Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Differential Experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Cu-Cr-Nb-Zr Alloy for Rocket Engines and Other High-Heat- Flux Applications

Rocket-engine main combustion chamber liners are used to contain the burning of fuel and oxidizer and provide a stream of high-velocity gas for propulsion. The liners in engines such as the Space Shuttle Main Engine are regeneratively cooled by flowing fuel, e.g., cryogenic hydrogen, through cooling channels in the back side of the liner. The heat gained by the liner from the flame and compression of the gas in the throat section is transferred to the fuel by the liner. As a result, the liner must either have a very high thermal conductivity or a very high operating temperature. In addition to the large heat flux (>10 MW/sq m), the liners experience a very large thermal gradient, typically more than 500 C over 1 mm. The gradient produces thermally induced stresses and strains that cause low cycle fatigue (LCF). Typically, a liner will experience a strain differential in excess of 1% between the cooling channel and the hot wall. Each time the engine is fired, the liner undergoes an LCF cycle. The number of cycles can be as few as one for an expendable booster engine, to as many as several thousand for a reusable launch vehicle or reaction control system. Finally, the liners undergo creep and a form of mechanical degradation called thermal ratcheting that results in the bowing out of the cooling channel into the combustion chamber, and eventual failure of the liner. GRCop-84, a Cu-Cr-Nb alloy, is generally recognized as the best liner material available at the time of this reporting. The alloy consists of 14% Cr2Nb precipitates in a pure copper matrix. Through experimental work, it has been established that the Zr will not participate in the formation of Laves phase precipitates with Cr and Nb, but will instead react with Cu to form the desired Cu-Zr compounds. It is believed that significant improvements in the mechanical properties of GRCop-84 will be realized by adding Zr. The innovation is a Cu-Cr-Nb-Zr alloy covering the composition range of 0.8 to 8.1 weight percent Cr, 0.7 to 7.2 weight percent Nb, 0.1 to 1.5 weight percent Zr, and balance Cu. The alloy combines two known strengthening mechanisms - dispersion strengthening by Cr2Nb precipitates (GRCop-84), and precipitation strengthening by CuxZr (AMZIRC) - to produce a synergistic increase in the capabilities of the alloy with the goal of achieving properties greater than either of the methods could achieve alone. The anticipated advantages of the alloy are higher strength at temperatures up to 700 C, improved creep strength, and significantly higher LCF lives relative to GRCop-84. The thermal expansion, thermal conductivity, and processing of the alloy are anticipated to remain largely unchanged relative to GRCop-84.

Ellis, David L.↗
DOE OSTI2021

Modeling of Thermal Decomposition of TATB-Based Explosive for Safety Analysis

We investigate and model the cook-off behavior of LX-17 to understand the response of explosive systems in abnormal thermal environments. Decomposition has been explored via conventional ODTX (One-Dimensional Time-to-eXplosion), PODTX (ODTX with pressure-measurement), TGA (Thermo-Gravimetric Analysis), and DSC (Differential Scanning Calorimetry) experiments under isothermal and ramped temperature profiles. The data were used to fit reaction rate parameters for proposed schemes in an ALE3D computational model. This model includes chemical reactions, thermo- and hydro-dynamics, and material properties, including thermal expansion, compressibility, and strength. These parameterizations were carried out utilizing a Python evolutionary optimization method on LLNL’s high-performance computing clusters. Additional experiments are being developed to further characterize and monitor decomposition intermediates to improve the model. Once experimentally validated, this model will be scalable to several applications involving LX-17. Furthermore, the optimization methodology developed herein should be applicable to other high explosive materials.

Chemistry - Chemical explosives↗
NASA NTRS1990

Positron-inert gas differential elastic scattering

Measurements are being made in a crossed beam experiment of the relative elastic differential cross section (DCS) for 5 to 300 eV positrons scattering from inert gas atoms (He, Ne, Ar, Kr, and Xe) in the angular range from 30 to 134 deg. Results obtained at energies around the positronium (Ps) formation threshold provide evidence that Ps formation and possibly other inelastic channels have an effect on the elastic scattering channel.

Kauppila, W. E.↗
NASA NTRS1989

COBE's search for structure in the Big Bang

The launch of Cosmic Background Explorer (COBE) and the definition of Earth Observing System (EOS) are two of the major events at NASA-Goddard. The three experiments contained in COBE (Differential Microwave Radiometer (DMR), Far Infrared Absolute Spectrophotometer (FIRAS), and Diffuse Infrared Background Experiment (DIRBE)) are very important in measuring the big bang. DMR measures the isotropy of the cosmic background (direction of the radiation). FIRAS looks at the spectrum over the whole sky, searching for deviations, and DIRBE operates in the infrared part of the spectrum gathering evidence of the earliest galaxy formation. By special techniques, the radiation coming from the solar system will be distinguished from that of extragalactic origin. Unique graphics will be used to represent the temperature of the emitting material. A cosmic event will be modeled of such importance that it will affect cosmological theory for generations to come. EOS will monitor changes in the Earth's geophysics during a whole solar color cycle.

Soffen, Gerald↗
NASA NTRS2001

Modulation of lens cell adhesion molecules by particle beams

Cell adhesion molecules (CAMs) are proteins which anchor cells to each other and to the extracellular matrix (ECM), but whose functions also include signal transduction, differentiation, and apoptosis. We are testing a hypothesis that particle radiations modulate CAM expression and this contributes to radiation-induced lens opacification. We observed dose-dependent changes in the expression of beta 1-integrin and ICAM-1 in exponentially-growing and confluent cells of a differentiating human lens epithelial cell model after exposure to particle beams. Human lens epithelial (HLE) cells, less than 10 passages after their initial culture from fetal tissue, were grown on bovine corneal endothelial cell-derived ECM in medium containing 15% fetal bovine serum and supplemented with 5 ng/ml basic fibroblast growth factor (FGF-2). Multiple cell populations at three different stages of differentiation were prepared for experiment: cells in exponential growth, and cells at 5 and 10 days post-confluence. The differentiation status of cells was characterized morphologically by digital image analysis, and biochemically by Western blotting using lens epithelial and fiber cell-specific markers. Cultures were irradiated with single doses (4, 8 or 12 Gy) of 55 MeV protons and, along with unirradiated control samples, were fixed using -20 degrees C methanol at 6 hours after exposure. Replicate experiments and similar experiments with helium ions are in progress. The intracellular localization of beta 1-integrin and ICAM-1 was detected by immunofluorescence using monoclonal antibodies specific for each CAM. Cells known to express each CAM were also processed as positive controls. Both exponentially-growing and confluent, differentiating cells demonstrated a dramatic proton-dose-dependent modulation (upregulation for exponential cells, downregulation for confluent cells) and a change in the intracellular distribution of the beta 1-integrin, compared to unirradiated controls. In contrast, there was a dose-dependent increase in ICAM-1 immunofluorescence in confluent, but not exponentially-growing cells. These results suggest that proton irradiation downregulates beta 1-integrin and upregulates ICAM-1, potentially contributing to cell death or to aberrant differentiation via modulation of anchorage and/or signal transduction functions. Quantification of the expression levels of the CAMs by Western analysis is in progress.

NASA Discipline Radiation Health↗
DOE OSTI2025

Measurement of the liquid argon scintillation pulse shape using differentiable simulation in the coherent CAPTAIN-Mills experiment

The coherent CAPTAIN-Mills (CCM) experiment is a liquid argon (LAr) light collection detector searching for MeV-scale neutrino and beyond Standard Model physics signatures. Two hundred eight-inch photomultiplier tubes instrument the seven-ton fiducial volume with 50% photocathode coverage to detect light produced by charged particles. CCM’s light-based approach reduces requirements of LAr purity, compared to other detection technologies, such that sub-MeV particles can be reliably detected without additional LAr filtration and with 𝒪⁡(1) parts per million of common contaminants. We present a measurement of LAr light production and propagation parameters, with uncertainties, obtained from a sample of MeV-scale electromagnetic events. The optimization of this high-dimensional parameter space was facilitated by a differentiable optical photon Monte Carlo simulation and detailed photomultiplier tube response characterization. This result accurately predicts the timing and spatial distribution of light due to scintillation and Cherenkov emission in the detector. This is the first description of photon propagation in LAr to include several effects, including anomalous dispersion of the index of refraction near the ultraviolet resonance, Mie scattering from impurities, and Cherenkov light production.

Cherenkov detectors↗
DOE OSTI2024

Qualitative and quantitative enhancement of parameter estimation for model-based diagnostics using automatic differentiation with an application to inertial fusion

Parameter estimation using observables is a fundamental concept in the experimental sciences. Mathematical models that represent the physical processes can enable reconstructions of the experimental observables and greatly assist in parameter estimation by turning it into an optimization problem which can be solved by gradient-free or gradient-based methods. In this work, the recent rise in flexible frameworks for developing differentiable scientific computing programs is leveraged in order to dramatically accelerate data analysis of a common experimental diagnostic relevant to laser–plasma and inertial fusion experiments, Thomson scattering. A differentiable Thomson-scattering data analysis tool is developed that uses reverse-mode automatic differentiation (AD) to calculate gradients. By switching from finite differencing to reverse-mode AD, three distinct outcomes are achieved. First, gradient descent is accelerated dramatically to the extent that it enables near real-time usage in laser–plasma experiments. Second, qualitatively novel quantities which require $\mathcal{O}(10^3)$ parameters can now be included in the analysis of data which enables unprecedented measurements of small-scale laser–plasma phenomena. Third, uncertainty estimation approaches that leverage the value of the Hessian become accurate and efficient because reverse-mode AD can be used for calculating the Hessian.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1980

Results of a demonstration of the use of Differential Very Long Baseline Interferometry data for precise navigation of interplanetary spacecraft

A set of experiments in the use of Differential Very Long Baseline Interferometry for spacecraft navigation have been completed. Data using both Voyager spacecraft and a single quasar were acquired during the Jupiter encounter time period. The data were processed and analyzed in order to assess the navigation accuracy of Differential Very Long Baseline Interferometry. The paper focuses on the data reduction and techniques for assessing data quality and consistency.

Christensen, C. S.↗
NASA NTRS1980

Analysis of differential and active charging phenomena on ATS-5 and ATS-6

Spacecraft charging on the differential charging and artificial particle emission experiments on ATS 5 and ATS 6 were studied. Differential charging of spacecraft surfaces generated large electrostatic barriers to spacecraft generated electrons, from photoemission, secondary emission, and thermal emitters. The electron emitter could partially or totally discharge the satellite, but the mainframe recharged negatively in a few 10's of seconds. The time dependence of the charging behavior was explained by the relatively large capacitance for differential charging in comparison to the small spacecraft to space capacitance. A daylight charging event on ATS 6 was shown to have a charging behavior suggesting the dominance of differential charging on the absolute potential of the mainframe. Ion engine operations and plasma emission experiments on ATS 6 were shown to be an effective means of controlling the spacecraft potential in eclipse and sunlight. Elimination of barrier effects around the detectors and improving the quality of the particle data are discussed.

Olsen, R. C.↗
NASA NTRS1993

Investigation of the effects of extravehicular activity (EVA) gloves on performance

The objective was to assess the effects of extravehicular activity (EVA) gloves at different pressures on human hand capabilities. A factorial experiment was performed in which three types of EVA gloves were tested at five pressure differentials. The independent variables tested in this experiment were gender, glove type, pressure differential, and glove make. Six subjects participated in an experiment where a number of dexterity measures, namely time to tie a rope, and the time to assemble a nut and bolt were recorded. Tactility was measured through a two point discrimination test. The results indicate that with EVA gloves strength is reduced by nearly 50 percent, there is a considerable reduction in dexterity, performance decrements increase with increasing pressure differential, and some interesting gender glove interactions were observed, some of which may have been due to the extent (or lack of) fit of the glove to the hand. The implications for the designer are discussed.

Bishu, Ram R.↗
NASA NTRS1986

Development of a high-altitude airborne dial system: The Lidar Atmospheric Sensing Experiment (LASE)

The ability of a Differential Absorption Lidar (DIAL) system to measure vertical profiles of H2O in the lower atmosphere was demonstrated both in ground-based and airborne experiments. In these experiments, tunable lasers were used that required real-time experimenter control to locate and lock onto the atmospheric H2O absorption line for the DIAL measurements. The Lidar Atmospheric Sensing Experiment (LASE) is the first step in a long-range effort to develop and demonstrate an autonomous DIAL system for airborne and spaceborne flight experiments. The LASE instrument is being developed to measure H2O, aerosol, and cloud profiles from a high-altitude ER-2 (extended range U-2) aircraft. The science of the LASE program, the LASE system design, and the expected measurement capability of the system are discussed.

Browell, E. V.↗
NASA NTRS1996

Comments on SEE: Comparative Advantages and and Experimental Consequences

The Satellite Energy Exchange experiment measures the periodic, near-miss encounters between a sheppard satellite and a small test body (satellite) in approximately the same orbit about a primary. Several important experimental requirements have been chosen to enhance capabilities: (a) The satellite be flown in a sun-synchronous orbit at an altitude of about 1350 Km, (b) Passive temperature system stabilized by spacecraft axial rotation with sunshade baffles at the end of the spacecraft, (c) Test bodies with different material composition be available for experiments, (d) The containment spacecraft fly about the sheppard mass in a zero-g environment whereas the test bodies, experience average zero-g environment over an orbital period, (e) Primary attitude and station-keeping uses magnetic field alignment plus micro-Newton thrusters such as Field Emission Electric Propulsion, and (f) Very low power (nW) laser tracking systems minimize impulse delivered to test bodies. With the above conditions, SEE has the capabilities: (1) Long duration (several years life-time) flight experiment (2) Long-term, active (with historical time record), self-calibration of satellite mass distribution (capsule geodesy) over lifetime of the spacecraft. (3) Novel passive thermal stabilization systems designed to attain cryogenic temperatures around 78K. (4) Novel spacecraft stabilization systems. (5) Ability to measure G to 1 part in 10(exp 6-7) depending on ultimate duration of experiment. (6) Ability to place limits on both temporal and spacial variations on G. (7) Ability to set experimental limits on the Post Newtonian parameters (PPN) alpha(2) and zeta(2). (8) Ability to measure (or place limits on) the non Einsteinian eccentricity of the Earth-Sun system (and the parameter alpha(1)) for long duration flight. (9) Ability to measure Delta((dot)-G)/G to 1 part in 10(exp 12-13). The MiniSTEP, competes in a limited way with Project SEE. It is designed to improve the measurement of the equivalence principle by seven orders of magnitude using active, low temperature (1.8 K) cooling for SQUID based, differential superconducting circuits. The experiment consists of a small cylinder concentrically located within a larger cylinder at its null gravitational point. The satellite is operated in zero-g mode using four differential accelerometers consisting to two test bodies of different material composition. The SQUIDS are needed to measure test body motion to precisions of 10(exp -18) over a four orbit period. The entire satellite moves in a very precise zero-g mode since the accelerometers are rigidly attached to the satellite. This limits the experiment to an approximately six month due to limitations on helium storage used in cryogenic cooling and thrust control to maintain the zero-g operation.

Smalley, Larry L.↗
DOE OSTI2025

Energy dependence of polarized 𝛾⁢𝛾 → 𝑒 + ⁢ 𝑒− in peripheral Au+Au collisions at $\sqrt{s_{NN}}$ = 54.4 and 200 GeV with the STAR experiment at RHIC

We report the differential yields at mid-rapidity of the Breit-Wheeler process (𝛾⁢𝛾 → 𝑒 + ⁢𝑒 − ) in peripheral Au+Aucollisions at $\sqrt{s_{NN}}$ = 54.4 and 200 GeV with the STAR experiment at the Relativistic Heavy Ion Collider (RHIC), as a function of energy $\sqrt{s_{NN}}$, 𝑒 + ⁢𝑒 − transverse momentum 𝑝 T , 𝑝$^{2}_{T}$, invariant mass 𝑀 𝑒⁢𝑒 , and azimuthal angle. In the invariant mass range of 0.4 < 𝑀 𝑒⁢𝑒 < 2.6GeV/𝑐 2 at low transverse momentum (𝑝 T < 0.15GeV/𝑐), the yields increase while the pair √⟨𝑝$^{2}_{T}$⟩ decreases with increasing $\sqrt{s_{NN}}$, a feature that is correctly predicted by the QED calculation. Here, the energy dependencies of the measured quantities are sensitive to the nuclear form factor, infrared divergence and photon polarization. The data are compiled and used to extract the charge radius of the Au nucleus.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1980

Differential Very Long Baseline Interferometry (delta VLBI) spacecraft tracking system demonstration. Part 2: Data acquisition and processing

A set of experiments in the use of Differential Very Long Baseline Interferometry (delta VLBI) for spacecraft navigation were completed. Data using both Voyager spacecraft and a single quasar were acquired during the Jupiter encounter time period. The data were processed and analyzed to assess the navigation accuracy of delta VLBI. The data reduction and techniques for assessing data quality and consistency are discussed.

Christensen, C. S.↗
NASA NTRS1992

COBE Differential Microwave Radiometer (DMR) data processing techniques

The purpose of the Differential Microwave Radiometer (DMR) experiment on the Cosmic Background Explorer (COBE) satellite is to make whole-sky maps, at frequencies of 31.5, 53, and 90 GHz, of any departures of the Cosmic Microwave Background (CMB) from its mean value of 2.735 K. An elaborate software system is necessary to calibrate and invert the differential measurements, so as to make sky maps free from large scale systematic errors to levels less than a millionth of the CMB.

Jackson, P. D.↗
DOE OSTI2021

The J/&psi;-007 Experiment: A Search for the LHCB Charm Pentaquarks in Hall C at Jefferson Lab

In the Jefferson Lab E12-16-007 (J/&psi;- 007) experiment we measured the differential J/&psi; photo-production cross section as a function of photon energy, Ey and Mandelstam variable t- the momentum transfer from the initial photon to the produced J/&psi;- in the energy region where all the charm pentaquark states were discovered by the LHCb (Large Hadron Collider beauty) collaboration. The J/&psi;-007 experiment was conducted in the experimental Hall C of the Thomas Jefferson National Accelerator Facility using a high-intensity real photon beam generated by a 10.6 GeV incident electron beam traversing a copper radiator upstream of a liquid hydrogen target. Two arm spectrometers of Hall C, HMS (High Momentum Spectrometer), and SHMS (Super High Momentum Spectrometer) were used to detect the e + e - dilepton J/&psi; decay pairs in coincidence. The spectrometers' four momentum and angle settings scanned a photon beam energy range between 9.1 and 10.6 GeV and |t| up to 5 GeV 2 . An enhanced sensitivity to the s-channel resonant J/&psi; photo-production was achieved by optimizing the spectrometer settings at a higher t region where the non-resonant standard t-channel J/&psi; production cross section is strongly suppressed. No evidence for pentaquarks was observed and, the cross section upper limits for each LHCb pentaquark candidate were determined and are presented in this document.

Duran, Burcu↗
NASA NTRS1969

Some aspects of remote atmospheric sensing by laser radar

An analysis has been made of some aspects of atmospheric sensing by laser radar spectroscopy. A discussion of the laser radar equation is presented which leads to methods for obtaining atmospheric information by spectroscopic means. Calculations are presented which investigate the potential of Doppler, Raman and differential absorption techniques. It is concluded that atmospheric measurements based upon Doppler and Raman approaches are restricted to qualitative studies at the present time primarily because of the limitations imposed by existing laser sources and detectors. It is probable that these limitations will be removed in the near future and it is recommended that exploratory experiments be continued. The differential absorption method for obtaining the spatial distribution of atmospheric gases is well developed for such gases as water vapor and oxygen where the basic laser frequency lies close to the center of the particular absorption line. Further investigation is recommended in the field of laser frequency shifting. Additional information is also required on the shape of the absorption line, particular in the region where the line reflects both pressure and Doppler broadening.

Schotland, R. M.↗