Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPLOSIONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

HERMES: A model to describe deformation, burning, explosion, and detonation

HERMES (High Explosive Response to MEchanical Stimulus) was developed to fill the need for a model to describe an explosive response of the type described as BVR (Burn to Violent Response) or HEVR (High Explosive Violent Response). Characteristically this response leaves a substantial amount of explosive unconsumed, the time to reaction is long, and the peak pressure developed is low. In contrast, detonations characteristically consume all explosive present, the time to reaction is short, and peak pressures are high. However, most of the previous models to describe explosive response were models for detonation. The earliest models to describe the response of explosives to mechanical stimulus in computer simulations were applied to intentional detonation (performance) of nearly ideal explosives. In this case, an ideal explosive is one with a vanishingly small reaction zone. A detonation is supersonic with respect to the undetonated explosive (reactant). The reactant cannot respond to the pressure of the detonation before the detonation front arrives, so the precise compressibility of the reactant does not matter. Further, the mesh sizes that were practical for the computer resources then available were large with respect to the reaction zone. As a result, methods then used to model detonations, known as β-burn or program burn, were not intended to resolve the structure of the reaction zone. Instead, these methods spread the detonation front over a few finite-difference zones, in the same spirit that artificial viscosity is used to spread the shock front in inert materials over a few finite-difference zones. These methods are still widely used when the structure of the reaction zone and the build-up to detonation are unimportant. Later detonation models resolved the reaction zone. These models were applied both to performance, particularly as it is affected by the size of the charge, and to situations in which the stimulus was less than that needed for reliable performance, whether as a result of accident, hazard, or a fault in the detonation train. These models describe the build-up of detonation from a shock stimulus. They are generally consistent with the mesoscale picture of ignition at many small defects in the plane of the shock front and the growth of the resulting hot-spots, leading to detonation in heterogeneous explosives such as plastic-bonded explosives (PBX). The models included terms for ignition, and also for the growth of reaction as tracked by the local mass fraction of product gas, {lambda}. The growth of reaction in such models incorporates a form factor that describes the change of surface area per unit volume (specific surface area) as the reaction progresses. For unimolecular crystalline-based explosives, the form factor is consistent with the mesoscale picture of a galaxy of hot spots burning outward and eventually interacting with each other. For composite explosives and propellants, where the fuel and oxidizer are segregated, the diffusion flame at the fuel-oxidizer interface can be interpreted with a different form factor that corresponds to grains burning inward from their surfaces. The form factor influences the energy release rate, and the amount of energy released in the reaction zone. Since the 19 th century, gun and cannon propellants have used perforated geometric shapes that produce an increasing surface area as the propellant burns. This helps maintain the pressure as burning continues while the projectile travels down the barrel, which thereby increases the volume of the hot gas. Interior ballistics calculations use a geometric form factor to describe the changing surface area precisely. As a result, with a suitably modified form factor, detonation models can represent burning and explosion in damaged and broken reactant. The disadvantage of such models in application to accidents is that the ignition term does not distinguish between a value of pressure that results from a shock, and the same pressure that results from a more gradual increase. This disagrees with experiments, where explosives were subjected to a gradual rise in pressure and did not exhibit reaction. More recent models do distinguish between slow pressure rises and shocks, and have had some success in the describing the response of explosives to single and multiple shocks, and the increase of shock sensitivity with porosity, at least over a limited range. The original formulation is appropriate for sustained shocks, but further work is ongoing to describe the response to short pulses. The HERMES model combines features from these prior models. It describes burning and explosion in damaged reactant, and also will develop a detonation if the gradual rise in pressure from burning steepens into a strong-enough shock. The shock strength needed for detonation in a fixed run distance decreases with increasing porosity.

36 MATERIALS SCIENCE↗

Detonation Waves in High Explosives

A material at high temperature can react or decompose. For an energetic material, the reaction is exothermic and releases chemical energy that would further increase the temperature. Under some circumstances, when a reaction is triggered, such a reaction can propagate and the material rapidly releases a large amount of energy giving rise to an explosion. Examples of such materials are aerosols, suspensions of solid particles or liquid droplets in a gas; such as coal dust, grain dust and fuel-air explosions. Frequently, explosions are due to accidents. A spectacularly destructive example is the recent explosion of a large quantity of ammonium nitrate (thousands of tons) in Beirut, Lebanon (August 2020); see for example Beirut explosion. Ammonium nitrate is used as a fertilizer. It and the aerosols are not considered to be explosives due to the limited conditions for which an explosion can occur. An aerosol gets the oxidizer from the surrounding air. Burning requires diffusion of the oxidizer to the particle surface where the reaction occurs. A large density of small particles is required for a fast enough reaction to support an explosion. In contrast, an explosive is an energetic material with both fuel and oxidizer mixed on a molecular scale (either premixed gases or within molecules of a solid). This allows fast enough reactions over a wide range of conditions to support a self-propagating reactive wave known as a detonation wave. A detonation wave can be controlled and an explosive used for useful purposes such as in mining, construction, demolition, explosive welding, argon flash lamp, pulsed power using a magnetic flux generator [see also Goforth et al., 2015], jet cutter with shaped charge, explosive art, and generating conditions to study the response of materials at high strain rates and high pressures [see for example, Marsh, 1980]. Explosives are also used in conventional munitions and nuclear weapons. The focus of this book is on the theory and phenomenology of solid high explosives (HEs); in particular, plastic-bonded explosives (PBXs). Some aspects of detonation wave theory are needed to interpret explosive data. Hence, the theory is presented before the detonation wave phenomenology. A familiarity with fluid flow, specifically the notion of shock waves and the shock loci are assumed. In the remainder of this chapter we give a brief overview on the basic properties of detonation waves and PBXs.

36 MATERIALS SCIENCE↗

RCRA PART B Permit Application Nevada National Security Site (NNSS) for Waste Management Activities at the NNSS Explosive Ordnance Disposal Unit (EODU)

This volume of the Resource Conservation and Recovery Act (RCRA) permit application by the Department of Energy, National Nuclear Security Administration Nevada Field Office (NNSA/NFO) seeks continued operation of the Explosive Ordnance Disposal Unit (EODU) at the Nevada National Security Site (NNSS). Explosives, explosive materials, and unexploded ordnance are declared waste explosives if they are damaged, are defective, have exceeded their shelf life, are the result of environmental restoration (legacy), or are discarded explosive material from research or testing projects. This document provides a description of the regulated waste codes accepted for treatment (controlled detonations), the general design of the unit, and the processes used to safely detonate onsite-generated waste explosives and unexploded ordnance, which are defined as hazardous waste under specific regulations. The Area 11 EODU consists of a firing point (controlled access area where firing of explosives is conducted), firing pad (prepares site where explosives hazardous waste is fired), and ancillary equipment that includes an explosives magazine and firing point area. Additionally, live explosives training is conducted to ensure proficiency of the EODU operations personnel, explosives handlers, and the firing system components. Training detonations do not include waste explosives and are limited in respect to explosives volume and frequency personnel, explosives handlers, and the firing system components. Training detonations do not include waste explosives and are limited in respect to explosives volume and frequency. For safety and security reasons, some of the contents of the full application are not available for public viewing. This public version of the application contains most, but not all, of the contents as submitted to the regulatory agencies.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Date Release Report for Large Surface Explosion Coupling Experiment (LSECE) Nevada National Security Site

The DTRA sponsored 2020-2022 Large Surface Explosion Coupling Experiment (LSECE) consists of two large ground surface chemical explosions, data collection, analysis and modeling carried out in 2020-2022. The LSECE chemical explosions were carried out at the site of prior NNSA sponsored buried chemical explosions that were part of the Source Physics Experiment (SPE) Phase II in Dry Alluvium Geology (DAG). This report described the data collected under LSECE that is being made publicly available. The prior buried explosion DAG data are described in a separate report (https://www.osti.gov/biblio/1825534) and are also publicly available. The LSECE explosions, data analysis and numerical modeling work sponsored by DTRA were intended to address three objectives: 1) Generate seismo-acoustic data to test and improve numerical models of explosion energy coupling in dry alluvium geology; 2) To improve seismo-acoustic yield estimation techniques as a function of depth and medium properties; 3) To study and improve acoustic propagation modeling under two different atmospheric conditions. The LSECE data that were collected have expanded the prior DAG buried explosion dataset to include surface chemical explosions recorded on a common set of seismo-acoustic stations. They have allowed a more detailed study of above and below surface seismo-acoustic energy coupling with applications to explosion monitoring and assessment. The two approximately 1-ton TNT equivalent yield LSECE explosions were detonated at different times of the day to explore the effects of the different atmospheric conditions. The first chemical explosion “Artemis” was conducted before dawn when temperature inversions were present. The second chemical explosion “Apollo” was conducted on a sunny afternoon when the temperature gradient was more linear. The LSECE chemical explosion data were also collected across a variety of different sensor types to allow evaluation of their effectiveness in recovering useful information. The LSECE instrumentation included fiber optic or Distributed Acoustic Sensing (DAS), a dense array or Large-N array of seismometers, borehole accelerometers, DAS and a velocity meter, airborne acoustic instruments and a variety of visual and remote sensing data.

58 GEOSCIENCES↗

Simulation Study of Near-Surface Coupling of Nuclear Devices vs. Equivalent High-Explosive Charges

A computational study was performed to examine the differences in near-surface ground-waves and air-blast waves generated by high-explosive energy sources and those generated by much higher energy - density low - yield nuclear sources. The study examined the effect of explosive-source emplacement (i.e., height-of-burst, HOB, or depth-of-burial, DOB) over a range from depths of -35m to heights of 20m, for explosions with an explosive yield of 1-kt . The chemical explosive was modeled by a JWL equation-of-state model for a ~14m diameter sphere of ANFO (~1,200,000kg – 1 k t equivalent yield ), and the high-energy-density source was modeled as a one tonne (1000 kg) plasma of ‘Iron-gas’ (utilizing LLNL’s tabular equation-of-state database, LEOS) in a 2m diameter sphere, with a total internal-energy content equivalent to 1 k t . A consistent equivalent-yield coupling-factor approach was developed to compare the behavior of the two sources. The results indicate that the equivalent-yield coupling-factor for air-blasts from 1 k t ANFO explosions varies monotonically and continuously from a nearly perfec t reflected wave off of the ground surface for a HOB ≈ 20m, to a coupling factor of nearly zero at DOB ≈ -25m. The nuclear air - blast coupling curve, on the other hand, remained nearly equal to a perfectly reflected wave all the way down to HOB’s very near zero, and then quickly dropped to a value near zero for explosions with a DOB ≈ -10m. The near - surface ground - wave traveling horizontally out from the explosive source region to distances of 100’s of meters exhibited equivalent - yield coupling - factors t hat varied nearly linearly with HOB/DOB for the simulated ANFO explosive source, going from a value near zero at HOB ≈ 5m to nearly one at DOB ≈ -25m. The nuclear-source generated near-surface ground wave coupling-factor remained near zero for almost all HOB’s greater than zero, and then appeared to vary nearly - linearly with depth-of-burial until it reached a value of one at a DOB between 15m and 20m. These simulations confirm the expected result that the variation of coupling to the ground, or the air, change s much more rapidly with emplacement location for a high-energy-density (i.e., nuclear-like) explosive source than it does for relatively low - energy - density chemical explosive sources. The Energy Partitioning, Energy Coupling (EPEC) platform at LLNL utilizes laser energy from one quad (i.e. 4-laser beams) of the 192 - beam NIF Laser bank to deliver ~10kJ of energy to 1mg of silver in a hohlraum creating an effective small-explosive ‘source’ with an energy density comparable to those in low-yield nuclear devices. Such experiments have the potential to provide direct experimental confirmation of the simulation results obtained in this study, at a physical scale (and time-scale) which is a factor of 1000 smaller than the spatial- or temporal-scales typically encountered when dealing with nuclear explosions.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

LLNL Macroscopic Anisotropic Explosives Research at INL National Security Test Range - Test Results

A select team of 23 engineers, scientists, and explosives specialists from LLNL, LANL, INL, and Marine Raiders from Marine Special Operations Command (MARSOC) and U.S. Special Operations Command (SOCOM) assembled during the second week of November at the INL National Security Test Range near Idaho Falls to investigate and demonstrate fundamental principles of explosives anisotropy. Today's explosives are isotropic in their detonation performance. That is, no matter what direction a detonation runs through bulk explosive, the performance is the same; whereas, anisotropic explosives exhibit different performance, depending on which direction the detonation wave moves through the explosive. The ANISO Team worked in subfreezing temperatures on the Snake River Plain, carrying out 55 experimental explosives shots in four days that lead to a clear understanding of the performance and behavior of an assembly of small, linerless, C4 shaped charges. These shots clearly demonstrated, for the first time, on a macroscopic scale, the principle of anisotropy in measured progression of the detonation through the explosive assembly. The outputs of nine piezo timing pins in the explosive assembly clearly showed detonation progressing through the assembly faster than nominal detonation velocity and moving slower than nominal detonation velocity in the opposite direction. Basic data from these experiments will be used to design and construct explosives assemblies that will be shot in the LLNL High Explosives Applications Facility's (HEAF). These experimental tests will provide refined basic data that will then be used by modelers to develop high explosives models. Computer simulations using these models will then be run to predict performance and design inhomogeneous, anisotropic bulk explosive charges that will be tested at LLNL.

33 ADVANCED PROPULSION SYSTEMS↗

Low Frequency Electromagnetic Pulse and Explosions

This paper reviews and summarizes prior work related to low frequency (< 100 Hz) EMP (ElectroMagnetic Pulse) observed from explosions. It focuses on how EMP signals might, or might not, be useful in monitoring underground nuclear tests, based on the limits of detection, and physical understanding of these signals. In summary: (1) Both chemical and nuclear explosions produce an EMP. (2) The amplitude of the EMP from underground explosions is at least two orders of magnitude lower than from above ground explosions and higher frequency components of the signal are rapidly attenuated due to ground conductivity. (3) In general, in the near field, that is distances (r) of less than 10s of kilometers from the source, the amplitude of the EMP decays approximately as 1/r{sup 3}, which practically limits EMP applications to very close (<{approx}1km) distances. (4) One computational model suggests that the EMP from a decoupled nuclear explosion may be enhanced over the fully coupled case. This has not been validated with laboratory or field data. (5) The magnitude of the EMP from an underground nuclear explosion is about two orders of magnitude larger than that from a chemical explosion, and has a larger component of higher frequencies. In principle these differences might be used to discriminate a nuclear from a chemical explosion using sensors at very close (<{approx}1 km) distances. (6) Arming and firing systems (e.g. detonators, exploding bridge wires) can also produce an EMP from any type of explosion. (7) To develop the understanding needed to apply low frequency EMP to nuclear explosion monitoring, it is recommended to carry out a series of controlled underground chemical explosions with a variety of sizes, emplacements (e.g. fully coupled and decoupled), and arming and firing systems.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Planar blast scaling with condensed-phase explosives in a shock tube

Blast waves are strong shock waves that result from large power density deposition into a fluid. The rapid energy release of high-explosive (HE) detonation provides sufficiently high power density for blast wave generation. Often it is desirable to quantify the energy released by such an event and to determine that energy relative to other reference explosives to derive an explosive-equivalence value. In this study, we use condensed-phase explosives to drive a blast wave in a shock tube. The explosive material and quantity were varied to produce blast waves of differing strengths. Pressure transducers at varying lengths measured the post-shock pressure, shock-wave arrival time and sidewall impulse associated with each test. Blast-scaling concepts in a one-dimensional geometry were then used to both determine the energy release associated with each test and to verify the scaling of the shock position versus time, overpressure versus distance, and impulse. Most blast scaling measurements to-date have been performed in a three-dimensional geometry such as a blast arena. Testing in a three-dimensional geometry can be challenging, however, as spherical shock-wave symmetry is required for good measurements. Additionally, the spherical wave strength decays rapidly with distance and it can be necessary to utilize larger (several kg) quantities of explosive to prevent significant decay from occurring before an idealized blast wave has formed. Such a mode of testing can be expensive, require large quantities of explosive, and be limited by both atmospheric conditions (such as rain) and by noise complaints from the population density near the test arena. Testing is possible in more compact geometries, however. Non-planar blast waves can be formed into a quasi-planar shape by confining the shock diffraction with the walls of a shock tube. Regardless of the initial form, the wave shape will begin to approximate a planar front after successive wave reflections from the tube walls. Such a technique has previously been used to obtain blast scaling measurements in the planar geometry with gaseous explosives and the condensed-phase explosive nitroguanidine. Recently, there has been much interest in the blast characterization of various non-ideal high explosive (NIHE) materials. With non-ideals, the detonation reaction zone is significantly larger (up to several cm for ANFO) than more ideal explosives. Wave curvature, induced by charge-geometry, can significantly affect the energy release associated with NIHEs. To measure maximum NIHE energy release accurately, it is desirable to minimize any such curvature and, if possible, to overdrive the detonation shock to ensure completion of chemical reactions ahead of the sonic locus associated with the reaction zone. This is achieved in the current study through use of a powerful booster HE and a charge geometry consisting of short cylindrical lengths of NIHE initiated along the charge centerline.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Review of potential impacts to sea turtles from underwater explosive removal of offshore structures

The purpose of this study was to collect and synthesize existing information relevant to the explosive removal of offshore structures (EROS) in aquatic environments. Data sources were organized and summarized by topic - explosive removal methods, physics of underwater explosions, sea turtle resources, documented impacts to sea turtles, and mitigation of effects. Information was gathered via electronic database searches and literature source review. Bulk explosive charges are the most commonly used technique in EROS. While the physical principles of underwater detonations and the propagation of pressure and acoustic waves are well understood, there are significant gaps in the application of this knowledge. Impacts to sea turtles from explosive removal operations may range from non-injurious effects (e.g. acoustic annoyance; mild tactile detection or physical discomfort) to varying levels of injury (i.e. non-lethal and lethal injuries). Very little information exists regarding the impacts of underwater explosions on sea turtles. Effects of explosions on turtles often must be inferred from documented effects to other vertebrates with lungs or other gas-containing organs, such as mammals and most fishes. However, a cautious approach should be used when determining impacts to sea turtles based on extrapolations from other vertebrates. The discovery of beached sea turtles and bottlenose dolphins following an explosive platform removal event in 1986 prompted the initiation of formal consultation between the U.S. Department of the Interior, Minerals Management Service (MMS) and the National Marine Fisheries Service (NMFS), authorized through the Endangered Species Act Section 7, to determine a mechanism to minimize potential impacts to listed species. The initial consultation resulted in a requirement for oil and gas companies to obtain a permit (through separate consultations on a case-by-case basis) prior to using explosives in Federal waters. Because many offshore structure removal operations are similar, a 'generic' Incidental Take Statement was established by the NMFS that describes requirements to protect sea turtles when an operator's individual charge weights did not exceed 50 lb (23 kg). Requirements associated with the Incidental Take Permit were revised in 2003 and 2006 to accommodate advances in explosive charge technologies, removals of structures in deeper waters, and adequate protection of deep water marine mammal species in Gulf of Mexico waters. Generally, these requirements include pre- and post-detonation visual monitoring using standard surface and aerial survey methods for sea turtles and marine mammals, and, in some scenarios, passive acoustic survey methods for marine mammals within a specified radius from an offshore structure. The survey program has been successful in mitigating impacts to sea turtles associated with EROS. However, even with these protective measures in place, there have been observations of sea turtles affected by explosive platform removals.

54 ENVIRONMENTAL SCIENCES↗

Effects of Model Uncertainties in Underground Chemical Explosions on Far-field Results

We used the CTH shock physics code to simulate the explosion of an 18-t chemical explosive at a depth of 250 m. We used the CTH in the two-dimensional axisymmetric (cylindrical) geometry (2DC) and most simulations included fully tamped explosions in wet tuff. Our study focused on parametric studies of three of the traditional strength models available in CTH, namely, geologic-yield, elastic perfectly-plastic von Mises, and Johnson-Cook strength (flow stress) models. We processed CTH results through a code that generates Reduced Displacement Potential (RDP) histories for each simulation. Since RDP is the solution of the linear wave equation in spherical coordinates, it is mainly valid at far-enough distance from the explosion the elastic radius. Among various parameters examined, we found the yield strength to have the greatest effect on the resulting RDP, where the peak RDP reduces almost linearly in log-log space as the yield strength increases. Moreover, an underground chemical explosion results in a cavity whose final diameter is inversely proportional to the material yield strength, i.e., as the material's yield strength increases the resulting final cavity radius decreases. Additionally, we found the choice of explosive material (COMP-C4 versus COMP-B) has minor effects on the peak RDP, where denser COMP-C4 shows higher peak RDP than the less dense COMP-B by a factor of ~1.1. In addition to wet tuff, we studied explosions in dry tuff, salt, and basalt, for a single strength model and yield strength value. We found wet tuff has the highest peak RDP value, followed by dry tuff, salt, and basalt. 2DC simulations of explosions in 11 m radius spherical, hemispherical, and cylindrical cavities showed the RDP signals have much lower magnitude than tamped explosions, where the cavity explosions mimicked nearly decoupled explosions.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Explosion behavior investigation and safety assessment of large-format lithium-ion pouch cells

We report large-format lithium-ion (Li-ion) batteries with high energy density for electric vehicles are prone to thermal runaway (or even explosion) under abusive conditions. In this study, overcharge induced explosion behaviors of large-format Li-ion pouch cells with Li[Ni 0.8 Co 0.1 Mn 0.1 ]O 2 cathode at different current rates (C-rates) (0.5C, 1C, 2C) were investigated. The explosion characteristics of the cells were elucidated by discussing the evolution of the cell voltage, the surface temperature and the shock wave pressure. Generally, the whole overcharge process could be divided into four stages according to the evolution of several key parameters and the overcharge behaviors; the overcharge C-rate has a great influence on cells’ thermal behaviors. The experimental results showed that the thermal runaway process of Li-ion cells caused by overcharging consisted of two kinds of explosions, physical explosion and chemical explosion. The existence of observable negative pressure zone in the pressure curves indicated that the Li-ion cells are not a self-supplying oxygen system during the explosion. Further, the explosion dynamics parameters were matched. An explosion TNT-equivalent conversion strategy that depended on the pressure of the shock wave was utilized to evaluate the released energy and its hazards. In addition, with respect to the overcharge of Li-ion pouch cells, a safety assessment method and a safety management method were proposed based on the explosion behaviors. From the perspective of battery safety, this study is of great significance for the safety design of Li-ion cells and can provide guidance for engineers to optimize the safety function of battery packs.

25 ENERGY STORAGE↗

Risk Assessment in a Chemical Laboratory Following an Explosive Incident Involving a Novel Diazonium Compound: Retrospective Analysis and Lessons Learned

Diazonium compounds are synthetically useful in the production of dyes and textiles, however they are highly explosive under dry conditions. Explosion prevention becomes more difficult when new diazonium compounds are synthesized, because while some syntheses include a counterion to increase their stability, this is not always a reliable method to prevent an explosive incident. Due to the uncertainty surrounding the explosiveness of different diazonium compounds, it is important to understand how to safely clean up after an incident and how to determine when it is safe to return a laboratory to typical operational use, particularly when the incident involves a novel compound where a standard does not exist for instrument calibration. Here, an explosive event is discussed involving the synthesis of 4-bromo-benzenediazonium-2-carboxylate. Following the explosive incident and 3-step cleanup, which involved a precautionary neutralization step, samples were collected from the fume hood where the incident occurred. Because the incident involved an unstable, novel compound that is not commercially available and was deemed unsafe to resynthesize for instrument calibration, we assessed the risk of further explosion by analyzing for the stable decomposition products. Mass spectrometry analysis confirmed that the residue in the fume hood contained 5-bromosalicylic acid, a decomposition product of 4-bromo-benzenediazonium-2-carboxylate. Samples were taken from multiple points in the fume hood and analyzed to estimate the spatial distribution of the decomposition product. Based on this analysis, we inferred that the primary decomposition product was far more abundant than residual energetic, indicating the energetic had been consumed or neutralized to a trace quantity where the risk of further explosion was low. Furthermore, the steps presented here─specifically, initial neutralization and then analyzing the spatial distribution of expected decomposition products to assess risk when a novel explosive material is detonated in a confined space─were our approach to assess further risk following an explosion due to a novel diazonium compound without the need for any further handling or resynthesis of the energetic. Here, we present our approach and critically analyze these steps by discussing retrospective lessons learned and alternative analytical approaches.

Computer simulations↗

Progress in model development to quantify High Explosive Violent Response (HEVR) to mechancial insult

The rapid release of chemical energy has found application for industrial and military purposes since the invention of gunpowder. Black powder, smokeless powder of various compositions, and pyrotechnics all exhibit the rapid release of energy without detonation when they are being used as designed. The rapidity of energy release for these materials is controlled by adjustments to the particle surface area (propellant grain configuration or powder particle size) in conjunction with the measured pressure-dependent burning rate, which is very subsonic. In this way a manufacturing process can be used to engineer the desired violence of the explosion. Detonations in molecular explosives, in contrast, propagate with a supersonic velocity that depends on the loading density, but is independent of the surface area. In ideal detonations, the reaction is complete within a small distance of the propagating shock front. Non-ideal detonations in molecular and composite explosives proceed with a slower velocity, and the reaction may continue well behind the shock front. We are developing models to describe the circumstances when molecular and composite explosives undergo a rapid release of energy without detonating. The models also apply to the behavior of rocket propellants subject to mechanical insult, whether for accidents (Hazards) or the suite of standardized tests used to assess whether the system can be designated an Insensitive Munition (IM). In the application described here, we are studying an HMX (1,3,5,7-tetranitro-1,3,5,7-tetraazacyclooctane) explosive developed in the UK, which is 91% by weight HMX and 9% binder-plasticizer. Most explosives and propellants, when subjected to a mechanical insult, drop or impact that is well below the threshold for detonation have been observed to react violently. This behavior is known as High Explosive Violent Reaction (HEVR). The basis of our model is the observation that the mechanical insult produces damage in a volume of the explosive near the trajectory of the impactor. The damage is manifest as surface area through the creation of cracks and fragments, and also as porosity through the separation of crack faces and isolation of the fragments. Open porosity permits a flame to spread easily and so ignite the surface area that was created. The surface area itself leads to in increase in the mass-burning rate. As the kinetic energy and power of the insult increases, the degree of damage and the volume of damage both increase. Upon a localized ignition, the flame spreads to envelop the damaged volume, and the pressure rises at an accelerated rate until neither mechanical strength nor inertial confinement can successfully contain the pressure. The confining structure begins to expand. This reduces the pressure and may even extinguish the flame. Both the mass of explosive involved and the rate at which the gas is produced contribute to each of several different measures of violence. Such measures include damage to the confinement, the velocity and fragment size distributions from what was the confinement, and air blast. Figure 1 illustrates the interaction of the various phenomena described above. Our model comprises several interacting elements. The production of damage, the ignition criterion, the mass rate of burning (reaction rate), the equations of state and constitutive models of the solid explosive reactant (unburned) and gas products, flame propagation in damaged reactant, and the progressive failure of the confinement are all elements of the model. The model is intended for implementation in a general-purpose simulation program (hydrocode) that solves the partial differential equations for the conservation of mass, momentum, and energy in conjunction with equations of state and strength.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Quantum Cascade Lasers (QCLs) for standoff explosives detection : LDRD 138733 final report.

Continued acts of terrorism using explosive materials throughout the world have led to great interest in explosives detection technology, especially technologies that have a potential for remote or standoff detection. This LDRD was undertaken to investigate the benefit of the possible use of quantum cascade lasers (QCLs) in standoff explosives detection equipment. Standoff detection of explosives is currently one of the most difficult problems facing the explosives detection community. Increased domestic and troop security could be achieved through the remote detection of explosives. An effective remote or standoff explosives detection capability would save lives and prevent losses of mission-critical resources by increasing the distance between the explosives and the intended targets and/or security forces. Many sectors of the US government are urgently attempting to obtain useful equipment to deploy to our troops currently serving in hostile environments. This LDRD was undertaken to investigate the potential benefits of utilizing quantum cascade lasers (QCLs) in standoff detection systems. This report documents the potential opportunities that Sandia National Laboratories can contribute to the field of QCL development. The following is a list of areas where SNL can contribute: (1) Determine optimal wavelengths for standoff explosives detection utilizing QCLs; (2) Optimize the photon collection and detection efficiency of a detection system for optical spectroscopy; (3) Develop QCLs with broader wavelength tunability (current technology is a 10% change in wavelength) while maintaining high efficiency; (4) Perform system engineering in the design of a complete detection system and not just the laser head; and (5) Perform real-world testing with explosive materials with commercial prototype detection systems.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Investigation on the explosion dynamics of large-format lithium-ion pouch cells

Explosion is the most extreme case of thermal runaway of lithium-ion (Li-ion) batteries. In this study, explosion dynamics of large-format Li-ion cells are investigated experimentally and numerically. Overcharge-to-explosion tests are conducted on 40 Ah Li-ion cells with Li[Ni 0.8 Co 0.1 Mn 0.1 ]O 2 cathode. Based on the explosion physics, shockwave and detonation models are used to characterize the shock effect of the cell explosion and evaluate the explosion equivalent. Von Neumann peak is observed on the pressure curves, and the shockwave velocity is supersonic at this time; the unwrinkled spherical flame phenomenon observed in the experiment indicates that it is detonation. Additionally, a geometric model is established based on the real testing scenario, and the explosion behavior is numerically studied. The characteristics of the explosion dynamics process are interpreted and the propagation mechanism of the shockwave are revealed; the deflagration to detonation transition (DDT) phenomenon in this process is caused by the formation of “hot spots”, and the explosion of the cells eventually turns into stable combustion. Here this study fills the gap in the research on thermal runaway of Li-ion cells, especially in the extreme cases of fire and explosion, and provide useful guidance for battery safety.

42 ENGINEERING↗

Exploring the Effects of Emplacement Conditions on Explosion P/S Ratios across Local to Regional Distances

High-frequency (~> 2 Hz) seismic P/S amplitude ratios are well-established as a discriminant to distinguish between natural earthquakes and underground explosions at regional distances (~200–1500 km). As research shifts toward identifying lower-yield events, work has begun to investigate the potential of this discriminant for use at local distances (<200 km), in which initial results raise questions about its effectiveness. Here, we utilize data from several chemical explosion experiment series at the Nevada National Security Site in southern Nevada in the United States to study explosion Pg/Lg ratios across the range of local to regional distances. Additionall, the experiments are conducted over differing emplacement conditions, with contrasting geologies and a variety of yields and depths of burial, including surface explosions. We first establish the similarities of Pg/Lg ratios from chemical explosions to those from historic nuclear tests and conclude that, as previous data have suggested, chemical explosion ratios are good proxies for nuclear tests. We then examine Pg/Lg ratios from the new experiment series as functions of distance, yield, depth of burial, and scaled depth of burial (SDOB). At far-local and regional distances, we observe consistently higher ratios from hard-rock explosions compared to ones in a weaker dry alluvium medium, consistent with prior regional distance results. No other trends with yield, depth of burial, or SDOB are strongly evident. Scatter in the observed ratios is very high, particularly at the shortest event-to-station distances, suggesting that small-scale path effects play a significant role. On average, the local distance explosion Pg/Lg ratios show remarkable consistency across all the variations in emplacement. Explosion source models will need to reproduce these results.

58 GEOSCIENCES↗

Mafic explosive volcanism at Llaima Volcano: 3D x-ray microtomography reconstruction of pyroclasts to constrain shallow conduit processes

Abstract Mafic volcanic activity is dominated by effusive to mildly explosive eruptions. Plinian and ignimbrite-forming mafic eruptions, while rare, are also possible; however, the conditions that promote such explosivity are still being explored. Eruption style is determined by the ability of gas to escape as magma ascends, which tends to be easier in low-viscosity, mafic magmas. If magma permeability is sufficiently high to reduce bubble overpressure during ascent, volatiles may escape from the magma, inhibiting violent explosive activity. In contrast, if the permeability is sufficiently low to retain the gas phase within the magma during ascent, bubble overpressure may drive magma fragmentation. Rapid ascent may induce disequilibrium crystallization, increasing viscosity and affecting the bubble network with consequences for permeability, and hence, explosivity. To explore the conditions that promote strongly explosive mafic volcanism, we combine microlite textural analyses with synchrotron x-ray computed microtomography of 10 pyroclasts from the 12.6 ka mafic Curacautín Ignimbrite (Llaima Volcano, Chile). We quantify microlite crystal size distributions (CSD), microlite number densities, porosity, bubble interconnectivity, bubble number density, and geometrical properties of the porous media to investigate the role of magma degassing processes at mafic explosive eruptions. We use an analytical technique to estimate permeability and tortuosity by combing the Kozeny-Carman relationship, tortuosity factor, and pyroclast vesicle textures. The groundmass of our samples is composed of up to 44% plagioclase microlites, > 85% of which are < 10 µm in length. In addition, we identify two populations of vesicles in our samples: (1) a convoluted interconnected vesicle network produced by extensive coalescence of smaller vesicles (> 99% of pore volume), and (2) a population of very small and completely isolated vesicles (< 1% of porosity). Computed permeability ranges from 3.0 × 10 −13 to 6.3 × 10 −12 m 2 , which are lower than the similarly explosive mafic eruptions of Tarawera (1886; New Zealand) and Etna (112 BC; Italy). The combination of our CSDs, microlite number densities, and 3D vesicle textures evidence rapid ascent that induced high disequilibrium conditions, promoting rapid syn-eruptive crystallization of microlites within the shallow conduit. We interpret that microlite crystallization increased viscosity while simultaneously forcing bubbles to deform as they grew together, resulting in the permeable by highly tortuous network of vesicles. Using the bubble number densities for the isolated vesicles (0.1-3 −3 × 10 4 bubbles per mm 3 ), we obtain a minimum average decompression rate of 1.4 MPa/s. Despite the textural evidence that the Curacautín magma reached the percolation threshold, we propose that rapid ascent suppressed outgassing and increased bubble overpressures, leading to explosive fragmentation. Further, using the porosity and permeability of our samples, we estimated that a bubble overpressure > 5 MPa could have been sufficient to fragment the Curacautín magma. Other mafic explosive eruptions report similar disequilibrium conditions induced by rapid ascent rate, implying that syn-eruptive disequilibrium conditions may control the explosivity of mafic eruptions more generally.

Valdivia, Pedro↗

Categorizing An Explosive Device by its Nuclear Signature (Rev. 1)

This report documents a study to eliminate ambiguity in identifying a very low-yield nuclear detonation in the early stages of the response to such an event. The ambiguity arises from the very similar explosive and radiation effects produced by three categories of explosive devices: An explosively driven radiological dispersal device (RDD) or an accidental explosion in which radiologic material is scattered by chemical explosives. A failed nuclear device in which nuclear material, such as uranium or plutonium, has been scattered by conventional explosives. A nuclear device that, in addition to scattering nuclear material, produced a very low-yield from nuclear fission. The study found that the properties of fission products provide a ready solution to the problem. The radiation dose rate from fission products that were produced in a nearly instantaneous “fission event” decreases extremely rapidly over the first eight hours after that event, whereas nuclear materials and common radiological materials produce an essentially constant dose rate. This contrast provides an unequivocal fission product signature. The measurements required to utilize this signature can be made by first responders with radiation detectors already in the field, on time scales of an hour, although later confirmation using more capable detectors, including spectroscopic capability, is advised. The process of categorizing an explosives-related incident, both pre- and post-detonation, can be represented as a Decision Tree. The Decision Tree illustrates the use of already-fielded radiation detectors to categorize incidents as likely to involve only conventional explosives, an explosively driven RDD, or a nuclear device. The identification of an explosion as a fission event is extremely important to evacuation planners. It has been shown that delayed evacuation after sheltering in place for up to 24 hours after a fission event has the potential to reduce radiation exposure to the affected public and responders by a factor of ten. Traditional evidence collection after a nuclear detonation is likely to be similarly delayed, as the value and urgency of collection efforts must be weighed against radiation and other hazardous exposure of the collectors. The evidence that survives the immediate effects of a nuclear detonation will, in many cases, still be available for collection once radiation levels have diminished to acceptable levels. Certain classes of evidence, notably information stored on digital media, may significantly degrade from exposure to post-detonation radiation fields. Technical nuclear forensics collections will be performed in all events with nuclear yield. Modification of the high-yield collection strategy may be necessary for a very low-yield device.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗