Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Express Data Production”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Investigation of N2O Production from 266 and 532 nm Laser Flash Photolysis of O3/N2/O2 Mixtures

Tunable diode laser absorption spectroscopy has been employed to measure the amount of N2O produced from laser flash photolysis of O3/N2/O2 mixtures at 266 and 532 nm. In the 532 nm photolysis experiments very little N2O is observed, thus allowing an upper limit yield of 7 x 10(exp -8) to be established for the process O3 + N2 yield N2O + O2, where O3 is nascent O3 that is newly formed via O(3P(sub J)) + O2 recombination (with vibrational excitation near the dissociation energy of O3). The measured upper limit yield is a factor of approx. 600 smaller than a previous literature value and is approximately a factor of 10 below the threshold for atmospheric importance. In the 266 nm photolysis experiments, significant N2O production is observed and the N2O quantum yield is found to increase linearly with pressure over the range 100 - 900 Torr in air bath gas. The source of N2O in the 266 nm photolysis experiments is believed to be the addition reaction O(1D(sub 2)) + N2 + M yields (k(sub sigma)) N2O + M, although reaction of (very short-lived) electronically excited O3 with N2 cannot be ruled out by the available data. Assuming that all observed N2O comes from the O(1D(sub 2)) + N2 + M reaction, the following expression describes the temperature dependence of k(sub sigma) (in its third-order low-pressure limit) that is consistent with the N2O yield data: k(sub sigma) = (2.8 +/- 0.1) x 10(exp -36)(T/300)(sup -(0-88+0.36)) cm(sup 6) molecule(sup -2)/s, where the uncertainties are 2(sigma) and represent precision only. The accuracy of the reported rate coefficients at the 95% confidence level is estimated to be 30 - 40% depending on the temperature. Model calculations suggest that gas phase processes initiated by ozone absorption of a UV photon represent about 1.4% of the currently estimated global source strength of atmospheric N2O. However, these processes could account for a significant fraction of the oxygen mass-independent enrichment observed in atmospheric N2O, and they appear to be the first suggested photochemical mechanism that is capable of explaining the altitude dependence of the observed mass -independent isotopic signature.

Estupinan, E. G.↗

Quantum-Assisted Variational Segmentation for Image-to-Image Wildfire Detection Using Satellite Data

The quantum computing community has been searching for suitable applications to demonstrate the potential of near-term quantum devices. Quantum machine learning is a potential candidate, particularly using models that cannot be efficiently simulated with classical computers [1, 2]. This work focuses on a transition phase of quantum computers where the quantum machine learning model is still simulable classically but projected not to be simulable as the size of the model grows. Ultimately quantum computers may have advantages for high-dimensional real-world problems. Due to the limited number of qubits in current noisy intermediate-scale quantum (NISQ) devices, the direct application of quantum computers in high dimensional data is not feasible. To remedy this problem, an encoder-decoder architecture can be utilized. The encoder model would transform the high-dimensional data into a compact representation, to a level that small quantum computers can be used today (or in the near future), and the decoder would take the quantum processed outputs back to the high-dimensional space. Addressing the two challenges of quantum machine learning, this work investigates a hybrid supervised generative model with a quantum Ising Born machine embedded as the latent distribution. The model contains four main parts (Figure 1.a.): (1) a U-NET architecture responsible for learning segmentation flow, (2) a Prior network responsible for learning an encoded latent distribution of the input data, (3) a Born machine which represents the latent distribution, and (4) a Posterior network in charge of learning the joint encoded latent distribution of inputs and target data. The initial model, proposed by [3], is optimized by (1) maximizing the overlap of the prior and posterior latent distributions, and (2) minimizing the segmentation loss. The proposed model is designed to be investigated in a simulation environment applied to the real-world application of wildfire segmentation. Specifically, the model is designed to solve the patchy wildfire segmentations of Moderate Resolution Imaging Spectroradiometer (MODIS) by taking the MODIS observations and using Visible Infrared Imaging Radiometer Suite’s (VIIRS) consistent wildfire product as the target. The model solves patchy wildfire segmentations and provides insight into the epistemic errors sourced from model variation. The model utilizes the Born machine as a QUBO solver to represent the latent space as a Bernoulli distribution. The proposed configuration allows the variational segmentation model to leverage the true quantum probabilistic nature and derive a more expressive latent configuration, increasing the model performance in describing wildfire segmentations. The quantum probabilistic information of the Born machine is directly incorporated in the Kullback-Leibler divergence loss in the prior and posterior distributions, forcing the Bernoulli latent distribution to maximize the overlap of input and joint input-target distributions. The proposed model is then trained and compared with a baseline only consisting of direct Bernoulli latent distribution with no Born machine representing the latent space. The models are evaluated based on the segmentation metrics, such as precision, recall, intersect of union, with uncertainty boundaries accounting for the stochastic nature of the model. Our findings show that even in low latent-dimensional space (due to the limit in computational power of the classical quantum simulator), we are able to effectively capture the latent representation and hence the model performs better than the baseline. The findings are a projection for scaling the model into higher dimensional latent space with the Born machine surpassing the baseline performance. Figure 1. Sub-figure (a) demonstrates the architecture for the training phase. The model consists of a Prior and Posterior network that encode inputs and joint input-target data into compact representations, respectively. The Born machine represents the latent distribution, and the U-NET branch learns the segmentation patterns of the data. The stochasticity is introduced to the U-NET through its last layer to create meaningful but stochastic segmentations. Sub-figure (b) represents the inference phase where the model takes the stochastic behavior from the prior network and injects that into the U-NET. Each attempt of inference will generate different but similar segmentations from the same distribution of the wildfire event. REFERENCES [1] Coyle, B., Mills, D., Danos, V., & Kashefi, E. (2020). The Born supremacy: quantum advantage and training of an Ising Born machine. npj Quantum Information, 6(1), 1-11. [2] Liu, J. G., & Wang, L. (2018). Differentiable learning of quantum circuit born machines. Physical Review A, 98(6), 062324. [3] Kohl, S., Romera-Paredes, B., Meyer, C., De Fauw, J., Ledsam, J. R., Maier-Hein, K., ... & Ronneberger, O. (2018). A probabilistic u-net for segmentation of ambiguous images. Advances in neural information processing systems, 31.

quantum machine learning↗

A Technique Using Principal Component Analysis to Compare Seasonal Cycles of Earth Radiation from CERES and Model Computations

A method for quantitatively comparing the seasonal cycles of two global data sets is presented. The seasonal cycles of absorbed solar radiation (ASR) and outgoing longwave radiation (OLR) have been computed from an eight-year data set from the Clouds and Earth's Radiant Energy System (CERES) scanning radiometers and from a model data set produced by the NASA Goddard Space Flight Center Global Modeling and Assimilation Office. To compare the seasonal cycles from these two data sets, principal component (PC) analysis is used, where the PCs express the time variations and the corresponding empirical orthogonal functions (EOFs) describe the geographic variations. Ocean has a long thermal response time compared to land, so land and ocean are separated for the analysis. The root-mean square values for the seasonal cycles of ASR and OLR are extremely close for the two data sets. The first three PCs are quite close, showing that the time responses and magnitudes over the globe are very similar. The agreement between the two sets of PCs is quantified by computing the matrix of inner products of the two sets. For ASR over land, the first PCs of CERES and the model agree to better than 99.9%. The EOF maps are similar for most of the globe, but differ in a few places, and the agreement of the EOF maps is likewise quantified. Maps of differences between the annual cycles show regions of agreement and disagreement.

Smith, G. Louis↗

SynGenics Optimization System (SynOptSys)

The SynGenics Optimization System (SynOptSys) software application optimizes a product with respect to multiple, competing criteria using statistical Design of Experiments, Response-Surface Methodology, and the Desirability Optimization Methodology. The user is not required to be skilled in the underlying math; thus, SynOptSys can help designers and product developers overcome the barriers that prevent them from using powerful techniques to develop better pro ducts in a less costly manner. SynOpt-Sys is applicable to the design of any product or process with multiple criteria to meet, and at least two factors that influence achievement of those criteria. The user begins with a selected solution principle or system concept and a set of criteria that needs to be satisfied. The criteria may be expressed in terms of documented desirements or defined responses that the future system needs to achieve. Documented desirements can be imported into SynOptSys or created and documented directly within SynOptSys. Subsequent steps include identifying factors, specifying model order for each response, designing the experiment, running the experiment and gathering the data, analyzing the results, and determining the specifications for the optimized system. The user may also enter textual information as the project progresses. Data is easily edited within SynOptSys, and the software design enables full traceability within any step in the process, and facilitates reporting as needed. SynOptSys is unique in the way responses are defined and the nuances of the goodness associated with changes in response values for each of the responses of interest. The Desirability Optimization Methodology provides the basis of this novel feature. Moreover, this is a complete, guided design and optimization process tool with embedded math that can remain invisible to the user. It is not a standalone statistical program; it is a design and optimization system.

Ventresca, Carol↗

Hybrid automated reliability predictor integrated work station (HiREL)

The Hybrid Automated Reliability Predictor (HARP) integrated reliability (HiREL) workstation tool system marks another step toward the goal of producing a totally integrated computer aided design (CAD) workstation design capability. Since a reliability engineer must generally graphically represent a reliability model before he can solve it, the use of a graphical input description language increases productivity and decreases the incidence of error. The captured image displayed on a cathode ray tube (CRT) screen serves as a documented copy of the model and provides the data for automatic input to the HARP reliability model solver. The introduction of dependency gates to a fault tree notation allows the modeling of very large fault tolerant system models using a concise and visually recognizable and familiar graphical language. In addition to aiding in the validation of the reliability model, the concise graphical representation presents company management, regulatory agencies, and company customers a means of expressing a complex model that is readily understandable. The graphical postprocessor computer program HARPO (HARP Output) makes it possible for reliability engineers to quickly analyze huge amounts of reliability/availability data to observe trends due to exploratory design changes.

Bavuso, Salvatore J.↗

Theoretical shell-model signatures in heavy-ion, coherent pion production

A comprehensive summary of a many-body, microscopic, particle-hole formalism is presented that describes coherent, subthreshold, pion production in peripheral, heavy-ion collisions. The formalism uses a new separable model transition interaction that produces Delta-hole states in either the projectile or target nucleus. Shell-model states described by harmonic oscillator functions are used in the calculation of Delta formation and decay and Lorentz-contraction effects of the nucleus not at rest are included. An analytical expression to lowest multipole order for the differential cross section is examined. The sensitivity of the theoretical results to the shell-model states is determined with preliminary shape results compared with data. The effects of higher multipoles are examined with attention paid to the second-order multipole value.

Maung, Khin M.↗

Integrating Enhanced Grace Terrestrial Water Storage Data Into the U.S. and North American Drought Monitors

NASA's Gravity Recovery and Climate Experiment (GRACE) satellites measure time variations nf the Earth's gravity field enabling reliable detection of spatio-temporal variations in total terrestrial water storage (TWS), including ground water. The U.S. and North American Drought Monitors are two of the premier drought monitoring products available to decision-makers for assessing and minimizing drought impacts, but they rely heavily on precipitation indices and do not currently incorporate systematic observations of deep soil moisture and groundwater storage conditions. Thus GRACE has great potential to improve the Drought Monitors hy filling this observational gap. Horizontal, vertical and temporal disaggregation of the coarse-resolution GRACE TWS data has been accomplished by assimilating GRACE TWS anomalies into the Catchment Land Surface Model using ensemble Kalman smoother. The Drought Monitors combine several short-term and long-term drought indices and indicators expressed in percentiles as a reference to their historical frequency of occurrence for the location and time of year in question. To be consistent, we are in the process of generating a climatology of estimated soil moisture and ground water based on m 60-year Catchment model simulation which will subsequently be used to convert seven years of GRACE assimilated fields into soil moisture and groundwater percentiles. for systematic incorporation into the objective blends that constitute Drought Monitor baselines. At this stage we provide a preliminary evaluation of GRACE assimilated Catchment model output against independent datasets including soil moisture observations from Aqua AMSR-E and groundwater level observations from the U.S. Geological Survey's Groundwater Climate Response Network.

Housborg, Rasmus↗

A Comparison of Functional Models for Use in the Function-Failure Design Method

When failure analysis and prevention, guided by historical design knowledge, are coupled with product design at its conception, shorter design cycles are possible. By decreasing the design time of a product in this manner, design costs are reduced and the product will better suit the customer s needs. Prior work indicates that similar failure modes occur with products (or components) with similar functionality. To capitalize on this finding, a knowledge base of historical failure information linked to functionality is assembled for use by designers. One possible use for this knowledge base is within the Elemental Function-Failure Design Method (EFDM). This design methodology and failure analysis tool begins at conceptual design and keeps the designer cognizant of failures that are likely to occur based on the product s functionality. The EFDM offers potential improvement over current failure analysis methods, such as FMEA, FMECA, and Fault Tree Analysis, because it can be implemented hand in hand with other conceptual design steps and carried throughout a product s design cycle. These other failure analysis methods can only truly be effective after a physical design has been completed. The EFDM however is only as good as the knowledge base that it draws from, and therefore it is of utmost importance to develop a knowledge base that will be suitable for use across a wide spectrum of products. One fundamental question that arises in using the EFDM is: At what level of detail should functional descriptions of components be encoded? This paper explores two approaches to populating a knowledge base with actual failure occurrence information from Bell 206 helicopters. Functional models expressed at various levels of detail are investigated to determine the necessary detail for an applicable knowledge base that can be used by designers in both new designs as well as redesigns. High level and more detailed functional descriptions are derived for each failed component based on NTSB accident reports. To best record this data, standardized functional and failure mode vocabularies are used. Two separate function-failure knowledge bases are then created aid compared. Results indicate that encoding failure data using more detailed functional models allows for a more robust knowledge base. Interestingly however, when applying the EFDM, high level descriptions continue to produce useful results when using the knowledge base generated from the detailed functional models.

Stock, Michael E.↗

Effect of blunt trailing edge on rotor broadband noise

The production of high-frequency broadband noise by turbulent vortex shedding from rotor blades with blunt trailing edges is investigated analytically. The derivation of the governing equations, analogous to that of Kim and George (1982) for boundary-layer/trailing-edge noise, is explained, and numerical results are compared with the experimental data of Hubbard et al. (1981) and Lowson et al. (1972) in graphs. It is shown that vortex-shedding noise is a significant component of blunt-trailing-edge rotor broadband noise and that the analytical method employed gives reasonable predictions. The need for a better empirical expression for the normalized spectrum and for more measurements of surface pressure fluctuations near blunt trailing edges is indicated.

Chou, S.-T.↗

Vector representation of trade cumulus thermodynamic fluxes

A tephigram of BOMEX averaged thermodynamic flux vectors, developed from two tradewind budgets, is presented. The parametric model, which is utilized to represent the fluxes in the tradewind layer of the product as a mass flux and a cloud-environment difference, is examined. A table of mean structure and fluxes of a dataset for the BOMEX ship array, and the Bowen ratio and convective mass flux for a nonmixing and a cloud-top mixing model is provided. The fluxes which are displayed in a simple vector format, using the saturation point notation of Betts (1982) reveal a coupling of fluxes and the relationship between Bowen ratio and height. It is concluded that with good tradewind budget data about the statistics of cloud mixing and radiative-convective coupling can be expressed.

Betts, A. K.↗

The Ca(2+) status of the endoplasmic reticulum is altered by induction of calreticulin expression in transgenic plants

To investigate the endoplasmic reticulum (ER) Ca(2+) stores in plant cells, we generated tobacco (Nicotiana tabacum; NT1) suspension cells and Arabidopsis plants with altered levels of calreticulin (CRT), an ER-localized Ca(2+)-binding protein. NT1 cells and Arabidopsis plants were transformed with a maize (Zea mays) CRT gene in both sense and antisense orientations under the control of an Arabidopsis heat shock promoter. ER-enriched membrane fractions from NT1 cells were used to examine how altered expression of CRT affects Ca(2+) uptake and release. We found that a 2.5-fold increase in CRT led to a 2-fold increase in ATP-dependent (45)Ca(2+) accumulation in the ER-enriched fraction compared with heat-shocked wild-type controls. Furthermore, after treatment with the Ca(2+) ionophore ionomycin, ER microsomes from NT1 cells overproducing CRT showed a 2-fold increase in the amount of (45)Ca(2+) released, and a 2- to 3-fold increase in the amount of (45)Ca(2+) retained compared with wild type. These data indicate that altering the production of CRT affects the ER Ca(2+) pool. In addition, CRT transgenic Arabidopsis plants were used to determine if altered CRT levels had any physiological effects. We found that the level of CRT in heat shock-induced CRT transgenic plants correlated positively with the retention of chlorophyll when the plants were transferred from Ca(2+)-containing medium to Ca(2+)-depleted medium. Together these data are consistent with the hypothesis that increasing CRT in the ER increases the ER Ca(2+) stores and thereby enhances the survival of plants grown in low Ca(2+) medium.

NASA Discipline Plant Biology↗

Oxygen control of ethylene biosynthesis during seed development in Arabidopsis thaliana (L.) Heynh

An unforeseen side-effect on plant growth in reduced oxygen is the loss of seed production at concentrations around 25% atmospheric (50 mmol mol-1 O2). In this study, the model plant Arabidopsis thaliana (L.) Heynh. cv. 'Columbia' was used to investigate the effect of low oxygen on ethylene biosynthesis during seed development. Plants were grown in a range of oxygen concentrations (210 [equal to ambient], 160, 100, 50 and 25 mmol mol-1) with 0.35 mmol mol-1 CO2 in N2. Ethylene in full-sized siliques was sampled using gas chromatography, and viable seed production was determined at maturity. Molecular analysis of ethylene biosynthesis was accomplished using cDNAs encoding 1-aminocyclopropane-1-carboxylic acid (ACC) synthase and ACC oxidase in ribonuclease protection assays and in situ hybridizations. No ethylene was detected in siliques from plants grown at 50 and 25 mmol mol-1 O2. At the same time, silique ACC oxidase mRNA increased three-fold comparing plants grown under the lowest oxygen with ambient controls, whereas ACC synthase mRNA was unaffected. As O2 decreased, tissue-specific patterning of ACC oxidase and ACC synthase gene expression shifted from the embryo to the silique wall. These data demonstrate how low O2 modulates the activity and expression of the ethylene biosynthetic pathway during seed development in Arabidopsis.

NASA Discipline Plant Biology↗

Effect of Gravity Level on the Particle Shape and Size During Zeolite Crystal Growth

A microscopic diffusion model is developed to represent solute transport in the boundary layer of a growing zeolite crystal. This model is used to describe the effect of gravity on particle shape and solute distribution. Particle dynamics and crystal growth kinetics serve as the boundary conditions of flow and convection-diffusion equations. A statistical rate theory is used to obtain the rate of solute transport across the growing interface, which is expressed in terms of concentration and velocity of solute species. Microgravity can significantly decrease the solute velocity across the growing interface compared to its earth-based counterpart. The extent of this reduction highly depends on solute diffusion constant in solution. Under gravity, the flow towards the crystal enhances solute transport rate across the growing interface while the flow away from crystals reduces this rate, suggesting a non-uniform growth rate and thus an elliptic final shape. However, microgravity can significantly reduce the influence of flow and obtain a final product with perfect spherical shape. The model predictions compare favorably with the data of space experiment of zeolites grown in space.

Song, Hong-Wei↗

Preventing Molecular and Particulate Infiltration in a Confined Volume

Contaminants from an instrument's self-generated sources or from sources external to the instrument may degrade its critical surfaces and/or create an environment which limits the instrument's intended performance. Analyses have been carried out on a method to investigate the required purging flow of clean, dry gas to prevent the ingestion of external contaminants into the instrument container volume. The pressure to be maintained and the required flow are examined in terms of their effectiveness in preventing gaseous and particulate contaminant ingestion and abatement of self-generated contaminants in the volume. The required venting area or the existing volume venting area is correlated to the volume to be purged, the allowable pressure differential across the volume, the external contaminant partial pressure, and the sizes of the ambient particulates. The diffusion of external water vapor into the volume while it was being purged was experimentally obtained in terms of an infiltration time constant. That data and the acceptable fraction of the outside pressure into the volume indicate the required flow of purge gas expressed in terms of volume change per unit time. The exclusion of particulates is based on the incoming velocity of the particles and the exit flow speed and density of the purge gas. The purging flow pressures needed to maintain the required flows through the vent passages are indicated. The purge gas must prevent or limit the entrance of the external contaminants to the critical locations of the instrument. It should also prevent self- contamination from surfaces, reduce material outgassing, and sweep out the outgassed products. Systems and facilities that can benefit from purging may be optical equipment, clinical facilities, manufacturing facilities, clean rooms, and other systems requiring clean environments.

Scialdone, John J.↗

Transcriptomic Analysis of ISS Crewmembers’ Peripheral Blood Mononuclear Cells Reveals Homeostatic Regulations in Space

The impact of spaceflight on the immune system has been investigated for decades. Studies conducted in cell models, animals and humans suggest that the spaceflight environment affects the innate and acquired immune systems, as the ability to recognize antigens, defend against foreign invaders, and orchestrate repair is significantly hindered. However, the molecular mechanisms behind spaceflight-induced immune dysregulations are still unclear. In this study, blood from eleven (11) International Space Station (ISS) crewmembers was collected before, during and after long duration space missions, as well as from 11 matched ground control subjects. Transcriptomic analysis was performed in isolated peripheral blood mononuclear cells (PBMCs) using the RNA-sequencing technique. In comparison to the blood samples collected from the crewmembers pre-flight, a total of ~1000 genes were found to be upregulated and ~1000 genes downregulated in PBMC collected between 4 and 6 months after they were in space. The most significantly DEGs (differentially expressed genes) include activation of RUBCNL which is an autophagy enhancer and inhibition of GRASP which regulates cell trafficking. Genes involved in cell adhesion, cell cycle progression and other functions were also dysregulated. Pathway analysis of the DEGs indicates mitochondria dysfunction, particularly reduced ATP production in the electron transport chain. Other pathways impacted by spaceflight include glycolysis, autophagy and inflammatory response. Our results suggest that, in space, blood cells may have also experienced energy depletion and reduced metabolism. Consequently, the cells may become autophagic, which is a known homeostatic mechanism for blood cells to become quiescent, but to stay alive. Further analysis of the data shows recovery of the crewmembers after mission and potential differential responses between genders to the space environment. Our data potentially explains some of the physiological changes that have been observed in space such as mitochondria dysfunction, inhibition of T cell activation and telomere lengthening. Comparison of our results with other transcriptomics studies of ISS crewmembers’ blood cells will also be presented.

Maria Moreno Villanueva↗

The evolution of enstatite and chondrules in unequilibrated enstatite chondrites: Evidence from iron-rich pyroxene

FeO-rich (Fs(sub 6)-34) pyroxene lacking cathodoluminescence (CL), hereafter black pyroxene, is a major constituent of some of the chondrules and fragments in unequilibrated (type 3) enstatite chondrites (UECs). It contains structurally oriented zones of Cr-, Mn-, V-rich, FeO-poor enstatite with red CL, associated with mm-sized blebs of low-Ni, Fe-metal and, in some cases, silica. These occurrences represent clear evidence of pyroxene reduction. The black pyroxene is nearly always rimmed by minor element (Cr, Mn, V)-poor enstatite having a blue CL. More commonly, red and blue enstatites, unassociated with black pyroxene, occur as larger grains in chondrules and fragments, and these constitute the major silicate phases in UECs. The rare earth element (REE) abundance patterns of the black pyroxene are LREE-depleted. The blue enstatite rims, however, have a near-flat to LREE-enriched pattern, approx. 0.5-4x chondritic. The petrologic and trace element data indicate that the black pyroxene is from an earlier generation of chondrules that formed in a nebular region that was more oxidizing than that of the enstatite chondrites. Following solidification, these chondrules experienced a more reducing nebular environment and underwent reduction. Some, perhaps most, of the red enstatite that is common throughout the UECs may be the product of solid-state reduction of black pyroxene. The blue enstatite rims grew onto the surfaces of the black pyroxene and red enstatite as a result of condensation from a nebular gas. The evolutionary history of some of the enstatite and chondrules in enstatite chondrites can be expressed in a four-stage model that includes: Stage 1. Formation of chondrules in an oxidizing nebular environment. Stage 2. Solid-state reduction of the more oxidized chondrules and fragments to red enstatite in a more reducing nebular environment. Stage 3. Formation of blue enstatite rims on the black pyroxene as well as on the red enstatite. Stage 4. Reprocessing, by various degrees of melting, of many of the earlier-formed materials.

Weisberg, Michael K.↗

A Method for Retrieving Ground Flash Fraction from Satellite Lightning Imager Data

A general theory for retrieving the fraction of ground flashes in N lightning observed by a satellite-based lightning imager is provided. An "exponential model" is applied as a physically reasonable constraint to describe the measured optical parameter distributions, and population statistics (i.e., mean, variance) are invoked to add additional constraints to the retrieval process. The retrieval itself is expressed in terms of a Bayesian inference, and the Maximum A Posteriori (MAP) solution is obtained. The approach is tested by performing simulated retrievals, and retrieval error statistics are provided. The ability to retrieve ground flash fraction has important benefits to the atmospheric chemistry community. For example, using the method to partition the existing satellite global lightning climatology into separate ground and cloud flash climatologies will improve estimates of lightning nitrogen oxides (NOx) production; this in turn will improve both regional air quality and global chemistry/climate model predictions.

Koshak, William J.↗

Extracellular calcium (Ca2+(o))-sensing receptor in a murine bone marrow-derived stromal cell line (ST2): potential mediator of the actions of Ca2+(o) on the function of ST2 cells

The calcium-sensing receptor (CaR) is a G protein-coupled receptor that plays key roles in extracellular calcium ion (Ca2+(o)) homeostasis by mediating the actions of Ca2+(o) on parathyroid gland and kidney. Bone marrow stromal cells support the formation of osteoclasts from their progenitors as well as the growth of hematopoietic stem cells by secreting humoral factors and through cell to cell contact. Stromal cells also have the capacity to differentiate into bone-forming osteoblasts. Bone resorption by osteoclasts probably produces substantial local increases in Ca2+(o) that could provide a signal for stromal cells in the immediate vicinity, leading us to determine whether such stromal cells express the CaR. In this study, we used the murine bone marrow-derived, stromal cell line, ST2. Both immunocytochemistry and Western blot analysis, using an antiserum specific for the CaR, detected CaR protein in ST2 cells. We also identified CaR transcripts in ST2 cells by Northern analysis using a CaR-specific probe and by RT-PCR with CaR-specific primers, followed by nucleotide sequencing of the amplified products. Exposure of ST2 cells to high Ca2+(o) (4.8 mM) or to the polycationic CaR agonists, neomycin (300 microM) or gadolinium (100 microM), stimulated both chemotaxis and DNA synthesis in ST2 cells. Therefore, taken together, our data strongly suggest that the bone marrow-derived stromal cell line, ST2, possesses both CaR protein and messenger RNA that are very similar if not identical to those in parathyroid and kidney. Furthermore, as ST2 cells have the potential to differentiate into osteoblasts, the CaR in stromal cells could participate in bone turnover by stimulating the proliferation and migration of such cells to sites of bone resorption as a result of local, osteoclast-mediated release of Ca2+(o) and, thereafter, initiating bone formation after their differentiation into osteoblasts.

NASA Discipline Musculoskeletal↗