Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Jet impingement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Two-Phase Azimuthal Instability Generated By A Supersonic Jet Impinging on A Granular Bed

A persistent azimuthal pattern featuring alternate high and low concentration of ejecta emanating from the area where a supersonic jet (Mach 5.3) impinges on a bed of particles in a near-lunar vacuum condition is studied experimentally. Although this peculiar phenomenon has been documented in early studies motivated by extraterrestrial landing, the mechanism of this pattern is not clearly understood. Recently, a series of experiments were conducted at NASA Marshall Space Flight Center inside a 4.5 m vacuum chamber over a range of reduced ambient pressure. Experimental results show vibrant azimuthal patterns, which are clearest at low ambient pressure. The pattern is shown to be driven by the flow instability at low Reynolds number, despite the supersonic jet employed. The flow instability leads to azimuthal vortex lines, which expel ejecta into streaks between two neighboring vortex lines. A simple model is proposed to explain the observed phenomenon.

Plume Surface Interaction↗
NASA NTRS1976

Investigations of scaling laws for jet impingement

The statistical properties of tangential flows over surfaces were investigated by two techniques. In one, a laser-Doppler velocimeter was used in a smoke-laden jet to measure one-point statistical properties, including mean velocities, turbulent intensities, intermittencies, autocorrelations, and power spectral densities. In the other technique, free stream and surface pressure probes connected to 1/8 inch microphones were used to obtain single point rms and 1/3 octave pressures, as well as two point cross correlations, the latter being converted to auto spectra, amplitude ratios, phase lags, and coherences. The results of these studies support the vortex model of jets, give some insights into the effects of surface impingement, and confirm that jet diameter and velocity are the scaling parameters for circular jets, while Reynolds number is relatively unimportant.

Morton, J. B.↗
NASA NTRS1975

Analysis of noise produced by jet impingement near the trailing edge of a flat and a curved plate

The sound fields produced by the interaction of a subsonic cold gas jet with the trailing edge of a large flat plate and a curved plate were analyzed. The analyses were performed to obtain a better understanding of the dominant noise source and the mechanism governing the peak sound-pressure-level frequencies of the broadband spectra. An analytical expression incorporating an available theory and experimental data predicts sound field data over an arc of approximately 105 deg measured from the upstream jet axis for the two independent sets of data. The dominant noise as detected on the impingement side of either plate results from the jet impact (eighth power of the velocity dependence) rather than a trailing-edge disturbance (fifth or sixth power of the velocity dependence). Also, the frequency of the peak SPL may be governed by a phenomenon which produces periodic formation and shedding of ring vortices from the nozzle lip.

Mckinzie, D. J., Jr.↗
NASA NTRS1972

Microfog lubricant application system for advanced turbine engine components, phase 2. Tasks 3, 4 and 5: Wettability and heat transfer of microfog jets impinging on a heated rotating disc, and evaluation of reclassifying nozzles and a vortex mist generator

The wettabilities and heat transfer rates of microfog jets (oil-mist nozzle flows) impinging on a heated rotating disc were determined under an inert atmosphere of nitrogen at temperatures ranging from 600 to 800 F. The results are discussed in relation to the various factors involved in the microfog lubricant application systems. Two novel reclassifying nozzles and a vortex mist generator were also studied.

Shim, J.↗
NASA NTRS1986

Multiple jet impingement flowfields

Attention is given to the prediction of lift-system-induced aerodynamic effects in lift-jet VTOL aircraft, considering both analytical fluid-dynamics models and an empirical database. The methodology takes into account the effects of aircraft geometry and orientation as well as height above ground, lift-jet vector and splay directions, jet exit-flow conditions, and nozzle exit geometry.

Kotansky, D. R.↗
NASA NTRS1970

Flow characteristics of an air jet impinging on a flat surface

Survey develops adequate heat transfer correlations for design use. Flow characteristics studies include - potential core length, velocity and pressure distribution through the jet, and spread of jet and velocity decay along jet axis.

Gauntner, J. W.↗
NASA NTRS1980

Multiple jet impingement heat transfer characteristic: Experimental investigation of in-line and staggered arrays with crossflow

Heat transfer characteristics were obtained for configurations designed to model the impingement cooled midchord region of air cooled gas turbine airfoils. The configurations tested were inline and staggered two-dimensional arrays of circular jets with ten spanwise rows of holes. The cooling air was constrained to exit in the chordwise direction along the channel formed by the jet orifice plate and the heat transfer surface. Tests were run for chordwise jet hole spacings of five, ten, and fifteen hole diameters; spanwise spacings of four, six, and eight diameters; and channel heights of one, two, three, and six diameters. Mean jet Reynolds numbers ranged from 5000 to 50,000. The thermal boundary condition at the heat transfer test surface was isothermal. Tests were run for sets of geometrically similar configurations of different sizes. Mean and chordwise resolved Nusselt numbers were determined utilizing a specially constructed test surface which was segmented in the chordwise direction.

Florschuetz, L. W.↗
NASA NTRS1972

An analytical investigation of the impingement of jets on curved deflectors.

Numerical solutions are obtained for the cases of straight circular jets impinging on axisymmetric curved surfaces, and plane jets impinging symmetrically on two-dimensional curved surfaces. These geometries are representative of some types of thrust reversers for transport aircraft. The solutions are based on the assumptions of incompressible and potential flow. The velocity field, pressure distribution at the deflector surface, and reverser effectiveness are predicted for deflector turning angles of 15 to 75 deg, deflector width to jet diameter ratios of 1.5-2.0, and ratios of deflector clearance to jet diameter of 1.0-3.0. Reverser effectiveness is found to be a maximum for a ratio of deflector clearance to jet diameter of about 2.0. The effect of back pressuring resulting from the presence of the deflector is predicted.

Schnurr, N. M.↗
DOE OSTI2023

Engineering endosomolytic nanocarriers of diverse morphologies using confined impingement jet mixing

The clinical translation of many biomolecular therapeutics has been hindered by undesirable pharmacokinetic (PK) properties, inadequate membrane permeability, poor endosomal escape and cytosolic delivery, and/or susceptibility to degradation. Overcoming these challenges merits the development of nanoscale drug carriers (nanocarriers) to improve the delivery of therapeutic cargo. Herein, we implement a flash nanoprecipitation (FNP) approach to produce nanocarriers of diverse vesicular morphologies by using various molecular weight PEG-bl-DEAEMA-co-BMA (PEG-DB) polymers. We demonstrated that FNP can produce uniform (PDI < 0.1) particles after 5 impingements, and that by varying the copolymer hydrophilic mass fraction, FNP enables access to a diverse variety of nanoarchitectures including micelles, unilamellar vesicles (polymersomes), and multi-compartment vesicles (MCVs). We synthesized a library of 2 kDa PEG block copolymers, with DEAEMA-co-BMA second block molecular weights of 3, 6, 12, 15, 20, and 30 kDa. All formulations were both pH responsive, endosomolytic, and capable of loading and cytosolically delivering small negatively charged molecules – albeit to different degrees. Using a B16.F10 melanoma model, we showcased the therapeutic potential of a lead FNP formulated PEG-DB nanocarrier, encapsulating the cyclic dinucleotide (CDN) cGAMP to activate the stimulator of interferon genes (STING) pathway in a therapeutically relevant context. Collectively, these data demonstrate that an FNP process can be used to formulate pH-responsive nanocarriers of diverse morphologies using a PEG-DB polymer system. As FNP is an industrially scalable process, these data address the critical translational challenge of producing PEG-DB nanoparticles at scale. Furthermore, the diverse morphologies produced may specialize in the delivery of distinct biomolecular cargos for other therapeutic applications, implicating the therapeutic potential of this platform in an array of disease applications.

36 MATERIALS SCIENCE↗
NASA NTRS1974

Research on free and impinging jets for the development of STOL aircraft

The effect of the exit plane conditions on the initial region of an axisymmetric jet was systematically investigated. An essentially top-hat mean velocity profile and a homogeneous turbulence structure were maintained at the exit plane for eight distinct scale and intensity conditions. Mass and momentum flux values are independent of the exit turbulence structure for the range investigated; however, a significant (approximately 25%) increase in the latter implies a pronounced static pressure decrement inside the jet. Details of the velocity profile and turbulence structure are influenced by the exit plane conditions. The three radial-axial components of the Reynolds stress tensor have been conditionally sampled and are analyzed to show the initial condition effects.

Foss, J. F.↗
NASA NTRS1986

Full-scale ground effects of twin impinging jets beneath a subsonic tactical V/STOL aircraft

This paper presents a summary of an analysis of flow field characteristics about a large scale twin-tilt-nacelle V/STOL aircraft in close proximity to the ground. The analysis uses experimental data in the form of measurements of pressure distributions on the ground beneath the aircraft and on the undersurface of the aircraft's fuselage. The integrals of these distributions are compared with forces measured directly, for both the total model and isolated nacelles, (i.e., net thrust). The handling qualities of the vehicle were found to be influenced by flow field characteristic features, not present in simpler models. Lift increases and significant degradation in roll control occur at low heights for fuselage strake deflections of 30 degrees or more. Reductions in control effectiveness about the other axes were also observed.

Dudley, Michael R.↗
NASA NTRS1992

Combustion of LOX with H2(sub g) under subcritical, critical, and supercritical conditions (Task 1) and experimental observation of dense spray and mixing of impinging jets (Task 2)

The objective was to achieve a better understanding of the combustion processes of liquid oxygen and gaseous hydrogen under broad range of pressure covering subcritical, critical, and supercritical conditions. The scope of the experimental work falls into the following areas: (1) design of the overall experimental setup; (2) modification of an existing windowed high pressure chamber; (3) design of the LOX feeding system; (4) provision of the safety features in the test rig design; (5) LOX cleanliness requirements; (6) cold shock testing; (7) implementation of data acquisition systems; (8) preliminary tests for system checkout; (9) modification of LOX feeding system; and (10) evaporation tests. Progress in each area is discussed.

Kuo, K. K.↗