Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Gas Turbine Combustor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Mixing of multiple dilution jets with a hot primary airstream for gas turbine combustors

The mixing of multiple air jets with a subsonic heated crossflow in a constant area duct was studied experimentally. The jet-to-mainstream momentum flux ratio was varied from 6 to 60. Temperature and pressure surveys were made at several downstream locations for orifice geometries with parametric variation of orifice size and spacing. A mixing efficiency parameter was defined which characterized the effectiveness of the mixing over the range of conditions examined. It was found that for a given momentum flux ratio, there exists a ratio of orifice spacing to duct height which provides the best mixing.

Holdeman, J. D.↗
NASA NTRS1977

Experimental and analytical separation of hydrodynamic, entropy and combustion noise in a gas turbine combustor

This paper deals with noise sources which are central to the problem of core engine noise in turbopropulsion systems. The sources dealt with are entropy noise and direct combustion noise, as well as a non-propagating psuedosound which is hydrodynamic noise. It is shown analytically and experimentally that a transition can occur from a combustion noise dominant situation to an entropy noise dominant case if the contraction of a terminating nozzle to the combustor is high enough. In the combustor tested, entropy noise is the dominant source for propagational noise if the combustor is choked at the exit. Analysis techniques include spectral, cross spectral, cross correlation, and ordinary and partial coherence analysis. Measurements include exterior and interior fluctuating and mean pressures and temperatures.

Muthukrishnan, M.↗
NASA NTRS1980

Study of research and development requirements of small gas-turbine combustors

A survey is presented of the major small-engine manufacturers and governmental users. A consensus was undertaken regarding small-combustor requirements. The results presented are based on an evaluation of the information obtained in the course of the study. The current status of small-combustor technology is reviewed. The principal problems lie in liner cooling, fuel injection, part-power performance, and ignition. Projections of future engine requirements and their effect on the combustor are discussed. The major changes anticipated are significant increases in operating pressure and temperature levels and greater capability of using heavier alternative fuels. All aspects of combustor design are affected, but the principal impact is on liner durability. An R&D plan which addresses the critical combustor needs is described. The plan consists of 15 recommended programs for achieving necessary advances in the areas of liner thermal design, primary-zone performance, fuel injection, dilution, analytical modeling, and alternative-fuel utilization.

Demetri, E. P.↗
NASA NTRS1980

Smoke characteristics of distillate and residual fuel burning in gas turbine combustors

During the development of a rich-lean staged dry low NOx combustor, the conventional trend of increasing smoke with increasing operating equivalence ratio was found when tests were run with distillate fuel (% H = 13.0). However, when tests were run with residual fuel (% H = 11.4), the trend was reversed. In addition, when the same combustor was run with blends of distillate fuel and residual fuel, a drastic improvement of smoke was observed when only 6 percent of residual fuel was mixed with distillate fuel, and for any blending of more than 10 percent of residual fuel the combustor was practically smoke free. A chemical analysis of fuel samples revealed an appreciable amount of trace metals in the residual fuel, giving rise to the suspicion that the smoke reduction may have been due in part to these trace metals. Of these elements found, vanadium is believed to be the most likely to cause smoke reduction because of its relatively high concentration.

Liu, T. M.↗
NASA NTRS1981

Design and preliminary results of a fuel flexible industrial gas turbine combustor

The design characteristics are presented of a fuel tolerant variable geometry staged air combustor using regenerative/convective cooling. The rich/quench/lean variable geometry combustor is designed to achieve low NO(x) emission from fuels containing fuel bound nitrogen. The physical size of the combustor was calculated for a can-annular combustion system with associated operating conditions for the Allison 570-K engine. Preliminary test results indicate that the concept has the potential to meet emission requirements at maximum continuous power operation. However, airflow sealing and improved fuel/air mixing are necessary to meet Department of Energy program goals.

Novick, A. S.↗
NASA NTRS1981

Static strain measurements on gas turbine combustor liners

It is noted that the combustor, a critical hot section component, can suffer failure through crack formation, buckling, and liner burn-through. Thus, there is a need to develop instrumentation which can function reliably in the combustor liner environment during testing and provide data to verify the accuracy of the analytical predictive tools used in designing the combustors. The results of an investigation into the suitability of a number of resistive, capacitive, optical, and electronic sensors are presented. The three sensors judged to possess the potential for measuring static strains up to + or - 2,000 micro-strain at temperatures to 1150 K with an accuracy of + or - 10% are the Kanthal A-1 Wire Strain Gage, Speckle Photography with Heterodyne Halo Evaluation, and the Thin Film Capacitive Sensor.

Raymondo, P.↗
NASA NTRS1982

Techniques for enhancing durability and equivalence ratio control in a rich-lean, three-stage ground power gas turbine combustor

Rig tests of a can-type combustor were performed to demonstrate two advanced ground power engine combustor concepts: steam cooled rich-burn combustor primary zones for enhanced durability; and variable combustor geometry for three stage combustion equivalence ratio control. Both concepts proved to be highly successful in achieving their desired objectives. The steam cooling reduced peak liner temperatures to less than 800 K. This offers the potential of both long life and reduced use of strategic materials for liner fabrication. Three degrees of variable geometry were successfully implemented to control airflow distribution within the combustor. One was a variable blade angle axial flow air swirler to control primary airflow while the other two consisted of rotating bands to control secondary and tertiary or dilution air flow.

Schultz, D. F.↗
NASA NTRS1982

Computations of soot and and NO sub x emissions from gas turbine combustors

An analytical program was conducted to compute the soot and NOx emissions from a combustor and the radiation heat transfer to the combustor walls. The program involved the formulation of an emission and radiation model and the incorporation of this model into the Garrett 3-D Combustor Perfomance Computer Program. Computations were performed for the idle, cruise, and take-off conditions of a JT8D can combustor. The predicted soot and NOx emissions and the radiation heat transfer to the combustor walls agree reasonably well with the limited experimental data available.

Srivatsa, S. K.↗
NASA NTRS1983

Small gas turbine combustor study - Combustor liner evaluation

A reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) is compared both analytically and experimentally with a conventional splash film-cooled design with the same combustor configuration. Comparison of selected critical combustor panels indicated that it was possible to maintain the liner temperature similar between the two configurations using 50 percent less coolant for the Lamilloy as compared with the reference film-cooled combustor. Additional benefits indicated improvement in outlet temperature distribution and NOx emission level.

Norgren, C. T.↗
NASA NTRS1983

Effects of broadened property fuels on radiant heat flux to gas turbine combustor liners

The effects of fuel type, inlet air pressure, inlet air temperature, and fuel/air ratio on the combustor radiation were investigated. Combustor liner radiant heat flux measurements were made in the spectral region between 0.14 and 6.5 microns at three locations in a modified commercial aviation can combustor. Two fuels, Jet A and a heavier distillate research fuel called ERBS were used. The use of ERBS fuel as opposed to Jet A under similar operating conditions resulted in increased radiation to the combustor liner and hence increased backside liner temperature. This increased radiation resulted in liner temperature increases always less than 73 C. The increased radiation is shown by way of calculations to be the result of increased soot concentrations in the combustor. The increased liner temperatures indicated can substantially affect engine maintenance costs by reducing combustor liner life up to 1/3 because of the rapid decay in liner material properties when operated beyond their design conditions.

Haggard, J. B., Jr.↗
NASA NTRS1984

Influence of fuel chemical properties on gas turbine combustors

In an attempt to rigorously study the fuel chemical property influence, UTRC (United Technologies Research Center) (under contract to NASA Lewis Research Center) has conducted an experimental program using 25 test fuels. The burner was a 12.7 cm dia cylindrical device consisting of six sheet metal louvers. A single pressure atomizing injector and air swirler were centrally mounted with the conical dome. Fuel physical properties were de-emphasized by using fuel injectors which produced highly atomized, and hence rapidly vaporizing sprays. A substantial fuel spray characterization effort was conducted to allow selection of nozzles which assured that such sprays were achieved for all fuels. The fuels were specified to cover the following wide ranges of chemical properties: hydrogen, 9.1 to 15 (wt) pct; total aromatics, 0 to 100 (vol) pct; and naphthalene, 0 to 30 (vol) pct. They included standard fuel (e.g., Jet A, JP4), specialty products (e.g., decalin, xylene tower bottoms) and special fuel blends. Included in this latter group were six, 4-component blends prepared to achieve parametric variations in fuel hydrogen, total aromatics and naphthalene contents.

Rosfjord, T. J.↗
NASA NTRS1985

Small gas turbine combustor study: Fuel injector performance in a transpiration-cooled liner

The effect of fuel injection technique on the performance of an advanced reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) was determined. Performance and emission levels are documented over a range of simulated flight conditions using simplex pressure atomizing, spill return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types is obtained.

Riddlebaugh, S. M.↗
NASA NTRS1985

Small gas turbine combustor study - Fuel injector performance in a transpiration-cooled liner

The effect of fuel injection technique on the performance of an advanced reverse flow combustor liner constructed of Lamilloy (a multilaminate transpiration type material) was determined. Performance and emission levels are documented over a range of simulated flight conditions using simplex pressure atomizing, spill return, and splash cone airblast injectors. A parametric evaluation of the effect of increased combustor loading with each of the fuel injector types is obtained.

Riddlebaugh, S. M.↗
NASA NTRS1985

Prediction of the structure of fuel sprays in gas turbine combustors

The structure of fuel sprays in a combustion chamber is theoretically investigated using computer models of current interest. Three representative spray models are considered: (1) a locally homogeneous flow (LHF) model, which assumes infinitely fast interphase transport rates; (2) a deterministic separated flow (DSF) model, which considers finite rates of interphase transport but ignores effects of droplet/turbulence interactions; and (3) a stochastic separated flow (SSF) model, which considers droplet/turbulence interactions using random sampling for turbulence properties in conjunction with random-walk computations for droplet motion and transport. Two flow conditions are studied to investigate the influence of swirl on droplet life histories and the effects of droplet/turbulence interactions on flow properties. Comparison of computed results with the experimental data show that general features of the flow structure can be predicted with reasonable accuracy using the two separated flow models. In contrast, the LHF model overpredicts the rate of development of the flow. While the SSF model provides better agreement with measurements than the DSF model, definitive evaluation of the significance of droplet/turbulence interaction is not achieved due to uncertainties in the spray initial conditions.

Shuen, J. S.↗
NASA NTRS1986

Prediction of the structure of fuel sprays in gas turbine combustors

The structure of fuel sprays in a combustion chamber is theoretically investigated using computer models of current interest. Three representative spray models are considered: (1) a locally homogeneous flow (LHF) model, which assumes infinitely fast interphase transport rates; (2) a deterministic separated flow (DSF) model, which considers finite rates of interphase transport but ignores effects of droplet/turbulence interactions; and (3) a stochastic separated flow (SSF) model, which considers droplet/turbulence interactions using random sampling for turbulence properties in conjunction with random-walk computations for droplet motion and transport. Two flow conditions are studied to investigate the influence of swirl on droplet life histories and the effects of droplet/turbulence interactions on flow properties. Comparison of computed results with the experimental data show that general features of the flow structure can be predicted with reasonable accuracy using the two separated flow models. In contrast, the LHF model overpredicts the rate of development of the flow. While the SSF model provides better agreement with measurements than the DSF model, definitive evaluation of the significance of droplet/turbulence interaction is not achieved due to uncertainties in the spray initial conditions.

Shuen, J.-S.↗
NASA NTRS1991

Effects of nozzle lip geometry on spray atomization and emissions advanced gas turbine combustors

A parametric study is conducted to investigate the effect of nozzle lip geometry on nozzle fuel distribution, emissions and temperature distribution for a rich burn section of a rich burn/quick quench/lean burn combustor. It is seen that the nozzle lip geometry greatly affects the fuel distribution, emissions and temperature distribution. It is determined that at an equivalence ratio of 1.6 the NO concentration could be lowered by a factor greater than three by changing the nozzle lip geometry.

Micklow, Gerald J.↗