Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HOLE DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Use of optimum stiffness tailoring to improve the compressive strength of composite plates with holes

A structural optimization procedure is used to tailor the cross-sectional stiffness distribution of compression-loaded composite plates with holes. Minimum mass designs are obtained for plates with cross sections consisting of two different balanced symmetric laminates with 0 deg, + or - 45 deg and 90 deg plies. The plate interior region contains the hole and is designed from a softer material system with a higher failure strain than the plate exterior region. All-graphite-epoxy plates and hybrid graphite/glass-epoxy plates were studied. Other designs with different percentages of 0 deg and + or 45 deg plies in the exterior laminate are compared with the optimum designs. Designs with uniform cross-sectional stiffnesses also are compared with the tailored cross-sectional stiffness designs. Specimens of each design were tested to verify the analytical predictions. The results show that cross-sectional stiffness tailoring can increase the compressive strength and decrease the mass of compression-loaded laminated plates with holes.

Haftka, R. T.↗

Bolted Double-Lap Composite Joints Under Mechanical and Thermal Loading

This study concerns the determination of the contact stresses and contact region around bolt holes and the bolt load distribution in single- and double-lap joints of composite laminates with arbitrarily located bolts under general mechanical loading conditions and uniform temperature change. The unknown contact stress distribution and contact region between the bolt and laminates and the interaction among the bolts require the bolt load distribution, as well as the contact stresses, to be as part of the solution. The present method is based on the complex potential theory and the variational formulation in order to account for bolt stiffness, bolt-hole clearance, and finite geometry of the composite laminates.

Kradinov, V.↗

Stress-intensity factors for cracks emanating from the loaded fastener hole

Using a series approach and the Muskhelishvili formulation in the two-dimensional theory of elasticity, stress-intensity factors K are derived for problems in which cracks emanate radially from the boundary of an arbitrarily loaded internal circular hole in an infinite plate. Numerical values are obtained for K(I) and K(II) for radial cracks from a hole containing a loose-fitted pin or rivet that is pulled perpendicular to the crack direction in the plane of the plate. The method is a general one for determining K for a set of symmetrically emanating radial cracks for a variety of concentrated or distributed tractions on the circular hole.

Shivakumar, V.↗

Iron charge states observed in the solar wind

Solar wind measurements from the ULECA sensor of the Max-Planck-Institut/University of Maryland experiment on ISEE-3 are reported. The low energy section of approx the ULECA sensor selects particles by their energy per charge (over the range 3.6 keV/Q to 30 keV/Q) and simultaneously measures their total energy with two low-noise solid state detectors. Solar wind Fe charge state measurements from three time periods of high speed solar wind occurring during a post-shock flow and a coronal hole-associated high speed stream are presented. Analysis of the post-shock flow solar wind indicates the charge state distributions for Fe were peaked at approx +16, indicative of an unusually high coronal temperature (3,000,000 K). In contrast, the Fe charge state distribution observed in a coronal hole-associated high speed stream peaks at approx -9, indicating a much lower coronal temperature (1,400,000 K). This constitutes the first reported measurements of iron charge states in a coronal hole-associated high speed stream.

Ipavich, F. M.↗

Heat Transfer on a Film-Cooled Rotating Blade

A multi-block, three-dimensional Navier-Stokes code has been used to compute heat transfer coefficient on the blade, hub and shroud for a rotating high-pressure turbine blade with 172 film-cooling holes in eight rows. Film cooling effectiveness is also computed on the adiabatic blade. Wilcox's k-omega model is used for modeling the turbulence. Of the eight rows of holes, three are staggered on the shower-head with compound-angled holes. With so many holes on the blade it was somewhat of a challenge to get a good quality grid on and around the blade and in the tip clearance region. The final multi-block grid consists of 4784 elementary blocks which were merged into 276 super blocks. The viscous grid has over 2.2 million cells. Each hole exit, in its true oval shape, has 80 cells within it so that coolant velocity, temperature, k and omega distributions can be specified at these hole exits. It is found that for the given parameters, heat transfer coefficient on the cooled, isothermal blade is highest in the leading edge region and in the tip region. Also, the effectiveness over the cooled, adiabatic blade is the lowest in these regions. Results for an uncooled blade are also shown, providing a direct comparison with those for the cooled blade. Also, the heat transfer coefficient is much higher on the shroud as compared to that on the hub for both the cooled and the uncooled cases.

Garg, Vijay K.↗

Xenon-Ion Drilling of Tungsten Films

High-velocity xenon ions used to drill holes of controlled size and distribution through tungsten layer that sheaths surface of controlled-porosity dispenser cathode of traveling wave-tube electron emitter. Controlled-porosity dispenser cathode employs barium/calcium/ aluminum oxide mixture that migrates through pores in cathode surface, thus coating it and reducing its work function. Rapid, precise drilling technique applied to films of other metals and used in other applications where micron-scale holes required. Method requires only few hours, as opposed to tens of hours by prior methods.

Garner, C. E.↗

Dilution jet mixing program, phase 3

The main objectives for the NASA Jet Mixing Phase 3 program were: extension of the data base on the mixing of single sided rows of jets in a confined cross flow to discrete slots, including streamlined, bluff, and angled injections; quantification of the effects of geometrical and flow parameters on penetration and mixing of multiple rows of jets into a confined flow; investigation of in-line, staggered, and dissimilar hole configurations; and development of empirical correlations for predicting temperature distributions for discrete slots and multiple rows of dilution holes.

Srinivasan, R.↗

The Imaging X-Ray Polarimetry Explorer (IXPE)

The Imaging X-ray Polarimetry Explorer (IXPE) is an exciting international collaboration for a scientific mission that dramatically brings together the unique talents of the partners to expand observation space by simultaneously adding polarization measurements to the array of source properties currently measured (energy, time, and location). IXPE uniquely brings to the table polarimetric imaging. IXPE will thus open new dimensions for understanding how X-ray emission is produced in astrophysical objects, especially systems under extreme physical conditions-such as neutron stars and black holes. Polarization singularly probes physical anisotropies-ordered magnetic fields, aspheric matter distributions, or general relativistic coupling to black-hole spin-that are not otherwise measurable. Hence, IXPE complements all other investigations in high-energy astrophysics by adding important and relatively unexplored information to the parameter space for studying cosmic X-ray sources and processes, as well as for using extreme astrophysical environments as laboratories for fundamental physics.

X-ray astronomy x-ray polarimetry↗

Solar polar coronal hole - A mathematical simulation

The northern polar region of the sun was studied during July 1973 by Munro and Jackson through use of the white-light coronagraph and the X-ray photographs produced by the Skylab mission. They described the northern polar hole as nearly axisymmetric and gave the geometry and density distribution under this approximation. The present work gives quasi-radial approximation to the full magnetohydrodynamic equations for axisymmetric, polytropic solar wind flow to simulate this polar hole, with the benefit that model temperature and magnetic field intensities and distributions in this particular polar hole can be deduced. It is concluded that from 2 out to 5 solar radii the temperature varies only slightly with radius, but is larger near the center of the polar hole than at the edge. It is also found that the magnetic field intensity at 2 solar radii could be about 1 gauss at the center of the hole, decreasing toward the edge of the hole. If this is extrapolated to the surface, a field as high as 20 gauss is suggested.

Suess, S. T.↗

Investigation of Spiral and Sweeping Holes

Surface infrared thermography, hotwire anemometry, and thermocouple surveys were performed on two new film cooling hole geometries: spiral/rifled holes and fluidic sweeping holes. The spiral holes attempt to induce large-scale vorticity to the film cooling jet as it exits the hole to prevent the formation of the kidney shaped vortices commonly associated with film cooling jets. The fluidic sweeping hole uses a passive in-hole geometry to induce jet sweeping at frequencies that scale with blowing ratios. The spiral hole performance is compared to that of round holes with and without compound angles. The fluidic hole is of the diffusion class of holes and is therefore compared to a 777 hole and Square holes. A patent-pending spiral hole design showed the highest potential of the non-diffusion type hole configurations. Velocity contours and flow temperature were acquired at discreet cross-sections of the downstream flow field. The passive fluidic sweeping hole shows the most uniform cooling distribution but suffers from low span-averaged effectiveness levels due to enhanced mixing. The data was taken at a Reynolds number of 11,000 based on hole diameter and freestream velocity. Infrared thermography was taken for blowing rations of 1.0, 1.5, 2.0, and 2.5 at a density ration of 1.05. The flow inside the fluidic sweeping hole was studied using 3D unsteady RANS.

infrared thermography↗

Toward Cooling Uniformity: Investigation of Spiral, Sweeping Holes, and Unconventional Cooling Paradigms

Surface infrared thermography, hotwire anemometry, and thermocouple surveys were performed on two new film cooling hole geometries: spiral/rifled holes and fluidic sweeping holes. Ways to quantify the efficacy of novel cooling holes that are asymmetric, not uniformly spaced or that show variation from hole to hole are presented. The spiral holes attempt to induce large-scale vorticity to the film cooling jet as it exits the hole to prevent the formation of the kidney shaped vortices commonly associated with film cooling jets. The fluidic sweeping hole uses a passive in-hole geometry to induce jet sweeping at frequencies that scale with blowing ratios. The spiral hole performance is compared to that of round holes with and without compound angles. The fluidic hole is of the diffusion class of holes and is therefore compared to a 777 hole and square holes. A patent-pending spiral hole design showed the highest potential of the nondiffusion type hole configurations. Velocity contours and flow temperature were acquired at discreet cross-sections of the downstream flow field. The passive fluidic sweeping hole shows the most uniform cooling distribution but suffers from low span-averaged effectiveness levels due to enhanced mixing. The data was taken at a Reynolds number of 11,000 based on hole diameter and freestream velocity. Infrared thermography was taken for blowing ratios of 1.0, 1.5, 2.0, and 2.5 at a density ratio of 1.05. The flow inside the fluidic sweeping hole was studied using 3D unsteady RANS. A section on ideas for future work is included that addresses issues of quantifying cooling uniformity and provides some ideas for changing the way we think about cooling such as changing the direction of cooling or coupling acoustic devices to cooling holes to regulate frequency.

Shyam, Vikram↗

The all-sky X-ray foreground - Outstanding issues

An all-sky X-ray foreground survey can be used to determine how supermassive black holes trace the underlying mass distribution responsible for the particular velocity of the local group. The dipole moment for the cosmic X-ray background is compared to that for the all-sky extragalactic foreground of discrete sources, and the survey of AGNs is determined to be an effective method for discerning pronounced large-scale foreground anisotropies. The required sensitivity for an all-sky survey of this type is found to be 3.3 x 10 to the -13th ergs/sq cm/s which would allow an unbiased AGN survey.

Boldt, Elihu↗

Reliability of stiffened structural panels: Two examples

The reliability of two graphite-epoxy stiffened panels that contain uncertainties is examined. For one panel, the effect of an overall bow-type initial imperfection is studied. The size of the bow is assumed to be a random variable. The failure mode is buckling. The benefits of quality control are explored by using truncated distributions. For the other panel, the effect of uncertainties in a strain-based failure criterion is studied. The allowable strains are assumed to be random variables. A geometrically nonlinear analysis is used to calculate a detailed strain distribution near an elliptical access hole in a wing panel that was tested to failure. Calculated strains are used to predict failure. Results are compared with the experimental failure load of the panel.

Stroud, W. Jefferson↗

The ionization of the diffuse ionized gas

The diffuse ionized gas (DIG), responsible for producing the faint but pervasive H(sub alpha), requires 15% of the power of all Galactic O stars for its ionization. No other source of ionization seems practical. The spectrum is strong in low stages of ionization (N II, SII), weak in (O III), and very weak in (O I) lambda 6300, at least in one well-observed direction, all significantly different from denser H II regions. We give low-density, low-excitation photoionization models that explain the observed spectrum. The lambda 6300 observation eliminates the simplest models for the DIG (Mathis 1986), in which neutral H extends beyond the edge of the very dilute stellar radiation field. Our present models include two components. One, representing the edges of interstellar H I clouds, extends to the point where H becomes neutral. In the second, the fraction of H(sup o) is not allowed to exceed 0.05 to 0.1. Both have very low values of the ionization parameter, or ratio of the number densities of ionizing photons to electrons. The ionization parameter required by our models is shown to be compatible with observed values of photon and electron densities in the diffuse interstellar medium. Interstellar dust is not important in either model. Predictions of the model are that the Galaxy is leaking about 4% of the ionizing radiation of at least the local O stars into the intergalactic medium, that (O II) lambda 3727 approximately equals 1.1 H(sub alpha), and that He(sup +)/H (sup +)) approximately equals 0.6 He/H. A major difficul ty of this picture is having ionizing radiation propagate from the ionizing stars in the plane of the Galaxy to the DIG. We suggest, as do Miller & Cox (1993), that the ionizing radiation from O stars produces holes or tunnels in the distribution of neutral H as seen from their positions, while we see a sky covered with H I sheets or filaments because we are not near a source of ionizing radiation. With our models, several interfaces between ionized and neutral gas are allowed before the observational limit on lambda 6300 is exceeded. Another difficulty is the gas-phase N(S(sup +))/N(H(sup o)) ratio toward the high-latitude star HD 93521 (Spitzer & Fitzpatrick 1993). We require (S/H) to be somewhat lower than solar, either because of depletion onto grains or a Galactic abundance gradient, so that the S(sup +) can be produced in each of separate H(sup o) and H(sup +) regions.

Domgorgen, H.↗

Hubble Space Telescope Planetary Camera observations of Arp 220

Planetary Camera images of peculiar galaxy Arp 220 taken with V, R, and I band filters reveal a very luminous object near the position of the western radio continuum source, assumed to be the major nucleus, ans seven lesser objects within 2 sec of this position. The most luminous object is formally coincident with the radio source to within the errors of Hubble Space Telescope (HST) pointing accuracy, but we have found an alternate, more compelling alignment of maps in which the eastern radio source coincides with one of the lesser objects and the OH radio sources reside near the surfaces of other optical objects. The proposed centering places the most luminous object 150 pc (0.4 sec) away from the western radio source. We explore the possibilities that the objects are either holes in the dense dust distribution, dusty clouds reflecting a hidden bright nucleus, or associations of bright young stars. We favor the interpretation that at least the brightest two objects are massive young star associations with luminosities 10(exp 9) to 10(exp 11) solar luminosity, but highly extinguished by intervening dust. These massive associations should fall into the nucleus on a time scale of 10(exp 8) yr. About 10% of the enigmatic far-IR flux arises from the observed objects. In addition, if the diffuse starlight out to a radius of 8 sec is dominated by stars with typical ages of order 10(exp 8) yr (the time since the alleged merger of two galaxies), as indicated by the blue colors at larger radius, then the lower limit to the reradiation of diffuse starlight contributes 3 x 10(exp 11) solar luminosity to the far-infrared flux, or greater than or equal to 25% of the total far-IR flux. Three additional bright objects (M(sub V) approximately equals -13) located about 6 sec from the core are likely young globular clusters, but any of these could be recently exploded supernovae instead. The expected supernovae rate, if the dominant energy source is young stars, is about one per month for the region where the intense far-infrared flux originates. Also, individual giant dust clouds are visible in these images. Their typical size is 300 pc (1 sec).

Shaya, Edward J.↗

Estimation of polar stratospheric cloud infrared extinction climatology using visible satellite observations

Polar stratospheric clouds (PSC's) provide surfaces for heterogeneous processes which can dramatically alter the normal partitioning of odd nitrogen and chlorine families in the winter polar stratospheres, setting up conditions for significant ozone depletion as manifested in the springtime Antarctic ozone hole. The spatial and temporal distribution of PSC's is important for parameterizing PSC occurrence in multidimensional photochemical models whose use is essential for fully understanding observed Antarctic ozone losses as well as for accessing the possibility of a similar phemonenon occurring in the future in the Arctic. The Stratospheric Aerosol Measurement (SAM) 2 sensor, a single-channel (1mu m) photometer launched into a Sun-synchronous orbit aboard the Nimbus 7 satellite in October 1978, provided a unique database to establish the climatology of PSC's. Poole and Pitts (1994) used the record of high-latitude aerosol extinction obtained by SAM II from 1979-1989 to establish the climatology of PSC occurrences in the Arctic and Antarctic. Unfortunately, little information about PSC composition or type was detectable from the single-wavelength SAM II data.

Pitts, Michael C.↗

Solar coronal hole simulations compared with interpretations of Yohkoh SXT observations

Recent observations of coronal holes made with the soft X-ray telescope aboard Yohkoh have indicated a temperature of 1.8 approximately 2.1 x 10(exp 6) K and an emission measure of 10(exp 25.7 approximately 26.2) cm (exp -5). This is almost the same as in quiet regions of the Sun. Numerical simulations of the temperature density and velocity structure in a coronal hole. using a parameterized heating distribution have been used for a comparison with the Yohkoh observations. Models are obtained which fit the observed temperature and emission measure. with heating fluxes which are consistent with other measurements. However, the final velocity of the solar wind is very slow which indicates the necessity of another acceleration mechanism such as alfven waves.

Tziotziou, K.↗

Measurement of Air Flow Characteristics Using Seven-Hole Cone Probes

The motivation for this work has been the development of a wake survey system. A seven-hole probe can measure the distribution of static pressure, total pressure, and flow angularity in a wind tunnel environment. The author describes the development of a simple, very efficient algorithm to compute flow properties from probe tip pressures. Its accuracy and applicability to unsteady, turbulent flow are discussed.

Takahashi, Timothy T.↗