Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Diffuse fraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Shock-implanted noble gases - An experimental study with implications for the origin of Martian gases in shergottite meteorites

The shock-implantation of gases is studied by artificially shocking whole rock and power samples of terrestrial basalt to pressures of 2-40 GPa. Ar, Kr, Xe, and Ne were implanted into the silicate. It is observed that the amount of implanted gas is linearly proportional to its partial pressure over a pressure range of 0.0001 to 0.1 atmosphere. The fractionation effect in the implanted gas and the gas diffusion properties are examined. The amounts of gas that would have been implanted with 100 percent efficiency are calculated from the measured porosities of the power samples and are compared to observed abundances. It is determined that the implantation efficiencies are approximately 0.5 percent at 2 GPa, 7 percent at 5 GPa, and greater than 50 percent at both 20 and 35 GPa. The experimental data correlate with the shock implantation of Martian gases without mass fractionation into the shock-melted phase of meteorite EETA 79001.

Bogard, Donald D.↗
NASA NTRS1995

Polarimetry of the Interstellar Medium

The talk will review what is known about the composition of ices and organics in the dense and diffuse interstellar media (ISM). Mixed molecular ices make up a significant fraction of the solid materials in dense molecular clouds and it is now known that thermal and radiation processing of these ices results in the production of more complex organic species, some of which may survive transport into forming stellar systems and the diffuse ISM. Molecular species identified in interstellar ices include H2O, CH3OH, CO, CH4, CO2, and somewhat surprisingly, H2. Theoretical and laboratory studies of the processing of interstellar analog ices containing these species indicate that species like HCO, H2CO, CH3, and NH3 are readily made and should also be present. The irradiation of mixed molecular ices containing these species, when followed by warming, leads to the production of a large variety of more complex species, including ethanol (CH3CH2OH), formamide (HC(=O)NH2), acetamide (CH3C(=O)NH2), nitriles or isonitriles (R-CN or R-NC hexamethylenetetramine (HMT; C6H12N4), a number of polymeric species related to polyoxymethylene [POM,(-CH2O-)n], and ketones {R-C(=O)-R'}. Spectral studies of dust in the diffuse ISM indicate the presence of fairly complex organics, some of which may be related to the organics produced in dense molecular clouds. Spectral comparisons indicate that the diffuse ISM organics may be quite similar to meteoritic kerogens, i.e. they may consist largely of aromatic moieties interlinked by short aliphatic bridges. Interestingly, recent evidence indicates that the galactic distribution of this material closely matches that of silicates, but does not correlate directly with visual extinction. This implies that a large fraction of the visual extinction is caused by a material other than these organics and silicates and that this other material has a significantly different distribution within the galaxy.

Sandford, Scott↗
NASA NTRS1999

Periodic Excitation for Jet Vectoring and Enhanced Spreading

The effects of periodic excitation on the evolution of a turbulent jet were studied experimentally. A short, wide-angle diffuser was attached to the jet exit and excitation was introduced at the junction between the jet exit and the diffuser inlet. The introduction of high amplitude periodic excitation at the jet exit enhances the mixing and promotes attachment of the jet shear-layer to the diffuser wall. Vectoring is achieved by applying the excitation over a fraction of the circumference of the circular jet, enhancing its spreading rate on the excited side and its tendency to reattach to that side. Static deflection studies demonstrate that the presence of the wide-angle diffuser increases the effectiveness of the added periodic momentum due to a favorable interaction between the excitation, the jet shear-layer and the diffuser wall. This point was further demonstrated by the evolution of a wave packet that was excited in the jet shear-layer. Strong amplification of the wave packet was measured with a diffuser attached to the jet exit. The turbulent jet responds quickly (10-20 msec) to step changes in the level of the excitation input. The response scales with the jet exit velocity and is independent of the Reynolds number. Jet deflection angles were found to be highly sensitive to the relative direction between the excitation and the jet flow and less sensitive to the excitation frequency. The higher jet deflection angles were obtained for a diffuser length of about two diameters and for diffusers with half-angles greater than 15 degrees.

Pack, LaTunia G.↗
NASA NTRS1984

Analysis techniques for tracer studies of oxidation

Analysis techniques to obtain quantitative diffusion data from tracer concentration profiles were developed. Mass balance ideas were applied to determine the mechanism of oxide growth and to separate the fraction of inward and outward growth of oxide scales. The process of inward oxygen diffusion with exchange was theoretically modelled and the effect of lattice diffusivity, grain boundary diffusivity and grain size on the tracer concentration profile was studied. The development of the tracer concentration profile in a growing oxide scale was simulated. The double oxidation technique was applied to a FeCrAl-Zr alloy using 0-18 as a tracer. SIMS was used to obtain the tracer concentration profile. The formation of lacey oxide on the alloy was discussed. Careful consideration was given to the quality of data required to obtain quantitative information.

Basu, S. N.↗
NASA NTRS1992

Structure of turbulent non-premixed flames modeled with two-step chemistry

Direct numerical simulations of turbulent diffusion flames modeled with finite-rate, two-step chemistry, A + B yields I, A + I yields P, were carried out. A detailed analysis of the turbulent flame structure reveals the complex nature of the penetration of various reactive species across two reaction zones in mixture fraction space. Due to this two zone structure, these flames were found to be robust, resisting extinction over the parameter ranges investigated. As in single-step computations, mixture fraction dissipation rate and the mixture fraction were found to be statistically correlated. Simulations involving unequal molecular diffusivities suggest that the small scale mixing process and, hence, the turbulent flame structure is sensitive to the Schmidt number.

Chen, J. H.↗
NASA NTRS1997

Laser-Induced Incandescence in Microgravity

Knowledge of soot concentration is important due to its presence and impact upon a wide range of combustion processes ranging from diffusion to premixed flames, laminar to turbulent processes and homogeneous to heterogeneous combustion. Measurement of soot volume fraction (f(sub v)) is essential to discerning its formation and growth. The presence of soot also affects other physical and chemical properties of combustion thereby affecting studies not directly concerned with either its formation or growth, such as radiative heat transfer, CO oxidation and fuel vaporization or pyrolysis rates. Microgravity offers unique opportunities for studying both soot growth and the effect of soot radiation upon flame structure and spread. Spatial scales and residence time scales are greatly extended in 0-g facilitating soot growth studies. With the varied geometries, short duration microgravity test times and time-varying processes there is a demand for measurement of f(sub v) with high spatial and temporal resolution. Laser-induced incandescence (LII) has advanced f(sub v) measurements in many 1-g combustion processes. To create laser-induced incandescence, a pulsed high intensity laser heats soot to incandescence temperatures. Using appropriate spectral and temporal detection conditions, the resulting incandescence can be selectively detected apart from the non-laser-heated soot and flame gases. Theoretical modelling and experiments have shown that the resulting incandescence is representative of f(sub v). Using an intensified array camera and a laser sheet for excitation, one- and two-dimensionally resolved LII images of f(sub v) have been obtained in 1-g. LII has been characterized and developed at NASA-Lewis for soot volume fraction determination in a wide range of 1-g combustion applications. Broadly grouped, the characterization work has included studies of excitation intensity, excitation wavelength and the optimum temporal and spectral detection conditions to enable an accurate representation of soot volume fraction by LII. Tests for special requirements imposed by different combustion processes have been performed in laminar and turbulent diffusion flames, rich sooting premixed flames, single droplet combustion, and other heterogeneous combustion. These studies demonstrated LII's high sensitivity, temporal and spatial capabilities and its geometric versatility. In contrast to the advantages offered to combustion studies by a microgravity environment, advanced diagnostics, specifically those requiring pulsed laser diagnostics have been limited due to the size, weight and power limitations in a low-gravity environment. Reported here are the first demonstrations of LII performed in a microgravity environment. Examples are shown for laminar and turbulent gas-jet diffusion flames in 0-g.

VanderWal, Randy L.↗
NASA NTRS1982

Thermal and nonthermal escape mechanisms for terrestrial bodies

A survey is given of the classical thermal escape (Jeans or blowoff) and some eight nonthermal processes involving ions. Diffusional, energetic, and other limitations on the escape flux are discussed. Isotopic fractionation, due to differences in thermal escape rates or diffusive separation, is considered. The dominant processes acting at the five terrestrial planets and six major satellites are summarized. In general, nonthermal processes dominate over the classic thermal ones.

Hunten, D. M.↗
NASA NTRS1996

Theoretical and Numerical Investigation of Radiative Extinction of Diffusion Flames

The influence of soot radiation on diffusion flames was investigated using both analytical and numerical techniques. Soot generated in diffusion flames dominate the flame radiation over gaseous combustion products and can significantly lower the temperature of the flame. In low gravity situations there can be significant accumulation of soot and combustion products in the vicinity of the primary reaction zone owing to the absence of any convective buoyant flow. Such situations may result in substantial suppression of chemical activities in a flame, and the possibility of a radiative extinction may also be anticipated. The purpose of this work was to not only investigate the possibility of radiative extinction of a diffusion flame but also to qualitatively and quantitatively analyze the influence of soot radiation on a diffusion flame. In this study, first a hypothetical radiative loss profile of the form of a sech(sup 2) was assumed to influence a pure diffusion flame. It was observed that the reaction zone can, under certain circumstances, move through the radiative loss zone and locate itself on the fuel side of the loss zone contrary to our initial postulate. On increasing the intensity and/or width of the loss zone it was possible to extinguish the flame, and extinction plots were generated. In the presence of a convective flow, however, the movement of the temperature and reaction rate peaks indicated that the flame behavior is more complicated compared to a pure diffusional flame. A comprehensive model of soot formation, oxidation and radiation was used in a more involved analysis. The soot model of Syed, Stewart and Moss was used for soot nucleation and growth and the model of Nagle and Strickland-Constable was used for soot oxidation. The soot radiation was considered in the optically thin limit. An analysis of the flame structure revealed that the radiative loss term is countered both by the reaction term and the diffusion term. The essential balance for the soot volume fraction was found to be between the processes of soot convection and soot growth. Such a balance yielded to analytical treatment and the soot volume fraction could be expressed in the form of an integral. The integral was evaluated using two approximate methods and the results agreed very well with the numerical solutions for all cases examined.

Ray, Anjan↗
NASA NTRS2001

Multiple Mode Actuation of a Turbulent Jet

The effects of multiple mode periodic excitation on the evolution of a circular turbulent jet were studied experimentally. A short, wide-angle diffuser was attached to the jet exit. Streamwise and cross-stream excitations were introduced at the junction between the jet exit and the diffuser inlet on opposing sides of the jet. The introduction of high amplitude, periodic excitation in the streamwise direction enhances the mixing and promotes attachment of the jet shear-layer to the diffuser wall. Cross-stream excitation applied over a fraction of the jet circumference can deflect the jet away from the excitation slot. The two modes of excitation were combined using identical frequencies and varying the relative phase between the two actuators in search of an optimal response. It is shown that, for low and moderate periodic momentum input levels, the jet deflection angles depend strongly on the relative phase between the two actuators. Optimum performance is achieved when the phase difference is pi +/- pi/6. The lower effectiveness of the equal phase excitation is attributed to the generation of an azimuthally symmetric mode that does not produce the required non-axisymmetric vectoring. For high excitation levels, identical phase becomes more effective, while phase sensitivity decreases. An important finding was that with proper phase tuning, two unsteady actuators can be combined to obtain a non-linear response greater than the superposition of the individual effects.

Pack, LaTunia G.↗
NASA NTRS2001

Multiple Mode Actuation of a Turbulent Jet

The effects of multiple mode periodic excitation on the evolution of a circular turbulent jet were studied experimentally. A short, wide-angle diffuser was attached to the jet exit. Streamwise and cross-stream excitations were introduced at the junction between the jet exit and the diffuser inlet on opposing sides of the jet. The introduction of high amplitude, periodic excitation in the streamwise direction enhances the mixing and promotes attachment of the jet shear-layer to the diffuser wall. Cross-stream excitation applied over a fraction of the jet circumference can deflect the jet away from the excitation slot. The two modes of excitation were combined using identical frequencies and varying the relative phase between the two actuators in search of an optimal response. It is shown that, for low and moderate periodic momentum input levels, the jet deflection angles depend strongly on the relative phase between the two actuators. Optimum performance is achieved when the phase difference is pi +/- pi/6. The lower effectiveness of the equal phase excitation is attributed to the generation of an azimuthally symmetric mode that does not produce the required non-axisymmetric vectoring. For high excitation levels, identical phase becomes more effective, while phase sensitivity decreases. An important finding was that with proper phase tuning, two unsteady actuators can be combined to obtain a non-linear response greater than the superposition of the individual effects.

Pack, LaTunia G.↗
NASA NTRS2006

The EPIC-MOS Particle-Induced Background Spectrum

We have developed a method for constructing a spectrum of the particle-induced instrumental background of the XMM-Newton EPIC MOS detectors that can be used for observations of the diffuse background and extended sources that fill a significant fraction of the instrument field of view. The strength and spectrum of the particle-induced background, that is, the background due to the interaction of particles with the detector and the detector surroundings, is temporally variable as well as spatially variable over individual chips. Our method uses a combination of the filter-wheel-closed data and a database of unexposed-region data to construct a spectrum of the "quiescent" background. We show that, using this method of background subtraction, the differences between independent observations of the same region of "blank sky" are consistent with the statistical uncertainties except when there is clear evidence of solar wind charge exchange emission. We use the blank sky observations to show that contamination by SWCX emission is a strong function of the solar wind proton flux, and that observations through the flanks of the magnetosheath appear to be contaminated only at much higher solar wind fluxes. We have also developed a spectral model of the residual soft proton flares, which allows their effects to be removed to a substantial degree during spectral fitting.

Kuntz, K. D.↗
NASA NTRS1975

K-alpha X-rays from cosmic ray oxygen

Equilibrium charge fractions are calculated for subrelativistic cosmic ray oxygen ions in the interstellar medium. These are used to determine the expected flux of K-alpha rays arising from atomic processes for a number of different postulated interstellar oxygen spectra. Relating these results to the diffuse X-ray background measured at the appropriate energy level suggests an observable line feature. If the flux of low energy cosmic ray oxygen is sufficiently large, K-alpha X-ray line emission from these nuclei will comprise a significant fraction of the total diffuse flux at approximately 0.6 keV. A satellite borne detector with a resolution greater than 30 percent could observe this feature if the subrelativistic interstellar cosmic ray oxygen spectrum is as large as certain theoretical estimates expressed in the text.

Pravdo, S. H.↗
NASA NTRS1975

Better vacuum by removal of diffusion-pump-oil contaminants

The complex problem of why large space simulation chambers do not realize true ultimate vacuum was investigated. Some contaminating factors affecting diffusion pump performance were identified, and some advances in vacuum distillation-fractionation technology were achieved which resulted in a two-decade-or-more lower ultimate pressure. Data are presented to show the overall or individual contaminating effects of commonly used phthalate ester plasticizers of 390 to 530 molecular weight on diffusion pump performance. Methods for removing contaminants from diffusion pump silicone oil during operation and for reclaiming contaminated oil by high-vacuum molecular distillation are described. Conceptual self-cleansing designs and operating procedures are proposed for modifying large diffusion pumps into high-efficiency distillation devices. The potential exists for application of these technological advancements to other disciplines, such as medicine, biomedical materials, metallurgy, refining, and chemical (diffusion-enrichment) processing.

Buggele, A. E.↗
NASA NTRS1994

Diffusive modification of primary zoning in olivine cores in Angrite LEW 87051

Angrite LEW 87051 consists of large olivine crystals set in a fine-grained groundmass that clearly represents a crystallized melt. A few olivines contain Ca-poor, Cr-rich cores that crystallized from a very different melt than the outer part of the crystals constituting the majority of olivine in LEW 87051. We evaluate a model in which the cores formed through fractional crystallization of one melt, then were incorporated into a different melt as xenocrysts, whereupon the original zoning patterns were modified by diffusion. Using a similar approach, we calculate zoning patterns for the cores that would result from perfect fractional crystallization, compare them with the observed zoning, and determine whether the differences could result from diffusive modification consistent with known diffusion rates for Ca, Mn, and Cr. Using distribution coefficients from the 1400 C, IW + 1 experiments, we computed CaO, Cr2O3, and MnO abundances in the hypothetical parent melt by inverting the olivine at the centers of the cores. We further assumed that the primary zoning profile for CaO is essentially unmodified, because the diffusion rate of Ca in olivine is slow. We carried out the fractional crystallization calculation until the calculated Ca content was that observed at break in zoning profiles at the outer edge of the core. We then normalized the distance of this calculated profile to the length of the observed profile in the olivine core and calculated profiles for MnO and Cr2O3. The CaO zoning profile agrees well with the observed profile. The observed MnO profile is slightly higher than the calculated profile near the edge. Diffusion calculations indicate that reversal of the general trend of primary zoning through diffusion would require that diffusion of Cr is 5-10x faster than that of Mn.

Mikouchi, T.↗
NASA NTRS1973

Oxygen and nitrogen vibration in the thermosphere

Analysis of the departure of oxygen and nitrogen molecules from the Boltzmann distribution in the thermosphere. It is concluded that the daytime production rates are too low to cause departures from the Boltzmann distribution at altitudes below about 300 km for vibrational levels containing a significant fraction of total population. It is also pointed out that diffusion cannot perturb significantly the Boltzmann distribution at altitudes below about 370 km.

Walker, J. C. G.↗
NASA NTRS1976

In situ measurements of neon in the thermosphere

The open source neutral mass spectrometer on the Atmosphere Explorer-C satellite has measured neon in the thermosphere. The absolute density of Ne is close to that predicted by using the ground level fraction by volume of Ne along with the assumption of diffusive equilibrium above 100 km. Data is presented for both geomagnetically quiet and disturbed circular orbits. At 290 km, a typical low latitude value of Ne is 3.0 x 10 to the 4th/cu cm. At this altitude Ne appears to be predominantly controlled by temperature except during magnetic disturbances, when offsetting forces due to wind systems may be present.

Potter, W. E.↗
NASA NTRS1990

Diamonds in detonation soot

Diamonds 4 to 7 nm in diameter have been identified and partially isolated from soot formed in detonations of carbon-forming composite explosives. The morphology of the soot has been examined by transmission electron microscopy (TEM), and the identity of the diamond has been established by the electron diffraction pattern of the TEM samples and by the X-ray diffraction (XRD) pattern of the isolated solid. Graphite is also present in the form of ribbons of turbostatic structure with a thickness of 2 to 4 nm. A fraction, about 25 percent of the soot by weight, was recovered from the crude soot after oxidation of the graphite with fuming perchloric acid. This fraction showed a distinct XRD pattern of diamond and the diffuse band of amorphous carbon. The IR spectrum of these diamonds closely matches that of diamonds recovered from meteorites (Lewis et al., 1987), perhaps indicating similar surface properties after the oxidation. If these diamonds are produced in the detonation itself or during the initial expansion, they exhibit a phenomenal crystal growth rate (5 nm/0.00001 s equal 1.8 m/hr) in a medium with a very low hydrogen/carbon ratio. Because the diamonds will be carried along with the expanding gases, they will be accelerated to velocities approaching 8 km/s.

Greiner, N. Roy↗
NASA NTRS1991

GaP betavoltaic cells as a power source

Maximum power output for the GaP cells of this study was found to be on the order of 1 microW. This resulted from exposure to 200 and 40 KeV electrons at a flux of 2 x 10(exp 9) electrons/sq cm/s, equivalent to a 54 mCurie source. The efficiencies of the cells ranged from 5 to 9 percent for 200 and 40 KeV electrons respectively. The lower efficiency at higher energy is due to a substantial fraction of energy deposition in the substrate, further than a diffusion length from the depletion region of the cell. Radiation damage was clearly observed in GaP after exposure to 200 KeV electrons at a fluence of 2 x 10(exp 12) electrons/sq cm. No discernable damage was observed after exposure to 40 KeV electrons at the same fluence. Analysis indicates that a GaP betavoltaic system would not be practical if limited to low energy beta sources. The power available would be too low even in the ideal case. By utilizing high activity beta sources, such as Sr-90/Y-90, it may be possible to achieve performance that could be suitable for some space power applications. However, to utilize such a source the problem of radiation damage in the beta cell material must be overcome.

Pool, F. S.↗