Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DSC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 127 records · Page 7

Assessment of a novel ternary eutectic chloride salt for next generation high-temperature sensible heat storage

A novel ternary eutectic salt mixture for high-temperature sensible heat storage, composed of sodium chloride, potassium chloride and magnesium chloride (NaKMg-Cl) was developed based on a phase diagram generated with FactSage(R). The differential scanning calorimetry (DSC) technique was used to experimentally validate the predicted melting point of the ternary eutectic composition, which was measured as 387 degrees C, in good agreement with the prediction. The ternary eutectic was compared to two binary salts formulated based on prediction of the eutectic composition by FactSage, but unfortunately DSC measurements showed that neither binary salt composition was eutectic. Nonetheless, the measured thermo-physical properties of the ternary and the two binary mixtures are compared. Liquid heat capacities of both the ternary and binary salts were determined by using DSC with sapphire as the standard reference. The average heat capacity of the ternary mixture was recorded as 1.18 J g -1 K -1 . The mass loss of the molten eutectic salts was studied up to 1000 degrees C using a thermogravimetric analyser in nitrogen, argon and air. The results showed a significant mass loss due to vaporisation in an open system, particularly above 700 degrees C. However, simulation of mass loss in a closed system with an inert cover gas indicates storage temperatures above 700 degrees C may be feasible, and highlights the importance of the design of the storage tank system. In terms of storage material cost, the NaKMg-Cl mixture is approximately 4.5 USD/kWh, which is 60% cheaper than current state-of-the-art nitrate salt mixtures.

14 SOLAR ENERGY↗

Non-isothermal melting of ice in the gas-diffusion layer of a proton-exchange-membrane fuel cell

Non-isothermal ice melting in the fibrous gas-diffusion layer (GDL) of a proton-exchange-membrane fuel cell (PEMFC) is investigated using differential scanning calorimetry (DSC). Non-isothermal ice-melting rates and ice-melting times are obtained from heat-flow measurements in water-saturated Toray GDLs at heating rates of 1, 2.5, 5, 10, and 25 K/min. In all cases, ice-melting times decrease nonlinearly with increasing heating rate. Nevertheless, melting temperatures remain at 272.9 ± 0.5 and 272.7 ± 0.4 K for bulk ice and ice within the GDL, respectively, reiterating that melting is thermodynamic-based at a rate limited by heat transfer. The slight GDL ice melting-point depression is consistent with the Gibbs-Thomson equation for equilibrium melting using an average pore diameter of 30 μm. Ice-melting endotherms are predicted from overall DSC energy balances coupled with a moving-boundary Stefan problem, where an ice-melting front within a GDL propagates with volume-averaged properties through an effective medium. Agreement between DSC experiment and theory is excellent. The proposed model accurately predicts ice-melting endotherms for Toray GDLs with two ice saturations and for bulk ice. Further, a pseudo-steady-state analysis obtains an analytical expression for ice-melting time, which is controlled by the time for heat addition to the propagating solid/liquid interface. Significantly, the new expression elucidates parameters controlling ice melting and allows for better design of both GDL materials and heating strategies to enhance the success of PEMFC cold-start.

25 ENERGY STORAGE↗

A System for Continual Quality Improvement of Normal Tissue Delineation for Radiation Therapy Treatment Planning

Purpose: To implement the 'plan-do-check-act' (PDCA) cycle for the continual quality improvement of normal tissue contours used for radiation therapy treatment planning. Methods and Materials: The CT scans of patients treated for tumors of the brain, head and neck, thorax, pancreas and prostate were selected for this study. For each scan, a radiation oncologist and a diagnostic radiologist, outlined the normal tissues ('gold' contours) using Radiation Therapy Oncology Group (RTOG) guidelines. A total of 30 organs were delineated. Independently, 5 board-certified dosimetrists and 1 trainee then outlined the same organs. Metrics used to compare the agreement between the dosimetrists' contours and the gold contours included the Dice Similarity Coefficient (DSC), and a penalty function using distance to agreement. Based on these scores, dosimetrists were re-trained on those organs in which they did not receive a passing score, and they were subsequently re-tested. Results: Passing scores were achieved on 19 of 30 organs evaluated. These scores were correlated to organ volume. For organ volumes <8 cc, the average DSC was 0.61 vs organ volumes {>=}8 cc, for which the average DSC was 0.91 (P=.005). Normal tissues that had the lowest scores included the lenses, optic nerves, chiasm, cochlea, and esophagus. Of the 11 organs that were considered for re-testing, 10 showed improvement in the average score, and statistically significant improvement was noted in more than half of these organs after education and re-assessment. Conclusions: The results of this study indicate the feasibility of applying the PDCA cycle to assess competence in the delineation of individual organs, and to identify areas for improvement. With testing, guidance, and re-evaluation, contouring consistency can be obtained across multiple dosimetrists. Our expectation is that continual quality improvement using the PDCA approach will ensure more accurate treatments and dose assessment in radiotherapy treatment planning and delivery.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Adaptive Breast Radiation Therapy Using Modeling of Tissue Mechanics: A Breast Tissue Segmentation Study

Purpose: To validate and compare the accuracy of breast tissue segmentation methods applied to computed tomography (CT) scans used for radiation therapy planning and to study the effect of tissue distribution on the segmentation accuracy for the purpose of developing models for use in adaptive breast radiation therapy. Methods and Materials: Twenty-four patients receiving postlumpectomy radiation therapy for breast cancer underwent CT imaging in prone and supine positions. The whole-breast clinical target volume was outlined. Clinical target volumes were segmented into fibroglandular and fatty tissue using the following algorithms: physical density thresholding; interactive thresholding; fuzzy c-means with 3 classes (FCM3) and 4 classes (FCM4); and k-means. The segmentation algorithms were evaluated in 2 stages: first, an approach based on the assumption that the breast composition should be the same in both prone and supine position; and second, comparison of segmentation with tissue outlines from 3 experts using the Dice similarity coefficient (DSC). Breast datasets were grouped into nonsparse and sparse fibroglandular tissue distributions according to expert assessment and used to assess the accuracy of the segmentation methods and the agreement between experts. Results: Prone and supine breast composition analysis showed differences between the methods. Validation against expert outlines found significant differences (P<.001) between FCM3 and FCM4. Fuzzy c-means with 3 classes generated segmentation results (mean DSC = 0.70) closest to the experts' outlines. There was good agreement (mean DSC = 0.85) among experts for breast tissue outlining. Segmentation accuracy and expert agreement was significantly higher (P<.005) in the nonsparse group than in the sparse group. Conclusions: The FCM3 gave the most accurate segmentation of breast tissues on CT data and could therefore be used in adaptive radiation therapy-based on tissue modeling. Breast tissue segmentation methods should be used with caution in patients with sparse fibroglandular tissue distribution.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Evaluation of 4-dimensional Computed Tomography to 4-dimensional Cone-Beam Computed Tomography Deformable Image Registration for Lung Cancer Adaptive Radiation Therapy

Purpose: To evaluate 2 deformable image registration (DIR) algorithms for the purpose of contour mapping to support image-guided adaptive radiation therapy with 4-dimensional cone-beam CT (4DCBCT). Methods and Materials: One planning 4D fan-beam CT (4DFBCT) and 7 weekly 4DCBCT scans were acquired for 10 locally advanced non-small cell lung cancer patients. The gross tumor volume was delineated by a physician in all 4D images. End-of-inspiration phase planning 4DFBCT was registered to the corresponding phase in weekly 4DCBCT images for day-to-day registrations. For phase-to-phase registration, the end-of-inspiration phase from each 4D image was registered to the end-of-expiration phase. Two DIR algorithms—small deformation inverse consistent linear elastic (SICLE) and Insight Toolkit diffeomorphic demons (DEMONS)—were evaluated. Physician-delineated contours were compared with the warped contours by using the Dice similarity coefficient (DSC), average symmetric distance, and false-positive and false-negative indices. The DIR results are compared with rigid registration of tumor. Results: For day-to-day registrations, the mean DSC was 0.75 ± 0.09 with SICLE, 0.70 ± 0.12 with DEMONS, 0.66 ± 0.12 with rigid-tumor registration, and 0.60 ± 0.14 with rigid-bone registration. Results were comparable to intraobserver variability calculated from phase-to-phase registrations as well as measured interobserver variation for 1 patient. SICLE and DEMONS, when compared with rigid-bone (4.1 mm) and rigid-tumor (3.6 mm) registration, respectively reduced the average symmetric distance to 2.6 and 3.3 mm. On average, SICLE and DEMONS increased the DSC to 0.80 and 0.79, respectively, compared with rigid-tumor (0.78) registrations for 4DCBCT phase-to-phase registrations. Conclusions: Deformable image registration achieved comparable accuracy to reported interobserver delineation variability and higher accuracy than rigid-tumor registration. Deformable image registration performance varied with the algorithm and the patient.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Synthesis Structure and Characterization of the n=4 Aurivillius Phase Bi5Ti3CrO15

The n=4 Aurivillius phase, Bi{sub 5}Ti{sub 3}CrO{sub 15}, was synthesized by solid state reaction. Rietveld analysis of high resolution neutron diffraction data demonstrated this material to adopt the polar space group A2{sub 1}am at room temperature, transforming to the aristotype I4/mmm structure above 650 C. This phase transition is coincident with an anomaly in DSC signal and relative permittivity, which are characteristic of a ferroelectric-paraelectric phase transition. Bi{sub 5}Ti{sub 3}CrO{sub 15} exhibits paramagnetic behavior at low temperature, with short range antiferromagnetic interactions, but no evidence for long range magnetic ordering. This is considered a consequence of significant disorder of Ti and Cr over the available octahedral sites, as demonstrated by analysis of neutron diffraction data.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermally stimulated crystallization of (20-x)LiO{sub 2}-80TeO{sub 2}-xWO{sub 3} glass system

Tellurite glasses of the (20-x)LiO{sub 2}-80TeO{sub 2}-xWO{sub 3} system were synthesized (x=0, 5, and 10) and annealed at different temperatures, and the crystallization kinetics was studied using XRD, FTIR spectroscopy, and DSC techniques. XRD data evidenced the amorphous state of as-quenched samples, while thermally treated samples showed the growth of crystalline phases. FTIR spectroscopy was used to observe the evolution of the vibrational mode assigned to the TeO{sub 2} phases. The presence of {gamma}-TeO{sub 2}, {alpha}-TeO{sub 2}, and {alpha}-Li{sub 2}Te{sub 2}O{sub 5} crystalline phases was observed for the sample TL, x=0, while only the first and second phases were observed for TLW5 and TLW10 samples, x=5 and 10, respectively, suggesting that WO{sub 3} enters the structure preferentially as glass former, inhibiting the growth of the phase {alpha}-Li{sub 2}Te{sub 2}O{sub 5}. -- Graphical abstract: Typical DSC thermogram for TLW glasses for different heating rates with insert graphic showing as the Tg is evaluated. Display Omitted Highlights: {yields} The crystallization kinetics was studied using XRD, FTIR spectroscopy, and DSC techniques. {yields} The glass transition and maximum crystallization temperatures increase when the WO{sub 3} content in the glass composition was increased. {yields} The observed asymmetry of crystallization peaks suggests an overlapping of distinct crystallization phases ({alpha}- and {gamma}-TeO{sub 2}). {yields} The WO{sub 3} enters the structure as glass former and does not participate in the crystallization of glass.

36 MATERIALS SCIENCE↗

K[AsW{sub 2}O{sub 9}], the first member of the arsenate–tungsten bronze family: Synthesis, structure, spectroscopic and non-linear optical properties

K[AsW{sub 2}O{sub 9}], prepared by high-temperature solid-state reaction, is the first member of the arsenate–tungsten bronze family. The structure of K[AsW{sub 2}O{sub 9}] is based on a 3-dimensional (3D) oxotungstate–arsenate framework with the non-centrosymmetric P2{sub 1}2{sub 1}2{sub 1} space group, a=4.9747(3) Å, b=9.1780(8) Å, c=16.681(2) Å. The material was characterized using X-ray diffraction, scanning electron microscopy (SEM), differential scanning calorimetry (DSC), Raman and infrared (IR) spectroscopic techniques. The results of DSC demonstrate that this phase is stable up to 1076 K. Second harmonic generation (SHG) measurements performed on a powder sample demonstrate noticeable (0.1 of LiIO{sub 3}) non-linear optical (NLO) activity. - Graphical abstract: K[AsW{sub 2}O{sub 9}], the first member of arsenate–tungsten bronze family exhibit new three dimensional structure type, significant thermal stability and NLO properties. Highlights: • K[AsW{sub 2}O{sub 9}], the first member of the arsenate–tungsten bronze family was synthesized with solid state reaction technique. • Structure of this phase was investigated with X-ray diffraction, IR and Raman spectroscopy and electron microscopy. • Thermal stability of the phase was determinate with DSC techniques. • NLO properties were investigated.

36 MATERIALS SCIENCE↗

Crystal structures and thermodynamics/kinetics of Zn(II) coordination polymers with helical chains

Solvothermal reactions of Zn(II) acetates and four V-shaped carboxylates ligands in the presence of 1,4-Bis(2-methyl-imidazol-1-yl)butane afforded four interesting Zn(II) coordination polymers with helical chains, namely, {[Zn(bib)(atibdc)]·2H_2O}{sub n} (1), {[Zn(bib)(atbip)]·H_2O}{sub n} (2), {[Zn(bib)(2,2′-tda)]}{sub n} (3) and {[Zn(bib)(5-tbipa)]·EtOH}{sub n} (4), (H{sub 2}atibdc=5-amino-2,4,6-triiodoisophthalic acid, H{sub 2}atbip=5-amino-2,4,6-tribromoisophthalic acid, 2,2′-H{sub 2}tad=2,2′-thiodiacetic acid, 5-H{sub 2}tbipa=5-tert-butyl-isophthalic acid). 1 reveals a 3D chiral framework with three kinds of helical chains along a, b and c axis. 2 shows a 2D step-type chiral framework with right-handed helical chains. 3 displays a wavelike 2D layer network possessing alternate left- and right-handed helical chains. 4 presents a four-connected 3D framework with zigzag and meso-helical chains. The different spacers and substituent group of carboxylic acid ligands may lead to the diverse network structures of 1–4. The fluorescent properties of complexes 1−4 were studied. In addition, the thermal decompositions properties of 1–4 were investigated by simultaneous TG/DTG–DSC technique. The apparent activation energy E and the pre-exponential factor (A) of skeleton collapse for the complexes 1–4 are calculated by the integral Kissinger's method and Ozawa–Doyle's method. The activation energy E (E{sub 1}=209.658 kJ·mol{sup −1}, E{sub 2}=250.037 kJ mol{sup −1}, E{sub 3}=225.300 kJ mol{sup −1}, E{sub 4}=186.529 kJ·mol{sup −1}) demonstrates that the reaction rate of the melting decomposition is slow. The thermodynamic parameters (ΔH{sup ‡}, ΔG{sup ‡} and ΔS{sup ‡}) at the peak temperatures of the DTG curves were also calculated. ΔG{sup ‡}>0 indicates that the skeleton collapse is not spontaneous. ΔH{sub d}>0 suggests that the skeleton collapse is endothermic, corresponding to the intense endothermic peak of the DSC curve. The structural stability could be illustrated from the point of thermodynamics and kinetics. - Graphical abstract: Four new zinc coordination architectures constructed from the primary ligand bib, transition metal ions Zn(II) and four V-shaped carboxylate coligands. The different structural evolutions of complexes 1–4 have systematically illustrated that the carboxylate coligands play a critical role in the assemblies of the CPs. Their thermal decompositions properties of 1–4 were investigated by simultaneous TG/DTG–DSC technique. The apparent activation energy E and the pre-exponential factor (A) of skeleton collapse for the complexes 1−4 are calculated by the integral Kissinger’s method and Ozawa–Doyle’s method. The structural stability could be illustrated from the point of thermodynamics and kinetics. Display Omitted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Calorimetric study on mechanically milled aluminum and multiwall carbon nanotube composites

Pure aluminum reinforced with carbon nanotube (CNT) composites have been prepared by high energy attritor milling up to 48 hrs. Differential Scanning Calorimetry (DSC) has been carried out to investigate apparent activation energy and order of the reaction between carbon nanotubes and aluminum by Kissinger equation and Crane equation under non-isothermal conditions. The DSC results clearly reveal that an exothermic reaction occurs before the melting of aluminum. The effect of milling time on the initiation of this exothermic reaction has been studied. The peak temperature of the reaction of carbon nanotubes and aluminum is found to depend on the heating rate during the continuous heating. Apparent activation energy was found to get doubled after milling for 36 hrs compared to 24 hrs milled samples. The mechanism of the reaction kinetics which depends on reaction order is instantaneous nucleation and one dimensional growth for both samples. Formation of Al{sub 4}C{sub 3} was confirmed by X-ray diffraction (XRD) of as-milled powders and after performing DSC of the milled powders. Highlights: {yields} Attritor milling used for processing Al-CNT composites. {yields} Powder morphology as a function of time studied. {yields} Apparent activation energy and order of the reaction calculated for Al{sub 4}C{sub 3} formation. {yields} Apparent activation energy increases two fold with increase in milling time from 24 to 36 hours.

36 MATERIALS SCIENCE↗

Microstructural, mechanical and electrochemical behaviour of a 7017 Al–Zn–Mg alloy of different tempers

The aim of the investigation is to assess the microstructural features and associated physical, mechanical and electrochemical properties of a 7017 Al–Zn–Mg alloy of various tempers. A 7017 Al–Zn–Mg alloy was subjected to different ageing schedules to produce under-(T4), peak-(T6), over-(T7) and highly over-aged tempers. Optical microscopy, hardness measurement, electrical conductivity measurement, tensile testing and SEM fractographs, differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and electrochemical polarization studies have been used to characterize the alloy tempers. Hardness measurement and tensile testing showed the characteristic age hardening phenomenon of aluminium alloys. Optical and TEM micrographs have revealed the variation in size of matrix strengthening η′ (MgZn{sub 2}) and also the size and distribution of grain boundary η (MgZn{sub 2}) precipitate with ageing time. DSC thermograms exhibiting exothermic and endothermic peaks indicated the characteristic solid state reaction sequence of the 7017 alloy. Potentiodynamic polarization study of the 7017 alloy of various tempers in 3.5 wt.% NaCl solution at near neutral pH showed typical active metal dissolution behaviour, but at pH 12 an active–passive–transpassive transition behaviour has been observed. - Graphical abstract: TEM micrograph of the 7017 aluminium alloy of various tempers (a, b) under aged (T4), (c, d) peak aged (T6), (e, f) over aged (T7) and (g, h) highly over-aged. Display Omitted - Highlights: • 7017 Al-Zn-Mg alloy was subjected to different artificial ageing treatments. • Characterization of 7017 alloy tempers by hardness, tensile, DSC, TEM and electrochemical behaviour. • Structure-properties relationship of the 7017 Al-Zn-Mg alloy of various tempers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characterization, properties and catalytic application of TiO{sub 2} nanotubes prepared by ultrasonic-assisted sol-hydrothermal method

Graphical abstract: A novel class of titania nanotubes (TNTs) have been prepared by ultrasonic assisted sol-hydrothermal method using tetrabutyl titanate and ethanol as the precursors. The physicochemical characteristics of the catalysts were investigated by transmission electron microscopy, X-ray diffraction, Brunauer–Emmett–Teller method, Differential Scanning Calorimeters-Thermogravimetric Analysis (DSC–TG) and UV–vis absorption spectra. The photocatalytic activity of the products was evaluated in terms of reactive brilliant red X-3B in an aqueous solution under UV irradiation for 1 h. The results showed that the catalyst revealed an excellent photocatalytic activity. The degradation rate of reactive brilliant X-3B could be up to 96%. Display Omitted Highlights: ► TiO{sub 2} nanotubes were prepared by ultrasonic-assisted sol-hydrothermal method. ► TEM, HRTEM, XRD, and BET were used to study morphology and crystalline structure. ► FTIR, DSC-TG was used to investigate pyrolytic process and phase structure. ► UV–vis absorption spectra were used to evaluate the photocatalysis of catalysts. ► Dye degradation result showed that the catalyst had excellent photocatalytic activity. -- Abstract: A novel class of titania nanotubes (TNTs) have been prepared by ultrasonic assisted sol-hydrothermal method using tetrabutyl titanate and ethanol as the precursors. The physicochemical characteristics of the catalysts were investigated by transmission electron microscopy (TEM), X-ray diffraction (XRD), Brunauer–Emmett–Teller (BET) method, Differential Scanning Calorimeters-Thermogravimetric Analysis (DSC-TG) and UV–vis absorption spectra. The photocatalytic activity of the products was evaluated in terms of reactive brilliant red X-3B in an aqueous solution under UV irradiation for 1 h. The results showed that the anatase nanotubes prepared by ultrasonic assisted sol-hydrothermal method exhibited excellent photocatalytic activity. The degradation rate of reactive brilliant X-3B could be up to 96%. The high degradation rate was attributed to the good crystalline pure-phase structure of nanotubes caused by ultrasound. Furthermore, the large surface areas also played an important role in the high degradation rate.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Thermodynamic investigation of the NaCl-KCl salt system from 25 to 950 °C

NaCl-KCl molten salt system has been proposed as a primary component of several promising heat transfer eutectics and fuel host for Generation IV molten salt reactors (MSR). In this work, several key thermodynamic parameters, including high temperature enthalpies, isobaric heat capacities (C p ) and molar enthalpies of mixing (ΔH mix ), of the NaCl -KCl system (NaCl, 75mol% NaCl – 25mol% KCl, 51mol% NaCl – 49mol% KCl, 25mol% NaCl – 75mol% KCl, and KCl) were measured by high temperature drop calorimetry (HTDC) utilizing laser sealed nickel and aluminum crucibles. Salts were checked for phase purity by X-ray diffraction (XRD), and water content by Karl Fischer coulometric titrimetry and thermogravimetric analysis (TGA). Thermo-mechanical analysis (TMA) utilizing custom-built boron nitride (BN) crucibles was employed to determine temperatures of phase transitions (solid $\rightarrow$ liquid) for the salts and plotted against the pseudobinary phase diagram for the NaCl-KCl system. Small deviations (3-10 %) were found among C p values obtained from HTDC, differential scanning calorimetry (DSC), and NIST, comparable to the average uncertainty based on two standard deviations of measured data that are ~6% for DSC and ~3% for HTDC. Additionally, the measured enthalpies and C p values of mixed NaCl-KCl salts (e.g., 51mol% NaCl – 49mol% KCl eutectic) were shown to behave as statistical mixtures of its pure endmembers, consistent with ΔH mix = ~ 0 kJ/mol at 800 °C, and a regular interaction parameter of Ω = 1.20 ± 0.76 kJ/mol. In conclusion, this study represents a step towards improved accuracy and precision in determinations of thermodynamic parameters of molten salts by using DSC, TMA, and HTDC, in completion of the Molten Salt Thermal Properties Database (MSTDB).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermodynamic modeling of CsF with LiF-NaF-KF for molten fluoride-fueled reactors

Gibbs energy models were developed to describe the thermochemical behavior of CsF in molten FLiNaK (46.5LiF-11.5NaF-42KF mol%), a proposed molten salt reactor (MSR) fuel solvent and coolant, as cesium is of concern due to its high radiotoxicity and volatility. Initially, it was necessary to obtain a more accurate Gibbs energy function for CsF which required fitting parameters to reported vapor pressures over condensed phase CsF. The pseudo-binary systems CsF-LiF, CsF-NaF and CsF-KF were then evaluated utilizing phase equilibria and enthalpy of mixing (Δ mix H) values, together with original differential scanning calorimetry (DSC) measurements performed for the CsF-LiF and CsF-KF systems. The CsF-LiF-NaF, CsF-LiF-KF and CsF-NaF-KF pseudo-ternary system representations were obtained by interpolation of the constituent pseudo-binary systems, with DSC measurements performed for the CsF-LiF-NaF system to corroborate the calculated liquidus temperature. Ultimately, the pseudo-ternary systems were interpolated to obtain Gibbs energy models for the pseudo-quaternary CsF-LiF-NaF-KF system, supported by DSC measurements at low CsF compositions (1–10 mol%), yielding computed equilibria and cesium-containing vapor pressures that compare favorably with reported values. In conclusion, the Molten Salt Thermal Properties Database – Thermochemical (MSTDB-TC) was subsequently expanded to include these Gibbs energy models allowing description of the thermochemical behavior of the CsF-LiF-NaF-KF system.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Hexamethylene dilauroyl, dimyristoyl, and dipalmytoyl amides as phase change materials for thermal energy storage

Hexamethylene dilauroyl, dimyristoyl, and dipalmytoyl amides have been produced as solid-liquid phase change materials via condensation of hexamethylene diamine with the respective acyl chlorides (lauroyl chloride, myristoyl chloride, and palmytoyl chloride) and were characterized by FT-IR, NMR, DSC, and TG analysis. Hexamethylene dilauroyl, dimyristoyl, and dipalmytoyl amides crystallized due to structural symmetry and flexibility of long alkyl groups. They were characterized by DSC and FT-IR spectroscopy before and after thermal cycling to determine their thermal reliability. Phase change enthalpies were found 110.1 and -103.3 J g{sup -1} for hexamethylene dilauroyl amide (N,N'-hexamethylene didodecanamide), 116.9 and -110.4 J g{sup -1} for hexamethylene dimyristoyl amide (N,N'-hexamethylene ditetradecanamide), and 144.5 and -140.5 J g{sup -1} for hexamethylene dipalmytoyl amides (N,N'-hexamethylene dihexadecanamide) by DSC. The endurance of hexamethylene dilauroyl, dimyristoyl, and dipalmytoyl amides was studied by TG analysis. (author)

25 ENERGY STORAGE↗

An Efficient Copper-Based Redox Shuttle Bearing a Hexadentate Polypyridyl Ligand for DSCs under Low-Light Conditions

A Cu complex featuring a hexadentate ligand was synthesized and evaluated as a redox shuttle in dye-sensitized solar cell (DSC) devices, which exhibited excellent performance under low-light conditions. Cu-based redox shuttles (RSs) have been shown to perform remarkably well under low-light conditions; however, most of the known Cu-based RSs employ bidentate pyridyl ligands and often require bulky flanking groups adjacent to the nitrogen donors of these ligands to prevent distortion and binding of exogenous Lewis bases such as 4- tert -butylpyridine (TBP) that are added to enhance cell performance. Without the bulky substituents, the bidentate ligands are susceptible to ligand exchange with TBP. In this context, we have developed a Cu-based RS with a preorganized multidentate ligand designed to facilitate efficient electron transfer kinetics and high stability via the chelate effect. The Cu system, [Cu(bpyPY4)] 2+/+ , reported here is supported by the hexadentate polypyridyl ligand bpyPY4 (6,6'-bis(1,1-di(pyridine-2-yl)ethyl)-2,2'-bipyridine) and examined as a RS in DSCs. From X-ray crystallography and variable-temperature 1 H NMR studies, bpyPY4 provides a dynamic coordination environment around the metal center. Cyclic voltammetry and UV–visible and NMR spectroscopy indicate that noncoordinated pyridyl donors block binding of TBP to copper. DSC devices using [Cu(bpyPY4)] 2+/+ as the redox electrolyte gave a power conversion efficiency (PCE) value of 4.9% under 1 sun illumination (100 mW/cm 2 ). Strikingly, the device performance increased to 11.11% when irradiated with 2400 lux (0.5 mW/cm 2 ) via a fluorescent lamp light source and improved further to 15.2% PCE at 13500 lux (2.10 mW/cm 2 ). In conclusion, the Cu redox shuttle is an intriguing candidate for implementation with narrow band gap sensitizers with low oxidation potentials, which are important for high photocurrent DSC devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Discovery of S···C≡N Intramolecular Bonding in a Thiophenylcyanoacrylate-Based Dye: Realizing Charge Transfer Pathways and Dye···TiO 2 Anchoring Characteristics for Dye-Sensitized Solar Cells

Donor-pi-acceptor dyes containing thiophenyl pi-conjugated units and cyanoacrylate acceptor groups are among the best-performing organic chromophores used in dye-sensitized solar cell (DSC) applications. Yet, the molecular origins of their high photovoltaic output have remained unclear until now. This synchrotron-based X-ray diffraction study elucidates these origins for the high-performance thiophenylcyanoacrylate-based dye MK-2 (7.7% DSC device efficiency) and its molecular building block, MK-44. The crystal structures of MK-2 and MK-44 are both determined, while a high-resolution charge-density mapping of the smaller molecule was also possible, enabling the nature of its bonding to be detailed. A strong S center dot center dot center dot C equivalent to N intramolecular interaction is discovered, which bears a bond critical point, thus proving that this interaction should be formally classified as a chemical bond. A topological analysis of the pi-conjugated portion of MK-44 shows that this S center dot center dot center dot C equivalent to N bonding underpins the highly efficient intramolecular charge transfer(ICT) in thiophenylcyanoacrylate dyes. This manifests as two bipartite ICT pathways bearing carboxylate and nitrile end points. In turn, these pathways dictate a preferred COO/CN anchoring mode for the dye as it adsorbs onto TiO2 surfaces, to form the dye TiO2 interface that constitutes the DSC working electrode. These results corroborate a recent proposal that all cyanoacrylate groups anchor onto TiO2 in this COO/CN binding configuration. Conformational analysis of the MK-44 and MK-2 crystal structures reveals that this S center dot center dot center dot C equivalent to N bonding will persist in MK-2. Accordingly, this newly discovered bond affords a rational explanation for the attractive photovoltaic properties of,MK-2. More generally, this study provides the first unequivocal evidence for an S center dot center dot center dot C equivalent to N interaction, confirming previous speculative assignments of such interactions in other compounds.

charge-density mapping↗

Kerogen Swelling and Confinement: Its implication on Fluid Thermodynamic Properties in Shales

Type I kerogen was isolated from Green River Shale and characterized using SEM, TGA, DSC, and nitrogen adsorption. The swelling behavior of this kerogen with decane was analyzed using traditional test-tube swelling experiment and Dynamic Light Scattering. The TGA and DSC were used to analyze the thermodynamic behavior of decane that was sorbed in the kerogen and show that kerogen suppresses the boiling point of decane due to the effect of confinement. However, the suppression is larger when oil (a multicomponent mixture) was used, possibly due to the combined effect of differential uptake of components by kerogen (kerogen prefers and sorbs polars and aromatics more than saturates, leading to splitting of oil into a sorbed and a free phase) and confinement in nano pores. Test-tube swelling, TGA, and DSC experiments were also performed on pyridine(polar-aromatic)-swelled kerogen. The combined and individual contributions from the two effects (the effect of confinement and differential uptake of hydrocarbon components) on properties of liquid in contact with kerogen, are studied in this work. Molecular Dynamics (MD) simulations revealed the variation in the swelling of type II kerogen in the presence of same amount of different liquids (differential swelling of kerogen).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗