Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FILL FACTORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Broad emission lines of QSOs are consistent with rotating supermassive stars

The basic properties of broad emission-line profiles from quasars and Seyfert galaxies are suggested to indicate emissions originating from the surface of a rotating supermassive star. The areal extent of the ionizing luminosity and its energy are calculated, showing that the broad-line region has a mass of about 10 solar masses and a volume filling factor of 1/1,000,000. It is shown that if the broad-line region consists of a layer of ionized gas on the surface of a rotating supermassive star with an equatorial speed of 5,000 km/sec and a relatively cool surface, a layer of photoionized gas will result and emit a line emission per unit area that is proportional to the incident flux of ionizing radiation. The emitting layer will be heated to about 100 million K by an X ray component of a nonthermal continuum over a 10,000 K surface.

Shields, G. A.↗
NASA NTRS1984

Interaction of Convection and Small-scale Magnetic Fields: Influence on the Solar Luminosity

Changes in the local solar luminosity due to the presence of a small scale structured (facular) magnetic field in the photosphere are discussed. The discussion is based on three dimensional numerical simulations of the magnetohydrodynamics of the top of the convection zone, and the adjacent stable photosphere. The simulations demonstrate that practically all of the magnetic flux present is concentrated into intense magnetic flux structures, such that the magnetic field pressure is balanced by the gas pressure of the surrounding plasma. The flux concentration is caused by the convectively unstable stratification. The average luminosity of the area is influenced by three effects: (1) the brightness of the flux concentrations, (2) their filling factor, and (3) the average luminosity of the surrounding plasma.

Nordlund, A.↗
NASA NTRS1984

On-orbit performance of LIPS gallium arsenide solar cell experiment

Telemetry from the Living Plume Shield's gallium arsenide solar panel experiment was evaluated to determine degradation. The data were culled to preclude spurious results from possible shadowing or inaccurate measurements on a cold array. Two independent methods were then used to obtain the maximum power points and the various characteristics of the solar array. Fill factor, open circuit voltage, short circuit current, and series and shunt resistances were examined. The data analysis concluded that, to date, nearly all of the solar array degradation is due to the reduction in the short circuit current.

Bavaro, T.↗
NASA NTRS1982

Towards a 700 mV silicon solar cell

The key to improved silicon solar cell performance lies in increasing cell open circuit voltage. Not only does improved voltage direclty increase cell efficiency, but it also increases the limiting value of fill factor and decreases the temperature sensitivity of the cell. Limits on attainable open circuit voltage are not well defined. A thermodynamic limit of 850 mV exists for black body silicon cells, with 700 mV long regarded as a practical limit. This paper describes experimental work which has resulted in experimental devices with open circuit voltages approaching 700 mV. Values up to 694 (AM0, 25 C) have been demonstrated. The cells are similar in structure to conventional p-n junction cells, but particular attention is paid to passivating the entire top surface of the cell, including regions under the top contact.

Green, M. A.↗
NASA NTRS1984

Broad band X-ray astronomical spectroscopy

The Broad Band X-Ray Telescope (BBXRT) experiment has been designed for high sensitivity, moderate resolution spectrophotometry of cosmic sources in the range 0.5 to 12 keV. Principal elements are two co-aligned imaging telescopes with cooled Si(Li) detectors at each focus. The mirror design uses an approximate geometry of tightly nested, conical, foil reflectors that allow a large filling factor (high throughput) at small grazing angles (high energy response). Each detector consists of a cluster of five elements defined with grooves on a single crystal. This arrangement affords some spatial resolution as well as a means of substantial background reduction. Shuttle borne measurements will typically be of 2000 s duration for sources with a flux of 10 to the -12 erg/sq cm-s.

Serlemitsos, P. J.↗
NASA NTRS1984

Coupling coefficient of gain-guided lasers

An analytical model is presented for the coupling coefficient for two gain-guided coupled waveguides, e.g., semiconductor laser arrays. A common parabolic gain distribution is assumed for the lasers, and the effective dielectric constant distribution is approximated in terms of the bulk refraction index, wavelength, power filling factor, and the antiguiding factor. The fundamental mode is then formulated and used in an integral for the coupling coefficient. The dependence of the coefficient of various waveguide parameters is described.

Katz, J.↗
NASA NTRS1984

18-percent efficient terrestrial silicon solar cells

Silicon solar cells are described which operate at energy conversion efficiencies in excess of 18 percent under standard terrestrial test conditions (AM1.5, 100 mW/sq cm, 28 C). These are believed to be the most efficient silicon cells reported to date. The high efficiency is a result of the combination of high open-circuit voltage due to the careful attention paid to passivation of the top surface of the cell; high fill factors due to the high open-circuit voltage and low parasitic resistance losses; and high short-circuit current due to the use of shallow diffusions, a low grid coverage, and an optimized double-layer antireflection coating.

Blakers, A. W.↗
NASA NTRS1984

Process Research on Polycrystalline Silicon Material (PROPSM)

Results of hydrogen-passivated polycrystalline silicon solar cells are summarized. Very small grain or short minority-carrier diffusion length silicon was used. Hydrogenated solar cells fabricated from this material appear to have effective minority-carrier diffusion lengths that are still not very long, as shown by the open-circuit voltages of passivated cells that are still significantly less than those of single-crystal solar cells. The short-circuit current of solar cells fabricated from large-grain cast polycrystalline silicon is nearly equivalent to that of single-crystal cells, which indicates long bulk minority-carrier diffusion length. However, the open-circuit voltage, which is sensitive to grain boundary recombination, is sometimes 20 to 40 mV less. The goal was to minimize variations in open-circuit voltage and fill-factor caused by defects by passivating these defects using a hydrogenation process. Treatments with molecular hydrogen showed no effect on large-grain cast polycrystaline silicon solar cells.

Culik, J. S.↗
NASA NTRS1985

Processing technology for high efficiency silicon solar cells

Recent advances in silicon solar cell processing have led to attainment of conversion efficiency approaching 20%. The basic cell design is investigated and features of greatest importance to achievement of 20% efficiency are indicated. Experiments to separately optimize high efficiency design features in test structures are discussed. The integration of these features in a high efficiency cell is examined. Ion implantation has been used to achieve optimal concentrations of emitter dopant and junction depth. The optimization reflects the trade-off between high sheet conductivity, necessary for high fill factor, and heavy doping effects, which must be minimized for high open circuit voltage. A second important aspect of the design experiments is the development of a passivation process to minimize front surface recombination velocity. The manner in which a thin SiO2 layer may be used for this purpose is indicated without increasing reflection losses, if the antireflection coating is properly designed. Details are presented of processing intended to reduce recombination at the contact/Si interface. Data on cell performance (including CZ and ribbon) and analysis of loss mechanisms are also presented.

Spitzer, M. B.↗
NASA NTRS1985

The X-ray corona of Procyon

X-ray emission from the nearby system Procyon A/B (F5 IV + DF) was detected, using the IPC (Imaging Proportional Counter) on board the Einstein Observatory. Analysis of the X-ray pulse height spectrum suggests that the observed X-ray emission originates in Procyon A rather than in the white dwarf companion Procyon B, since the derived X-ray temperature, log T = 6.2, agrees well with temperatures found for quiescent solar X-ray emission. Modeling Procyon's corona with loops characterized by some apex temperature Tmax and emission length scale L, it is found that Tmax is well constrained, but L, and consequently the filling factor of the X-ray emitting gas, are essentially unconstrained even when EUV emission from the transition region is included in the analysis.

Schmitt, J. H. M. M.↗
NASA NTRS1984

High-efficiency silicon solar cells

Silicon solar cells are described which operate at energy conversion efficiencies independently measured at 18.7 percent under standard terrestrial test conditions (AM1.5, 100 mW/sq cm, 28 C). These are apparently the most efficient silicon cells fabricated to date. The high-efficiency results from a combination of high open-circuit voltage due to the careful attention paid to the passivation of the top surface of the cell, high fill factor due to the high open-circuit voltage and low parasitic resistance losses, and high short-circuit current density due to the use of shallow diffusions, a low grid coverage, and an optimized double layer antireflection coating.

Green, M. A.↗
NASA NTRS1985

The nondetection of continuum radiation from Comet IRAS-Araki-Alcock (1983d) at 2- to 6-cm wavelengths and its implication on the icy-grain halo theory

The Comet IRAS-Araki-Alcock was observed with the VLA at 6 and 2 cm, when the comet was at geocentric distances of 0.08 and 0.035 AU, respectively, and the results are discussed. The three sigma upper limits to the flux density are 90 and 750 micro-Jy at the two wavelengths, respectively, values fully two orders of magnitude below the flux densities predicted by the icy-grain halo theory as initially developed. The corrected theory also indicates that the icy grain halo theory does not give an adequate description of the cometary environment. It is shown that the halo is either very optically thin, with a filling factor of the order of 10 to the -5th, or that the maximum size of the grain that can be lifted off the nuclear surface is only of the order of 10-100 microns.

De Pater, I.↗
NASA NTRS1985

Photon radiation effects on CdS/CuInSe2 thin film solar cells

The unknown tolerance of CuInSe2 cells to proton irradiation, was tested. It was shown that CdS/CuInSe2 solar cells have an inherent tolerance to irradiation by 1 MeV electrons up to at least 2 x 10 to the 16th power electrons/sq cm. Eleven, unencapsulated, 1 sq cm cells deposited on alumina substrates were irradiated with 1 MeV protons at normal incidence. The cells were exposed to six fluences ranging from 2.5 x 10 to the 10th power protons/sq cm to 5.0 x 10 to the 13th power protons/sq cm. After each interval of exposure, the cells were removed from the radiation chamber to undergo current/voltage characterization. It is shown that none of the cells electrical characteristics exhibited any degradation up to and including a fluence of 1 x 10 to the 11th power protons/sq cm. At fluences greater than this, the damage to the CuInSe2 cells V sub oc and fill factor (FF) was more severe than that exhibited by the Isc. The CuInSe2 cells proved to be approximately a factor of 50 more resistant to 1 MeV proton irradiation than silicon or gallium arsenide cells. Annealing of a CuInSe2 cell at 225 deg C for 6 minutes restored it to within 95% of its initial efficiency.

Dursch, H.↗
NASA NTRS1985

Thermal stress cycling of GaAs solar cells

A thermal cycling experiment was performed on GaAs solar cells to establish the electrical and structural integrity of these cells under the temperature conditions of a simulated low-Earth orbit of 3-year duration. Thirty single junction GaAs cells were obtained and tests were performed to establish the beginning-of-life characteristics of these cells. The tests consisted of cell I-V power output curves, from which were obtained short-circuit current, open circuit voltage, fill factor, and cell efficiency, and optical micrographs, spectral response, and ion microprobe mass analysis (IMMA) depth profiles on both the front surfaces and the front metallic contacts of the cells. Following 5,000 thermal cycles, the performance of the cells was reexamined in addition to any factors which might contribute to performance degradation. It is established that, after 5,000 thermal cycles, the cells retain their power output with no loss of structural integrity or change in physical appearance.

Janousek, B. K.↗
NASA NTRS1985

Environmental tests of metallization systems for terrestrial photovoltaic cells

Seven different solar cell metallization systems were subjected to temperature cycling tests and humidity tests. Temperature cycling excursions were -50 deg C to 150 deg C per cycle. Humidity conditions were 70 deg C at 98% relative humidity. The seven metallization systems were: Ti/Ag, Ti/Pd/Ag, Ti/Pd/Cu, Ni/Cu, Pd/Ni/Solder, Cr/Pd/Ag, and thick film Ag. All metallization systems showed a slight to moderate decrease in cell efficiencies after subjection to 1000 temperature cycles. Six of the seven metallization systems also evidenced slight increases in cell efficiencies after moderate numbers of cycles, generally less than 100 cycles. The copper based systems showed the largest decrease in cell efficiencies after temperature cycling. All metallization systems showed moderate to large decreases in cell efficiencies after 123 days of humidity exposure. The copper based systems again showed the largest decrease in cell efficiencies after humidity exposure. Graphs of the environmental exposures versus cell efficiencies are presented for each metallization system, as well as environmental exposures versus fill factors or series resistance.

Alexander, P., Jr.↗
NASA NTRS1986

Observations of Far-Infrared Molecular Emission Lines from the Orion Molecular Cloud

The Orion Nebula was the subject of intensive study for over one hundred years. Recently, several far infrared transitions among the low-lying levels of OH were observed toward IRc2. The OH is thought to be abundant, and plays an important role in the chemical evolution of shock and post-shock regions. The OH emission serves as a sensitive probe of the temperature and density for the shock-processed gas. A rigorous treatment of the radiative transfer of these measured transitions was performed using the escape probability formalism. From this analysis, the temperature of the OH-emitting region was determined to be on the order of 40K. This suggests that the gas is part of the post-shock gas that has cooled sufficiently, most likely by way of radiative cooling by CO. Such cooling from shock temperatures of several degrees can be accomplished in 100 years. A molecular hydrogen density of 3 million/cubic cm and an OH column density of 1.0 x 10 to the 17th /sq cm is found. The beam filling factor is determined to be 36%.

Viscuso, P. J.↗
NASA NTRS1985

Stellar activity in synchronized binaries. I - Dependence on rotation

A large sample of late-type binaries with orbital periods from 1 to 100 days has been examined for relationships between stellar activity and rotation period (assumed - with a few exceptions - to be synchronized with the stellar orbital period). Most of the systems are in the RS Canum Venaticorum class of close binaries; none are contact binaries. The activity diagnostics were observed with the IUE and the Einstein Observatory and range from the mid-chromosphere to the corona. There is a dependence of activity on rotation in the synchronized binaries; surface flux is the preferable measure of activity and is best when steps are taken to remove variations in activity filling factors.

Basri, G.↗
NASA NTRS1985

Observations of OH and CO in the Orion Molecular Cloud

The results of millimeter and submillimeter observations of the BN-KL region of the Orion molecular cloud are reported. Observations were made with a 91 cm bent Cassegrain telescope fitted with an interferometer/grating spectrometer during flights at 13-14 km altitude in the NASA Kuiper Observatory. The data collected covered the 2Pi(1/2)J = 3/2 yields 1/2 and 2Pi(3/2)J = 7/2 yields 5/2 rotational transitions of OH. The measurements were made at 163 and 84 micron wavelengths, respectively. The OH emitting regions was estimated to have a temperature of 1000 K and a molecular hydrogen density of about 6 million/cu cm. Depopulation of the excited states of OH was caused primarily by collisional excitation. The OH fill factor for the region survey was about 10 percent, in line with predictions for a post-shocked region.

Viscuso, P. J.↗