Results for “Dynamic Procedures” — Page 7

NASA NTRSDate not supplied

An Efficient Approach to Collect Inlet Characterization Data

This report considers a novel process to acquire performance data for supersonic mixed compression inlets that is faster, and therefore less costly, than the previous one. In the previous process, measurements were recorded in discrete increments. The backpressuring actuator was advanced, there was a pause to allow for airflow fluctuations to diminish, and then the measurements were recorded. While this process was methodical, reliable and accurate, it consumed significant wind-on time. In general, high-speed wind tunnels are expensive to operate considering maintenance, energy and human resource requirements. Furthermore, many facilities, such as blowdown wind tunnels, are limited in the duration that they can maintain the desired test condition. Consequently, a quick method to collect the measurements is desired. A favored approach has the actuator moving in a continuous fashion with measurements recorded as the actuator continuously progresses through the increment points. This approach, identified as the dynamic inlet characteristic data acquisition procedure, uses in situ dynamic high-speed pressure sensors to measure pressure signals. While faster, continuous movement adds dynamic effects to the data. To better understand these dynamic effects and other potential influences, a study was undertaken to compare wind tunnel measurements taken at discrete actuator position points with data gathered during continuous actuator movement. Specially, plots of inlet pressure recovery versus mass capture ratio, or total pressure characteristic curves, were examined. The data were measured during experiments in the NASA Glenn Research Center Abe Silverstein 10- by 10-Foot Supersonic Wind Tunnel (SWT) with an inlet propulsion test article. In this report, the wind tunnel experiment and the study objectives are described. The processes to reduce the data and for analysis are explained. A discussion of the results along with features noted in the data is given. Finally, conclusions from this study that may be used to guide future wind tunnel experiment planning are presented.

Inlet↗

NASA NTRSDate not supplied

An Efficient Approach to Collect Inlet Characterization Data

This report considers a novel process to acquire performance data for supersonic mixed compression inlets that is faster, and therefore less costly, than the previous one. In the previous process, measurements were recorded in discrete increments. The backpressuring actuator was advanced, there was a pause to allow for airflow fluctuations to diminish, and then the measurements were recorded. While this process was methodical, reliable and accurate, it consumed significant wind-on time. In general, high-speed wind tunnels are expensive to operate considering maintenance, energy and human resource requirements. Furthermore, many facilities, such as blowdown wind tunnels, are limited in the duration that they can maintain the desired test condition. Consequently, a quick method to collect the measurements is desired. A favored approach has the actuator moving in a continuous fashion with measurements recorded as the actuator continuously progresses through the increment points. This approach, identified as the dynamic inlet characteristic data acquisition procedure, uses in situ dynamic high-speed pressure sensors to measure pressure signals. While faster, continuous movement adds dynamic effects to the data. To better understand these dynamic effects and other potential influences, a study was undertaken to compare wind tunnel measurements taken at discrete actuator position points with data gathered during continuous actuator movement. Specially, plots of inlet pressure recovery versus mass capture ratio, or total pressure characteristic curves, were examined. The data were measured during experiments in the NASA Glenn Research Center Abe Silverstein 10- by 10-Foot Supersonic Wind Tunnel (SWT) with an inlet propulsion test article. In this report, the wind tunnel experiment and the study objectives are described. The processes to reduce the data and for analysis are explained. A discussion of the results along with features noted in the data is given. Finally, conclusions from this study that may be used to guide future wind tunnel experiment planning are presented.

Data Acquisition↗

NASA NTRS2023

Anisotropic Mach Cone Aligned Mesh Adaptation for Low Boom Simulations

An automated off-body Mach cone aligned structured curvilinear grid generation procedure is presented for near-field computational fluid dynamics simulations. This procedure combines output-based indicators and mesh redistribution to perform anisotropic mesh adaptation while maintaining Mach cone alignment. Automation is achieved through a novel direction-based adaptation indicator formulation. The adaptation procedure is demonstrated on the JAXA Wing Body geometry and X-59 C608 demonstrator model from the Second and Third AIAA Sonic Boom Prediction Workshops, respectively. It is demonstrated that anisotropic mesh adaptation may result in a greater than fifty percent reduction in resource usage required to achieve the same level of accuracy as uniform and user constructed Mach cone aligned grids for near-field pressure signatures, ground-level overpressure signatures, and loudness metrics.

CST↗

NASA NTRS2023

Anisotropic Mach Cone Aligned Mesh Adaptation for Low Boom Simulations

An automated off-body Mach cone aligned structured curvilinear grid generation procedure is presented for near-field computational fluid dynamics simulations. This procedure combines output-based indicators and mesh redistribution to perform anisotropic mesh adaptation while maintaining Mach cone alignment. Automation is achieved through a novel direction-based adaptation indicator formulation. The adaptation procedure is demonstrated on the JAXA Wing Body geometry and X-59 C608 demonstrator model from the Second and Third AIAA Sonic Boom Prediction Workshops, respectively. It is demonstrated that anisotropic mesh adaptation may result in a greater than fifty percent reduction in resource usage required to achieve the same level of accuracy as uniform and user constructed Mach cone aligned grids for near-field pressure signatures, ground-level overpressure signatures, and loudness metrics.

CST↗

NASA NTRS1989

Dynamic Delamination Buckling In Composite Laminates

Procedure for mathematical modeling of dynamic delamination buckling and propagation of delamination, with plate bending elements and multipoint constraints, developed and incorporated into finite-element computer program. Predicts time at which delamination buckling occurs, shape of dynamic-buckling mode, and strain-energy-release rate due to extension of delamination crack. Method extended to handle such other defects as transply and edge cracks.

Grady, Joseph E.↗

NASA NTRS1989

Distribution of dynamic loads for multiple cooperating robot manipulators

For the situation of multiple cooperating manipulators handling a single object, a formulation is presented which allows load distribution of the combined system to be made while taking manipulator dynamics into account. First, object dynamics are used to transform the motion task. An integrated procedure for modeling arm dynamics are used to transform the motion task. An integrated procedure for modeling arm dynamics is detailed. Then, a method is introduced which transforms the object load to the joint level. At this level, various methods of load distribution that allow subtask performance are proposed. These methods allow desired object motion while selecting loads desirable to alleviate manipulator dynamic loads.

Walker, Ian D.↗

NASA NTRS1994

Mesh quality control for multiply-refined tetrahedral grids

A new algorithm for controlling the quality of multiply-refined tetrahedral meshes is presented in this paper. The basic dynamic mesh adaption procedure allows localized grid refinement and coarsening to efficiently capture aerodynamic flow features in computational fluid dynamics problems; however, repeated application of the procedure may significantly deteriorate the quality of the mesh. Results presented show the effectiveness of this mesh quality algorithm and its potential in the area of helicopter aerodynamics and acoustics.

Biswas, Rupak↗

NASA NTRS1992

Fully integrated aerodynamic/dynamic optimization of helicopter rotor blades

A fully integrated aerodynamic/dynamic optimization procedure is described for helicopter rotor blades. The procedure combines performance and dynamic analyses with a general purpose optimizer. The procedure minimizes a linear combination of power required (in hover, forward flight, and maneuver) and vibratory hub shear. The design variables include pretwist, taper initiation, taper ratio, root chord, blade stiffnesses, tuning masses, and tuning mass locations. Aerodynamic constraints consist of limits on power required in hover, forward flight and maneuvers; airfoil section stall; drag divergence Mach number; minimum tip chord; and trim. Dynamic constraints are on frequencies, minimum autorotational inertia, and maximum blade weight. The procedure is demonstrated for two cases. In the first case, the objective function involves power required (in hover, forward flight and maneuver) and dynamics. The second case involves only hover power and dynamics. The designs from the integrated procedure are compared with designs from a sequential optimization approach in which the blade is first optimized for performance and then for dynamics. In both cases, the integrated approach is superior.

Walsh, Joanne L.↗

NASA NTRS1992

Fully integrated aerodynamic/dynamic optimization of helicopter rotor blades

This paper describes a fully integrated aerodynamic/dynamic optimization procedure for helicopter rotor blades. The procedure combines performance and dynamics analyses with a general purpose optimizer. The procedure minimizes a linear combination of power required (in hover, forward flight, and maneuver) and vibratory hub shear. The design variables include pretwist, taper initiation, taper ratio, root chord, blade stiffnesses, tuning masses, and tuning mass locations. Aerodynamic constraints consist of limits on power required in hover, forward flight and maneuver; airfoil section stall; drag divergence Mach number; minimum tip chord; and trim. Dynamic constraints are on frequencies, minimum autorotational inertia, and maximum blade weight. The procedure is demonstrated for two cases. In the first case the objective function involves power required (in hover, forward flight, and maneuver) and dynamics. The second case involves only hover power and dynamics. The designs from the integrated procedure are compared with designs from a sequential optimization approach in which the blade is first optimized for performance and then for dynamics. In both cases, the integrated approach is superior.

Walsh, Joanne L.↗

NASA NTRS1989

Recursive Newton-Euler formulation of manipulator dynamics

A recursive Newton-Euler procedure is presented for the formulation and solution of manipulator dynamical equations. The procedure includes rotational and translational joints and a topological tree. This model was verified analytically using a planar two-link manipulator. Also, the model was tested numerically against the Walker-Orin model using the Shuttle Remote Manipulator System data. The hinge accelerations obtained from both models were identical. The computational requirements of the model vary linearly with the number of joints. The computational efficiency of this method exceeds that of Walker-Orin methods. This procedure may be viewed as a considerable generalization of Armstrong's method. A six-by-six formulation is adopted which enhances both the computational efficiency and simplicity of the model.

Nasser, M. G.↗

NASA NTRS1978

Dynamic simulation studies of fuel conservation procedures used in terminal areas

A simulation program was devised to study the effects of fuel conservation procedures on ATC and terminal area operations. The FAA National Aviation Facilities Experimental Center and the Ames Research Center have interconnected ATC and piloted simulation facilities at both centers. A unique national simulation facility for the study of pilot/controller/system interactions was established. The present paper describes the simulation facilities and outlines aircraft operational procedures evaluated in the experiments. Two experiments studied are discussed: the first involves two types of landing approaches, while the second involves both landing approaches and profile descents.

Obrien, P. J.↗

NASA NTRS1984

Dynamical phenomena in sunspots. I - Observing procedures and oscillatory phenomena. II - A moving magnetic feature

High resolution spectra consisting of at least 1 hr periods were obtained of the sunpost atmosphere. The Ca II H and K lines were scanned to characterize umbral oscillations and flashes. The former displayed peaks lasting 150-197 sec, while penumbral oscillations peaked in the 197-300 sec range. Quiet sun oscillations exhibited no peaks under 300 sec. The Ca II K line umbral flashes were ubiquitous for all observational periods and were associated with light bridges in the umbra. Magnetic field, vertical velocity, and chromospheric intensity measurements taken during the 1 hr scans covered moving magnetic features (MMF), which traversed the moats around sunspots. MMF areas increased while the magnetic field intensity decreased with MMF movement away from a sunspot. Bright Ca II K line wings were apparent in the MMFs, but cores of the lines were not observed, suggesting that flux loops generating the line are low in the photosphere.

Thomas, J. H.↗

NASA NTRS1993

Technique and applications of device driver dynamic loading

This paper discusses the techniques and feasibility of dynamically loading device drivers for the real-time operating system of the Space Station Freedom Data Management System. The rationale and advantages of device driver dynamic loading are discussed and the procedures are analyzed. A prototype program is implemented to demonstrate the feasibility and to simplify the procedure of device driver dynamic loading for the Space Station Freedom Program.

Liu, Yuan-Kwei↗

NASA NTRS1997

Design of Neural Networks for Fast Convergence and Accuracy: Dynamics and Control

A procedure for the design and training of artificial neural networks, used for rapid and efficient controls and dynamics design and analysis for flexible space systems, has been developed. Artificial neural networks are employed, such that once properly trained, they provide a means of evaluating the impact of design changes rapidly. Specifically, two-layer feedforward neural networks are designed to approximate the functional relationship between the component/spacecraft design changes and measures of its performance or nonlinear dynamics of the system/components. A training algorithm, based on statistical sampling theory, is presented, which guarantees that the trained networks provide a designer-specified degree of accuracy in mapping the functional relationship. Within each iteration of this statistical-based algorithm, a sequential design algorithm is used for the design and training of the feedforward network to provide rapid convergence to the network goals. Here, at each sequence a new network is trained to minimize the error of previous network. The proposed method should work for applications wherein an arbitrary large source of training data can be generated. Two numerical examples are performed on a spacecraft application in order to demonstrate the feasibility of the proposed approach.

Maghami, Peiman G.↗

NASA NTRS1973

The shock tube as a tool for dynamic testing of fabrics

Specimens of fabric and Mylar were loaded to failure both statically and dynamically. Static tests were accomplished by pressurizing the specimens and dynamic tests were conducted by firing a shock tube. The results of the study indicate that seam efficiency is degraded by dynamic loads and that a need exists to investigate a seaming procedure which gives an optimum dynamic efficiency. The study also illustrates the lack of correspondence between static and dynamic breaking strengths thereby indicating that fabrics which have dynamic applications should be evaluated using dynamic testing procedures such as the shock tube loading used in the present program.

Madden, R.↗

NASA NTRS1973

Development and application of a local linearization algorithm for the integration of quaternion rate equations in real-time flight simulation problems

High angular rates encountered in real-time flight simulation problems may require a more stable and accurate integration method than the classical methods normally used. A study was made to develop a general local linearization procedure of integrating dynamic system equations when using a digital computer in real-time. The procedure is specifically applied to the integration of the quaternion rate equations. For this application, results are compared to a classical second-order method. The local linearization approach is shown to have desirable stability characteristics and gives significant improvement in accuracy over the classical second-order integration methods.

Barker, L. E., Jr.↗

NASA NTRS1983

Nonlinear structural dynamics analysis using a modified modal method

The procedure for predicting the nonlinear dynamic response of structural components subjected to a step loading is presented. The procedure is a modified modal method that involves a change of dependent variables from the unknown nodal degrees of freedom of the finite element model of the structure to a smaller set of generalized coordinates. This change of dependent variables uses a combination of the nonlinear static solution and some selected vibration mode shapes. The vibration mode shapes correspond to the eigenvectors obtained by solving a standard free vibration eigenvalue problem wherein the stiffness matrix is expanded about the nonlinear static solution. A strategy is also presented for determining which and how many vibration mode shapes to include in the transformation. The effect of inaccurate representation of the spatial distribution of the applied load on the nonlinear dynamic response is discussed for two classes of structural behavior. Application of the procedure to structures which exhibit a stiffening behavior and to those with a softening behavior is presented.

Knight, N. F., Jr.↗

NASA NTRS1995

Integrated aerodynamic/dynamic/structural optimization of helicopter rotor blades using multilevel decomposition

This paper describes an integrated aerodynamic/dynamic/structural (IADS) optimization procedure for helicopter rotor blades. The procedure combines performance, dynamics, and structural analyses with a general-purpose optimizer using multilevel decomposition techniques. At the upper level, the structure is defined in terms of global quantities (stiffness, mass, and average strains). At the lower level, the structure is defined in terms of local quantities (detailed dimensions of the blade structure and stresses). The IADS procedure provides an optimization technique that is compatible with industrial design practices in which the aerodynamic and dynamic designs are performed at a global level and the structural design is carried out at a detailed level with considerable dialog and compromise among the aerodynamic, dynamic, and structural groups. The IADS procedure is demonstrated for several examples.

Walsh, Joanne L.↗