Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ION MICROSCOPE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Ion Engine Grid Gap Measurements

A simple technique for measuring the grid gap of an ion engine s ion optics during startup and steady-state operation was demonstrated with beam extraction. The grid gap at the center of the ion optics assembly was measured with a long distance microscope that was focused onto an alumina pin that protruded through the center accelerator grid aperture and was mechanically attached to the screen grid. This measurement technique was successfully applied to a 30 cm titanium ion optics assembly mounted onto an NSTAR engineering model ion engine. The grid gap and each grid s movement during startup from room temperature to both full and low power were measured. The grid gaps with and without beam extraction were found to be significantly different. The grid gaps at the ion optics center were both significantly smaller than the cold grid gap and different at the two power levels examined. To avoid issues associated with a small grid gap during thruster startup with titanium ion optics, a simple method was to operate the thruster initially without beam extraction to heat the ion optics. Another possible method is to apply high voltage to the grids prior to igniting the discharge because power deposition to the grids from the plasma is lower with beam extraction than without. Further testing would be required to confirm this approach.

Soulas, Gerge C.↗
DOE OSTI2025

Turn-On Conductivity with Proton-Coupled Electron Transport in Metal–Organic Frameworks

Proton-coupled electron transfer (PCET) has been studied for decades in the context of molecular reactivity, but its impact on long-range electron transport is barely understood. When defined broadly as ion-coupled charge transport (ICCT), relevant systems include lithium-ion battery electrodes, electrochromic coatings, and myriad electrocatalysts. Despite ample evidence that ion-electron coupling enhances or diminishes the performance of these devices, little is known about the experimental signatures of ICCT and the microscopic factors that govern its mechanism. Here, we expect that ion-electron coupling becomes especially relevant in high surface area materials, such as the layered electrodes of intercalation batteries, due to the close proximity of itinerant electrons and electrolyte. Here, we report an electrochemical investigation into a family of metal-organic frameworks (MOFs) that serves as a well-defined platform for understanding the effect of ICCT on both elec- tronic and ionic conductivity. Through photochemical doping of e - –H + pairs and introduction of solvent guest molecules, the Ti-containing MOFs convert from electronic-only insulators conductors (σ e ≈ 10 -12 S cm -1 ) to mixed ion-electron semiconduc- tors (σ e ≈ 10 -7 S cm -1 , σ ion ≈ 10 -5 S cm -1 ). Direct current and alternating current techniques support the existence of proton- electron coupling and, critically, that improved ionic conductivity enhances electronic conductivity. Taken together, these results provide direct evidence that PCET enables long-range charge transport and generalized electrochemical tools and synthetic methods for studying ion-electron coupling in materials broadly.

Charge transport↗
DOE OSTI2024

Insights into the structure and dynamics of K + ions at the muscovite–water interface from machine learning potential simulations

The surfaces of many minerals are covered by naturally occurring cations that become partially hydrated and can be replaced by hydronium or other cations when the surface is exposed to water or an aqueous solution. These ion exchange processes are relevant to various chemical and transport phenomena, yet elucidating their microscopic details is challenging for both experiments and simulations. Here, in this work, we make a first step in this direction by investigating the behavior of the native K + ions at the interface between neat water and the muscovite mica (001) surface with ab-initio -based machine learning molecular dynamics and enhanced sampling simulations. Our results show that the desorption of the surface K + ions in pure ion-free water has a significant free energy barrier irrespective of their local surface arrangement. In contrast, facile K + diffusion between mica’s ditrigonal cavities characterized by different Al/Si orderings is observed. This behavior suggests that the K + ions may favor a dynamic disordered surface arrangement rather than complete desorption when exposed to deionized water.

Ab-initio molecular dynamics↗
DOE OSTI2026

Prediction and Experimental Verification of Electrolyte Solvation Structure from an OMol25-Trained Interatomic Potential

A molecular-level understanding of electrolyte solvation structure and ion–ion correlations is critical to developing next-generation battery chemistries. Atomistic simulation capabilities with sufficient accuracy, speed, and transferability to deliver reliable structural insights while avoiding arduous system-specific reparameterization are thus highly desirable. Machine learning interatomic potentials (MLIPs) trained on large, chemically diverse data sets are revolutionizing computational chemistry, enabling molecular dynamics simulations of battery electrolytes with near-DFT accuracy over 10,000× faster than DFT. While previous MLIP training data sets with suitable elemental coverage for electrolytes have been based on inorganic materials, the Open Molecules 2025 (OMol25) data set provides large-scale molecular DFT MLIP training data with broad elemental coverage and specifically samples tens of millions of electrolyte configurations. Here, we integrate computational modeling with experimental validation to systematically assess the ability of large-scale MLIPs pretrained on materials data or on OMol25 to accurately resolve nanoscale structural organization and ion-solvation characteristics in Na-ion battery electrolytes across diverse physicochemical conditions and compositional regimes. We find that the OMol25-trained Universal Model of Atoms (UMA-OMol) predicts experimentally measured densities and X-ray structure factors in substantially better agreement compared to state-of-the-art models trained only on inorganic materials data. Using UMA-OMol, we further analyze systematic trends in solvation structure as a function of cation identity, anion chemistry, salt concentration, and solvent topology. We observe that increasing system temperature amplifies the heterogeneity within the solvation environment, perturbing cation–solvent interactions and promoting the formation of contact ion pairs (CIPs). Moreover, subtle variations in the solvent topology of glyme-based electrolytes cause pronounced changes in ion correlations and solvation structure. The experimental agreement and microscopic insights shown here position OMol25-trained MLIPs as a practical route to predictive, high-throughput electrolyte simulations beyond the limits of classical force fields and direct DFT molecular dynamics, serving as a powerful tool for accelerating the design of next-generation Na-ion battery electrolytes and beyond.

MLIPs↗
NASA NTRS1976

Ion beam sputter modification of the surface morphology of biological implants

The surface chemistry and texture of materials used for biological implants may significantly influence their performance and biocompatibility. Recent interest in the microscopic control of implant surface texture has led to the evaluation of ion beam sputtering as a potentially useful surface roughening technique. Ion sources, similar to electron bombardment ion thrusters designed for propulsive applications, are used to roughen the surfaces of various biocompatible alloys or polymer materials. These materials are typically used for dental implants, orthopedic prostheses, vascular prostheses, and artificial heart components. Masking techniques and resulting surface textures are described along with progress concerning evaluation of the biological response to the ion beam sputtered surfaces.

Weigand, A. J.↗
NASA NTRS1971

Measurement of lattice damage caused by ion-implantation doping of semiconductors.

Discussion of two new techniques used to measure the lattice damage produced in GaAs by the implantation of 60 keV cadmium ions. In the first method, optical reflection spectra of the ion-implanted samples were measured in the wavelength range from 2000 to 4600 A. The decrease in reflectivity resulting from ion-implantation was used to determine the relative amount of lattice damage as a function of ion dose. The second technique employed the scanning electron microscope. Patterns very similar in appearance to Kikuchi electron diffraction patterns are obtained when the secondary and/or backscattered electron intensity is displayed as a function of the angle of incidence of the electron beam on a single crystal surface. The results of measurements made by both methods are compared with each other and with data obtained by the method of measuring lattice damage by Rutherford scattering of 1 MeV helium ions.

Hunsperger, R. G.↗
NASA NTRS1984

Method of making an ion beam sputter-etched ventricular catheter for hydrocephalus shunt

The centricular catheter comprises a multiplicity of inlet microtubules. Each microtubule has both a large opening at its inlet end and a multiplicity of microscopic openings along its lateral surfaces. The microtubules are perforated by an ion beam sputter etch technique. The holes are etched in each microtubule by directing an ion beam through an electro formed mesh mask producing perforations having diameters ranging from about 14 microns to about 150 microns. This structure assures a reliable means for shunting cerebrospinal fluid from the cerebral ventricles to selected areas of the body.

Banks, B. A.↗
DOE OSTI2026

Irradiation-Induced Grain Growth of gamma-Fe2O3 and Fe3O4 at Cryogenic Temperatures

This work reports the first observations of grain growth under irradiation of Fe oxides, specifically maghemite gamma-Fe2O3 and magnetite Fe3O4. The Fe oxide thin films were grown by Pulsed Laser Deposition and irradiated in-situ in a Transmission Electron Microscope at - 223°C using 1 MeV Kr2+ ions up to 8.75 x 10^19 ions/m^2 to study grain growth kinetics under irradiation. Grain growth at such low temperatures appears to follow kinetics that can be accounted for by the thermal spike model developed for metals in the literature. The corresponding activation energies were calculated and compared with other oxides. The results demonstrate that gamma-Fe2O3, despite its larger initial grain size, exhibits surprisingly fast grain growth in comparison with Fe3O4, likely due to the presence of iron vacancies in the crystal structure that facilitate faster atomic diffusion under irradiation.

Kretov, Dmitrii↗
NASA NTRS1979

Ion-beam texturing of materials

Xenon ion-beam source is used to create microscopically-rough surface texture by sputter-etching surface while simultaneously sputter depositing lower yield material onto surface.

Hudson, W. R.↗
NASA NTRS1982

The survival of solar flare tracks in interplanetary dust silicates on deceleration in the earth's atmosphere

Pulse heating experiments on magnesium-rich olivine and pyroxene, two silicates often found in micrometeorites collected in the stratosphere, show that iron ion tracks remain detectable in the transmission electron microscope for temperature maxima up to approximately 600 C. Assuming thermal emissivities near unity, this implies that micrometeorites with surface densities above 1 mg/sq cm are likely to have their track record erased, and that tracks in reentrant or low-density micrometeorites smaller than 7 microns in size are likely to survive atmospheric entry.

Fraundorf, P.↗
NASA NTRS1977

Ion-beam-sputter modification of the surface morphology of biological implants

The surface chemistry and texture of materials used for biological implants may significantly influence their performance and biocompatibility. Recent interest in the microscopic control of implant surface texture has led to the evaluation of ion-beam sputtering as a potentially useful surface roughening technique. Ion sources, similar to electron-bombardment ion thrusters designed for propulsive applications, are used to roughen the surfaces of various biocompatible alloys or polymer materials. These materials are typically used for dental implants, orthopedic prostheses, vascular prostheses, and artificial heart components. Masking techniques and resulting surface textures are described along with progress concerning evaluation of the biological response to the ion-beam-sputtered surfaces.

Weigand, A. J.↗
NASA NTRS2008

Estimates of Sputter Yields of Solar-Wind Heavy Ions of Lunar Regolith Materials

At energies of approximately 1 keV/amu, solar-wind protons and heavy ions interact with the lunar surface materials via a number of microscopic interactions that include sputtering. Solar-wind induced sputtering is a main mechanism by which the composition of the topmost layers of the lunar surface can change, dynamically and preferentially. This work concentrates on sputtering induced by solar-wind heavy ions. Sputtering associated with slow (speeds the electrons speed in its first Bohr orbit) and highly charged ions are known to include both kinetic and potential sputtering. Potential sputtering enjoys some unique characteristics that makes it of special interest to lunar science and exploration. Unlike the yield from kinetic sputtering where simulation and approximation schemes exist, the yield from potential sputtering is not as easy to estimate. This work will present a preliminary numerical scheme designed to estimate potential sputtering yields from reactions relevant to this aspect of solar-wind lunar-surface coupling.

Barghouty, Abdulmasser F.↗
NASA NTRS2003

Transmission measurement based on STM observation to detect the penetration depth of low-energy heavy ions in botanic samples

The penetration depth of low-energy heavy ions in botanic samples was detected with a new transmission measurement. In the measurement, highly oriented pyrolytic graphite (HOPG) pieces were placed behind the botanic samples with certain thickness. During the irradiation of heavy ions with energy of tens of keV, the energetic particles transmitted from those samples were received by the HOPG pieces. After irradiation, scanning tunneling microscope (STM) was applied to observe protrusion-like damage induced by these transmitted ions on the surface of the HOPG. The statistical average number density of protrusions and the minimum transmission rate of the low-energy heavy ions can be obtained. The detection efficiency of the new method for low-energy heavy ions was about 0.1-1 and the background in the measurement can be reduced to as low as 1.0 x 10(8) protrusions/cm2. With this method, the penetration depth of the energetic particles was detected to be no less than 60 micrometers in kidney bean slices when the slices were irradiated by 100 keVAr+ ion at the fluence of 5 x 10(16) ions/cm2. c2002 Elsevier Science Ltd. All rights reserved.

DNA Damage↗
NASA NTRS2008

Nanotip Carpets as Antireflection Surfaces

Carpet-like random arrays of metal-coated silicon nanotips have been shown to be effective as antireflection surfaces. Now undergoing development for incorporation into Sun sensors that would provide guidance for robotic exploratory vehicles on Mars, nanotip carpets of this type could also have many uses on Earth as antireflection surfaces in instruments that handle or detect ultraviolet, visible, or infrared light. In the original Sun-sensor application, what is required is an array of 50-micron-diameter apertures on what is otherwise an opaque, minimally reflective surface, as needed to implement a miniature multiple-pinhole camera. The process for fabrication of an antireflection nanotip carpet for this application (see Figure 1) includes, and goes somewhat beyond, the process described in A New Process for Fabricating Random Silicon Nanotips (NPO-40123), NASA Tech Briefs, Vol. 28, No. 1 (November 2004), page 62. In the first step, which is not part of the previously reported process, photolithography is performed to deposit etch masks to define the 50-micron apertures on a silicon substrate. In the second step, which is part of the previously reported process, the non-masked silicon area between the apertures is subjected to reactive ion etching (RIE) under a special combination of conditions that results in the growth of fluorine-based compounds in randomly distributed formations, known in the art as "polymer RIE grass," that have dimensions of the order of microns. The polymer RIE grass formations serve as microscopic etch masks during the next step, in which deep reactive ion etching (DRIE) is performed. What remains after DRIE is the carpet of nano - tips, which are high-aspect-ratio peaks, the tips of which have radii of the order of nanometers. Next, the nanotip array is evaporatively coated with Cr/Au to enhance the absorption of light (more specifically, infrared light in the Sun-sensor application). The photoresist etch masks protecting the apertures are then removed by dipping the substrate into acetone. Finally, for the Sun-sensor application, the back surface of the substrate is coated with a 57-nm-thick layer of Cr for attenuation of sunlight.

Bae, Youngsam↗
NASA NTRS1992

A second-order theory for transverse ion heating and momentum coupling due to electrostatic ion cyclotron waves

A second-order theory for electrostatic instabilities driven by counterstreaming ion beams is developed which describes momentum coupling and heating of the plasma via wave-particle interactions. Exchange rates between the waves and particles are derived, which are suitable for the fluid equations simulating microscopic effects on macroscopic scales. Using a fully kinetic simulation, the electrostatic ion cyclotron instability due to counterstreaming H(+) beams has been simulated. A power spectrum from the kinetic simulation is used to evaluate second-order exchange rates. The calculated heating and momentum loss from second-order theory is compared to the numerical simulation.

Miller, Ronald H.↗
NASA NTRS1992

Dosimetric mapping inside biorack (7-IML-1)

This experiment documents the radiation environment inside Biorack and compares it to theoretical predictions. Other experiments inside Biorack need this information to determine whether changes to samples are caused by radiation or microgravity. Dosimetric stacks, each with 20 to 100 sheets of plastic detector foils (cellulose nitrate, Lexan, and CR39) and nuclear emulsions of different radiation sensitivity are packed together with Thermoluminescence dosimeters (TLD) inside Type 1 containers. Crew members place two stacks in the 37 C incubator and four in the 36 C incubator, two of which are placed on the 1 g centrifuge. Two stacks are located in a stowage position at ambient temperature. After the mission, the plastic detectors are etched and the nuclear emulsions are developed similar to photographic emulsions. The traces resulting from the interaction of heavy ions with matter can then be evaluated under the microscope. The number, charge, and energy of the particles will be determined. From the TLD readings, the absorbed dose of the low LET components will be received.

Reitz, G.↗
NASA NTRS1996

A Fluorescence Recovery After Photobleaching (FRAP) Technique for the Measurement of Solute Transport Across Surfactant-Laden Interfaces

The technique of Fluorescence Recovery After Photobleaching (FRAP) has been applied to the measurement of interfacial transport in two-phase systems. FRAP exploits the loss of fluorescence exhibited by certain fluorophores when over-stimulated (photobleached), so that a two-phase system, originally at equilibrium, can be perturbed without disturbing the interface by strong light from an argon-ion laser and its recovery monitored by a microscope-mounted CCD camera as it relaxes to a new equilibrium. During this relaxation, the concentration profiles of the probe solute are measured on both sides of the interface as a function of time, yielding information about the transport characteristics of the system. To minimize the size of the meniscus between the two phases, a photolithography technique is used to selectively treat the glass walls of the cell in which the phases are contained. This allows concentration measurements to be made very close to the interface and increases the sensitivity of the FRAP technique.

Browne, Edward P.↗
NASA NTRS1995

Microgravity and Charge Transfer in the Neuronal Membrane: Implications for Computational Neurobiology

Evidence from natural and artificial membranes indicates that the neural membrane is a liquid crystal. A liquid-to-gel phase transition caused by the application of superposed electromagnetic fields to the outer membrane surface releases spin-correlated electron pairs which propagate through a charge transfer complex. The propagation generates Rydberg atoms in the lipid bilayer lattice. In the present model, charge density configurations in promoted orbitals interact as cellular automata and perform computations in Hilbert space. Due to the small binding energies of promoted orbitals, their automata are highly sensitive to microgravitational perturbations. It is proposed that spacetime is classical on the Rydberg scale, but formed of contiguous moving segments, each of which displays topological equivalence. This stochasticity is reflected in randomized Riemannian tensor values. Spacetime segments interact with charge automata as components of a computational process. At the termination of the algorithm, an orbital of high probability density is embedded in a more stabilized microscopic spacetime. This state permits the opening of an ion channel and the conversion of a quantum algorithm into a macroscopic frequency code.

Wallace, Ron↗