Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FISSION GAS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Polypole Program For The Calculation Of Intra-granular Fission Gas Release

PolyPole is a numerical algorithm for the calculation of intra-granular fission gas release. In particular, the algorithm solves the gas diffusion problem in a fuel grain in time-varying conditions. The program has been extensively tested. PolyPole combines a high accuracy with a high computational efficiency and is ideally suited for application in fuel performance codes.

Pastore, Giovanni↗

Increasing of MERARG experimental performances: on-line fission gas release measurement by mass spectrometry

The MERARG device - implemented at the LECASTAR Hot Laboratory, at the CEA Cadarache - allows characterizing nuclear fuels with respect to the behaviour of fission gases during thermal transients representative of normal or off normal operating nuclear power plant conditions. The fuel is heated in order to extract a part or the total gas inventory it contains. Fission Gas Release (FGR) is actually recorded by mean of both on-line gamma spectrometry station and micro gas chromatography. These two devices monitor the quantity and kinetics of fission gas release rate. They only address {sup 85}Kr radioactive isotope and the elemental quantification of Kr, Xe and He (with a relatively low detection limit in the latter case, typically 5-10 ppm). In order to better estimate the basic mechanisms that promote fission gas release from irradiated nuclear fuels, the CEA fuel study department decided to improve its experimental facility by modifying MERARG to extend the studies of gamma emitter fission gases to all gases (including Helium) with a complete isotopic distribution capability. To match these specifications, a Residual Gas Analyser (RGA) has been chosen as mass spectrometer. This paper presents a review of the main aspects of the qualification/calibration phase of the RGA type analyser. In particular, results recorded over three mass ranges 1-10 u, 80-90 u and 120-140 u in the two classical modes of MERARG, i.e. on-line and off-line measurements are discussed. Results obtained from a standard gas bottle show that the quantitative analysis at a few ppm levels can be achieved for all isotopes of Kr and Xe, as well as masses 2 and 4 u. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of an In Situ Fission Gas Release Instrument for Fuel Sample Irradiations in the High Flux Isotope Reactor

Experimental measurement of gaseous fission product release with respect to temperature and burnup is a critical aspect of understanding nuclear fuel performance, validating predictive models, and qualifying new fuels. To measure this phenomenon in real-time, Oak Ridge National Laboratory has developed an instrument for measuring in situ fission gas release from small-scale fuel samples irradiated in the High Flux Isotope Reactor (HFIR). The instrument uses a continuous flow of Heover the fuel samples to sweep gaseous fission products from a sealed capsule in the HFIR Be reflector to an instrument station adjacent to the reactor. The instrument station houses two high-purity germanium (HPGe) detectors that measure decay gamma rays from fission products passing through a room temperature dwell chamber placed over the detector crystal. The sealed capsules in the reactor are designed to modulate fuel sample temperatures between 700 and 1,100°C by changing the Ar/He gas mixture surrounding the capsules during irradiation. N-type thermocouples are incorporated into the capsule housing to record real-time fuel temperatures. The capsules are heated primarily by prompt gamma rays emitted from the HFIR core with minimal heat contributions from fission in the fuel samples to minimize temperature gradients in the specimens for separate-effects characterization of the material. This paper describes modeling of time-dependent nuclear heating and fission product formation in fuel samples, thermal characteristics of the in-core capsules, and expected gaseous fission product gamma spectra at the HPGe instrument station.

Mulligan, Padhraic L [ORNL] (ORCID:000000025826540↗

Evaluating transient fission gas release in high burnup light water reactor fuel during loss of coolant accident conditions via new capabilities

In this work, the role of transient fission gas release (tFGR) in the cladding burst behavior of high burnup fuel during a loss-of-coolant accident (LOCA) in commercial light water reactors was further investigated via the use of a new apparatus. During the LOCA-related temperature ramps of high burnup fuel, the release of fission gases exceeds the steady-state release observed under normal operating conditions. An enhancement was made to the Oak Ridge National Laboratory Severe Accident Test Station (SATS) to probe the various factors influencing tFGR. Experiments were performed on commercially irradiated, zirconium-clad uranium dioxide fuel, and this paper details the design of the experimental setup, the initial test results, and the subsequent post-test analyses. Notably, the first test on high burnup fuel demonstrated a LOCA-relevant tFGR of 5.3% from an unpressurized fuel segment. The ultimate tFGR was 10.7% for beyond LOCA conditions. A follow-up test on similar fuel revealed a tFGR of 12.6% under comparable conditions. Microstructural analysis and an analysis of the released gas provide some insight regarding the source of tFGR in the fuel. Finally, a grain boundary bubble model may aid in the interpretation of the results and offer a guide for future work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Phase-field simulations of fission gas bubble growth and interconnection in U-(Pu)-Zr nuclear fuel

Abstract The growth and interconnection of fission gas bubbles in the hotter central regions of U-(Pu)-Zr nuclear fuel has been simulated with a phase-field model. The Cahn-Hilliard equation was used to represent the two-phase microstructure, with a single defect species. The volume fraction of the bubble phase and surface area of the bubble-matrix interface were determined during growth and interconnection. Surface area increased rapidly during the initial stages of growth, then slowed and finally decreased as bubble interconnection began and coarsening acted to reduce surface area. The fraction of the bubbles vented to a simulation domain boundary, f V , was quantified as a measure of the microstructure’s interconnectivity and plotted as a function of porosity p . The defect species diffusivity was varied; although changes in diffusivity significantly affected the microstructure, the plots of f V vs. p did not change significantly. The percolation threshold p c was calculated to be approximately 0.26, depending on the assumed diffusivity and using an initial bubble number density based on experimental observations. This is slightly smaller than the percolation threshold for continuum percolation of overlapping 3D spheres. The simulation results were used to parameterize two different engineering-scale swelling models for U-(Pu)-Zr in the nuclear fuel performance code BISON.

Aagesen, Larry K. (ORCID:000000034936676X)↗

Swelling and Fission Gas Release of U-10Mo and U-17Mo Following Neutron Irradiation at 250 – 500°C

The performance of metallic fuel alloys, U-10Mo and U-17Mo, was examined using the MiniFuel test system in the High Flux Isotope Reactor. Approximately 0.8 mm thick disks were irradiated at target temperatures of 250°C, 350°C, 450°C, and 500°C up to three different fission densities, culminating at a maximum fission density of 6.8 × 10 20 cm −3 . Fission rates decayed from 3 – 6 × 10 13 cm −3 s −1 to 2 – 4 × 10 13 cm −3 s −1 over the course of the longest, eight cycle, irradiation as the 235 U was consumed and the 239 Pu concentration accumulated. Actual irradiation temperature on the last day of irradiation was measured via dilatometry using the SiC passive thermometry recovered from the MiniFuel subcapsules and compared favorably with the thermal calculations using as-built geometry and test conditions. Furthermore, average simulated temperatures were within 50°C of the target temperatures, except for the 500°C irradiation, for which the temperature variation was 62°C, 32°C, and 90°C in the in two, four, and eight cycle irradiations, respectively. Fission gas release (FGR) measurements showed no release above recoil for any U-17Mo fuels or for the U-10Mo fuel irradiated at 250°C. Finally, significant (40%–80%) FGR was found for the medium- to highest-burnup U-10Mo samples irradiated at target temperatures 350°C–500°C. Significant FGR correlated with sample thickness swelling, which was as high as 13%–35% for high-release samples and below 7% for all other (low–gas release) samples.

FGR↗

Effects of transient fission gas release on rod balloon burst behavior during a loss-of-coolant accident

The US nuclear energy industry is investigating strategies to increase the reactor operating cycle to 24 months, which would result in rod average burnups exceeding the current limit of 62 GWd/tU. To support this goal, multiphysics simulations tools and methodologies are being developed to predict the effects of this change during transient events such as loss-of-coolant accidents (LOCAs). In this work, two cladding burst correlations were used to predict cladding failure. Here, these were coupled with three transient fission gas release (tFGR) models and were implemented in the BISON fuel performance code to quantify any changes in cladding burst behavior during a large-break LOCA. First, a simple linear model was used to perform a sensitivity analysis of a single fuel rod. Second, a tFGR model available in BISON was applied to 281 fuel rods throughout the core. The third model examined was an empirical correlation based on data from the literature.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

An innovative acoustic sensor for first in-pile fission gas release determination - REMORA 3 experiment

A fuel rod has been instrumented with a new design of an acoustic resonator used to measure in a non destructive way the internal rod plenum gas mixture composition. This ultrasonic sensor has demonstrated its ability to operate in pile during REMORA 3 irradiation experiment carried out in the OSIRIS Material Testing Reactor (CEA Saclay, France). Due to very severe experimental conditions such as temperature rising up to 150 deg.C and especially, high thermal fluence level up to 3.5 10{sup 19} n.cm{sup 2}, the initial sensor gas speed of sound efficiency measurement was strongly reduced due to the irradiation effects on the piezo-ceramic properties. Nevertheless, by adding a differential signal processing method to the initial data analysis procedure validated before irradiation, the gas resonance peaks were successfully extracted from the output signal. From these data, the molar fractions variations of helium and fission gas were measured from an adapted Virial state equation. Thus, with this sensor, the kinetics of gas release inside fuel rods could be deduced from the in-pile measurements and specific calculations. These data will also give information about nuclear reaction effect on piezo-ceramics sensor under high neutron and gamma flux. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

FEMAXI-V benchmarking study on peak temperature and fission gas release prediction of PWR rod fuel

The present paper reports a study of FEMAXI-V code and related report on code benchmarking. Capabilities of the FEMAXI-V code to predict the thermal and fission gas release have been tested on MOX fuels in LWRs which has been done in SCK{center_dot}CEN and Belgonucleaire by using PRIMO MOX rod BD8 irradiation experiment after V Sobolev as reported O. J. Ott. Base irradiation in the BR3 reactor, the BD8 rod was transported to CEA-Saclay for irradiation in the OSIRIS reactor (ramp power excursion). The irradiation device used for the PRIMO ramps was the ISABELLE 1 loop, installed on a movable structure of the core periphery. The power variations were obtained by inwards/backwards movements of the loop in the core water. The preconditioning phase for rod BD8 occurred at a peak power level of 189 W/cm with a hold time of 27 hours. The subsequent power excursion rate amounted to 77 W/ (cm.min), reaching a terminal peak power level of 395 W/cm that lasted for 20 hours.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Extension of Clad Damage Propagation Model for Fission Gas Dispersal and Two-Phase Flow Effects in MOOSE SubChannel Module

This report presents an extension of the Clad Damage Propagation (CDAP) model implemented in the MOOSE SubChannel Module (SCM) to capture post-failure fission-gas dispersal and two-phase flow effects in sodium-cooled fast reactor assemblies. The extended model tracks discharged gas axially and radially, computes channel-averaged flow quality and void fraction using a Lockhart–Martinelli framework, evaluates two-phase frictional pressure-drop multipliers, determines inlet mass-flow degradation under fixed core pressures, and applies an intensified-void-based heat-transfer degradation to affected fuel pins. Radial plume expansion is parameterized using mineral-oil jet experiments mapped to sodium conditions via Reynolds–Weber similarity. Implementation details are documented, along with the new methods and user inputs needed to control plume mapping and two-phase behavior. Demonstration simulations for 19- and 37-pin bundles show that breach size and inlet velocity strongly influence propagation potential: small breaches (≤0.5 mm) produce limited degradation while larger breaches (~1 mm) can drive oscillatory temperature spikes and enhanced failure propagation, especially at higher velocities. These results demonstrate that the extended CDAP model provides a more complete framework for quantifying cladding damage propagation and evaluating propagation potential in transient scenarios. The approach remains computationally efficient, consistent with subchannel-level analysis, yet incorporates sufficient physics to bridge localized post-failure effects with bundle- and assembly-scale degradation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Kriging-Based Inverse Uncertainty Quantification of BISON Fission Gas Release Model

Nuclear reactor fuel performance analysis studies the thermo-mechanical behavior of fuel rods and verify their compliance with safety criteria under both normal operation and accidental conditions. One of the major concerns in fuel performance analysis is the behavior of the fission gases xenon and krypton in uranium dioxide fuel, which significantly affect the thermo-mechanical performance of the nuclear fuel rods employed in current LWRs. Previously, the modeling of fission gas release (FGR) in nuclear fuel performance codes have been relying on empirical models which are not applicable beyond their range of calibration. Recently a more efficient and flexible physics-based FGR and swelling model that can describe a wider range of reactor operation conditions have been implemented in fuel performance code BISON. In this work, we performed Bayesian calibration to inversely quantify the uncertainties associated with the 5 tuning parameters in BISON FGR model, based on the time-dependent FGR measurement data from Riso-AN3 benchmark. It takes around 1 hour and 40 minutes for BISON to simulate the Riso-AN3 benchmark with a moderate mesh size using 32 processors. As hundreds of thousands of BISON simulations are needed during Markov Chain Monte Carlo (MCMC) sampling, running BISON directly is not a viable solution. Therefore we propose to use Kriging-based metamodels to replace BISON during MCMC sampling. Surrogate model is an approximation of the input/output relation of a computer code/model. It is also called metamodel, response surface, emulator. Surrogate models usually take much less computational time than the original model (like BISON) while maintaining the input/output relation of the original model to a desirable accuracy. Constructing the metamodels normally requires small number of executions of the original model. Once validated, metamodels can be used to perform uncertainty and sensitivity analysis, Bayesian calibration, optimization, etc.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Early self-organization of fission gas bubble superlattice formation in neutron-irradiated monolithic U-10Mo fuels

Self-organization of defect superlattices in far-from-equilibrium systems presents a promising way to mitigate swelling concerns in nuclear materials. The gas bubble superlattice (GBS) is a highly ordered, three-dimensional complex defect structure that can retain fission gasses in Uranium-Molybdenum (U-Mo) fuels. Transmission electron microscopy (TEM) investigation of monolithic U-10Mo fuel irradiated to 1.15 × 10 21 fissions/cm 3 and 1.30 × 10 21 fissions/cm 3 revealed that early-stage ordering preferentially occurs at the grain boundaries (GB) and that the critical bubble size for complete ordering is ~3 nm. Once formed at the GB, the GBS extends towards the grain interior; however, the spread in distance from the GB varies likely depending on the type and strength of the GB sink. TEM results also showed a possible correlation between the growth and evolution of the intragranular disordered bubbles and large dislocation networks. The fission product distribution in and outside of the GBS was also investigated confirming the presence of xenon in the GBS, as well as other fission products including cesium, barium, lanthanum, and cerium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Empirical and mechanistic transient fission gas release model for high-burnup LOCA conditions

In response to the nuclear industry desire to extend burnup beyond current licensing practices, the US Nuclear Regulatory Commission (NRC) released a research information letter (RIL) that provides a basis for analyzing fuel fragmentation, relocation, and dispersal (FFRD) in light-water reactors. Of the five elements discussed, the most ambiguous is the significance of transient fission gas (FG) release (FGR) (tFGR) and its effects on fuel performance under loss-of-coolant accident conditions. In fresh fuel, FG migration and eventual release is primarily governed by diffusion-based mechanisms at higher temperatures (>1,000 °C). However, the mechanisms governing FGR changes as burnup increases. More recent research indicates that FGR increases as burnup increases, specifically under temperature transient conditions, and this release occurs at lower temperatures with a new release mechanism. This behavior has been attributed to microcracking in the fuel and is likely related to microstructure embrittlement with the presence of over pressurized FG bubbles. The NRC RIL outlines the complexity of the phenomenon and a need for a deeper understanding to adequately address FFRD for regulatory application. Here, therefore, this manuscript intends to summarize the publicly available tFGR data and discuss the observed dependencies (e.g., burnup, heating rate, sample geometry, terminal temperature). An empirical model has been developed and benchmarked against recently published experimental data. However, this empirical model is limited to conditions for which fitting data exist and, therefore, a high-level discussion is included to provide a roadmap for atomistically-informed multiscale modeling in conjunction with experimental data collection to develop a mechanistic tFGR model widely applicable to a broad range of nuclear fuel conditions at high burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Density functional theory calculations of defect and fission gas properties in U-Si fuels

Accident tolerant fuels (ATF) are being developed in response to the Fukushima Daiichi accident in Japan. One of the options being pursued is U-Si fuels, such as the U 3 Si 2 and U 3 Si 5 compounds, which benefit from high thermal conductivity (metallic) compared to the UO 2 fuel (insulator or semi-conductor) used in current Light Water Reactors (LWRs). The U-Si fuels also have higher fissile density. In order to perform meaningful engineering scale nuclear fuel performance simulations, the material properties of the fuel, including the response to irradiation environments, must be known. Unfortunately, the data available for U-Si fuels are rather limited, in particular for the temperature range where LWRs would operate. The ATF HIP is using multi-scale modeling and simulations to address this knowledge gap. The present study investigates point defect and fission gas properties in U 3 Si 2 , which is one of the main fuel candidates, using density functional theory (DFT) calculations. Based on a few assumption regarding entropy contributions, defect and fission diffusivities are predicted. Even though uranium silicides have been shown to amorphize easily at low temperature, we assume that U 3 Si 2 remains crystalline under the conditions expected in Light Water Reactors (LWRs). The temperature and dose where amorphization occurs has not yet been well established.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Sister Rod Destructive Examinations (FY23) Appendix D: Fission Gas, Fuel Burnup, and Fuel Isotopic Measurements

As a part of DOE NE High Burnup Spent Fuel Data Project, Oak Ridge National Laboratory (ORNL) is performing destructive examinations (DEs) of high burnup (HBU) (>45 GWd/MTU) spent nuclear fuel (SNF) rods from the North Anna Nuclear Power Station operated by Dominion Energy. The SNF rods, called sister rods or sibling rods, are all HBU and include four different kinds of fuel rod cladding: standard Zircaloy-4 (Zirc-4), low-tin (LT) Zirc-4, ZIRLO, and M5. The DEs are being conducted to obtain a baseline of the HBU rod’s condition before dry storage and are focused on understanding overall SNF rod strength and durability. Composite fuel and defueled cladding will be tested to derive material properties. Although the data generated can be used for multiple purposes, one primary goal for obtaining the post-irradiation examination data and the associated measured mechanical properties is to support SNF dry storage licensing and relicensing activities by (1) addressing identified knowledge gaps and (2) enhancing the technical basis for post-storage transportation, handling, and subsequent disposition. This appendix documents the status of the ORNL Phase 1 DE activities related to fission gas sample analysis, fuel burnup analysis, and fuel isotopic analysis of selected sister specimens in Phase 1 of the sister rod test program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fission gas bubbles and recrystallization-induced degradation of the effective thermal conductivity in U-7Mo fuels

We have developed a mesoscale model to calculate the degradation of the effective thermal conductivity in irradiated U-Mo alloys caused by the fission-induced gas bubbles and recrystallization. The phase-field approach is employed to generate the grain microstructures of U-7Mo fuels with intra- and inter-granular gas bubbles. Based on the phase-field microstructures, the thermal conductivities of U-7Mo as a function of the fission density can be predicted by the developed mesoscale model. The predicted values of effective thermal conductivities are consistent with available experimental data. Results show that the effective thermal conductivity decreases rapidly with recrystallization compared to the one prior to recrystallization, which can be attributed to the sudden increase of grain boundary densities and corresponding intergranular gas bubbles at high fission densities. Smaller grain size fuel structure has a lower thermal conductivity at the same fission density due to the increased grain boundary density. The current study can provide a better understanding of the fission-induced degradation mechanism of the thermal conductivity in U-Mo fuels.

36 MATERIALS SCIENCE↗

Fission Gas Measurements in Spent Fuel: Literature Review

The fission-derived noble gases, xenon(Xe) and krypton(Kr), have long been proposed as a tool for supporting nuclear safeguards and declarations verification. A vast body of literature outlines how these non-reactive fission gases released during reactor operation and shutdowns correlate to burnup level, power history, other reactor specifications and reprocessing activities. However, irradiation conditions can vary appreciably both radially and axially within a fuel pin.

07 ISOTOPE AND RADIATION SOURCES↗