activities have exerted significant pressure on water resources. Over the past few years, temperature swing solvent extraction (TSSE) has been identified as a promising technique to desalinate hypersaline brines. Despite its potential, the TSSE desalination literature has been mainly based on empirical insights, and the limited molecular simulation studies have primarily focused on NaCl brines. Herein, we use molecular dynamics (MD) simulations to study the TSSE desalination of four different brines, namely, KCl, KBr, NaCl, and NaBr using diisopropylamine as the solvent. Based on both bulk and interfacial brine-diisopropylamine MD results, here we investigate the qualitative and quantitative performance of the simulations by benchmarking these results against our experimental evaluations of these same systems. MD results provide satisfactory qualitative agreement with the experimental data of water solubilization in the organic phase and amine solubilization in the aqueous phase for the KBr, KCl, and NaBr brines. Also, the molecular mechanism of solvation of ionic species by water molecules over diisopropylamine suggested by the MD simulations is in agreement with our experimental data. However, larger qualitative and quantitative deviations were observed for the NaCl brines, and this is likely due to polarization and charge transfer effects, as quantified by our quantum chemical calculations.

42 ENGINEERING↗

DOE OSTI2026

Nano zero valent iron electrodeposition at boron doped diamond electrodes

Here, in this study, we present an ecofriendly and simple electrochemical method for synthesizing nano zero-valent iron particles (nZVIs) directly on boron-doped diamond (BDD) electrode surfaces. A BDD electrode served as the substrate for electrodeposition using a 5 mM FeCl 3 /0.1 M KCl solution and chronoamperometry at an applied potential of −1.3 V versus Ag/AgCl (1 M KCl), as determined by cyclic voltammetry (CV) and supported by Pourbaix diagram analysis. The electrochemical behavior and surface modification were characterized using CV, electrochemical impedance spectroscopy (EIS), and surface analysis and microscopy techniques. The results confirm that BDD electrodes can serve as effective platforms for a controlled deposition of 56 nm nZVIs, offering a promising strategy for the development of advanced materials for environmental remediation, catalysis, and sensing applications.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Computing the solubility of argon and xenon in molten sodium chloride and potassium chloride salts

Molten salt reactors (MSRs) offer significant advancements in nuclear reactor safety and efficiency by operating at higher temperatures and lower pressures compared to traditional reactors. A critical aspect of MSR operation involves understanding the solubility of fission byproducts, particularly noble gases, in the molten salts used. This study employs molecular dynamics (MD) simulations to compute Henry’s law constants and enthalpies of solvation for argon and xenon in molten sodium chloride (NaCl) and potassium chloride (KCl). We developed a new pairwise potential for the noble gas and salt interactions based on first principles calculations. We then used this potential to calculate Henry’s law constants of the two gases in the molten salts, which were modeled using both a rigid ion model (RIM) and a polarizable ion model (PIM). The solubility calculations, performed using the Widom insertion method, show qualitative agreement with limited experimental data, highlighting the temperature dependence and greater solubility of both gases in KCl compared to NaCl. Additionally, free volume analysis elucidated the role of available space within the molten salts in governing solubility trends. Our findings suggest that PIM trajectories provide more reliable predictions for noble gas solubility than RIM due to their accurate density representation. Furthermore, these results enhance understanding of gas solubility in MSR environments, and the methods can be readily extended to other systems.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2025

Mn(II)-induced phase transformation of Mn(IV) oxide in seawater

Manganese (Mn) oxides are key components of oceanic and lacustrine Mn nodules and influence metal cycling through oxidation and adsorption processes. Layered Mn oxides (LMOs) are the most common minerals in these nodules and the immediate products of microbially mediated Mn(II) oxidation by O 2 . LMOs can transform into tunneled Mn oxides (TMOs), Mn oxyhydroxides (MnOOH), or Mn(II,III) phase (Mn 3 O 4 ). LMOs often concur with Mn(II) in the environment and the adsorption and oxidation of Mn(II) by LMOs can greatly promote the transformation of LMOs to those phases. However, the Mn(II)-promoted transformation of LMOs in seawater—rich in various cations (300 mM Na + , 10 mM K + , 50 mM Ca 2+ , and 10 mM Mg 2+ ) remains poorly understood. We examined the transformation of δ-MnO 2 in artificial seawater (pH 8.2) under anoxic conditions with the Mn(II)/MnO 2 ratio (r) ranging from 0.08 to 3.83. To assess the effect of ionic strength (IS), parallel experiments were conducted in a mixed 530 mM NaCl and 10 mM KCl solution (having seawater ionic strength but without Ca 2+ and Mg 2+ ) and in 100 mM NaCl solution as a control. At low r (0.08), δ-MnO 2 transformed into triclinic birnessite and a 4 × 4 TMO in 100 mM NaCl solution, which, however, was suppressed in seawater due to strong interactions of Ca 2+ /Mg 2+ with δ-MnO 2 . In the mixed 530 mM NaCl and 10 mM KCl solution (the same ionic strength as of seawater), the transformation occurred extensively but the products had lower crystallinity compared to in 100 mM NaCl solution. At the high Mn(II)/MnO 2 ratios (0.5 ≤ r ≤ 3.83), δ-MnO 2 transformed extensively into MnOOH phases and hausmannite (Mn 3 O 4 ) in 100 mM NaCl solution. The seawater suppressed the transformation, but the suppression became weaker with increasing Mn(II)/MnO 2 ratio. For example, the transformation was completely suppressed at r = 0.5 but essentially negligible at r = 3.83. The suppression at these high Mn(II)/MnO 2 ratios was mainly ascribed to the influence of Ca 2+ and Mg 2+ rather than of the high IS, and the weaker suppression at the higher Mn(II)/MnO 2 ratio suggests stronger competition of Mn(II) with Ca 2+ /Mg 2+ for interacting with δ-MnO 2 . Moreover, the composition and crystallinity of the transformation products (i.e., the relative abundance of MnOOH (α, β, and γ) and Mn 3 O 4 ) were influenced by both the high ionic strength and the presence of Ca 2+ and Mg 2+ . Therefore, even though Ca 2+ and Mg 2+ concentrations are much lower than Na + in seawater, their impacts on the transformation are dominant. Our study explains why MnOOH phases, hausmannite, and TMOs are less common than LMOs in oceanic environments, partially because seawater chemistry suppresses their formation. LMOs are the most reactive for metal adsorption and oxidation among all Mn oxides. Thus, the high stability of LMOs in an oceanic environment confers the high impacts of Mn oxides on metal cycling in the ocean.

Divalent manganese↗

DOE OSTI2021

Multielectrode Array Sensors to Enable Long-Duration Corrosion Monitoring and Control of Concentrating Solar Power Systems

Molten mixtures of MgCl2-KCl-NaCl are promising heat transfer fluid (HTF) candidates for the next generation of concentrating solar power systems (Gen3 CSP), because of their low cost, high decomposition temperature, and favorable heat transfer characteristics. However, if the chemistry of the salts is not properly controlled, molten chlorides can cause corrosion of high-temperature metal alloys, such as Inconel (R), in CSP systems. Here we demonstrate a corrosion monitoring system that can be used to monitor the health of the structural alloys over long durations. The monitoring system includes a multielectrode array voltammetry sensor that measures the redox potential of molten MgCl2-KCl-NaCl mixture as well as the presence of corrosion products and impurities. The sensors have been successfully operated in static molten salt environments for long durations, and are capable of detecting corrosion products, such as Cr2+ and Fe2+, quantitatively at low concentrations (i.e., approximately 100 ppm) with less than 4% error.

Concentrated solar power↗