Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELEVATION ANGLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Microwave Propagation Attenuation due to Earth's Atmosphere and Weather at SHF Band

In this study we have estimated radio wave propagation losses at super high frequency (SHF) band by applying available propagation models into several Air Force benchmark scenarios. The study shows that dominantly additional losses over the free space loss are atmospheric absorption, clouds, fog, and precipitation, as well as scintillation /multipath at low elevation angles. The free space loss equation has been modified to include all atmospheric attenuation and fading effects that cannot be neglected over the range of frequency of interest. Terrain profiles along all directions of interest within the coastal areas and inland areas for four benchmark cases have been analyzed in detail. We find that while the atmospheric gaseous absorption plays a significant role under a clear weather, heavy rainfalls can cause several tens of dB loss for a 100- km path through the rain. At very low elevation angles (< 5 deg), atmospheric scintillation/multipath fading becomes a very important factor. There are significant differences in the feature of anomalous mode (ducting) propagation between the east and the west coastal receiving stations.

atmospheric absorption↗
NASA NTRS1988

Vehicle antenna for the mobile satellite experiment

A low profile, low cost, printed circuit, electronically steered, right hand circularly polarized phase array antenna system has been developed for the Mobile Satellite Experiment (MSAT-X) Program. The success of this antenna is based upon the development of a crossed-slot element array and detailed trade-off analyses for both the phased array and pointing system design. The optimized system provides higher gain at low elevation angles (20 degrees above the horizon) and broader frequency coverage (approximately 8 1/2 percent bandwidth) than is possible with a patch array. Detailed analysis showed that optimum performance could be achieved with a 19 element array of a triangular lattice geometry of 3.9 inch element spacing. This configuration has the effect of minimizing grating lobes at large scan angles plus it improves the intersatellite isolation. The array has an aperture 20 inches in diameter and is 0.75 inch thick overall, exclusive of the RF and power connector. The pointing system employs a hybrid approach that operates with both an external rate sensor and an internal error signal as a means of fine tuning the beam acquisition and track. Steering the beam is done electronically via 18, 3-bit diode phase shifters. A nineteenth phase shifter is not required as the center element serves as a reference only. Measured patterns and gain show that the array meets the stipulated performance specifications everywhere except at some low elevation angles.

Peng, Sheng Y.↗
NASA NTRS2015

Construction of Polarimetric Radar-Based Reference Rain Maps for the Iowa Flood Studies Campaign

The Global Precipitation Measurement (GPM) Mission Iowa Flood Studies (IFloodS) campaign was conducted in central and northeastern Iowa during the months of April-June, 2013. Specific science objectives for IFloodS included quantification of uncertainties in satellite and ground-based estimates of precipitation, 4-D characterization of precipitation physical processes and associated parameters (e.g., size distributions, water contents, types, structure etc.), assessment of the impact of precipitation estimation uncertainty and physical processes on hydrologic predictive skill, and refinement of field observations and data analysis approaches as they pertain to future GPM integrated hydrologic validation and related field studies. In addition to field campaign archival of raw and processed satellite data (including precipitation products), key ground-based platforms such as the NASA NPOL S-band and D3R Ka/Ku-band dual-polarimetric radars, University of Iowa X-band dual-polarimetric radars, a large network of paired rain gauge platforms, and a large network of 2D Video and Parsivel disdrometers were deployed. In something of a canonical approach, the radar (NPOL in particular), gauge and disdrometer observational assets were deployed to create a consistent high-quality distributed (time and space sampling) radar-based ground "reference" rainfall dataset, with known uncertainties, that could be used for assessing the satellite-based precipitation products at a range of space/time scales. Subsequently, the impact of uncertainties in the satellite products could be evaluated relative to the ground-benchmark in coupled weather, land-surface and distributed hydrologic modeling frameworks as related to flood prediction. Relative to establishing the ground-based "benchmark", numerous avenues were pursued in the making and verification of IFloodS "reference" dual-polarimetric radar-based rain maps, and this study documents the process and results as they pertain specifically to efforts using the NPOL radar dataset. The initial portions of the "process" involved dual-polarimetric quality control procedures which employed standard phase and correlation-based approaches to removal of clutter and non-meteorological echo. Calculation of a scale-adaptive KDP was accomplished using the method of Wang and Chandrasekar (2009; J. Atmos. Oceanic Tech.). A dual-polarimetric blockage algorithm based on Lang et al. (2009; J. Atmos. Oceanic Tech.) was then implemented to correct radar reflectivity and differential reflectivity at low elevation angles. Next, hydrometeor identification algorithms were run to identify liquid and ice hydrometeors. After the quality control and data preparation steps were completed several different dual-polarimetric rain estimation algorithms were employed to estimate rainfall rates using rainfall scans collected approximately every two to three minutes throughout the campaign. These algorithms included a polarimetrically-tuned Z-R algorithm that adjusts for drop oscillations (via Bringi et al., 2004, J. Atmos. Oceanic Tech.), and several different hybrid polarimetric variable approaches, including one that made use of parameters tuned to IFloodS 2D Video Disdrometer measurements. Finally, a hybrid scan algorithm was designed to merge the rain rate estimates from multiple low level elevation angle scans (where blockages could not be appropriately corrected) in order to create individual low-level rain maps. Individual rain maps at each time step were subsequently accumulated over multiple time scales for comparison to gauge network data. The comparison results and overall error character depended strongly on rain event type, polarimetric estimator applied, and range from the radar. We will present the outcome of these comparisons and their impact on constructing composited "reference" rainfall maps at select time and space scales.

Radar↗
NASA NTRS1988

Ground plane interference elimination by passive element

The radiation pattern of a beam at elevation angles near the horizon is improved for phased array antennas by control of the radiation field intensity near the horizon to reduce multipath disturbances, and to improve the axial ratio of a circularly polarized phased array antenna. This is accomplished by placing a parasitic phase shifting element directly below the antenna beam axis. The waveguide section is designed to produce a phase shift in the portion of antenna radiation energy passing through it to cancel some of the radiation energy in the direction of the horizon. The spacing of the waveguide section in front of the antenna is determined empirically for optimum results, i.e., for reduction of beam power below about 20.degree. without affecting beam power at high elevation angles.

Bonebright, Mark E.↗
NASA NTRS2010

Homologous Deformation of the Effelsberg 100-m Telescope Determined with a Total Station

Due to gravitation the main reflector of the Effelsberg 100-m telescope of the Max Planck Institute for Radio Astronomy is deformed whenever it is tilted from zenith to arbitrary elevation angles. However, the resulting shape always is a paraboloid again, though with different parameters, a phenomenon which is called homologous deformation. In summer 2008, we have carried out measurements with a total station to determine the magnitude of these deformations in order to evaluate existing assumptions provided by the manufacturer from the telescope's design phase. The measurements are based on a newly developed approach with a Leica TCRP 1201 total station mounted head down near the subreflector. Mini-retro-reflectors are placed at various locations on the paraboloid itself and on the subreflector support structure. The results indicate that the measurement setup is suitable for the purpose and provides the information needed for a determination of elevation dependent delay corrections. The focal length changes only by about 8 mm when the telescope is tilted from 90. to 7.5. elevation angle.

Nothnagel, Axel↗
NASA NTRS1986

Ground plane interference elimination by passive element

The radiation pattern of a beam at elevation angles near the horizon is improved for phased array antennas by control of the radiation field intensity near the horizon to reduce multipath disturbances, and to improve the axial ratio of a circularly polarized phased array antenna. This is accomplished by placing a parasitic phase shifting element directly below the antenna beam axis. The waveguide section is designed to produce a phase shift in the portion of antenna radiation energy passing through it to cancel some of the radiation energy in the direction of the horizon. The spacing of the waveguide section in front of the antenna is determined empirically for optimum results, i.e., for reduction of beam power below about 20 deg. without affecting beam power at high elevation angles.

Bonebright, Mark E.↗
NASA NTRS1988

Measurement and modeling of land mobile satellite propagation at UHF and L-band

A propagation experiment is described in which a stratospheric balloon served as a transmitter platform at 870 and 1502 MHz in simulation of a land mobile satellite. A vehicle followed the drifting balloon along roads of western Texas and New Mexico, collecting at L-band amplitude and phase, and at UHF amplitude information only for elevation angles between 25 and 45 deg. The data obtained have been analyzed and are presented along with results from modeling of multipath scattering and roadside tree attenuation. The signal, with variations caused by multipath propagation and tree shadowing, was reduced by 3 dB at L-band and 2 dB at UHF for one percent of all locations. A median ratio of 3.9 was found between peak-to-peak phase (degrees) and power (dB) fluctuations. The ratio between L-band and UHF dB attenuation averages varied from 1.3 to 1.0 at fade levels from 6 to 23 dB. Optical sky brightness was measured and used to predict fade distribution with great accuracy. A single-scatterer multipath model is introduced. It is used to duplicate some of the measured data and to show the dependence of power variations on satellite elevation angle. Using Fresnel diffraction theory, the attenuation caused by a model tree was calculated to be near 10 dB and the maximum fade was found to increase by the logarithm of the number of branches.

Vogel, Wolfhard J.↗
NASA NTRS2016

Comparison of Atmospheric Delay Statistics from Deep Space Network Arrays and Nearby Test Interferometers

Several techniques have been explored and demonstrated that allow for greater data return on space-to-ground links. Among these techniques, arraying several smaller diameter dish antennas together is one method used in several arenas. These arrays can achieve larger effective area and gain than are available from a single larger antenna. This technique is routinely used by the NASA Deep Space Network (DSN) at 8.4 GHz where the incoming signals are much weaker than those experienced by the near-Earth satellite community. When considering arraying at much higher frequencies such as 32 GHz deep-space Ka-band, the phase alignment of the individual antenna signals is significantly disrupted by atmospheric turbulence. Since 2012, several downlink array demonstrations have been conducted using 32 GHz carrier signals emitted by the deep space probes Cassini and Kepler. Site test interferometers (STIs) that receive signals from geostationary satellites have been deployed at all three DSN tracking complexes for long-term monitoring of atmospheric delay fluctuations. In a previous DSN array demonstration study involving the Cassini spacecraft, it was shown that statistics of the adjusted STI phase fluctuations matched the statistics of concurrent array demonstration phase fluctuations. These adjustments accounted for differences in antenna separation, elevation angle and spacecraft frequencies. The STI antenna separations were about 200 m and the DSN antenna separations were about 300 m. These adjustments made use of the thick-layer turbulence model that was applicable to the Goldstone desert climate during the summer months for which the data were acquired. In this paper, we report on the results of additional array demonstrations involving the Kepler spacecraft and compare the adjusted STI phase fluctuations with those seen by a nearby two-element array of 34 m diameter antennas tracking Kepler’s 32 GHz signal at the Goldstone, California and Madrid, Spain DSN sites. We also discuss results from a demonstration using an array over a longer 12.5 km baseline. The Cassini and Kepler array demonstrations were found to validate the long term statistics acquired from several years of STI data as well as the models used to adjust the statistics for the conditions of an array. These statistics represent reliable estimates of the phase fluctuations that would be seen by an array tracking a deep space signal after applying appropriate adjustments for a given array configuration, elevation angle profile and observing frequency.

Morabito, David D.↗
NASA NTRS1934

Pressure-Distribution Measurements on the Hull and Fins of a 1/40-Scale Model of the U. S. Airship "Akron."

This report presents the results of measurements of pressure distribution conducted in the propeller-research wind tunnel of the National Advisory Committee for Aeronautics on a 1/40-scale model of the U. S. Airship "Akron" (ZRS-4). The pressures, which were measured simultaneously at nearly 400 orifices located at 26 stations along one side of the hull, were recorded by two photographic multiple manometers placed inside the model. The hull pressures were measured both with and without the tail surfaces and the control car for eight angles of pitch varying from 0 degree to 20 degrees and at air speeds of approximately 70 and 100 miles per hour. The pressures were also measured at approximately 160 orifices on one horizontal fin for the above speeds and pitch angles and for nine elevator angles.

Freeman, Hugh B↗
NASA NTRSDate not supplied

Monthly Mean DNI and GTI Derived from Monthly Mean GHI and DHI Using Two Methods: Comparisons with the BSRN Data and the Results Derived from the CERES Hourly Data

Monthly mean Global Horizontal Irradiances (GHI) and Diffuse Horizontal Irradiances (DHI) are more widely available than monthly mean Direct Normal Irradiances (DNI) and Global Tilted Irradiances (GTI). Empirical methods have been developed to derive monthly mean DNI and GTI from monthly mean GHI or from GHI and DHI. In this paper, we evaluate two such methods. The first one was the Whitlock Method developed by Charles H. Whitlock (2005) for the NASA POWER project by means of regression of the BSRN data. The method expresses the monthly mean DHI-to-GHI ratio as polynomial functions of monthly mean clearness index, sunset hour angle and noon solar elevation angle on the monthly-average-day. The monthly mean DNI is calculated by dividing the monthly mean GHI-DHI difference, or DirHI, by the cosine of the solar zenith angle at the mid-time between sunrise and solar noon on the monthly-average-day. The second method is the LJCR Method developed by Liu and Jorden (1960) and Collares-Pereira and Rabl (1979), and this method empirically splits monthly mean GHI and DHI into hourly means on the monthly-average-day, and the resulting hourly mean GHI and DHI and their difference, DirHI, can then be used to compute the monthly mean DNI, GTI and the global solar tracker irradiance (GTrI). This method is also used by RETScreen. We recently produced a set of hourly DNI and DHI by bias-correcting the CERES hourly DNI and DHI, and computed hourly GTI and GTrI as well. The data span twenty plus years from March 2000 to near present on a 1 by 1 grid system. The monthly mean CERES GHI and the corrected DHI are used as inputs to the above two methods to compute monthly mean DNI, GTI and GTrI. Through comparisons with the BSRN data, it is found that the Whitlock Method, with slight modification, and the LJCR Method can produce results that are nearly as good as the results derived from the CERES hourly data.

Taiping Zhang↗
NASA NTRS1974

Impact of combustion products from Space Shuttle launches on ambient air quality

The present work describes some multilayer diffusion models and a computer program for these models developed to predict the impact of ground clouds formed during Space Shuttle launches on ambient air quality. The diffusion models are based on the Gaussian plume equation for an instantaneous volume source. Cloud growth is estimated on the basis of measurable meteorological parameters: standard deviation of the wind azimuth angle, standard deviation of wind elevation angle, vertical wind-speed shear, vertical wind-direction shear, and depth of the surface mixing layer. Calculations using these models indicate that Space Shuttle launches under a variety of meteorological regimes at Kennedy Space Center and Vandenberg AFB are unlikely to endanger the exposure standards for HCl; similar results have been obtained for CO and Al2O3. However, the possibility that precipitation scavenging of the ground cloud might result in an acidic rain that could damage vegetation has not been investigated.

Dumbauld, R. K.↗
NASA NTRS1991

On optimal filtering of GPS dual frequency observations without using orbit information

The concept of optimal filtering of observations collected with a dual frequency GPS P-code receiver is investigated in comparison to an approach for C/A-code units. The filter presented here uses only data gathered between one receiver and one satellite. The estimated state vector consists of a one-way pseudorange, ionospheric influence, and ambiguity biases. Neither orbit information nor station information is required. The independently estimated biases are used to form double differences where, in case of a P-code receiver, the wide lane integer ambiguities are usually recovered successfully except when elevation angles are very small. An elevation dependent uncertainty for pseudorange measurements was discovered for different receiver types. An exponential model for the pseudorange uncertainty was used with success in the filter gain computations.

Eueler, Hans-Juergen↗
NASA NTRS1978

Effect of wind turbulence and shear on landing performance of jet transports

Computer simulations of a Boeing 727 class aircraft landing in turbulence were developed by programming the longitudinal aircraft equations of motion into a digital computer with various input values of vertical and horizontal wind speeds. Turbulent wind data was fed to the computer in one-second intervals. The computer computed in one-second intervals the aircraft speed, altitude, horizontal distance traveled, rate-of-descent, pitch attitude, glide path angle (from edge of runway) and elevator angle. All computer runs were made in the 'stick-fixed' mode. The RMS values of altitude and velocity perturbations (from equilibrium) were found to be large when horizontal wind gusts had sinusoidal components at or near the phugoid (long period) frequency. Maximum RMS altitude deviations occurred when the vertical wind had sinusoidal components which were 1/10 to 1/5 of the phugoid frequency. When real wind data (obtained from NCAR Queen Air) were used as input winds good correlations were found to exist between RMS velocity perturbations and both horizontal and vertical wind shears.

Blick, E. F.↗
NASA NTRS1976

The prediction of zenith range refraction from surface measurements of meteorological parameters

In the last two decades, increasingly sophisticated deep space missions have placed correspondingly stringent requirements on navigational accuracy. As part of the effort to increase navigational accuracy, and hence the quality of radiometric data, much effort has been expended in an attempt to understand and compute the tropospheric effect on range (and hence range rate) data. The general approach adopted has been that of computing a zenith range refraction, and then mapping this refraction to any arbitrary elevation angle via an empirically derived function of elevation. The prediction of zenith range refraction derived from surface measurements of meteorological parameters is presented. Refractivity is separated into wet (water vapor pressure) and dry (atmospheric pressure) components. The integration of dry refractivity is shown to be exact. Attempts to integrate wet refractivity directly prove ineffective; however, several empirical models developed by the author and other researchers at JPL are discussed. The best current wet refraction model is here considered to be a separate day/night model, which is proportional to surface water vapor pressure and inversely proportional to surface temperature. Methods are suggested that might improve the accuracy of the wet range refraction model.

Berman, A. L.↗
NASA NTRS1978

Measurements of constituents of interest in the photochemistry of the ozone layer using infrared techniques

Infrared solar spectra and infrared atmospheric emission spectra were obtained from the ground, from aircraft and from balloons. The initial detection of most stratospheric molecules was achieved by the solar spectral technique because better resolution helps remove interference from other molecules. Because the sun is an intense source of radiation, the resolution which can be obtained with good signal-to-noise, is greater than with atmospheric emission spectroscopy. Data are generally taken using a method that enhances the number of molecules in the optical path i.e. at large solar zenith angles for solar spectra and at low elevation angles for atmospheric emission spectra. The search for molecules which are predicted to be present but which, the detection of a molecule known to be present from other measurement techniques but observed for the first time in infrared solar spectra, and some further data on the variability of HNO3 are discussed.

Murcray, D. G.↗
NASA NTRS1952

Matrix Method of Determining the Longitudinal-Stability Coefficients and Frequency Response of an Aircraft from Transient Flight Data

A matrix method is presented for determining the longitudinal-stability coefficients and frequency response of an aircraft from arbitrary maneuvers. The method is devised so that it can be applied to time-history measurements of combinations of such simple quantities as angle of attack, pitching velocity, load factor, elevator angle, and hinge moment to obtain the over-all coefficients. Although the method has been devised primarily for the evaluation of stability coefficients which are of primary interest in most aircraft loads and stability studies, it can be used also, with a simple additional computation, to determine the frequency-response characteristics. The entire procedure can be applied or extended to other problems which can be expressed by linear differential equations.

Donegan, James J↗