Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EROSION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Effect of Sulfide Concentration on the Corrosion and Cavitation Erosion Behavior of a Manganese-Aluminum Bronze in 3.5% NaCl Solution

The effect of sulfide concentration on the corrosion and cavitation erosion behavior of a cast manganese-aluminum bronze (MAB) alloy in 3.5% NaCl solution was investigated. The electrochemical results showed that when the sulfide concentration exceeded 50 ppm, hydrogen evolution reaction dominated the cathodic process because of the very negative corrosion potential of MAB, and the formation of a copper sulfide film on MAB was a diffusion-controlled process. The mass loss rate of MAB after longer-term immersion was ordered by the sulfide concentration as: 20/50 ppm > 100 ppm > zero > 200 ppm. In the 200 ppm sulfide solution, the mass loss rate of MAB was the lowest, because of the formation of a thin and homogeneous copper sulfide film. In the other sulfide solutions, the formation of a less-protective film with both oxides and sulfides resulted in higher mass loss rate of MAB. Moreover, selective phase corrosion occurred at the β and κ phases in solutions with sulfide addition less than 100 ppm. For all solutions, it was the mechanical attack that dominated cavitation erosion degradation. The cavitation erosion–corrosion synergy was lower in high sulfide solutions, because the corrosion products on MAB could reduce the mechanical impact under cavitation erosion.

36 MATERIALS SCIENCE↗

Accurate modeling and reconstruction of three-dimensional percolating filamentary microstructures from two-dimensional micrographs via dilation-erosion method

Heterogeneous materials are ubiquitous in nature and synthetic situations and have a wide range of important engineering applications. Accurate modeling and reconstructing three-dimensional (3D) microstructure of topologically complex materials from limited morphological information such as a two-dimensional (2D) micrograph is crucial to the assessment and prediction of effective material properties and performance under extreme conditions. Here, we extend a recently developed dilation–erosion method and employ the Yeong–Torquato stochastic reconstruction procedure to model and generate 3D austenitic–ferritic cast duplex stainless steel microstructure containing percolating filamentary ferrite phase from 2D optical micrographs of the material sample. Specifically, the ferrite phase is dilated to produce a modified target 2D microstructure and the resulting 3D reconstruction is eroded to recover the percolating ferrite filaments. The dilation–erosion reconstruction is compared with the actual 3D microstructure, obtained from serial sectioning (polishing), as well as the standard stochastic reconstructions incorporating topological connectedness information. The fact that the former can achieve the same level of accuracy as the latter suggests that the dilation–erosion procedure is tantamount to incorporating appreciably more topological and geometrical information into the reconstruction while being much more computationally efficient. - Highlights: • Spatial correlation functions used to characterize filamentary ferrite phase • Clustering information assessed from 3D experimental structure via serial sectioning • Stochastic reconstruction used to generate 3D virtual structure 2D micrograph • Dilation–erosion method to improve accuracy of 3D reconstruction.

36 MATERIALS SCIENCE↗

Erosion processes due to energetic particle-surface interaction

The interaction of the fast particles from the hot plasma of a magnetic confinement fusion experiment with the first wall is one of the most challenging problems toward the realization of a fusion power plant. The erosion of the first wall by the fast particles leads to life time limitations and the radiative cooling of the plasma by the eroded impurity species lowers the energy confinement. Apart from these obvious consequences also the trapping of large quantities of the fuelling species (deuterium and tritium) in re-deposited layers of the eroded species poses a problem due to accumulation of large radiative inventories and plasma fuelling inefficiency. The source of all these challenges is the erosion of first wall components due to physical sputtering, chemical erosion and radiation enhanced sublimation. This paper will give an overview about the physical principles behind these erosion channels.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Nonlinear Impact of Edge Localized Modes on Carbon Erosion in the Divertor of the JET Tokamak

The impact of edge localized modes (ELMs) carrying energies of up to 450 kJ on carbon erosion in the JET inner divertor is assessed by means of time resolved measurements using an in situ quartz microbalance diagnostic. The inner target erosion is strongly nonlinearly dependent on the ELM energy: a single 400 kJ ELM produces the same carbon erosion as ten 150 kJ events. The ELM-induced enhanced erosion is attributed to the presence of codeposited carbon-deuterium layers on the inner divertor target, which are thermally decomposed under the impact of ELMs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Erosion Resistance Index (ERI) to Assess Surface Stability in Desert Environments

A new spectral index—erosion resistance index (ERI)—was developed to assess erosion risks in desert landscapes. The index was developed by applying trigonometry to the combination of the green/red band-ratio and the red/near infrared band-ratio from very high spatial resolution imagery. The resultant ERI maps showed spatially cohesive distributions of high and low index values across the study areas. High index values were observed over areas that were resistant to erosion (such as desert pavement and dense vegetation), while low index values overlapped with areas likely dominated by loose sandy soils, such as stream beds and access roads. Although further investigation is warranted, this new index, ERI, shows promise for the assessment of erosion risks in desert regions.

47 OTHER INSTRUMENTATION↗

Global meta-analysis of published river bank erosion and migration rates

This dataset is a compilation of 993 measurements of riverbank erosion or migration rates from 336 rivers and streams compiled from 169 published English language studies. The dataset spans rivers across latitudes ranging from 46 deg south to 71 deg north. The rivers range in drainage area from 0.6 to 3 million square kilometers. If provided in a published study, recorded channel width, river drainage area, and sediment load and/or yield were summarized. In the absence of these ancillary data from the original source, this data was compiled from other published studies, global and regional datasets, or measured from Google Earth images. The dataset also provides information on whether the rates were measured at an individual river bend or represent reach-based averages, as well as, whether the river is single or multi-threaded.Revisions 2023 January updateAdded 72 new erosion measurements. Dropped 10 records that did not have mean erosion values.“DrainageArea(km^2)_rabpro” added“DrainageArea(km^2)” – updated to only include published drainage area and values obtained from sources other than the rabpro analysis.“River_slope_pub” added to provide river slope values provided in the published erosion study or other source listed in the “Slope Reference” field“RiverSlope_Lin” added“FLO1K_MonthlyMax_LT” and “FLO1K_MontlyMax_PoR” added“KG_Zone” added from Köppen-geiger climate classification based on Beck et al. 2018

54 ENVIRONMENTAL SCIENCES↗

SimPLE.ca: Simulator of Productivity Loss due to Erosion for Canada

Robust and practical estimates of the impact of soil erosion on crop productivity are essential for developing and implementing appropriate solutions for soil erosion on agricultural land. The objective of this study was to develop a simple model which captured the most important relationships between topsoil erosion and productivity loss for major agricultural regions of Canada. The model was developed for spring wheat (Triticum aestivum L.) and corn (Zea mays L.). Using annual time steps, maximum crop yields were reduced by soil erosion due to losses in available water-holding capacity, N-mineralization potential and available P. Using minimal input data, the model accounted for 56% of the variation in relative yields (fraction of non-eroded controls) determined in field studies using desurfacing or comparison plot methods.

54 ENVIRONMENTAL SCIENCES↗

Initial observations of cavitation-induced erosion of liquid metal spallation target vessels at the Spallation Neutron Source

During operation of the Spallation Neutron Source (SNS) at Oak Ridge National Laboratory the mechanical properties of the AISI 316L target module are altered by high-energy neutron and proton radiation. The interior surfaces of the target vessel are also damaged by cavitation-induced erosion, which results from repetitive rapid heating of the liquid mercury by high-energy proton beam pulses. Until recently no observations of cavitation-induced erosion were possible for conditions prototypical to the SNS. Post irradiation examination (PIE) of the first and second operational SNS targets was performed to gain insight into the radiation-induced changes in mechanical properties of the 316L target material and the extent of cavitation-induced erosion to the target vessel inner surfaces. Observations of cavitation-induced erosion of the first and second operational SNS target modules are presented here, including images of the target vessel interiors and specimens removed from the target beam-entrance regions.

cavitation↗

Assessment of Soil Moisture and Fixatives Performance in Controlling Wind Erosion of Contaminated Soil at the Hanford Site

During the remediation of burial grounds at the US Department of Energy's (DOE's) Hanford Site in Washington State, the dispersion of contaminated soil particles and dust is an issue that is faced by site workers on a daily basis. This contamination issue is even more of a concern when one takes into account the semi-arid characteristics of the region where the site is located. To mitigate this problem, workers at the site use a variety of engineered methods to minimize the dispersion of contaminated soil and dust particles. Once such methods is the use of water and/or suppression agents (fixatives) that stabilizes the soil prior to soil excavation, segregation, and removal activities. A primary contributor to the dispersion of contaminated soil and dust is wind soil erosion. The erosion process occurs when the wind speed exceeds a certain threshold value (threshold shear velocity), which depends on a number of factors including wind force loading, particle size, surface soil moisture, and the geometry of the soil. Thus under these circumstances the mobility of contaminated soil and generation and dispersion of particulate matter are significantly influenced by these parameters. Wind tunnel experiments were conducted at the Florida International University's Applied Research Center (FIU-ARC) to evaluate the effectiveness of three commercially available fixatives in controlling the mobility of soil particles on soil mounds when exposed to varying wind forces. The fixatives tested included: (1) a calcium chloride solution; (2) a petroleum hydrocarbon emulsion; and 3) a synthetic organic. As an initial step, approximately 500 lbs of uncontaminated soil was obtained from the Hanford Reservation in Washington State. Soil samples were placed in an open-loop, low speed wind tunnel and exposed to wind forces ranging from 10 to 30 miles per hour (mph). Wind erosion controlling capabilities of commercially available fixatives and soil moisture were tested at a laboratory scale. Soil samples with varying moisture (W/W %) content and soil samples treated with fixatives, selected from a wide range of commercially available products, were exposed to a wind speeds ranging from 10 - 30 miles per hour (MPH). During these experiments, amount of soil displaced due to the wind forces, the amount of airborne particulates generated, and the moisture loss were measured to better understand the performance of selected fixatives and soil moisture. Results obtained during the study showed that there is a significant reduction in wind erosion and airborne particles generation by increasing the soil moisture for the velocities tested. Similar trend was observed when the soil samples treated with fixatives were exposed to the same range of velocities (10 - 30 MPH). (authors)

54 ENVIRONMENTAL SCIENCES↗

Erosion and Mobilisation of Highly Active Simulant Suspensions using Impinging Vertical Jets - 19378

Based on the nuclear industry in the U.K., storage of nuclear waste poses a particularly complex challenge. Specifically, this research is concerned with post-PUREX (Plutonium Uranium Redox Extraction) high level waste, known as HAL (Highly Active Liquor), containing nitric acid and a host of fission products. HAL is concentrated, and stored in HASTs (Highly Active Storage Tanks) at the HALES (Highly Active Liquor Evaporation and Storage) facility at the Sellafield site, UK. HASTs are large concrete containers designed to keep the HAL cool and continually circulated prior to vitrification for permanent storage and disposal. Without comprehensive understanding of how this HAL is behaving within the HASTs, a multitude of issues could arise, and understanding such issues is the basis of this research. Components of the HAL begin to form solid particles in the HASTS, and impinging vertical liquid jets are used to mobilize the sedimented particle bed to reduce hot-spot formation. Experimental validation of the jets and associated modelling is required to assess the jets efficacy, and by considering the erosion based on dimensionless parameters, will allow the results to be scaled. This is of particular interest due to the wide reaching applications to all industries that require utilisation of impinging jets, for mass or heat transfer. An experimental rig of 0.5 m{sup 3} has been used to experimentally model the central jet of the HASTs. A spherical glass simulant (SiO{sub 2}, spherical) of various sizes has been used for the initial non-cohesive particle testing, and modelling. Each experiment used 8 different jet diameters. Dimensionless analysis takes the form of the erosion parameter, Ec, which allows comparison of systems of different scales and a means of correlating multiple simulants against one another, so patterns are easily identifiable. Part of the dimensionless analysis was also to deduce the modified Shields parameter from vane viscometry to allow for a comparison of erosion behaviour taking into account particle properties, flow properties and the overall influence these have on the erosion profile. Particle size distribution was found to have a direct effect on yield stress and modified Shields parameter, with larger particles being dominated by inertial forces and past a certain size threshold surface forces appear to dominate. Ec data found the larger glass simulants to behave as expected for a non-cohesive particles, however surface forces also appear to be present for the smaller size distributions. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Hurricanes alter 10 Be concentrations in tropical river sediment but do not change regional erosion rate estimates

Tropical islands, including many in island arcs, are subjected to recurring disturbances from extreme storms such as tropical cyclones. To test whether such storms influence cosmogenic nuclide concentrations such that they do not reflect long-term rates of erosion, we measured meteoric and in situ 10Be in river sediment samples from Dominica, an andesitic island in the Caribbean, before and after category five Hurricane Maria (2017). Populations of before- and after-storm concentrations are statistically indistinguishable (n=7 pairs for in situ 10 Be, n=11 pairs for meteoric 10 Be). 10 Be concentrations vary from -138% to +73% within before-after sample pairs relative to the mean of the pair. These new data suggest that the effects of extreme storms on the depth and amount of near-surface erosion on Dominica vary spatially. Our data support calculations of Niemi, et al. (2005) and Yanites, et al. (2009) suggesting that basin-by-basin comparisons of erosion rates based on cosmogenic nuclides should be approached with caution in small (<~100 km 2 ) watersheds affected by mass movements and extreme storms. Erosion rates determined from in situ 10Be in Dominica (geometric mean=0.102 mm y-1, n=12) are low compared to similarly steep and wet areas globally and correlate positively with the spatial density of mass movements.

58 GEOSCIENCES↗

Localised instability of titanium during its erosion-corrosion in simulated acidic hydrometallurgical slurries

Electrochemical techniques were used to investigate the erosion-corrosion of titanium in simulated acidic mineral leaching slurries. Erosion-corrosion of titanium was caused by solid particle impingement. Electrochemical noise revealed that solid particle impacts resulted in localised fracture of the passive film, and erosion-corrosion of titanium proceeded in the form of current transients. As conditions become more abrasive, erosion-corrosion is an increasing threat to titanium equipment exposed to acidic slurries.

36 MATERIALS SCIENCE↗

Preliminary Evaluation of Cavitation-Erosion Resistance of Ti-Alloys in Mercury for the Spallation Neutron Source

A number of Ti-based alloys in both the mill-annealed and 20% cold-worked conditions were subjected to sonication conditions in Hg using a vibratory horn to assess relative cavitation-erosion resistance. Weight loss as a function of exposure time was roughly proportional to hardness for all alloys/conditions examined, with Ti-6Al-4V (Ti-Grade 5) and Ti-6Al-2Sn-4Zr-2Mo yielding the best resistance to cavitation-erosion as evidenced by low weight losses and little or no tendency to form pits on the exposed surface. Unalloyed Ti (Ti-Grade 4) and Ti-0.12Pd (Ti-Grade 7) exhibited greater weight losses by a factor or about two and about five, respectively, with Ti-0.12Pd particularly prone to pitting development. The mean erosion rates of the best two Ti-alloys examined here were about a factor of three higher than identically tested 316LN stainless steel following a low temperature carburizing treatment, but this difference is considered minor given that the rate for both materials is very low/manageable and represents a through-thickness property for the Ti-alloys. A nitriding surface treatment was also evaluated as a potential method to further increase the cavitation-erosion resistance of these alloys in Hg, but the selected treatment proved largely ineffective. Recommendations for further work to evaluate the efficacy of Ti-based alloys for use in high-powered targets for the Spallation Neutron Source are given.

36 MATERIALS SCIENCE↗

Surface erosion and modification by energetic ions.

Surface erosion and modification by energetic highly charged and cluster ions are important in the development of semiconductor devices, TeV accelerators, fission and fusion reactors, and in the development of extreme ultra-violet lithography devices. Gas cluster ion beam (GCIB) surface treatment can significantly mitigate the high-gradient electric vacuum breakdown of rf-cavities. GCIB can also mitigate Q-slope drop in superconducting Nb-cavities. Various mechanisms of the highly charged ion (HCI) energy transfer into the solid target, such as hollow atom formation, charge screening and neutralization, shock wave generation, and sputtering were analyzed. Surface erosions caused by GCIB, HCI bombardments, and by low energy He+ and H+ ions typical for fission and fusion devices were studied by using molecular dynamics simulation. A He bubble splashing mechanism of liquid Li containing was developed, and surface erosion was simulated. The mechanism of bubble explosion could significantly contribute to the surface erosion at high ion fluxes and explain the existing experimental results.

43 PARTICLE ACCELERATORS↗

The erosion of biodiversity and biomass in the Atlantic Forest biodiversity hotspot

Tropical forests are being deforested worldwide, and the remaining fragments are suffering from biomass and biodiversity erosion. Quantifying this erosion is challenging because ground data on tropical biodiversity and biomass are often sparse. Here, we use an unprecedented dataset of 1819 field surveys covering the entire Atlantic Forest biodiversity hotspot. We show that 83-85% of the surveys presented losses in forest biomass and tree species richness, functional traits, and conservation value. On average, forest fragments have 25-32% less biomass, 23-31% fewer species, and 33, 36, and 42% fewer individuals of late-successional, large-seeded, and endemic species, respectively. Biodiversity and biomass erosion are lower inside strictly protected conservation units, particularly in large ones. We estimate that biomass erosion across the Atlantic Forest remnants is equivalent to the loss of 55-70 thousand km 2 of forests or US$2.3-2.6 billion in carbon credits. These figures have direct implications on mechanisms of climate change mitigation.

54 ENVIRONMENTAL SCIENCES↗

A digital holography ex situ measurement characterization of plasma-exposed surface erosion from an electrothermal arc source

Digital holography has been proposed to fulfill a need for an imaging diagnostic capable of in situ monitoring of surface erosion caused by plasma–material interaction in nuclear fusion devices. A digital holography diagnostic for 3D surface erosion measurement has been developed at Oak Ridge National Laboratory with the goal of deployment on a plasma device. A proof-of-concept in situ demonstration is planned which would involve measurement of plasma erosion on targets exposed to an electrothermal arc source. This work presents the results of an ex situ characterization of the capability and limitations of holographic imaging of targets exposed to the arc source. Targets were designed to provide a fiducial for comparison of deformed and unaffected areas. The results indicated that the average net erosion was ~150 nm/plasma exposure, which is expected to be within the diagnostic’s measurement capacity. Surface roughness averages determined by holographic image analysis showed good agreement with measurements taken with a profilometer. Finally, the limit of the holography diagnostic’s x–y spatial resolution was characterized by comparison with scanning electron microscope imaging.

47 OTHER INSTRUMENTATION↗

Erosion rates of diffuse and constricted magnetron discharges in helium over aluminium, gallium, molybdenum, and tantalum

Magnetically-enhanced discharge plasmas in light monatomic gases such as helium may have applicability in future electric power grid switches. For practical use of a gas discharge switch in power conversion the net cathode erosion rate must be sufficiently low to enable stable operation over an extended life. We have found that magnetically-enhanced He plasmas at pressures of 200–800 mTorr can operate in one of several distinct modes that are characterized by the plasma geometry (diffuse, constricted) and motion (stationary, orbiting, slow). The erosion rates of various cathode materials (aluminium, gallium, molybdenum, and tantalum) were measured in both diffuse and constricted, magnetized He plasmas. The constricted orbiting (CO) mode exhibited a lower erosion rate than either the diffuse stationary or constricted slow modes, even when comparing loss rates against a cathode material that was more liable to sputter (e.g. aluminium versus molybdenum). However, the erosion rate for operation in the CO mode was still found to be significantly higher than required for practical use in a gas discharge switch.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Nonlinear impact of the porous nanostructure on the net tungsten erosion in the linear plasma device PISCES-A

Abstract The tungsten fuzz growth under non-erosive and erosive helium plasmas in the linear plasma device PISCES-A has been investigated by experiments and simulations. The simulation results benchmarked against the experimental measurements indicate a decayed net physical sputtering yield during fuzz growth under the erosive helium plasma. Further, a nonlinear dependence of the net tungsten erosion on the ‘effective’ porous nanostructure that can be sputtered by incident helium particles has been found.

Physics↗