Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GASIFICATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Influence of Pelletization and Moisture Content of Oil Palm Empty Fruit Bunches (EFBs) on Dynamic Gasification Performance

Wet-ground empty fruit bunches (EFBs), dry-ground EFB, and pelletized EFB were gasified in a laboratory-scale updraft fixed-bed reactor at differing temperatures and equivalent ratios (ERs) between 0.19 and 0.78 to evaluate the performance and quality of the syngas under autothermal operating conditions. In addition, the theoretical estimation of the key performance indicator of the ashes on the performance of the gasification process was obtained. The results show that for ERs > 0.4 the autothermal operating condition was achieved for pretreatments with pelletized and dry-ground EFBs, with reactor operating temperatures T > 700 °C. With wet EFB, this condition is achieved at any ER value. The average composition of the syngas from pelletized EFB presented the best average concentrations of the combustible species CO, H2, and CH4 when the ER values were between 0.25 and 0.40. The highest hot and cold thermal efficiency values were obtained for the gasification of EFB pellets with ER values between 0.25 and 0.40. For ground EFB, increases in the ER value led to improvements in hot thermal efficiency. Finally, during the EFB pellet gasification tests, no agglomeration and sintering problems were evidenced in comparison with wet-ground and dry-ground EFBs that showed slag formation, especially at ER < 0.46.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Catalytic steam gasification reactivity of HyperCoals produced from different rank of coals at 600-775{degree}C

HyperCoal is a clean coal with ash content <0.05 wt %. HyperCoals were prepared from a brown coal, a sub-bituminous coal, and a bituminous raw coal by solvent extraction method. Catalytic steam gasification of these HyperCoals was carried out with K{sub 2}CO{sub 3} at 775, 700, 650, and 600 {degree}C, and their rates were compared. HyperCoals produced from low-rank coals were more reactive than those produced from the high-rank coals. XRD measurements were carried out to understand the difference in gasification reactivity of HyperCoals. Arrhenius plot of ln (k) vs 1/T in the temperature range 600-825{degree}C was a curve rather than a straight line. The point of change was observed at 700{degree}C for HyperCoals from low-rank coals and at 775{degree}C for HyperCoals from high-rank coals. Using HyperCoal produced from low-rank coals as feedstock, steam gasification of coal may be possible at temperatures less than 650{degree}C. 22 refs., 6 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

High-level computer molecular modeling for low-rank coal containing metal complexes and iron-catalyzed steam gasification

Low-rank coal is a complex mixture; consequently, it is necessary to develop simpler molecular representations for computational modeling. Our modeling objective has been to develop molecules suitable for semi-empirical (SE) computations of low-rank coal containing transition-metal complexes. These molecular models contain oxygen functional groups that are macro-ligands, forming coordination complexes with specific three-dimensional (3D) orientations; consequently, we develop models that encapsulate the properties of low-rank coals and can form metal complexes. The large computer resources required for SE calculations of these molecules limited their size; of the models examined, those containing numerous short links between phenyl groups caused excessive strain and were unsuitable to model transition-metal complexes. Computations (SE) of our models provided data on (i) hydrogen bonds of coal containing water, (ii) formation of aqua-inorganic species and transition-metal complexes, (iii) pyrolysis chemistry involving transformations of metal hydroxide/oxides, (iv) routes for H{sub 2} and CO formation, and (v) mechanism of iron-catalyzed steam gasification. Our char models, on the basis of transformations of the coal model, were consistent with low-temperature pyrolysis; these were disordered structures with some phenyl groups spaced between 0.35 and 0.4 nm. Smaller models of char and chars containing transition-metal clusters were optimized with SE and density functional theory (DFT) computations; these models were useful in modeling the mechanism of catalytic steam gasification. Our modeling of the mechanisms of iron-catalyzed steam gasification was consistent with experimental data. 44 refs., 5 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Gasification of refinery sludge in an updraft reactor for syngas production

The study probes into the investigation on gasification of dry refinery sludge. The details of the study includes; influence of operation time, oxidation temperature and equivalence ratios on carbon gas conversion rate, gasification efficiency, heating value and fuel gas yield are presented. The results show that, the oxidation temperature increased sharply up to 858°C as the operating time increased up to 36 min then bridging occurred at 39 min which cause drop in reaction temperature up to 819 °C. This bridging was found to affect also the syngas compositions, meanwhile as the temperature decreased the CO, H{sub 2}, CH{sub 4} compositions are also found to be decreases. Higher temperature catalyzed the reduction reaction (CO{sub 2}+C = 450 2CO), and accelerated the carbon conversion and gasification efficiencies, resulted in more solid fuel is converted to a high heating value gas fuel. The equivalence ratio of 0.195 was found to be the optimum value for carbon conversion and cold gas efficiencies, high heating value of gas, and fuel gas yield to reach their maximum values of 96.1 % and 53.7 %, 5.42 MJ Nm{sup −3} of, and 2.5 Nm{sup 3} kg{sup −1} respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of small-scale biomass gasification at the state of refractory lining the fixed bed reactor

The article deals with the influence of biomass gasification on the condition of the refractory lining of a fixed bed reactor. The refractory lining of the gasifier is one part of the device, which significantly affects the operational reliability and durability. After removing the refractory lining of the gasifier from the experimental reactor, there was done an assessment how gasification of different kinds of biomass reflected on its condition in terms of the main factors affecting its life. Gasification of biomass is reflected on the lining, especially through sticking at the bottom of the reactor. Measures for prolonging the life of lining consist in the reduction of temperature in the reactor, in this case, in order to avoid ash fusion biomass which it is difficult for this type of gasifier.

09 BIOMASS FUELS↗

Leveling Intermittent Renewable Energy Production Through Biomass Gasification-Based Hybrid Systems

The increased use of intermittent renewable power in the United States is forcing utilities to manage increasingly complex supply and demand interactions. This paper evaluates biomass pathways for hydrogen production and how they can be integrated with renewable resources to improve the efficiency, reliability, dispatchability, and cost of other renewable technologies. Two hybrid concepts were analyzed that involve co-production of gaseous hydrogen and electric power from thermochemical biorefineries. Both of the concepts analyzed share the basic idea of combining intermittent wind-generated electricity with a biomass gasification plant. The systems were studied in detail for process feasibility and economic performance. The best performing system was estimated to produce hydrogen at a cost of $1.67/kg. The proposed hybrid systems seek to either fill energy shortfalls by supplying hydrogen to a peaking natural gas turbine or to absorb excess renewable power during low-demand hours. Direct leveling of intermittent renewable electricity production is accomplished with either an indirectly heated biomass gasifier, or a directly heated biomass gasifier. The indirect gasification concepts studied were found to be cost competitive in cases where value is placed on controlling carbon emissions. A carbon tax in the range of $26-40 per metric ton of CO{sub 2} equivalent (CO{sub 2}e) emission makes the systems studied cost competitive with steam methane reforming (SMR) to produce hydrogen. However, some additional value must be placed on energy peaking or sinking for these plants to be economically viable. The direct gasification concept studied replaces the air separation unit (ASU) with an electrolyzer bank and is unlikely to be cost competitive in the near future. High electrolyzer costs and wind power requirements make the hybridization difficult to justify economically without downsizing the system. Based on a direct replacement of the ASU with electrolyzers, hydrogen can be produced for $0.27 premium per kilogram. Additionally, if a non-renewable, grid-mix electricity is used, the hybrid system is found to be a net CO{sub 2}e emitter.

08 HYDROGEN↗

Power Systems Development Facility Gasification Test Campaign TC25

In support of technology development to utilize coal for efficient, affordable, and environmentally clean power generation, the Power Systems Development Facility (PSDF), located in Wilsonville, Alabama, routinely demonstrates gasification technologies using various types of coals. The PSDF is an engineering scale demonstration of key features of advanced coal-fired power systems, including a KBR Transport Gasifier, a hot gas particulate control device, advanced syngas cleanup systems, and high-pressure solids handling systems. This report summarizes the results of TC25, the second test campaign using a high moisture lignite coal from the Red Hills mine in Mississippi as the feedstock in the modified Transport Gasifier configuration. TC25 was conducted from July 4, 2008, through August 12, 2008. During TC25, the PSDF gasification process operated for 742 hours in air-blown gasification mode. Operation with the Mississippi lignite was significantly improved in TC25 compared to the previous test (TC22) with this fuel due to the addition of a fluid bed coal dryer. The new dryer was installed to dry coals with very high moisture contents for reliable coal feeding. The TC25 test campaign demonstrated steady operation with high carbon conversion and optimized performance of the coal handling and gasifier systems. Operation during TC25 provided the opportunity for further testing of instrumentation enhancements, hot gas filter materials, and advanced syngas cleanup technologies. The PSDF site was also made available for testing of the National Energy Technology Laboratory's fuel cell module and Media Process Technology's hydrogen selective membrane with syngas from the Transport Gasifier.

01 COAL, LIGNITE, AND PEAT↗

Assessment of the SRI Gasification Process for Syngas Generation with HTGR Integration – White Paper

This white paper is intended to compare the technical and economic feasibility of syngas generation using the SRI gasification process coupled to several high-temperature gas-cooled reactors (HTGRs) with more traditional HTGR-integrated syngas generation techniques, including: • Gasification with high-temperature steam electrolysis (HTSE), • Steam methane reforming (SMR), and • Gasification with SMR with and without CO 2 sequestration.

03 NATURAL GAS↗

Biomass Gasification Technology Assessment: Consolidated Report

Harris Group Inc. (HGI) was commissioned by the National Renewable Energy Laboratory to assess gasification and tar reforming technologies. Specifically, the assessments focused on gasification and tar reforming technologies that are capable of producing a syngas suitable for further treatment and conversion to liquid fuels. HGI gathered sufficient information to analyze three gasification and tar reforming systems. This report summarizes the equipment, general arrangement of the equipment, operating characteristics, and operating severity for each technology. The order of magnitude capital cost estimates are supported by a basis-of-estimate write-up, which is also included in this report. The report also includes Microsoft Excel workbook models, which can be used to design and price the systems. The models can be used to analyze various operating capacities and pressures. Each model produces a material balance, equipment list, capital cost estimate, equipment drawings and preliminary general arrangement drawings. Example outputs of each model are included in the Appendices.

09 BIOMASS FUELS↗

Alstom’s Limestone Chemical Looping Gasification Process for High Hydrogen Syngas Generation

Alstom Power Inc., a wholly owned subsidiary of the General Electric Company (GE), is developing Limestone-based Chemical Looping (LCL™) Processes, utilizing limestone derived calcium sulfate as an oxygen carrier to transport oxygen from air to the fuel. The LCL™ process is a breakthrough technology with the potential to capture CO 2 and SO 2 from new and existing coal-fired power plants at reduced costs while maintaining high plant power generation efficiency. Chemical looping is a next generation advancement to oxy-combustion which would not require the significant investment in a cryogenic distillation type oxygen production plant. Instead of the energy-consuming oxygen plant, chemical looping uses a benign material to directly remove oxygen from the air and bring that oxygen into contact with the fuel. This "game changing" technology is the lowest cost-of-electricity technical approach that GE Power has identified to date for coal power with carbon capture. The technology has significantly lower capital costs compared to a conventional steam power plant with first generation carbon capture technologies. This new power plant concept is based on a hybrid combustion-gasification process utilizing high temperature chemical and thermal looping technology. In the air reactor, a solid oxygen carrier picks up oxygen from air through an oxidation reaction and leaves nitrogen behind. The hot oxygen-carrying solid carrier is then transported to a fuel reactor, where it releases oxygen. The released oxygen then converts the coal in the fuel reactor into combustion gases. The solid carrier is recycled back to the air reactor for regeneration completing the “chemical loop.” The regeneration step produces heat from which steam is produced for power generation while the process results in a concentrated carbon dioxide stream in which the carbon is captured for use or sequestration (CCUS). Limestone as a precursor for the oxygen carrier is abundant, benign, low cost, and is used in CFB and PC boilers for sulfur control. Challenges associated with this carrier include a complex reaction mechanism with possible side reactions leading to the release of SO 2 . The development of the Limestone Chemical Looping Gasification (LCL-G™) technology was co-funded by the Department of Energy under the DOE/NETL Cooperative Agreement No. DE- FE0023497, in parallel with the collaborative combustion (LCL-C™) program. In this report, the LCL-G™ experimental testing from the electrically-heated, once-through, 100 kW Pilot-Scale Test Facility (PSTF) is analysed and reviewed. The PSTF Oxidizer is a 50-foot tall, 100-mm diameter transport reactor, while the PSTF Reducer reactor is based upon a bubbling-bed design. The experimental data from four (4) test campaigns (denoted “Weeks”) are reviewed and discussed. The LCL-G™ (DE-FE0023497) project objectives for gasification are >90% carbon gasified in the Reducer and a H 2 :CO molar generation ratio of 2:1. These project performance metrics were not met by a single coal test, but they were individually approached in two separate tests.

01 COAL, LIGNITE, AND PEAT↗

Novel Low-Cost Process for the Gasification of Biomass and Low-Rank Coals

Farm Energy envisaged a phased demonstration program, in which a pilot-scale straw gasifier will be installed on a farm. The synthesis gas product will be used to initially (i) generate electricity in a 300 kW diesel generator, and subsequently (ii) used as a feedstock to produce ethanol or mixed alcohols. They were seeking straw gasification and alcohol synthesis technologies that may be implemented on farm-scale. The consortium, along with the USDA ARS station in Corvallis, OR, expressed interest in the dual-bed gasification concept promoted by WRI and Taylor Energy, LLC. This process operated at atmospheric pressure and employed a solids-circulation type oxidation/reduction cycle significantly different from traditional fluidized-bed or up-draft type gasification reactors. The objectives of this project were to perform bench-scale testing to determine technical feasibility of gasifier concept, to characterize the syngas product, and to determine the optimal operating conditions and configuration. We used the bench-scale test data to complete a preliminary design and cost estimate for a 1-2 ton per hour pilot-scale unit that is also appropriate for on-farm scale applications. The gasifier configuration with the 0.375-inch stainless steel balls recirculating media worked consistently and for periods up to six hours of grass feed. The other principle systems like the boiler, the air pump, and feeder device also worked consistently during all feeding operations. Minor hiccups during operation tended to come from secondary systems like the flare or flammable material buildup in the exit piping. Although we did not complete the extended hour tests to 24 or 48 hours due to time and budget constraints, we developed the confidence that the gasifier in its current configuration could handle those tests. At the modest temperatures we operated the gasifier, slagging was not a problem. The solid wastes were dry and low density. The majority of the fixed carbon from the grass ended up in the solid waste collected in the external cyclone. The volatiles were almost all removed in the gasifier. While the average gas heating value of the collected gas products was 50 BTUs/scf or less, addition a of the second gas exit for combustion gases would increase that value by a factor of two or three. Other changes to the current design such as shortening the gasifier body and draft tube would lead to lower air use and shorter heating times. There was no evidence of steam reforming at the current operating temperature. Likewise there was no indication of significant tar production. Reconfiguration of the gasifier at the on farm site may yet yield more significant results that would better qualify this gasifier for small scale biomass operations.

09 BIOMASS FUELS↗

Utilization of solid wastes from the gasification of coal-water slurries

It was found that only fly and bottom ashes are the solid wastes of water-coal slurry gasification in a direct-flow gasifier. The yields and chemical compositions of fly and bottom ashes obtained after the gasification of water-coal slurries prepared using brown (B) and long-flame (D) coals from the Berezovskii and Mokhovskii strip mines (Kansk-Achinsk and Kuznetsk Basins, respectively) were characterized. Based on an analysis of currently available information, the areas of utilization of fly and bottom ashes after water-coal slurry gasification with dry ash removal were summarized. The use of these wastes in the construction of high-ways and earthwork structures (for the parent coals of B and D grades) and in the manufacture of ash concrete (for the parent coal of D grade) is most promising.

01 COAL, LIGNITE, AND PEAT↗

Evaluation of syngas production unit cost of bio-gasification facility using regression analysis techniques

Evaluation of economic feasibility of a bio-gasification facility needs understanding of its unit cost under different production capacities. The objective of this study was to evaluate the unit cost of syngas production at capacities from 60 through 1800Nm 3/h using an economic model with three regression analysis techniques (simple regression, reciprocal regression, and log-log regression). The preliminary result of this study showed that reciprocal regression analysis technique had the best fit curve between per unit cost and production capacity, with sum of error squares (SES) lower than 0.001 and coefficient of determination of (R 2) 0.996. The regression analysis techniques determined the minimum unit cost of syngas production for micro-scale bio-gasification facilities of $0.052/Nm 3, under the capacity of 2,880 Nm 3/h. The results of this study suggest that to reduce cost, facilities should run at a high production capacity. In addition, the contribution of this technique could be the new categorical criterion to evaluate micro-scale bio-gasification facility from the perspective of economic analysis.

Bio-gasification↗

chapter 40 - Gasification Technologies, "Handbook of Climate Change Mitigation and Adaptation"

Gasification is an enabling technology for the clean-up of fossil and biomass fuels for energy production. A history of gasifier development is told from the perspective of a technology evolving to meet the ever changing market needs. The chemistry and physics of coal conversion includes pyrolysis, combustion, gasification, mineral transformations as well as a discussion of the materials developed to meet the most challenging gasifier applications. Integrated gasification and combined cycle processes are discussed with respect to electrical power production. The distinguishing features for different types of gasifiers are described including fixed bed, fluidized bed, entrained flow, transport gasifiers. The twelve major gasifiers being marketed today are described. The hydrodynamics and kinetics of each are reviewed along with salient differences in performance, such as gas composition, when using a variety of fuels under different conditions. Critical operational features that are discussed include oxidizing media, air or oxygen blown; the system pressure; fuel feed stock; and downstream clean-up. Thermal integration is discussed with respect to its impact on the gasifier performance. Gas clean-up is also considered with respect to the removal of potential pollutants and the shifting to environmentally benign transportation and process fuels.

01 COAL, LIGNITE, AND PEAT↗

Rapid gasification of nascent char in steam atmosphere during the pyrolysis of Na- and Ca-ion-exchanged brown coals in a drop-tube reactor

Several recent studies on in situ steam gasification of coal suggest a possibility of extremely fast steam gasification of char from rapid pyrolysis of pulverized brown coal. The unprecedented rate of char steam gasification can be achieved by exposing nascent char, that is, after tar evolution (temperature range >600{sup o}C), but before devolatilization (<900{sup o}C), to steam in the presence of Na and/or Ca dispersed in/on the char. In this study, we conducted rapid pyrolysis experiments using ion-exchanged Loy Yang brown coal samples, that is, H-form coal with Na/Ca contents <0.001 wt %, Na-form coal with Na content = 2.8 wt % and Ca-form coal with Ca content = 3.2 wt %. These samples were pyrolyzed in an atmospheric drop-tube reactor at a temperature of 900{sup o}C, inlet steam concentration of 50 vol. %, and a particle residence times of 2.8 s. The char yields from the pyrolysis of Na-form and Ca-form coals were as low as 12 and 33% on the respective coal carbon bases, and accounted for only 18 and 53% of the char yields from the full devolatilization of the respective coals at 900{sup o}C. In addition, the pyrolysis also consumed as much as 0.7-1.1 mol of H{sub 2}O per mol of coal C. On the other hand, the nascent char from the H-form coal allowed carbon deposition from the nascent tar, resulting in a char yield as high as 115% of that from the full devolatilization. The chars from the Na-form and Ca-form coals also acted as catalysts for steam reforming of tar, which was evidenced by significant negative synergistic effects of blending of H-form coal with Na-form coal or Ca-form coal on the tar and soot yields. 57 refs., 6 figs.

01 COAL, LIGNITE, AND PEAT↗

Comparison of gasification kinetics parameters of different types of nuclear graphite

A chemical-reaction kinetics model of nuclear graphite gasification has recently been developed and successfully validated with gasification rate measurements for nuclear graphite grades of IG-110, IG-430, NBG-18 and NBG-25. The model employs 4 elementary chemical reactions with applicable parameters, including the values and Gaussian-like distributions of the specific activation energies, the pre-exponential coefficients for adsorption of oxygen and desorption of CO and CO{sub 2} gases, and the surface area of free active sites. These parameters are determined from the reported measurements of the total gasification and transient weight loss using a multi-parameter optimization algorithm. The determined chemical kinetics parameters for IG-100 and NB-25 are nearly the same, but slightly different from those for NBG-18 and IG-430. The initial specific area of free active sites is inversely proportional to the square root of the mass or volume of the graphite specimens used in experiments. The recommended chemical kinetics parameters in this paper for these grades of nuclear graphite should be applicable to future safety analysis of high-temperature gas cooled reactors in the unlikely event of a massive air ingress accident. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Diffusion velocity correlation for nuclear graphite gasification at high temperature and low Reynolds numbers

The safety analysis of High-Temperature and Very High Temperature gas-cooled Reactors requires reliable estimates of nuclear graphite gasification as a function of temperature, among other parameters, in the unlikely event of an air ingress accident. Although the rates of the prevailing chemical reactions increase exponentially with temperature, graphite gasification at high temperatures is limited by the oxygen diffusion through the boundary layer. The effective diffusion velocity depends on the total flow rate and pressure of the bulk air-gas mixture. This paper develops a semi-empirical Sherwood number correlation for calculating the oxygen diffusion velocity. The correlation is based on a compiled database of the results of convective heat transfer experiments with wires and cylinders of different diameters in air, water and paraffin oil at 0.006 {<=} Re {<=} 1,604 and 0.068 {<=} Sc {<=} 35.2, and of mass transfer experiments at 4.8 {<=} Re {<=} 77 and 1,300 {<=} Sc {<=} 2,000. The developed correlation is within {+-} 8% of the compiled database of 567 data points and consistent with reported gasification rate measurements at higher temperatures in experiments using different size specimens of nuclear graphite grades of NBG-18 and NB-25, IG-11, IG-110 and IG-430 in atmospheric air at 0.08 {<=} Re {<=} 30. Unlike the Graetz solution that gives a constant Sh of 3.66 at Re {<=} 1.0, the present correlation shows Sh decreases monotonically to much lower values with decreasing Re. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Modeling biomass gasification system using multistep kinetics under various oxygen–steam conditions

Biomass gasification is an effective method to convert low‐value lingocellulosic biomass into useful gas products. The ability to predict the gas composition is important to process design. In this study, simulations of biomass gasification were carried out for various feedstocks at different operating conditions, and the model results were validated using experimental data. A multistep kinetics model was developed to predict the syngas composition using different biomass feedstocks under various oxygen‐enriched air and steam conditions. The oxygen level in the gasifying agent ranged from 21% (air) to 45% (pure oxygen). Five different biomass materials were used, including pine, maple–oak mixture, seed corn, corn stover, and switchgrass. The fluidized bed gasifier was maintained at 800°C. The present kinetics model was able to predict the concentrations of H 2 , CO, CO 2 , H 2 O, CH 4 , and N 2 in the syngas, and the predicted compositions were in good agreement with the experimental data. The results show that the model was sensitive to the variation in the oxygen level, steam flow rate, and the composition of the biomass material. As the oxygen level increased, the model also predicted the increase in H 2 , CO, CH 4 , and the H 2 /CO ratio. The mechanism on improving the syngas quality was also explained by analyzing the reaction equations. The increase in hydrogen is believed to be due to the use of steam for gasification. The present model can further be integrated into the process simulation model for predicting the performance of a biorefinery to help utilize biomass energy. © 2015 American Institute of Chemical Engineers Environ Prog, 34: 1148–1155, 2015

Banerjee, Sudhanya↗