Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic Boundary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Performance analysis and tank test validation of a hybrid ocean wave-current energy converter with a single power takeoff

This paper introduces a hybrid ocean wave-current energy converter (HWCEC) that harvests energy from ocean waves and current simultaneously with a single power takeoff (PTO). Specifically, the wave energy is extracted through relative heaving motion between a floating buoy and a submerged second body, while the current energy is extracted using a marine current turbine (MCT). Energy from both sources are integrated by a hybrid PTO whose concept is based on a mechanical motion rectifier (MMR). The hybrid PTO with two one-way clutches converts bidirectional, up-and-down motion from the waves into unidirectional rotation of the generator. Meanwhile a third one-way clutch couples the MCT with the same generator. The wave and current can simultaneously or separately drive the same generator through different engagement and disengagement statuses of the one-way clutches. Time-domain simulation is conducted with hydrodynamic coefficients obtained from computational fluid dynamics analysis and boundary element method. Tank tests were conducted for a HWCEC under co-existing wave and current inputs. For comparison, separate baseline tests of a turbine and a two-body point absorber, each acting in isolation, are conducted. Experimental results validate the dynamic modeling and show that a HWCEC can increase the output power with a range between 29-87% over either current turbine and wave energy converter acting individually, and it can reduce by up to 70% the peak-to-average power ratio compared with the wave energy converter on the tested conditions.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Dislocation transmission across Σ3{112} incoherent twin boundary: a combined atomistic and phase-field study

Grain boundaries (GBs) in polycrystalline materials act as impediments to dislocation motion and result in strengthening. Understanding slip transmission through GBs, specifically twin boundaries, is essential to understand the plastic deformation behavior of polycrystalline fcc materials. Here the interaction between a glide dislocation and Σ3{112} incoherent twin boundary (ITB) in copper is investigated using a combined atomistic and mesoscale approach. The material parameters and structure of the GB in the mesoscale phase field dislocation dynamics (PFDD) model are informed from Molecular Statics (MS) simulations. The structural unit of the ITB consists of an array of three partial dislocations. The interaction between a glide dislocation impinging on each of the GB partial dislocations is investigated using both PFDD and Molecular Dynamics (MD) with two boundary conditions. Transmission planes predicted by both PFDD and MD (NVT) are in agreement, and show that not all transmission events are direct. Critical transmission stresses predicted by PFDD are in the range of 276 MPa to 1380 MPa, while MD predictions are in the range from 100 MPa to 700 MPa. The PFDD and MD predictions of slip transmission are explained using dislocation theory based on isotropic linear elasticity.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Integrating continuous atmospheric boundary layer and tower-based flux measurements to advance understanding of land-atmosphere interactions

The atmospheric boundary layer mediates the exchange of energy, matter, and momentum between the land surface and the free troposphere, integrating a range of physical, chemical, and biological processes and is defined as the lowest layer of the atmosphere (ranging from a few meters to 3 km). In this review, we investigate how continuous, automated observations of the atmospheric boundary layer can enhance the scientific value of co-located eddy covariance measurements of land-atmosphere fluxes of carbon, water, and energy, as are being made at FLUXNET sites worldwide. We highlight four key opportunities to integrate tower-based flux measurements with continuous, long-term atmospheric boundary layer measurements: (1) to interpret surface flux and atmospheric boundary layer exchange dynamics and feedbacks at flux tower sites, (2) to support flux footprint modelling, the interpretation of surface fluxes in heterogeneous terrain, and quality control of eddy covariance flux measurements, (3) to support regional-scale modeling and upscaling of surface fluxes to continental scales, and (4) to quantify land-atmosphere coupling and validate its representation in Earth system models. Adding a suite of atmospheric boundary layer measurements to eddy covariance flux tower sites, and supporting the sharing of these data to tower networks, would allow the Earth science community to address new emerging research questions, better interpret ongoing flux tower measurements, and would present novel opportunities for collaborations between FLUXNET scientists and atmospheric and remote sensing scientists.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Grain Growth and Coarsening Dynamics in a Compositionally Asymmetric Block Copolymer Revealed by X-ray Photon Correlation Spectroscopy

The dynamics of nanostructured soft materials crucially impact their associated macroscopic material properties, yet they are often difficult to measure due to spatiotemporal limitations of conventional instrumentation. Herein, we use X-ray photon correlation spectroscopy (XPCS) to directly observe particle-scale dynamics during grain growth and coarsening in a BCC- forming diblock polymer melt, with specific attention to the distribution of structural relaxation times associated with the interplanar (110) distance. Following sample quenching from the disordered state, these dynamical phenomena surprisingly exhibit little dependence on time and thermal quench depth. We posit that these relaxations stem from collective particle motions during grain rotation. We also observe unusual internally-referenced heterodyne correlations, which enable measurements of speed distributions within the sample. In this work, these speeds are significantly slower and appear at much longer annealing times than those previously reported during grain nucleation and growth in microphase separated block polymer melts. Drawing on analogies between polycrystalline hard and soft materials, we ascribe these speed distributions to misorientation-dependent grain boundary migration during ordered domain coarsening and anomalously fast, cooperative string-like particle motion along the grain boundaries. Thus, these coherent X-ray measurements provide new opportunities to interrogate grain boundary structure and dynamics in polycrystalline soft materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Exploring the Meteorological Impacts of Surface and Rooftop Heat Mitigation Strategies Over a Tropical City

Different heat mitigation technologies have been developed to improve the thermal environment in cities. However, the regional impacts of such technologies, especially in the context of a tropical city, remain unclear. The deployment of heat mitigation technologies at city-scale can change the radiation balance, advective flow, and energy balance between urban areas and the overlying atmosphere. We used the mesoscale Weather Research and Forecasting model coupled with a physically based single-layer urban canopy model to assess the impacts of five different heat mitigation technologies on surface energy balance, standard surface meteorological fields, and planetary boundary layer (PBL) dynamics for premonsoon typical hot summer days over a tropical coastal city in the month of April in 2018, 2019, and 2020. Results indicate that the regional impacts of cool materials (CMs), super-cool broadband radiative coolers, green roofs (GRs), vegetation fraction change, and a combination of CMs and GRs (i.e., “Cool city (CC)”) on the lower atmosphere are different at diurnal scale. Results showed that super-cool materials have the maximum potential of ambient temperature reduction of 1.6°C during peak hour (14:00 LT) compared to other technologies in the study. During the daytime hours, the PBL height was considerably lower than the reference scenario with no implementation of strategies by 700 m for super-cool materials and 500 m for both CMs and CC cases; however, the green roofing system underwent nominal changes over the urban area. During the nighttime hours, the PBL height increased by CMs and the CC strategies compared to the reference scenario, but minimal changes were evident for super-cool materials. The changes of temperature on the vertical profile of the heat mitigation implemented city reveal a stable PBL over the urban domain and a reduction of the vertical mixing associated with a pollution dome. This would lead to crossover phenomena above the PBL due to the decrease in vertical wind speed. Therefore, assessing the coupled regional impact of urban heat mitigation over the lower atmosphere at city-scale is urgent for sustainable urban planning.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Investigating the Interaction Between Circulating Tumor Cells and Local Hydrodynamics via Experiment and Simulations

Introduction: The biological and mechanical properties of circulating tumor cells (CTCs) in combination with the hemodynamics affect the preference of metastatic sites in the vasculature. Despite the extensive literature on the effects of biological properties on cell adhesion, the effects of hydrodynamic forces on primary attachment remains an active area of research. Here, using simulations in conjunction with experimentation, we provide new insight into the interplay of CTCs dynamics and local hydrodynamics. Methods: A flow experiment of CTC attachment was performed within a bioprinted, double branching endothelialized vessel. Simulations of fluid flow and CTC transport in the reconstructed and idealized bifurcated vessel were respectively performed by HARVEY, our in-house massively parallel computational fluid dynamics solver. HARVEY is based on the lattice Boltzmann and finite element methods to model the fluid and cells dynamics. The immersed boundary method is employed for resolving the fluid–structure interaction. Results: CTC attachment was quantified experimentally at all regions of the complex vessel. The results demonstrate a clear preference for CTCs to attach at the branch points. To elucidate the effect of the vessel topology on the location of attachment, a fluid-only simulation was performed assessing the differences in the hydrodynamics along the vessel. CTC transport in idealized bifurcated vessels was subsequently studied to examine the effects of cell deformability on the local hydrodynamics patterns and, thus, the preference of attachment sites. Conclusions: The current work provides evidence on the correlation of the hydrodynamics forces arising from the vessel topology and CTC properties on the attachment regions.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2021

Accounting for the effect of dislocation climb-mediated flow on the anisotropy and texture evolution of Mg alloy, AZ31B

The current study explores the role that dislocation climb has in mediating plasticity a Mg alloy at moderately elevated temperatures. Interrupted tensile tests were performed on samples of Mg alloy, AZ31B, sheet in the O temper condition over a range of strain rates (10 -5 to 10 -1 s -1 ) and temperatures (20–350°C) along the rolling and transverse directions. Experimental measurements of the resulting strain anisotropy and texture evolution were used as constraints during a parametric study employing a new crystal plasticity model (VPSC-CLIMB), which explicitly accounts for the kinematics of dislocation climb. The results reveal that the climb of basal (a) dislocations is not only important for dislocation recovery, but also demonstrate that climb accommodates a significant fraction of the strain in conditions where a power-law creep-type constitutive response prevails. This work does not discredit the notion that non-basal slip of (a) and (c+a) dislocations is important over a wide range of temperatures and strain rates. However, it demonstrates that the activation of dislocation climb as the mechanistic change within the power law regime provides an explanation for a wide range of observations, including the simultaneous reduction in strain anisotropy, slowed texture evolution, and rapid increase in strain rate sensitivity. Finally, it is hypothesized that these conclusions may even apply to cases in which grain boundary sliding and/or dynamic recrystallization are observed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A Closed Bay-Breeze Circulation and Its Lifecycle From TRACER With a New Orienteering Tape Recorder Diagram

A closed bay-breeze circulation (BBC) followed by a gulf-breeze front (GBF) was observed on 10 September 2022 during the Department of Energy's (DOE) Atmospheric Radiation Measurement (ARM) TRACER campaign. Using high-resolution X-band Scanning Cloud Radar (XSACR) and a newly developed orienteering tape recorder diagram, the study analyzed radar reflectivity and Doppler velocity to identify anomalies and track the evolution of these circulations. The BBC, a mesoscale system approximately 30-km long, 30-km wide, and 2-km deep, formed from enhanced horizontal convective rolls along the Galveston Bay coast, progressing northwestward under a 6 m s−1 onshore flow anomaly and reaching 1.5 km depth with return flow aloft. The inland penetration speed was 2 m s−1, driven by an observed 6-9 K land-water temperature contrast. The GBF, coupled to the BBC, intensified with additional southerly flow, penetrating further inland after the BBC collapsed. Passing over the TRACER field site, both fronts significantly impacted boundary layer thermodynamics, dynamics, and aerosol concentration. The BBC event exhibited four lifecycle stages-formation, development, maturation, and dissipation-driven by solar heating, wind field rotation, and interactions with convective eddies and the GBF. This study provides insights into the inland evolution of coastal breeze circulations and their interactions with environmental processes.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2026

In-line measurements of below-the-surface food deformation during drying with an interference-based optical fiber strain sensor

Real-time measurements of food deformation are important for quality control in drying, yet they pose significant challenges. In this study, we developed an interference-based optical fiber strain sensor to enable in-line, continuous, below-the-surface strain measurements in drying of soft food samples. Compared to a strain resolution of 8 × 10 -4 at zero strain and 7.2 × 10 -3 at 0.20 strain reported in our previously published work, the present study achieves markedly improved resolutions of 1.3 × 10 -4 at zero strain and 7.8 × 10 -4 at 0.25 strain, which strains are the lower and higher boundaries of the dynamic range, respectively. This nearly order-of-magnitude improvement is attributed to the unique interference-based sensing mechanism, no need for calibration to convert optical signals to strain, and the system-design-enabled immunity to fiber-disk misalignments and light source intensity fluctuations. To demonstrate the in-line process monitoring, deformation measurements of fresh banana slices and sugar cookie doughs were carried out in a benchtop oven and an industrial-scale hot-air pilot dryer, respectively. In both dryers, strain measurements were continuously measured during the whole drying process at various depths and radii below the sample surfaces, with the strains up to 25%. Computer vision was used only in the benchtop drying to confirm the faithfulness of the fiber sensor measurements and cannot provide below-the-surface measurements. The measured spatiotemporal deformation allowed us to confirm the shell-hardening effect and to determine the speed and location of large deformation changes in the whole drying process, the latter of which is related to the sample cracking. To the best of the authors’ knowledge, this study is the first to report on an interferometry-based fiber sensor to measure food deformation. This sensor and the sensing mechanism have high potential for real-time process monitoring and control to prevent over-drying or cracking during drying processes.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Fermionic Isometric Tensor Network States in Two Dimensions

We generalize isometric tensor network states to fermionic systems, paving the way for efficient adaptations of 1D tensor network algorithms to 2D fermionic systems. As the first application of this formalism, we developed and benchmarked a time-evolving block-decimation (TEBD) algorithm for real-time and imaginary-time evolution. The imaginary-time evolution produces ground-state energies for gapped systems, systems with a Dirac point, and systems with gapless edge modes to good accuracy. Here, the real-time TEBD captures the scattering of two fermions and the chiral edge dynamics on the boundary of a Chern insulator.

2-dimensional systems↗
DOE OSTI2023

A Secure and Adaptive Hierarchical Multi-Timescale Framework for Resilient Load Restoration Using a Community Microgrid

Distribution system integrated community microgrids (CMGs) can partake in restoring loads during extended duration outages. At such times, the CMGs are challenged with limited resource availability, absence of robust grid support, and heightened demand-supply uncertainty. Here, this paper proposes a secure and adaptive three-stage hierarchical multi-timescale framework for scheduling and real-time (RT) dispatch of CMGs with hybrid PV systems to address these challenges. The framework enables the CMG to dynamically expand its boundary to support the neighboring grid sections and is adaptive to the changing forecast error impacts. The first stage solves a stochastic extended duration scheduling (EDS) problem to obtain referral plans for optimal resource rationing. The intermediate near-real-time (NRT) scheduling stage updates the EDS schedule closer to the dispatch time using new obtained forecasts, followed by the RT dispatch stage. To make the decisions more secure and robust against forecast errors, a novel concept called delayed recourse is designed. The approach is evaluated via numerical simulations on a modified IEEE 123-bus system and validated using OpenDSS and hardware-in-loop simulations. The results show superior performance in maximizing load supply and continuous secure distribution network operation under different operating scenarios.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

Examining the Impacts of Great Lakes Temperature Perturbations on Simulated Precipitation in the Northeastern United States

Most inland water bodies are not resolved by general circulation models, requiring that lake surface temperatures be estimated. Given the large spatial and temporal variability of the surface temperatures of the North American Great Lakes, such estimations can introduce errors when used as lower boundary conditions for dynamical downscaling. Lake surface temperatures (LSTs) influence moisture and heat fluxes, thus impacting precipitation within the immediate region and potentially in regions downwind of the lakes. For this study, the Advanced Research version of the Weather Research and Forecasting Model (WRF-ARW) was used to simulate precipitation over the six New England states during a 5-yr historical period. The model simulation was repeated with perturbed LSTs, ranging from 10°C below to 10°C above baseline values obtained from reanalysis data, to determine whether the inclusion of erroneous LST values has an impact on simulated precipitation and synoptic-scale features. Results show that simulated precipitation in New England is statistically correlated with LST perturbations, but this region falls on a wet–dry line of a larger bimodal distribution. Wetter conditions occur to the north and drier conditions occur to the south with increasing LSTs, particularly during the warm season. Additionally, the precipitation differences coincide with large-scale anomalous temperature, pressure, and moisture patterns. Care must therefore be taken to ensure reasonably accurate Great Lakes surface temperatures when simulating precipitation, especially in southeastern Canada, Maine, and the mid-Atlantic region.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Grain growth of nanocrystalline aluminum under tensile deformation: A combined in situ TEM and atomistic study

Nanocrystalline Al thin films have been strained in situ in a transmission electron microscope using two separate nanomechanical techniques involving a push-to-pull device and a microelectromechanical system (MEMS) device. Deformation-induced grain growth was observed to occur via stress-assisted grain boundary migration with extensive grain growth occurring in the necked region, indicating that the increase in local stress drives the boundary migration. Under applied tensile stresses close to the ultimate tensile strength of 450 MPa for a nanocrystalline Al specimen, measured boundary migration speeds are 0.2 – 0.7 nm s -1 for grains outside necked region and increases to 2.5 nm s -1 for grains within the necked region where the local estimated tensile stresses are elevated to around 630 MPa. By tracking grain boundary motion over time, molecular dynamics simulations showed qualitative agreement in terms of pronounced grain boundary migration with the experimental observations. The combined in situ observation and molecular dynamics simulation results underscore the important role of stress-driven grain growth in plastically deforming nanocrystalline metals, leading to intergranular fracture through predominant grain boundary sliding in regions with large localized deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The effect of grain boundary yield and disconnections on grain boundary fracture strength

During high-temperature interfacial strain, e.g., creep or sintering, grain boundaries will sample non-equilibrium states associated with the non-equilibrium disconnections that mediate strain. This work tests the hypothesis that those non-equilibrium states should affect the mechanical properties of the grain boundary. High-temperature bicrystal tensile strain experiments performed on Sc-doped ZrO 2 as a function of strain rate enable the observation of fracture before and after grain boundary yield. Yielded boundaries exhibit a median fracture strength ≈ 50 % lower than those that did not yield. Molecular dynamics simulations performed on boundaries with and without interstitial-type disconnection loops indicate that the presence of those loops reduce the failure stress.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Simulations of tokamak edge plasma turbulent fluctuations based on a minimal 3D model

In this study, a new simulation model for tokamak boundary plasma, SOLT3D, is implemented in the BOUT++ framework. The simulation model includes a set of dynamic equations describing collisional boundary plasma and neutral gas in the tokamak scrape-off layer and divertor region. The model is verified against standard linear plasma instabilities and available nonlinear results. For L-mode like conditions, SOLT3D reproduces characteristics of boundary plasma turbulent fluctuations that are similar to published experimental data, in terms of the amplitude and spatial dependence of the fluctuations. It also reproduces realistic plasma fluxes on material surfaces and expected Bohm-like effective radial transport. Plasma fluctuations inferred from the simulations imply inevitably a significant level of intrinsic 'noise' for axisymmetric tokamak plasma transport modeling, introducing errors on the order of unity. In particular, the toroidally averaged atomic rates below 5–10 eV are strongly modified by turbulent plasma fluctuations, which should significantly affect the standard axisymmetric modeling of the tokamak edge plasma and divertor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Reduction of vanadium diffusivity within copper grain boundaries due to enhanced binding

We investigate permeation of vanadium (V) through copper (Cu) layers in V/Cu/niobium (Nb) and molybdenum (Mo)/Cu/V tri-layer composites and compare it with the permeation behavior of Nb. Despite their low solubility in single-crystal Cu, both V and Nb permeate readily due to short-circuit transport through Cu grain boundaries (GBs). However, Nb permeates preferentially to V. Atomistic simulations suggest that this difference is due to lower V diffusivity at general GBs in Cu, compared to Nb. Here, the lower V diffusivity, in turn, arises from stronger V binding to the boundary, which manifests as a greater equilibrium GB concentration as well as a higher activation energy for GB diffusion.

36 MATERIALS SCIENCE↗