SEARCH · Engineering Papers

Results for “Grain Growth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Improvements to the Powder Processing of near-Final Shape alnico Magnets

Alnico permanent magnets (PMs), a recent PM system of interest as an attractive rare earth-free PM alternative, have advantageous high operating temperature and magnetic saturation with the potential for utilization in electric machines, e.g. interior-PM motors found in electric vehicles, if current directional solidification methods can be replaced by a true mass production approach. Recently, two unique alnico compositions, termed Full-Co and Co-lean, with improved coercivity, were gas atomized, compression molded, and vacuum sintered (4h at 1240°C) to high densities of 97.8% and 99.3%, respectively. However, the Co-lean remained fine grained isotropic magnets and the Full-Co grains were not textured, lowering magnetic strength in spite of attempts to grow large textured grains by a stress-biased solid state grain alignment method to convert them to high energy anisotropic magnets. It was hypothesized that oxidation during de-binding in air left many prior particle boundary oxides within the sintered microstructure that hindered grain growth and texturing during the stress-biased texturing procedure and prevented the desired abnormal grain growth (AGG). Here we explored a vacuum de-binding step that was linked (in-place) to vacuum sintering and found that the Co-lean exhibited faster uniform grain growth that doubled the average grain size (40 μm to 80 μm). Linked vacuum de-binding and sintering of Full-Co produced some AGG after only 1 h of 1240°C sintering. A new direction for promoting AGG (and stress-biased texturing) in alnico is being explored that utilizes a fundamental analysis of systems with second phase particles that either inhibit or boost grain growth. This effort explores the influence of vacuum de-binding linked to a series of lower sintering temperatures at a fixed time (4h) to see if oxide particle size and volume fraction can be changed to promote AGG conditions in alnico. Surprising qualitative results indicate that AGG may be promoted for vacuum sintering at less than 1200°C.

Rinko, Emily↗

DOE OSTI2025

Scaling microstructural processes in the sintering of ionic ceramics

A multi-scale framework, combining a multiphase field formulation and large deformation mechanics, was developed as a stepping stone to perform the data analytics of the microstructural level kinetics of a sintering solid. Relevant microstructural information from this framework, such as grain, stress, and porosity statistics, was scaled up to describe the macroscopic level sintering kinetics. Here, the developed formulation was applied to describe the electric field assisted sintering of Y 2 O 3 . Microstructural inhomogeneities in a multi-granular solid result in the formation of a field of compressive stress networks, which interleave with low compression and weakly tensile regions, defining a scaffolding for sintering concentration regions to develop. A Poisson effect-induced lateral stress network is also naturally self-induced as a result of the mechanical constraints imposed by the sintering apparatus. For long sintering times, localized shear stresses enhancing mass flow along grain boundaries and internal surfaces develop. Three-sided pores are removed by either vacancy transport to the surrounding pores, or move towards the external surfaces through grain boundary diffusion. Four- and higher order-sided pores stabilize because an equal amount of vacancies are gained and lost through the connecting grain boundaries. Grain dewetting contributes to pore coalescence, suggesting that pore kinetics and grain growth are coupled and should be analyzed in concert. The combined sintering and grain growth kinetics define six regimes of sintering behavior: (1) T, the transient regime; (2) E$_Υ$, the surface energy dominated, early sintering regime, where the grain growth exponent, p = 1, and the stress concentration factor, $f$ ~ $1/\hat{ρ}^{4.6}$; (3) E S , the stress dominated, early sintering regime, where p = 1 and $f$ ~ $1/\hat{ρ}^{4}$; (4) I$_Υ$, the surface energy dominated, intermediate sintering regime, where p = 2 and $f$ ~ $1/\hat{ρ}^{4.6}$; (5) I S , the stress dominated, intermediate sintering regime, where p = 2 and $f$ ~ $1/\hat{ρ}^{4}$; and (6) L, the late sintering regime, where p = 3 and $f$ ~ 1. At the macroscopic level, the rapid densification and suppression of grain growth observed in the electric field assisted sintering process is a consequence of the compounding effects of the underlying stress-, transport-, and interfacial-energy-induced energy minimization kinetics, as predicted by the multi-scale framework.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1990

Lifetime studies of high power rhodium/tungsten and molybdenum electrodes for application to AMTEC (alkali metal thermal-to-electric converter)

A detailed and fundamental model for the electrochemical behavior of AMTEC electrodes is developed which can aid in interpreting the processes which occur during prolonged operation of these electrodes. Because the sintering and grain growth of metal particles is also a well-understood phenomenon, the changes in electrode performance which accompany its morphological evolution may be anticipated and modeled. The grain growth rate observed for porous Mo AMTEC electrodes is significantly higher than that predicted from surface diffusion data obtained at higher temperatures and incorporated into the grain growth model. The grain growth observed under AMTEC conditions is also somewhat higher than that measured for Mo films on BASE (beta-alumina solid electrolyte) substrates in vacuum or at similar temperatures. Results of modeling indicate that thin Mo electrodes may show significant performance degradation for extended operation (greater than 10,000 h) at higher operating temperatures (greater than 1150 K), whereas W/Rh and W/Pt electrodes are expected to show adequate performance at 1200 K for lifetimes greater than 10,000 h. It is pointed out that current collection grids and leads must consist of refractory metals such as Mo and W which do not accelerate sintering or metal migration.

Williams, R. M.↗

DOE OSTI2022

Powder Metallurgy HIP Process Study and Mechanical Property Evaluations for IN740H

The effects of hot isostatic pressing (HIP) parameters and powder size distribution (PSD) on the resulting microstructure and properties of powder metallurgy (P/M) IN740H have been investigated. Properties can be substantially tailored through the appropriate management of these parameters. Applying a thermal presoak to the input powder prior to the sintering stage of HIP can significantly increase average grain size and coarse grain fraction, enabling a trade for improved creep resistance at the expense of tensile strength. Here, powder thermal presoak was found to have a larger impact on microstructure and properties than the use of a coarser PSD alone. Additionally, substantial grain growth and grain boundary migration is observed in P/M IN740H at HIP temperatures above 1260°C. Given its inherently finer grain size, P/M HIP IN740H typically outperforms its cast and wrought counterparts in tensile response. Creep life at 700–800°C was inferior to wrought due to PPBs coincident with grain boundaries which served as cavity nucleation sites, leading to lower creep ductility. The ability to adjust the microstructure toward a more balanced creep and tensile behavior allows P/M HIP IN740H to be considered for high-temperature applications in advanced ultra-supercritical steam and supercritical carbon dioxide power cycles.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Diffusion bonded compact heat exchanger in Inconel 740H for high temperature and high-pressure applications

It is desired to develop heat exchangers able to be operated at high temperatures (750°C) and pressures (3636 psi) for use in advanced Brayton power cycle. Conventional materials have not had the high strength at temperature required for these applications previously, however a fairly new material Inconel 740H developed by Special Metals for the ultra-supercritical water fossil industry has shown good performance under these conditions. In further efforts to capitalize on these new high strength high temperature alloys CompRex has developed a diffusion bonding procedure capable of alloying compact high effectiveness heat exchangers that can perform under these high temperature and high-pressure conditions. Initial tests of the heat exchanger are being conducted at the University of Wisconsin using supercritical CO2 working fluid. The bonding process has been adjusted such that the strength of the bonded block has achieved over 90% yield and tensile strength of the 740H base material values. Grain size before and after bonding were measured to determine the extent of grain growth and grain diffusion across the interface. A discussion of the heat exchanger design, etching and initial tensile tests on sample bonds will be discussed.

14 SOLAR ENERGY↗

DOE OSTI2022

Diffusion bonded compact heat exchanger in Inconel 740H for high temperature and high-pressure applications

It is desired to develop heat exchangers able to be operated at high temperatures (750˚C) and pressures (3636 psi) for use in advanced Brayton power cycle. Conventional materials have not had the high strength at temperature required for these applications previously, however a fairly new material Inconel 740H developed by Special Metals for the ultra-supercritical water fossil industry has shown good performance under these conditions. In further efforts to capitalize on these new high strength high temperature alloys CompRex has developed a diffusion bonding procedure capable of alloying compact high effectiveness heat exchangers that can perform under these high temperature and high-pressure conditions. Initial tests of the heat exchanger are being conducted at the University of Wisconsin using supercritical CO2 working fluid. The bonding process has been adjusted such that the strength of the bonded block has achieved over 90% yield and tensile strength of the 740H base material values. Grain size before and after bonding were measured to determine the extent of grain growth and grain diffusion across the interface. A discussion of the heat exchanger design, etching and initial tensile tests on sample bonds will be discussed.

14 SOLAR ENERGY↗

DOE OSTI2021

Anomalous strain-energy-driven macroscale translation of grains during nonisothermal annealing

We report a mode of grain growth, involving the macroscopic translation of grain centers during nonisothermal annealing. Through synchrotron high-energy x-ray diffraction microscopy, we find dissolution of semicoherent precipitates generates dislocations, thereby raising the stored strain energy within grains. Here, the subsequent evolution of grains shows unexpected grain translations over length scales of 10-100 mu m. Phase-field simulations reveal that such translations are not uncommon in strain-energy-driven grain growth, wherein different regions of a grain may grow and shrink simultaneously.

36 MATERIALS SCIENCE↗

DOE OSTI2023

An Integrated Simulation of Multiple-Pass U-10Mo Alloy Hot Rolling and Static Recrystallization

To achieve a desired microstructure and minimize the thickness variation in rolled foils, researchers must understand the effects of foil fabrication process variables on microstructure evolution. We developed an integrated simulation of deformation and recrystallization that employs the finite element method (FEM) and the kinetic Monte Carlo (KMC) Potts model, respectively, to investigate microstructure evolution during multiple-pass hot rolling and heat treatment in polycrystalline U-10Mo fuel. Scanning electron microscopy and electron backscatter diffraction images of microstructures were directly used as input in FEM calculation of deformation, and the calculated strains were used to determine the driving force of nucleation and growth of recrystallized grains in the Potts model. Grain structures predicted by the Potts model were used to update the grain structure and material properties for FEM. Simulation alternated between FEM and the Potts model to simulate grain structure evolution during multiple rolling and heat treatments. The initial model parameters were determined by benchmarking the recrystallization kinetics against experimental data. Then, the model was applied to predict the grain structure evolution. Results showed that our model can capture the coupling between deformation and recrystallization and can quantitatively reproduce the observed U-10Mo recrystallization and grain growth kinetics. The simulation results demonstrated that the developed model can predict U-10Mo grain structures as a function of initial microstructure and foil fabrication parameters.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Sodium doping of solution-processed amine-thiol based CIGS solar cells by thermal evaporation of NaCl

Poor crystallinity, high degree of porosity and rough surfaces are the main drawbacks of solution-processed CIGS absorbers resulting in lower power conversion efficiencies when compared to vacuum-based CIGS solar cells. Therefore, promoting absorber grain growth is key to further improve solution-based solar cell performance. The effect of alkali elements such as Na in CIGS absorbers is generally recognised to have beneficial effects not only on the absorber opto-electronic properties but also on the grain growth. In this work, thermal evaporation of a thin layer of NaCl prior to selenisation resulted in absorbers with significantly larger CIGS grains than previously seen with Na diffusing directly from the from soda-lime glass substrate. NaCl is non-toxic, abundant and readily available compound that has not been typically used as an evaporation source, but rather as an additive into CIGS precursor solution. The effect of Na on these solution-processed CIGS devices was primarily observed in the spectacular morphological changes leading to improved carrier collection and minority carrier lifetimes, but less on the absorber doping. Transmission electron microscopy (TEM) revealed voids forming around large CIGS grains upon NaCl addition and these had a negative effect on inter-grain carrier transport. Nonetheless, the resulting device performance doubled from 5% to 10% with addition of Na using this doping approach; however, a compromise between the optimum grain growth and optimum electronic properties had to be made. This study demonstrates a novel, simple and effective Na-doping strategy for CIGS absorbers and reveals the current limitations of the Na-doping in solution-processed atmospherically deposited cells.

14 SOLAR ENERGY↗

NASA NTRS2019

High temperature electric arc furnace and method

An apparatus and process for improving the microstructure of electrically conducting materials is disclosed by the present invention. A revolving heat source applies heat to the surface of the material evenly and quickly. One or more heat sinks quickly cool the material. In the preferred embodiment, the cooling may be done in such a way as to promote as high a degree of directional grain growth as desired or completely nondirectional grain growth.

Richard M Poorman↗

NASA NTRS1985

The effects of surface finish and grain size on the strength of sintered silicon carbide

The effects of surface treatment and microstructure, especially abnormal grain growth, on the strength of sintered SiC were studied. The surfaces of sintered SiC were treated with 400, 800 and 1200 grit diamond wheels. Grain growth was induced by increasing the sintering times at 2050 C. The beta to alpha transformation occurred during the sintering of beta-phase starting materials and was often accompanied by abnormal grain growth. The overall strength distributions were established using Weibull statistics. The strength of the sintered SiC is limited by extrinsic surface flaws in normal-sintered specimens. The finer the surface finish and grain size, the higher the strength. But the strength of abnormal sintering specimens is limited by the abnormally grown large tabular grains. The Weibull modulus increases with decreasing grain size and decreasing grit size for grinding.

You, Y. H.↗

DOE OSTI2023

Gradient nanostructuring via compositional means

Nanocrystalline metals are inherently unstable against thermal and mechanical stimuli, commonly resulting in significant grain growth. Also, while these metals exhibit substantial Hall-Petch strengthening, they tend to suffer from low ductility and fracture toughness. With regard to the grain growth problem, alloying elements have been employed to stabilize the microstructure through kinetic and/or thermodynamic mechanisms. And to address the ductility challenge, spatially-graded grain size distributions have been developed to facilitate heterogeneous deformation modes: high-strength at the surface and plastic deformation in the bulk. In the present work, we combine these two strategies and present a new methodology for the fabrication of gradient nanostructured metals via compositional means. Here, we have demonstrated that annealing a compositionally stepwise Pt-Au film with a homogenous microstructure results in a film with a spatial microstructural gradient, exhibiting grains which can be twice as wide in the bulk compared to the outer surfaces. Additionally, phase-field modeling was employed for the comparison with experimental results and for further investigation of the competing mechanisms of Au diffusion and thermally induced grain growth. This fabrication method offers an alternative approach for developing the next generation of microstructurally stable gradient nanostructured films.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Enhancing Crystallization in Hybrid Perovskite Solar Cells Using Thermally Conductive 2D Boron Nitride Nanosheet Additive

Controlling crystallization and grain growth is crucial for realizing highly efficient hybrid perovskite solar cells (PSCs). In this work, enhanced PSC photovoltaic performance and stability by accelerating perovskite crystallization and grain growth via 2D hexagonal boron nitride (hBN) nanosheet additives incorporated into the active perovskite layer are demonstrated. Specifically, in situ X-ray scattering and infrared thermal imaging during the perovskite annealing process revealed the highly thermally conductive hBN nanosheets promoted the phase conversion and grain growth in the perovskite layer by facilitating a more rapid and spatially uniform temperature rise within the perovskite film. Complementary structural, physicochemical, and electrical characterizations further showed that the hBN nanosheets formed a physical barrier at the perovskite grain boundaries and the interfaces with charge transport layers, passivating defects, and retarding ion migration. As a result, the power conversion efficiency of the PSC is improved from 17.4% to 19.8%, along with enhanced device stability, retaining ≈90% of the initial efficiency even after 500 h ambient air storage. Here, the results not only highlight 2D hBN as an effective additive for PSCs but also suggest enhanced thermal transport as one of the pathways for improved PSC performance by 2D material additives in general.

2D materials↗

DOE OSTI2020

The Effects of Annealing after Equal Channel Angular Extrusion (ECAE) on Mechanical and Magnetic Properties of 49Fe-49Co-2V Alloy

Equal channel angular extrusion (ECAE) of 49Fe-49Co-2V, also known as Hiperco® 50A or Permendur-2V, greatly improves the strength and ductility of this alloy, while sacrificing soft magnetic performance. In this work, ECAE Hiperco specimens were subjected to post-ECAE annealing in order to improve soft magnetic properties. The microstructure, mechanical properties, and magnetic performance are summarized in this study. Annealing begins above 650°C and a steep decline in yield strength is observed for heat treatments between 700 and 840°C due to grain growth and the Hall-Petch effect, although some strength benefit is still observed in fully annealed ECAE material compared to conventionally processed bar. Soft magnetic properties were assessed through B-H hysteresis curves from which coercivity (Hc) values were extracted. Hc decreases rapidly with annealing above 650°C as well, i.e. improved soft magnetic behavior. The observed trend is attributed to annealing and grain growth in this temperature regime, which facilitates magnetic domain wall movement. The coercivity vs. grain size results generally follow the trend predicted in the literature. The magnetic behavior of annealed ECAE material compares favorably to conventional bar, possibly due to mild crystallographic texturing which enhances properties in the post-ECAE annealed material. Overall, this study highlights a definitive tradeoff between mechanical and magnetic properties brought about by post-ECAE annealing and grain growth.

annealing↗

DOE OSTI2020

Recrystallization suppression through dispersion-strengthening of tungsten

Tungsten is the material of choice for the divertor region of future nuclear fusion reactors, an environment that will expose plasma-facing components (e.g. divertor, etc...) to high temperatures and transient high heat flux events. Under these conditions, recrystallization and grain growth of tungsten can occur, leading to undesirable microstructural and mechanical property changes. Therefore, there is a need to raise the recrystallization temperature of tungsten and limit the kinetics of the recrystallization and grain growth processes. In this work, we examine the effect of different types (TiC vs. TaC vs. ZrC) and different concentrations (1.1 vs. 5 vs. 10 wt.%) of dispersed second phase particles in a tungsten matrix on the high temperature performance. Additionally, the addition of second-phase particles effectively increases the temperature of and time for recrystallization and slow grain growth; however, the addition of a high weight fraction of particles alters the surface chemistry, which may impact subsequent plasma-surface interactions. These results show that the addition of small concentrations of dispersed particles can be effectively employed in tungsten to raise the upper operating temperature limit for tungsten in a fusion reactor.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Uncovering grain and subgrain microstructure at the scale of additive manufacturing melt tracks with a scalable cellular automaton solidification model

Metal additive manufacturing, characterized by rapid solidification, yields refined grains with a distinctive cellular subgrain microstructure that plays a pivotal role in determining material properties. Due to the significant computational expense demanded to simulate the required physics with submicron spatial resolution, their numerical simulations have been limited to proof-of-concept studies to either 2D or small subregions of a melt pool. In this study, an open-source, scalable, solidification code, muMatScale, based on the cellular automaton method, has been developed to predict the grain and the underlying subgrain microstructure over an entire melt pool. The model incorporates flexible parallelization schemes, utilizing MPI and OpenMP GPU Offloading, in addition to appropriate multi-physics specific to non-equilibrium rapid solidification in AM. The impact of nucleation parameters on grain microstructures was investigated with a focus on grain size variations and morphology transitions. With selected nucleation parameters, the simulation predicted the grain size, subgrain morphology, crystallographic orientation, and microsegregation aligned with experimental measurements. The model demonstrates that epitaxial grain growth is a dominant factor at the melt pool boundary, influencing grain size variation under different grain sizes in the build plate while maintaining consistent primary dendrite arm spacing under identical thermal conditions. Here, the highly efficient numerical model enables large-scale simulations with a spatial resolution of 100 nm or less, unveiling unprecedented insights into thermal and solutal diffusion driven grain growth, and the subgrains with microsegregation within grains in 3D across scales. muMatScale will enable the linking of submicron length-scale microstructure to part-level material behavior by investigating fundamental solidification problems at the intercellular scale in many-track and many-layer builds.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Development of High-Quality, Very Large-Grained Cd(Se,Te) Thin Films for CdTe Solar Modules (Final Technical Report)

TCF-21-25048 is a one-year project to quantify the potential attributes of recent NREL inventions where CdTe devices with grain sizes exceeding 100's of microns in lateral dimension can be fabricated using a novel seeded-epitaxial process. A CdSe0.1Te0.9 film is evaporated on commercially available transparent conducting oxide (TCO) where the latter surface roughness (Ra) has been reduced to < 1-nm. After NREL's colossal grain growth (CGG) process, the grain size of this "seed" layer is increased to 100-1000 um. CdTe is then deposited epitaxially resulting in a large-grain CdTe device structure without use of CdCl2. As of this report, we have: Demonstrated the feasibility of using Tec-15 substrates after surface roughness (Ra) reduction (nexTC); Developed reproducible CGG processes for this commercially available substrate; Developed a close-spaced sublimation (CSS) process for CdTe epitaxy using these substrates; Demonstrated that large-grain CdTe films have less sub-band (band tail) absorption than conventional, small-grain CdTe; Demonstrated that large-grain CdTe films (no CdCl2) have carrier lifetimes up to 1.5 ns; Demonstrated that carrier lifetimes in epi-CdTe films (no CdCl2) have comparable lifetimes when compared to the best pX-CdTe films (FSLR) treated with CdCl2; Started making large-grain CdTe devices using CGG templates and epitaxially deposited CdTe.

14 SOLAR ENERGY↗

NASA NTRS1980

Recrystallization characteristics of oxide dispersion strengthened nickel-base alloys

Electron microscopy was employed to study the process of recrystallization in two oxide dispersion strengthened (ODS) mechanically alloyed nickel-base alloys, MA 754 and MA 6000E. MA 754 contained both fine, uniformly dispersed particles and coarser oxides aligned along the working direction. Hot rolled MA 754 had a grain size of 0.5 microns and high dislocation densities. After partial primary recrystallization, the fine grains transformed to large elongated grains via secondary (or abnormal) grain growth. Extruded and rolled MA 6000E contained equiaxed grains of 0.2 micron diameter. Primary recrystallization occurring during working eliminated virtually all dislocations. Conversion from fine to coarse grains was triggered by gamma prime dissolution; this was also a process of secondary or abnormal grain growth. Comparisons were made to conventional and oxide dispersion strengthened nickel-base alloys.

Hotzler, R. K.↗